Professional Documents
Culture Documents
171-148524 Catalogue
171-148524 Catalogue
61.1:657
D100087X012
August 2009 657 and 667 Actuators
Features
D Application Versatility—Five actuator types in
eleven sizes are available for an extensive variety of
applications. Spring rates, travel stops, and manual
operators are available for nearly any control valve
application. W2174-2/IL
W1916-3/IL
www.Fisher.com
Product Bulletin
61.1:657
657 and 667 Actuators August 2009
Accessories
Handwheels
Handwheels for diaphragm actuators are often used
Available Configurations as adjustable travel stops. They also provide a ready
means of positioning the control valve in an
emergency. The specifications in tables 5 and 6
apply to handwheels on both 657 and 667 Series
Direct Action actuators. For repeated or daily manual operation,
the unit should be equipped with a side-mounted
All 657 actuators are direct acting. Applying air handwheel actuator.
pressure to the upper diaphragm casing forces the
actuator stem downward. When this pressure is Top-Mounted Handwheels—Typical 657 and 667
reduced, the opposing spring force moves the actuators with handwheels mounted on the
actuator stem upward. Should the loading pressure diaphragm case are shown in figure 3 (not available
fail, the spring forces the stem to the extreme on a 667 actuator, size 80). On the 657 actuator, the
upward position. This provides fail-open action for handwheel can be set to limit the travel in the
push-down-to-close valves and fail-closed action for upward direction; on the 667 actuator, travel in the
push-down-to-open valves. downward direction can be restricted. A P-2 travel
stop (figure 5) is available for a 667 actuator, sizes
657—A direct-acting actuator used on sliding-stem 45-60 to limit travel in either the upward or
valves. Available in sizes 30 through 100. See downward directions. An actuator with a P-2 travel
figures 1, 2, 3, 6, and 7. stop is limited to a maximum travel of 19 mm (0.75
inch). The handwheel on the size 100 is similar in
function to those on the smaller sizes, but it uses a
657-4—A 657 actuator in sizes 70 and 87, designed gear drive similar to the drive employed on the
with 102 mm (4-inch) travel. integral side-mounted handwheels (see figure 3).
2
Product Bulletin
61.1:657
August 2009 657 and 667 Actuators
DIAPHRAGM CASINGS
DIAPHRAGM
DIAPHRAGM PLATE
ACTUATOR SPRING
ACTUATOR STEM
SPRING SEAT
SPRING ADJUSTOR
STEM CONNECTOR
YOKE
INDICATOR SCALE
W0364-2/IL W0363-2/IL
W0366-1/IL
3
Product Bulletin
61.1:657
657 and 667 Actuators August 2009
Table 1. Additional Specifications for Fisher 657 and 667 Series Actuators
EFFECTIVE YOKE MAXIMUM
STEM MAXIMUM
ACTUATOR DIAPHRAGM BOSS ALLOWABLE
DIA TRAVEL
SIZE AREA DIAMETER THRUST(1)
cm2 mm N
30 297 54 9.5 19 10,231
34 445 54 9.5 29 10,231
40 445 71 12.7 38 12,010
45 677 71 12.7 51 25,132
46 1006 71 12.7 51 33,584
50 677 90 19.1 51 25,131
60 1006 90 19.1 51 30,246
76
70(2) 1419 90 19.1 39,142
102(3)
76(667) 1006 90 19.1 51 30,246
25.4 63,392
80 1761 127 76
31.8 88,075(4)
76
87(2) 1419 127 25.4 39,142
102(3)
127H(5) 31.8
100 2902 102 200,160
178 50.8
Inch2 Inch Lb
30 46 2-1/8 3/8 0.75 2300
34 69 2-1/8 3/8 1.125 2300
40 69 2-13/16 1/2 1.5 2700
45 105 2-13/16 1/2 2 5650
46 156 2-13/16 1/2 2 7550
50 105 3-9/16 3/4 2 5650
60 156 3-9/16 3/4 2 6800
3
70(2) 220 3-9/16 3/4 8800
4(3)
76(667) 156 3-9/16 3/4 2 6800
1 14,150
80 273 5 3
1-1/4 19,800(4)
3
87(2) 220 5 1 8800
4(3)
5H(5) 1-1/4
100 450 4 45,000
7 2
1. These values are based on material limitations such as yoke, stem connection, diaphragm plate, and travel stop strengths.
2. Values also apply to 657-4 and 667-4 actuators.
3. For 657-4 and 667-4 actuator constructions.
4. Steel construction.
5. H=Heavy actuator-to-valve bolting.
4
Product Bulletin
61.1:657
August 2009 657 and 667 Actuators
Table 2. Volumetric Casing Displacement for Fisher 657 and 667 Series Actuators
ACTUATOR
CLEARANCE TRAVEL, mm
SIZE
VOLUME(1)
11 16 19 29 38 51 76 102
cm3 Casing Volume(2), cm3
30 540 918 1080 1180 --- --- --- --- ---
34 and 40 934 1470 1700 1850 2330 2790 --- --- ---
45 and 50 1560 --- 2790 3000 3720 4420 5410 --- ---
46, 60, and 76 2180 --- 3880 4210 5280 6340 7740 --- ---
70 and 87 3490 5240 5950 6420 7830 9240 11,110 14,880 18,570
80 4820 --- --- --- 10,490 12,450 14,860 19,340 ---
657 10,880 --- --- 16,400 19,170 21,940 25,630 33,000 40,380
100
667 12,780 --- --- 18,320 21,070 23,840 27,530 34,900 42,280
TRAVEL, INCH
Inch3 0.4375 0.625 0.75 1.125 1.5 2 3 4
Casing Volume(2), Inch3
30 33 56 66 72 --- --- --- --- ---
34 and 40 57 90 104 113 142 170 --- --- ---
45 and 50 95 --- 170 183 227 270 330 --- ---
46, 60, and 76 133 --- 237 257 322 387 472 --- ---
70 and 87 213 320 363 392 478 564 678 980 1133
80 294 --- --- --- 640 760 907 1180 ---
657 664 --- --- 1002 1170 1339 1564 2014 2464
100
667 780 --- --- 1118 1286 1455 1680 2130 2580
1. Clearance volume indicates casing volume at zero travel.
2. Includes clearance volume.
5
Product Bulletin
61.1:657
657 and 667 Actuators August 2009
Table 4. Thrust Capabilities(1) by Input Signal Range Clockwise rotation of the handwheel on the 657
PRESSURE RANGE THRUST actuator moves the actuator stem downward,
TRAVEL ACTUATOR TO ACTUATOR CAPABILITIES compressing the spring. Spring action returns the
SIZE DIAPHRAGM(2) 657 667 stem as the handwheel is turned counterclockwise.
mm Bar N With the 667 actuator, counterclockwise rotation
0.2-1 2250 1840 moves the stem upward, and spring action returns
30
0.4-2 3890 3270 the stem on clockwise rotation.
19
0.2-1 3380 3380
34
0.4-2 5830 5530
0.2-1 3380 2760
40
0.4-2 5530 3680
Side-Mounted Handwheels—Figure 4 shows the
0.2-1 4670 4670
side-mounted handwheels (designated by the letters
29 45
0.4-2 8410 8870
MO) applicable to sizes 34 through 87, 657 and 667
0.2-1 6940 6250 actuators. Size 30 actuators do not have a
46 side-mounted handwheel available.
0.4-2 13,190 11,800
0.2-1 5140 3740
50
0.4-2 8410 7010
38
0.2-1 6940 4860
60 All side-mounted handwheels can be used to stroke
0.4-2 13,190 8330
the valve in either direction at any point in the
0.2-1 7830 7830
70 actuator stem travel. Unlike the top-mounted
0.4-2 18,590 13,700
handwheel, the side-mounted handwheel can be
0.2-1 10,110 11,250
51 80 positioned to limit travel in either direction, but not
0.4-2 18,950 19,680
0.2-1 6850 7830
both at the same time. With the handwheel in the
87
0.4-2 18,590 13,700
neutral position, automatic operation is possible
0.2-1 16,010 8010
throughout full valve travel. In any other position,
76
0.4-2 32,030 36,030 valve travel will be restricted. The handwheel is
100
0.2-1 12,010 --- furnished with a spring-loaded ball detent which
102 prevents vibration from changing the setting.
0.4-2 22,019 28,024
Inch Psig Lb
3-15 506 414
30
6-30 874 736
0.75
3-15 759 759
34
6-30 1311 1242
3-15 759 621 Adjustable Travel Stops
40
6-30 1242 828
3-15 1050 1050 Top-mounted adjustable travel stops are available
1.125 45
6-30 1890 1995 for 657 and 667 Series actuators. They are used to
3-15 1560 1404
46 limit travel in the up, down, or up and down
6-30 2964 2652
directions. Figure 5 illustrates the different
3-15 1155 840
50 constructions. Table 7 locates the different style
6-30 1890 1575
1.5 constructions with actuator type and use.
3-15 1560 1092
60
6-30 2964 1872
3-15 1760 1760
70
6-30 4180 3080
3-15 2272 2528
2 80
6-30 4260 4424
3-15 1540 1760 Other
87
6-30 4180 3080
3-15 3600 1800 Accessories such as transducers, positioners,
3
100
6-30 7200 8100 position transmitters, air relays, volume boosters,
4
3-15 2700 --- switching valves, lockup valves, limit switches, and
6-30 4950 6300 solenoid valves are also available for actuator
1. For Size 76 667 actuators, contact your Emerson Process Management sales
office.
mounting. They are described in separate
2. Consult Fisher 657 and 667 instruction manuals (D100306X012,
D100307X012, D100310X012, and D100311X012) for additional information on
publications. Contact your Emerson Process
maximum pressure limitations. Management sales office for details.
6
Product Bulletin
61.1:657
August 2009 657 and 667 Actuators
W0368-2/IL W0369-2/IL
W0370-1/IL
TOP VIEW
W0370-1/IL
7
Product Bulletin
61.1:657
657 and 667 Actuators August 2009
SECTION A-A
W0371-1/IL W0372-1/IL
Figure 4. Typical Side-Mounted Handwheels for Fisher 657 and 667 Series Actuators
40A38A1211-E
40A8764-E
8
Product Bulletin
61.1:657
August 2009 657 and 667 Actuators
9
Product Bulletin
61.1:657
657 and 667 Actuators August 2009
10
Product Bulletin
61.1:657
August 2009 657 and 667 Actuators
W4917-1/IL
W4273-1/IL
Figure 6. Fisher 646 Electro-Pneumatic Transducer on Figure 8. Fisher 4200 Position Transmitter on
657 Actuator 667 Actuator
W4930/IL
11
Product Bulletin
61.1:657
657 and 667 Actuators August 2009
Table 8. Dimensions
DIMENSION
ACTUATOR SIZE
REFERENCE
30 34 40 45 46 47 50 60 70 76 80 87 100
mm
657, -4 0 25 25 38 38 38 38 38 38 --- --- 38 ---
B
667, -4 38 38 38 38 38 38 38 38 38 38 --- 38 ---
C 289 333 333 406 473 536 406 473 536 473 635 536 729
D 54 54 71 71 71 71 90 90 90 90 127 127 127(2)
657 440 498 548 659 656 --- 722 722 840 --- 1075 938 NOTE 3
657-4 --- --- --- --- --- --- --- --- 994 --- --- 1089 ---
657MO(1) 440 498 548 659 656 --- 722 722 976 --- 1183 1057 NOTE 4
E
667 478 573 594 768 748 --- 784 784 933 881 1257 1003 1857
667-4 --- --- --- --- --- --- --- --- 1070 --- --- 1143 ---
667MO 478 573 594 768 748 --- 784 784 1164 1112 1392 1245 2346
657 121 164 164 202 202 --- 202 202 313 --- 227 313 ---
Hc
667 119 121 137 159 159 --- 159 159 286 159 --- 286 ---
Hs --- 284 286 375 375 --- 378 378 292 222 303 292 401
Jc 171 222 222 222 222 356 222 222 356 356 356 356 ---
Js --- 305 305 356 356 --- 356 356 432 432 432 432 406
657, -4 213 222 272 291 291 395 354 354 406 --- 435 780 451
K
667, -4 194 224 244 310 310 --- 325 325 375 375 432 419 451
657, -4 --- 226 248 306 306 --- 370 370 446 --- 503 527 NOTE 5
M
667, -4 --- 214 248 362 362 --- 378 378 446 446 503 527 2105
657 --- --- --- --- --- --- --- --- --- --- 254 --- ---
657MO --- --- --- --- --- --- --- --- 219 --- 384 219 ---
657-4MO --- --- --- --- --- --- --- --- 219 --- --- 219 ---
N
667 --- --- --- --- --- --- --- --- --- --- 254 --- ---
667MO --- --- --- --- --- --- --- --- 219 219 384 219 ---
667-4MO --- --- --- --- --- --- --- --- 219 --- --- 219 ---
Inches
657, -4 0.00 1.00 1.00 1.50 1.50 1.50 1.50 1.50 1.50 --- --- 1.50 ---
B
667, -4 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 --- 1.50 ---
C 11.38 13.12 13.12 16.00 18.62 21.12 16.00 18.62 21.12 18.62 25.00 21.12 28.69
D 2.125 2.125 2.8125 2.8125 2.8125 2.8125 3.5625 3.5625 3.5625 3.5625 5 5 5(2)
657 17.31 19.62 21.56 25.94 25.81 --- 28.44 28.44 33.06 --- 42.31 36.94 NOTE 3
657-4 --- --- --- --- --- --- --- --- 39.12 --- --- 42.88 ---
657MO 17.31 19.62 21.56 25.94 25.81 --- 28.44 28.44 38.44 --- 46.56 41.62 NOTE 4
E
667 18.81 22.56 23.38 30.25 29.44 --- 30.88 30.88 36.75 34.70 49.50 39.50 73.12
667-4 --- --- --- --- --- --- --- --- 42.12 --- --- 45.00 ---
667MO 18.81 22.56 23.38 30.25 29.44 --- 30.88 30.88 45.81 43.76 54.81 49.00 92.38
657 4.75 6.44 6.44 7.94 7.94 --- 7.94 7.94 12.31 --- 8.94 12.31 ---
Hc
667 4.69 4.75 5.38 6.25 6.25 --- 6.25 6.25 11.25 6.25 --- 11.25 ---
Hs --- 11.19 11.25 14.75 14.75 --- 14.88 14.88 11.50 11.50 11.94 11.50 15.78
Jc 6.75 8.75 8.75 8.75 8.75 14.00 8.75 8.75 14.00 8.75 14.00 14.00 ---
Js --- 12.00 12.00 14.00 14.00 --- 14.00 14.00 17.00 17.00 17.00 17.00 16.00
657, -4 8.38 8.75 10.69 11.44 11.44 15.56 13.94 13.94 16.00 --- 17.12 18.88 17.75
K
667, -4 7.62 8.83 9.62 12.19 12.19 --- 12.81 12.81 14.75 14.75 17.00 16.50 17.75
657, -4 --- 8.88 9.75 12.06 12.06 --- 14.56 14.56 17.56 --- 19.81 20.75 NOTE 5
M
667, -4 --- 8.44 9.75 14.25 14.25 --- 14.88 14.88 17.56 17.56 19.81 20.75 82.88
657 --- --- --- --- --- --- --- --- --- --- 10.00 --- ---
657MO --- --- --- --- --- --- --- --- 8.62 --- 15.12 8.62 ---
657-4MO --- --- --- --- --- --- --- --- 8.62 --- --- 8.62 ---
N
667 --- --- --- --- --- --- --- --- --- --- 10.00 --- ---
667MO --- --- --- --- --- --- --- --- 8.62 8.62 15.12 8.62 ---
667-4MO --- --- --- --- --- --- --- --- 8.62 --- --- 8.62 ---
1. MO = Manual operator.
2. Also available with 7 inch boss.
3. With group 1 springs, E=1959 mm (77.12 inch). With group 2 springs, E=1497 mm (58.94 inch).
4. With group 1 springs, E=2345 mm (92.31 inch). With group 2 springs, E=1883 mm (74.12 inch).
5. With group 1 springs, M=2103 mm (82.81 inch). With group 2 springs, M=1654 mm (65.12 inch).
12
Product Bulletin
61.1:657
August 2009 657 and 667 Actuators
AU6713-D/DOC AU6713-D/DOC
A0171-2/DOC
40A8196/DOC
13
Product Bulletin
61.1:657
657 and 667 Actuators August 2009
Specifications
Standard Operating Pressure Range(1) Signal Connections
657 and 667: J0.2 to 1.0 bar (3 to 15 psig) or Sizes 30 - 60 and 667 Size 76: 1/4 NPT internal
J0.4 to 2.0 bar (6 to 30 psig) Sizes 70 and 87: 1/2 NPT internal
657-4 and 667-4: 0.2 to 1.9 bar (3 to 27 psig) Size 80
667 Size 76: J0.4 to 2.0 bar (6 to 30 psig) or J0 657: 3/4 NPT internal with 1/4 NPT internal
to 3.1 bar (0 to 45 psig) bushing
667: 1/2 NPT internal with 1/4 NPT internal
bushing
Maximum Travel Size 100: 1 NPT internal with 1/4 NPT internal
bushing
See table 1
Effective Diaphragm Area
Output Indication See table 1
Stainless steel disk or pointer and graduated
scale Construction Materials (refer to figure 2)
Diaphragm Casing
Sizes 30 - 87: Steel
Stroking Speed Size 80: JCast iron or Jsteel
Dependent on actuator size, travel, spring rate, Size 100: JCast aluminum
initial spring compression, and supply pressure. If Diaphragm
stroking speed is critical, consult your Emerson Sizes 30 - 87: JNitrile on nylon, JSilicone on
Process Management sales office polyester
Size 100: Nitrile on polyester
Diaphragm Plate
Maximum Allowable Thrust(2) 657 Sizes 30- 60, 100: JCast aluminum
657 Sizes 70 - 87: JCast iron or Jsteel
See table 1
667 Sizes 30 - 60, 100: JCast aluminum or
Jsteel
Operating Temperature Range(1) 667 Sizes 70 - 87: JCast iron or Jsteel
Actuator Spring: Steel
Standard Construction (Nitrile Elastomers): Spring Adjustor: Steel
-40 to 82_C (-40 to 180_F) Spring Seat: JSteel or Jcast iron
Optional Construction (Silicone Diaphragm): Actuator Stem: Steel
-40 to 149C (-40 to 300F) Travel Indicator: Stainless steel
Maximum Valve Packing Box Temperature: O-Rings: Nitrile
427_C (800_F) with cast iron yoke Seal Bushing: Brass
Stem Connector: Zinc-plated steel
Volumetric Displacement Yoke
Sizes 30 - 80: J Cast iron or J steel
See table 2 Size 100: Steel
- continued -
14
Product Bulletin
61.1:657
August 2009 657 and 667 Actuators
Specifications (continued)
Construction Materials for Cold Service Approximate Weight
[to -50_C (-58_F)] 657 and 667--all sizes
Yoke: Steel (Grade LCC) See table 3
Diaphragm: Silicone
O-Rings:(3) Ethylene Propylene
Bolting: Stainless Steel B8M Cl 2 Options
Stem Connector: Stainless Steel
Lubricant: Silicone JOversize signal connections, JPlastic yoke
covers, JWatertight yoke (sealed construction
Stem and Yoke Boss Diameters for certain applications where valve stem and
See table 1 packing must be protected)
1. The pressure and temperature limits in this bulletin and in any applicable standard or code limitation should not be exceeded.
2. Do not exceed the thrust limits in this bulletin.
3. Includes diaphragm casing seals, casing-mounted handjack on 657, seal bushing on 667.
Note
Neither Emerson, Emerson Process
Management, nor any of their affiliated
entities assumes responsibility for the
selection, use, or maintenance of any
product. Responsibility for the
selection, use, and maintenance of any
product remains with the purchaser
and end-user.
15
Product Bulletin
61.1:657
657 and 667 Actuators August 2009
Fisher and easy-e are marks owned by one of the companies in the Emerson Process Management business division of Emerson Electric Co.
Emerson Process Management, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are
the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they
are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or
applicability. All sales are governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the
designs or specifications of such products at any time without notice. Neither Emerson, Emerson Process Management, nor any of their affiliated
entities assumes responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use, and maintenance of
any product remains solely with the purchaser and end-user.
EFisher
16 Controls International LLC 1990, 2009; All Rights Reserved
Bulletin 71.1:67C
March 2004
✰ No Air Loss
✰ Easy Maintenance
✰ Rugged Construction
A 67C Series instrument
supply regulator
W8438
W7423_1
D102656X012
www.FISHERregulators.com
Bulletin 71.1:67C
Introduction
The 67C Series regulators are typically used to provide constantly controlled, reduced pressures to pneumatic and
electropneumatic controllers and other instruments. These direct-operated regulators are suitable for most air or
gas applications. Other applications include providing reduced pressures to air chucks, air jets, and spray guns.
2
Bulletin 71.1:67C
Specifications
Body Size, Inlet and Outlets Connection Style Smart Bleed™ Check Valve Setpoint
1/4-inch NPT 6 psi (0,4 bar) differential
Construction Materials Pressure Registration
See Table 2 Internal
(1)
Maximum Inlet Pressure (Body Rating) Drain Valve and Spring Case Vent Location
All except 67CS and 67CSR: 250 psig (17,2 bar) Aligned with inlet standard, other positions optional
Type 67CS and 67CSR: 400 psig (27,6 bar)
Regulator Temperature Capabilities
Outlet Pressure Ranges
With Nitrile (NBR)
See Table 1
Standard Bolting: -20 to 180°F (-29 to 82°C)
Maximum Emergency Outlet Pressure(1) Stainless Steel Bolting: -40 to 180°F (-40 to 82°C)
50 psi (3,4 bar) over outlet pressure setting With Fluoroelastomer (FKM):
0 to 300°F (-18 to 149°C)
Capacities
With Silicone (VMQ)(3) Diaphragm and Low
See Table 3 and Capacity Information section Temperature bolting: -60 to 180°F (-51 to 82°C)
Wide-Open Flow Coefficients With Gauges: -20 to 180°F (-29 to 82°C)
Main Valve: Cg: 11.7; Cv: 0.36; C1: 32.2; Type 67CF, 67CFR, 67CFS, and 67CFSR Filter
Internal Relief Valve: Cg: 1.45; Cv: 0.045; C1: 32.8 Capabilities
IEC Sizing Cooefficients Free Area: 12 times pipe area
Main Valve: XT: 0.66; FL: 0.89; FD: 0.50 Micron Rating: Cellulose Element: 40 microns
Glass Fiber Element: 5 microns
Accuracy Stainless Steel Element: 40 microns
Inlet Sensitivity: Less than 0.2 psig (0,014 bar)
Options
change in outlet pressure for every 25 psig
(1,72 bar) change in inlet pressure All Types
Repeatability: 0.1 psig (0,0069 bar)(2) • Handwheel adjusting screw
• Inlet screen
Air Consumption: testing repeatedly shows
• NACE MR0175(4) or NACE MR0103 construction
no discernible leakage
• Panel mount (includes spring case with 1/4-inch
Type 67CR, 67CSR, 67CFR, and 67CFSR Internal vent, handwheel, and panel mounting nut)
Relief Performance • Closing cap (available on spring case with
Low capacity for minor seat leakage only; other 1/4-inch NPT vent)
overpressure protection must be provided if inlet • Fluoroelastomer (FKM) elastomers for high
pressure can exceed the maximum pressure rating temperatures and/or corrosive chemicals
of downstream equipment or exceeds maximum • Silicone (VMQ) elastomers for cold temperatures
outlet pressure rating of the regulator. • Fixed Bleed Restriction
• Triple scale outlet pressure gauge (brass or
Approximate Unit Weight stainless steel)
Types 67C, 67CR, 67CF, and 67CFR: • Stainless steel stem on the valve plug
1 pound (0,5 kg) • Tire valve or pipe plug in second outlet
Types 67CS and 67CSR: Type 67CFR only
2.5 pounds (1,2 kg) • Smart Bleed™ internal check valve
Types 67CFS and 67CFSR: Types 67CF and 67CFR only
4 pounds (1,8 kg) • Stainless steel drain valve
1. The pressure/temperature limits in this bulletin and any applicable standard or code limitation should not be exceeded.
2. Repeatability is the measure of the regulator's ability to return to setpoint consistently when traveling from steady state to transient to steady state.
3. Silicone is not compatible with hydrocarbon gas.
4. Product complies with the material requirements of NACE MR0175. Environmental limits may apply.
3
Bulletin 71.1:67C
OUTLET PRESSURE
ATMOSPHERIC PRESSURE TYPE 67CFR OR 67CFSR SMART BLEED™ OPTION
TYPE 67CFR ONLY
Figure 2. 67C Series Operational Schematics
4
Bulletin 71.1:67C
Principle of Operation (figure 2) leakage only. Other overpressure protection must be
provided if the maximum inlet pressure can exceed the
Downstream pressure is registered internally on the maximum pressure rating of the downstream equipment
lower side of the diaphragm. When the downstream or exceeds maximum outlet pressure rating of the
pressure is at or above the set pressure, the valve plug Type 67CR, 67CSR, 67CFR, or 67CFSR regulator.
is held against the orifice and there is no flow through
the regulator. When demand increases, downstream
pressure drops slightly allowing the spring to extend,
Capacity Information
moving the stem down and the valve plug away from Table 3 shows the air regulating capacities of the
the orifice. This allows flow through the regulator. 67C Series regulators at selected inlet pressures and
outlet pressure settings. Flows are shown in scfh
Internal Relief (Types 67CR, 67CSR, (at 60°F and 14.7 psia) and in m³/h(n) (at 0°C and
1,01325 bar) of air.
67CFR, and 67CFSR)
If for some reason, outside of normal operating Note
conditions, the downstream pressure exceeds the set The 67C Series regulators may be sized
point of the regulator, the force created by the for 100% flow using capacities as shown
downstream pressure will lift the diaphragm until the in table 3. It is not necessary to reduce
diaphragm is lifted off the relief seat. This allows flow published capacities.
through the token relief. The relief valve on the
Type 67CR, 67CSR, 67CFR, or 67CFSR is an elastomer To determine the equivalent capacities for other gases,
plug that prevents leakage of air from the downstream multiply the table capacity by the following appropriate
to atmosphere during normal operation, thereby conversion factor: 1.29 for 0.6 specific gravity natural
conserving plant air. gas, 0.810 for propane, 0.707 for butane, or 1.018 for
nitrogen. For gases of other specific gravities, divide
Smart Bleed™ Airset the table capacities by the square root of the appropri-
ate specific gravity. To find wide-open flow capacities
In some cases, it is desired to exhaust downstream
for relief sizing at any inlet pressure, perform one of
pressure if inlet pressure is lost or drops below the
the following procedures. Then, if necessary, convert
setpoint of the regulator. For example, if the regulator is
using the factors provided above.
installed on equipment that at times has no flow
demand but is expected to backflow on loss of inlet For critical pressure drops (absolute outlet pressure
pressure. The Type 67CFR can be ordered with the equal to or less than one-half of absolute inlet pres-
Smart Bleed™ option which includes an internal check sure), use the following formula:
valve for this application. During operation, if inlet
Q = (P1)(Cg)
pressure is lost, or decreases below the setpoint of the
regulator, the downstream pressure will back flow
For pressure drops lower than critical (absolute
upstream through the regulator and check valve. This
outlet pressure greater than one-half of absolute inlet
option eliminates the need for a fixed bleed downstream
pressure), use the following formula:
of the regulator, thereby conserving plant air.
520 ⎛ 3417 ∆P ⎞
Q= CgP1SIN ⎜⎜ ⎟ DEG
Overpressure Protection GT ⎝ C1 P1 ⎟⎠
The 67C Series regulators have maximum outlet where,
pressure ratings that are lower than their maximum
Q = gas flow rate, scfh
inlet pressure ratings. A pressure relieving or pressure
P1 = absolute inlet pressure, psia (P1 gauge + 14.7)
limiting device is needed if inlet pressure can exceed
the maximum outlet pressure rating. Refer to the Cg = gas sizing coefficient
Capacity Information section and the Wide-Open G = specific gravity of the gas
Coefficients for Relief Valve Sizing in the Specifica- T = absolute temperature of gas at inlet, °Rankine
tions on page 3 to determine the required relief valve C1 = flow coefficient (Cg ÷ Cv)
capacity. ∆P = pressure drop across the regulator, psi
Type 67CR, 67CSR, 67CFR, and 67CFSR regulators Then, if capacity is desired in normal cubic meters per
have a low capacity internal relief valve for minor seat hour (at 0°C and 1,01325 bar), multiply scfh by 0.0268.
5
Bulletin 71.1:67C
Table 3. Capacities
=OUTLET PRESSURE CAPACITIES IN SCFH (m3/h(n)) OF AIR
OUTLET
RANGE, SPRING PART INLET PRESSURE,
PRESSURE, Types 67C, 67CR, 67CS, and 67CSR Types 67CF, 67CFR, 67CFS, and 67CFSR
NUMBER AND COLOR, PSIG (bar)
PSIG (bar)
PSIG (bar) 10% Droop 20% Droop 10% Droop 20% Droop
50 (3,4) 250 (6,70) 430 (11,5) 250 (6,70) 430 (11,5)
75 (5,2) 340 (9,11) 610 (16,3) 300 (8,04) 690 (18,5)
100 (6,9) 430 (11,5) 800 (21,4) 330 (8,84) 1000 (26,8)
15 (1,0)
150 (10,3) 680 (18,2) 1200 (32,2) 400 (10,7) 1600 (42,9)
250 (17,2) 1300 (34,8) 1900 (50,9) 450 (12,1) 1800 (48,2)
400 (27,6)(2) 390 (10,5) 1850 (50,0) -- -- -- --
50 (3,4) 310 (8,31) 460 (12,3) 350 (9,38) 500 (13,4)
0 to 35 (0 to 2,4) 75 (5,2) 420 (11,3) 700 (18,8) 530 (14,2) 820 (22,0)
T14059T0012 (Silver) 100 (6,9) 620 (16,6) 940 (25,2) 750 (20,1) 1100 (29,5)
20 (1,4)
T14113T0012 150 (10,3) 960 (25,7) 1450 (38,9) 1400 (37,5) 1600 (42,9)
(Silver Stripe) 250 (17,2) 1550 (41,5) 2150 (57,6) 2550 (68,3) 2700 (72,3)
400 (27,6)(2) 1200 (32,2) 2750 (73,7) -- -- -- --
50 (3,4) 390 (10,5) 490 (13,1) 390 (10,5) 500 (13,4)
75 (5,2) 590 (15,8) 850 (22,8) 640 (17,1) 820 (22,0)
100 (6,9) 770 (20,6) 1150 (30,8) 840 (22,5) 1100 (29,5)
35 (2,4)
150 (10,3) 1200 (32,2) 1750 (46,9) 1450 (38,9) 1650 (44,2)
250 (17,2) 2200 (58,9) 2700 (72,3) 2450 (65,6) 2700 (72,3)
400 (27,6)(2) 2850 (76,4) 3450 (92,5) -- -- -- --
50 (3,4) 310 (8,31) 440 (11,8) 330 (8,84) 470 (12,6)
75 (5,2) 440 (11,8) 670 (18,0) 500 (13,4) 730 (19,6)
100 (6,9) 560 (15,0) 900 (24,1) 700 (18,8) 1000 (26,8)
35 (2,4)
150 (10,3) 780 (20,9) 1350 (36,2) 1050 (28,1) 1550 (41,5)
0 to 60 (0 to 4,1) 250 (17,2) 1450 (38,9) 2200 (59,0) 2000 (53,6) 2600 (69,7)
T14058T0012 400 (27,6)(2) 770 (20,6) 2500 (67,0) -- -- -- --
(Blue stripe)
T14114T0012 (Blue) 75 (5,2) 520 (13,9) 720 (19,3) 520 (13,9) 720 (19,3)
100 (6,9) 750 (20,1) 1050 (28,1) 770 (20,6) 1000 (26,8)
60 (4,1) 150 (10,3) 1100 (29,5) 1700 (45,6) 1100 (29,5) 1600 (42,9)
250 (17,2) 2050 (54,9) 2850 (76,4) 2450 (65,6) 2750 (73,7)
400 (27,6)(2) 3200 (85,8) 4300 (115) -- -- -- --
100 (6,9) 500 (13,4) 800 (21,4) 530 (14,2) 780 (20,9)
150 (10,3) 750 (20,1) 1200 (32,2) 780 (20,9) 1200 (32,2)
0 to 125 (0 to 8,6) 80 (5,5)
250 (17,2) 1200 (32,2) 2050 (54,9) 1250 (33,5) 2200 (58,9)
T14060T0012 400 (27,6)(2) 910 (24,4) 3700 (99,2) -- -- -- --
(Red stripe)
T14115T0012 (Red) 150 (10,3) 900 (24,1) 1250 (33,5) 900 (24,1) 1150 (30,8)
125 (8,6) 250 (17,2) 1560 (41,8) 2450 (65,6) 1650 (44,2) 2450 (65,6)
400 (27,6)(2) 2200 (59,0) 4350 (117) -- -- -- --
250 (17,2) 550 (14,7) 1200 (32,2) 550 (14,7) 1200 (32,2)
80 (5,5)
400 (27,6)(2) 400 (10,7) 1100 (29,5) -- -- -- --
0 to 150 (0 to 8,6)(1) 250 (17,2) 970 (26,0) 1800 (48,2) 1100 (29,5) 1800 (48,2)
135 (9,3)
10C1730X012 (Black) 400 (27,6)(2) 840 (22,5) 2350 (63,0) -- -- -- --
250 (17,2) 1100 (29,5) 1850 (49,6) 1100 (29,5) 1850 (49,6)
150 (10,3)
400 (27,6)(2) 940 (25,2) 2500 (67,0) -- -- -- --
1. Available for Types 67CS, 67CSR, 67CFS and 67CFSR only
2. Inlet pressures above 250 psig (17,2 bar) with a maximum of 400 psig (27,6 bar) only available on Types 67CS and 67CSR.
670 Series Panel-Mounted Loading connected to one or two gauges and a changeover
valve. A single gauge typically shows loading
Regulators (figure 4) pressure to the control valve. For more information
see bulletin 62.3:670.
The 670 Series panel-mounted loading regulators are
compact, rugged units used primarily for manually
loading pressure-balanced gas regulators and providing
manual control for diaphragm actuator control valves. Ordering Information
Applications include remote control of gas pressure to
burners in refineries, power plants, and various When ordering, complete the Ordering Guide on page
process furnaces. 12. Refer to the Specifications on page 3. Review the
description to the right of each specification and the
Three basic panels are available within the product information in each referenced table or figure. Specify
line, each having one 67C Series pressure regulator your choice whenever a selection is offered.
6
Bulletin 71.1:67C
67C SERIES
FILTER REGULATOR
UPSTREAM PRESSURE
LOADING PRESSURE
W7434
DOWNSTREAM PRESSURE TYPE 92P
STEAM REGULATOR
A 67C SERIES PRESSURE LOADING REGULATOR USED WITH THE TYPE 92P STEAM REGULATOR ELIMINATES THE NEED FOR A
PILOT REGULATOR. THIS PROVIDES HIGH ACCURACY AND IMPROVED PERFORMANCE IN DIRTY STEAM SERVICE.
Figure 3. 67C Series Regulator Used to Pressure Load a 92P Steam Regulator
7
Bulletin 71.1:67C
4.56 2.56
(116) (65)
2.92 0.50
(74) (13)
1.46
(37)
A
MAX
OUTLET
OPTIONAL GAUGE
CONNECTIONS
1/4-INCH NPT
INLET CONNECTION
1/4-INCH NPT
STANDARD DIMENSIONS
SIDE OUTLET
STANDARD DIMENSIONS
1/4-INCH NPT
FOR GAUGE OPTION 2.56
(65)
INCHES
(mm)
4.56 1.43
(116) (36)
CLOSING CAP
2.92
(74)
1.46
(37)
D OUTLET
CONNECTIONS
C OPTIONAL GAUGE 1/4-INCH NPT
INLET CONNECTION
1/4-INCH NPT
DIMENSIONS FOR PANEL MOUNT OPTION WITH DIMENSIONS WITH CLOSING CAP
HAND WHEEL AND 1/4-INCH SPRING CASE VENT AND 1/4-INCH SPRING CASE VENT
DIMENSION WITH
STANDARD DIMENSIONS PANEL MOUNT OPTION WITH HANDWHEEL DIMENSIONS
TYPE CLOSING CAP
A B A A C D
67C , 67C R 3.50 (89) 1.51 (38) 4.60 (117) 4.69 (119) 1.08 (27) 2.33 (59)
67C S , 67C S R 4.13 (105) 1.62 (41) 4.93 (125) 5.00 (127) 1.14 (29) 2.65 (67)
8
Bulletin 71.1:67C
4.56
(116) 2.56
3.00
(65)
(76)
1.48 0.62
(38) (16)
3.50
(89)
MOUNTING HOLES
3.50 FOR 5/16-INCH
(89) DIAMETER BOLTS
SIDE OUTLET
1/4-INCH NPT
2.25
(57)
DRAIN VALVE
GAUGE
DRAIN VALVE
VENT POSITION 1 POSITION 1 DRAIN VALVE
VENT POSITION 3 POSITION 3
(STANDARD) (STANDARD)
INLET OUTLET
INLET OUTLET
GAUGE
VENT POSITION 4
DRAIN VALVE
POSITION 2
B2699_D
B2699_C
9
Bulletin 71.1:67C
4.56 2.56
(116) (65)
3.00
(76) 1.43
(36) CLOSING CAP
2.37
(60) 1.48
MAX PANEL (38)
0.12 TO 0.25 0.72-INCH (1,8 mm)
(3,0 TO 6,5) SPRING CASE
PANEL BOSS
4.78
4.69
(121)
(119)
MAX
1/4-INCH NPT VENT
2.41
(61)
1.14 INLET CONNECTION OUTLET
(29) 1/4-INCH NPT CONNECTIONS
1/4-INCH NPT
0.69
OPTIONAL GAUGE (18)
MOUNTING HOLES
3.50 FOR 5/16-INCH
(89) DIAMETER BOLTS
2.25
(57)
B2700_A
INCHES 2.87
(mm) (73)
B2700_B
SPACER
(FOR INSTALLING A 67CF SERIES
REGULATOR IN AN EXISTING
0.18
INSTALLATION IF THE MOUNTING
(4,57)
BOLTS ARE TOO LONG)
0.50 OD 0.32
(12.7) ID
(8.12)
B2697_B
B2697_A
10
Bulletin 71.1:67C
4.56 1.43
(116) (36)
3.00 2.56
(76) (65)
1.48 0.62 CLOSING
(38) (16) CAP
4.93
(125)
0.69
(18)
1/4-INCH NPT
INLET CONNECTION
2.25
(57)
INCHES 2.87
(mm) (73)
STANDARD DIMENSIONS (INCLUDING CLOSING CAP) STANDARD DIMENSIONS (INCLUDING CLOSING CAP)
2.37
(60)
MAX
5.00
(127)
4.13
MAXIMUM
(105)
MAXIMUM PANEL
0.12-0.25 2.65
(3-6,5) (67)
INCHES
(mm)
DIMENSIONS WITHOUT CLOSING CAP DIMENSIONS FOR PANEL MOUNT OPTION WITH HANDWHEEL
11
Bulletin 71.1:67C
Ordering Guide Spring Case Vent Location (Select One)
Position 1 - Aligned with inlet (standard)***
Type (Select One) Position 2
Type 67C (aluminum without internal relief)*** Position 3
Type 67CR (aluminum with internal relief)*** Position 4
Type 67CS (stainless steel without internal relief)*** Fixed Bleed for Type 67CR, 67CSR, 67CFR, or 67CFSR (Optional)
Type 67CSR (stainless steel with internal relief)*** Yes**
Type 67CF (aluminum with filter and without internal relief)***
Type 67CFR (aluminum with filter and internal relief)*** Smart Bleed™ Internal Check Valve Airset (Optional - 67CFR only)
Type 67CFS (stainless steel with filter and without Yes**
internal relief)*** Second Outlet (Select One)
Type 67CFSR (stainless steel with filter and internal relief)*** Open (67C, 67CR, 67CF, 67CFR standard)***
Plugged with pipe plug (67CS, 67CSR, 67CFS, 67CFSR
Quantity (Specify)
standard)***
Spring Case Style (Select One) Tire Valve***
Drilled hole vent (67C, 67CR, 67CF, 67CFR standard)*** Pressure Gauge (see below)
1/4-inch NPT vent (67CS, 67CSR, 67CFS, 67CFSR standard)*** Triple Scale Pressure Gauge (Optional)
Single hole panel mount***
Brass Gauge or Stainless Steel Gauge
Adjusting Screw (Select One) 0 to 30 psig/0 to 0.2 MPa/0 to 2 bar***
Square head (67C, 67CR, 67CF, 67CFR standard)*** 0 to 60 psig/0 to 0.4 MPa/0 to 4 bar***
Square head with closing cap (67CS, 67CSR, 67CFS, 0 to 160 psig/0 to 1.1 MPa/0 to 11 bar***
67CFSR standard)*** NACE MR0175 Construction (Optional)(1)
Handwheel*** Yes (not available with gauge)**
Outlet Pressure Range (Select One) 1. Product complies with the material requirements of NACE MR0175.
0 to 20 psig (0 to 1,4 bar)*** Environmental limits may apply.
0 to 35 psig (0 to 2,4 bar)*** NACE MR0103 Construction (Optional)
0 to 60 psig (0 to 4,1 bar)*** Yes (not available with gauge)**
0 to 125 psig (0 to 8,6 bar)***
0 to 150 psig (0 to 10,3 bar) (67CS, 67CSR, 67CFS, 67CFSR Replacement Parts Kit (Optional)
only)*** Yes, send one replacement parts kit to match this order.
Diaphragm, O-Rings, and Valve Plug (Select One)
Nitrile (NBR) (standard)***
Fluoroelastomer (FKM)**
Silicone (VMQ) diaphragm, O-rings, and nitrile valve plug*
Filter Material (Select One)
Cellulose (40 microns)(67CF, 67CFR standard)***
Glass (5 microns)*** Specification Worksheet
Stainless steel (40 microns)(67CFS, 67CFSR standard)*** Application (Please designate units):
Drain Valve (Select One) Specific Use
Brass (67CF, 67CFR standard)*** Line Size
Stainless steel (67CFS, 67CFSR standard)*** Gas Type and Specific Gravity
Drain Valve Location (Select One) Gas Temperature
Position 1 - Aligned with inlet (standard)*** Does the Application Require Overpressure Protection?
Position 2 No Yes, if so, which is preferred:
Position 3 Relief Valve Monitor Regulator Shutoff Device
Position 4 Is overpressure protection equipment selection assistance
desired?
Pressure (Please designate units):
Maximum Inlet Pressure (P1max)
Fisher Regulators Quick Order Guide Minimum Inlet Pressure (P1min)
Downstream Pressure Setting(s) (P2)
*** Standard - Readily Available for Shipment Maximum Flow (Qmax)
** Non-Standard - Allow Additional Time for Shipment Performance Required:
Accuracy Requirements?
Special Order, Constructed from Non-Stocked Parts. Need for Extremely Fast Response?
*
Consult Your Fisher Sales Representative for Availability. Other Requirements:
Availability of the product being ordered is determined by the component
with the longest shipping time for the requested construction.
Fisher is a mark owned by Fisher Controls International, Inc., a business of Emerson Process Management. The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the
property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express
or implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or specifications of such products at any time without notice.
Fisher does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any Fisher product remains solely with the purchaser.
©Fisher Controls International, Inc., 2001, 2004; All Rights Reserved www.FISHERregulators.com
Product Bulletin
62.1:DVC6000(S1)
D103308X012
February 2009 FIELDVUE Digital Valve Controllers
www.Fisher.com
Product Bulletin
62.1:DVC6000(S1)
FIELDVUE Digital Valve Controllers February 2009
189.1
(7.44)
28.6 122.8
(1.13) (4.84)
2 MOUNTING HOLES
j 8.6 (0.34)
FEEDBACK
ARM
144.5
(5.69)
1/4−18 NPT
ACTUATOR OUTPUT CONN
CENTERLINE PLUGGED
1/2−14 NPT
148.7
CONDUIT CONN
(5.85)
BOTH SIDES
1/4−18 NPT
OUTPUT CONN A
FISHER 67CFR
1/4−18 NPT
SUPPLY CONN
210.7
(8.29)
3/8−18 NPT
VENT CONN
1/4−18 NPT
OUTPUT CONN B
201.8 mm
48B7710 Sht 1 / Doc. (7.94) (INCH)
19B3538−C
E0405−2 / IL
Figure 1. FIELDVUE DVC6010 / DVC6010 SIS / DVC6010f Digital Valve Controller with Integrally Mounted Filter Regulator
2
Product Bulletin
62.1:DVC6000(S1)
February 2009 FIELDVUE Digital Valve Controllers
MOUNTING
BRACKET
FEEDBACK
ARM
156.3
(6.16)
1/2−14 NPT
CONDUIT CONN
BOTH SIDES
1/4−18 NPT
OUTPUT
CONN A
FISHER 67CFR
1/4−18 NPT
SUPPLY CONN
234.7
(9.24)
95.3
(3.75)
157.7
(6.21)
1/4−18 NPT
OUTPUT CONN B
201.8
4 MOUNTING
(7.94)
HOLES
j 9.7 (0.38)
174.6
(6.88)
1/4−18 NPT
OUTPUT CONN
ACTUATOR PLUGGED
CENTERLINE 91.5 mm
(3.6) (INCH)
Figure 2. FIELDVUE DVC6020 / DVC6020 SIS / DVC6020f Digital Valve Controller with Integrally Mounted Filter Regulator
3
Product Bulletin
62.1:DVC6000(S1)
FIELDVUE Digital Valve Controllers February 2009
FEEDBACK
ARM
125
(4.91) 1/2−14 NPT
CONDUIT CONN
BOTH SIDES
1/4−18 NPT
OUTPUT CONN A
FISHER 67CFR
1/4−18 NPT
210.7 SUPPLY CONN
(8.29)
3/8−18 NPT
VENT CONN
1/4−18 NPT
148.1 OUTPUT
(5.83) CONN
PLUGGED mm
214.7
(INCH)
(8.45)
Figure 3. FIELDVUE DVC6030 / DVC6030 SIS / DVC6030f Digital Valve Controller with Integrally Mounted Filter Regulator
4
Product Bulletin
62.1:DVC6000(S1)
February 2009 FIELDVUE Digital Valve Controllers
63 193
(2.46) (7.60)
92
(3.62)
234
(9.20)
1/4 −18 NPT
SUPPLY CONN
211
(8.29)
1/4−18 NPT
OUTPUT CONN B
10C1795−A / DOC
10C1796−A / DOC 3/8 −18 NPT mm
E1102
VENT CONN (INCH)
Figure 4. FIELDVUE DVC6005 / DVC6005 SIS / DVC6005f Base Unit; Pipestand Mounted
5
Product Bulletin
62.1:DVC6000(S1)
FIELDVUE Digital Valve Controllers February 2009
64
(2.50)
57
(2.25)
BRACKET LOCATION
FOR WALL MOUNTING
184
(7.23) 72
(2.82)
2 MOUNTING mm
10C1795−A / DOC HOLES 0.86 (0.34) (INCH)
10C1796−A / DOC
E1103
Figure 5. FIELDVUE DVC6005 / DVC6005 SIS / DVC6005f Base Unit; Wall Mounted
57
(2.25)
29
(1.13)
2 MOUNTING 97
HOLES CENTERLINE OF (3.81)
8.6 (0.34) ACTUATOR
19
(0.76)
138
(5.45)
121
(4.75)
1/2−14 NPT
CONDUIT CONN
65
(2.54)
175
(6.89) mm
(INCH)
10C1797−A
E0867−2 / IL
Figure 6. FIELDVUE DVC6015 Feedback Unit; Sliding−Stem Actuator Mounting up to 102 mm (4 inch) Travel
6
Product Bulletin
62.1:DVC6000(S1)
February 2009 FIELDVUE Digital Valve Controllers
9
(0.37)
4 MOUNTING
HOLES
9.7 (0.38)
175
94 (6.88)
(7.63)
1/2−14 NPT
CONDUIT
CONN
99
(3.90) 95
10
(0.38) (3.75)
10C1798−A
E0868−2 / IL
114
(4.50)
140
(5.52) mm
(INCH)
Figure 7. FIELDVUE DVC6025 Feedback Unit; Rotary and Long−Stroke Sliding−Stem Actuator Mounting
76
(3.00)
38
(1.50)
46
(1.83)
120 93
(4.72) (3.66)
4 MOUNTING
HOLES
103 1/2−14 NPT 67 46 1/4−20 UNC
(2.65) CONDUIT (2.65) (1.81)
CONN
135
mm
(4.07)
(INCH)
10C1799−A
E0869 / IL
7
Product Bulletin
62.1:DVC6000(S1)
FIELDVUE Digital Valve Controllers February 2009
Fisher and FIELDVUE are marks owned by one of the companies in the Emerson Process Management business division of Emerson Electric Co.
Emerson Process Management, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. HART is a mark
owned by the HART Communication Foundation. FOUNDATION fieldbus is a mark owned by the Fieldbus Foundation. All other marks are the
property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they
are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or
applicability. All sales are governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the
designs or specifications of such products at any time without notice. Neither Emerson, Emerson Process Management, nor any of their affiliated
entities assumes responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use, and maintenance of
any product remains solely with the purchaser and end−user.
EFisher
8 Controls International LLC 2008, 2009; All Rights Reserved
Product Bulletin
51.1:ED
D100017X012
June 2010 ED Valve
www.Fisher.com
Product Bulletin
51.1:ED
ED Valve June 2010
2
Product Bulletin
51.1:ED
June 2010 ED Valve
CAGE GASKET
SHIM
DOUBLE
PISTON RINGS
(SMALLER SIZES
LOAD
HAVE TRIPLE
BONNET RING
PISTON RINGS)
GASKET
RESTRICTED
SPIRAL TRIM
WOUND ADAPTORS
GASKET
W09774 / IL
RESTRICTED TRIM
W33621 / IL
STEM
PTFE V-RING
PACKING
BONNET GASKET
BALANCING PORT
SHIM
GRAPHITE PISTON RING
CAGE
SPIRAL
WOUND GASKET
VALVE PLUG
PIN
SEAT RING
GASKET
SEAT RING
W04514 / IL
3
Product Bulletin
51.1:ED
ED Valve June 2010
OPTIONAL LINER
W09695 / IL
W20025 / IL
W6980 / IL
WhisperFlo TRIM
W6851-1 / IL
4
Product Bulletin
51.1:ED
June 2010 ED Valve
Table 1. C-seal Shutoff Classification
VALVE VALVE SIZE PORT DIAMETER ANSI/FCI LEAKAGE
CAGE STYLE
(PRESSURE RATING) NPS mm Inches CLASS
2-1/2 73 2.875 Eq. %, Linear,
Whisper I, Cav III, 1
3 87.3 3.4375 stage
3 73 2.875
Cav III, 2 stage
4 73 2.875
Eq. %, Linear,
73 2.875
4 Whisper I, Cav III, 1 V to 593_C (1100_F)
111.1 4.375
stage [for port diameters
ED Whisper III (A3, B3, from 73 through 203.2
(CL150-600) 136.5 5.375 C3, D3), Cav III, 2 mm (2.875 through
stage 8-inch) with optional
6 C-seal trim]
Eq. %, Linear,
177.8 7 Whisper I, Cav III, 1
stage
177.8 7 Cav III, 2 stage
8 Eq. %, Linear,
203.2 8 Whisper I, Cav III, 1
stage
STAKE THREAD
FLOW DOWN
PISTON
RING
RETAINER
C-SEAL
METAL
PLUG
SEAL(1) VALVE PLUG
FLOW UP
C-SEAL
NOTES: METAL
1. REVERSE THE ORIENTATION OF THE C-SEAL PLUG SEAL PLUG
FOR PROPER SHUTOFF WHEN VALVE IS USED IN A PROCESS SEAL(1)
WITH DIFFERENT FLUID FLOW DIRECTION.
A6869 / IL
5
Product Bulletin
51.1:ED
ED Valve June 2010
6
Product Bulletin
51.1:ED
June 2010 ED Valve
Table 3. Typical Combinations of Metal Trim Parts(1) for all Valves Except Those for NACE Specification, Whisper Trim III, and
WhisperFlo Cages
Liner
Trim Designation Valve Plug Cage Seat Ring
(EAD Valve Only)
1 (standard for ED, EAD,
S41600 HT or
and EDR in all valve body materials S41600 HT CB7Cu-1 HT S41600 HT
CA15 HT(2)
except CF8M)
S31600
3 and 3H(3) with seat and guide hard faced with R30006 (alloy 6) R30006 (alloy 6) ---
CoCr-A hardfacing alloy
4(4) S31600 CB7Cu-1 HT S31600 S31600
S31600 with seat and guide
27 CF8M
hard faced with CoCr-A hardfacing alloy
with electroless R30006 (alloy 6) ---
S31600 with seat hard faced
28(5) nickel coating (ENC)
with CoCr-A hardfacing alloy
CF8M
29 (standard for CF8M
S31600 with electroless S31600 S31600
bodies in all designs)(5)
nickel coating (ENC)
S31600
37 and 37H(3) with seat and guide CB7Cu-1 HT R30006 (alloy 6)
hard faced with CoCr-A hardfacing alloy
1. Nonferrous-alloy combinations are also available. Consult your Emerson Process Managementt sales office for details.
2. CA15 is used for NPS 6 and 8 full-size and restricted-trim valves.
3. Trims 3H and 37H have clearances for high-temperature service.
4. Not for use with Whisper Trim I.
5. Not use with Whisper Trim I with 136 mm (5.375 inch) and larger ports.
Table 4. Whisper Trim III Metal Trim Part Materials and Body/Trim Temperature Capabilities (NPS 6 Fisher ED only)
MATERIAL
BAFFLE TEMPERATURE
TRIM
VALVE CAGE (FOR LEVEL SEAT BODY, BONNET CAPABILITY
DESIGNA- CAGE
PLUG RETAINER D3 CAGE RING & BONNET SPACER
TION _C _F
ONLY)
Min Max Min Max
301 (standard Carbon steel WCC carbon steel
for all body NACE with or WC9 chrome 29 343 20 650
materials S17400 HT S41600 HT electroless Steel 410 SST HT moly steel
except nickel coating
S31600) (ENC) CF8M (316 SST) 29 163 20 325
WCC carbon steel
301A S17400 HT S41600 WCC Nitrided Steel S41600 or WC9 chrome moly 232 427 450 800
steel
S31600 with Carbon steel S31600 with WCC carbon steel,
seat and guide NACE with seat hard 29 343 20 650
WC9 chrome moly steel
304 hard faced with S41600 HT electroless Steel faced with
CoCr-A hard- nickel coating CoCr-A hard-
CF8M (316 SST) 29 177 20 350
facing alloy (ENC) facing alloy
S31600 with Carbon steel S31600 with
S31600 with WCC carbon steel,
313 seat and guide NACE with seat hard
electroless WC9 chrome moly
(NACE hard faced with electroless Steel faced with 29 343 20 650
nickel coating steel, or
compatible)(1) CoCr-A hard- nickel coating CoCr-A hard-
(ENC) CF8M (316 SST)
facing alloy (ENC) facing alloy
S31600 with S31600 with WCC carbon steel or
seat and guide seat hard 29 260 20 500
Cr Ct Cr Ct WC9 chrome moly steel
315 hard faced with S31600 faced with
316 SST 316 SST
CoCr-A hard- CoCr-A hard-
CF8M (316 SST) 198 537(2) 325 1000(2)
facing alloy facing alloy
S31600 with S31600 WCC carbon steel 29 427 20 800
seat and guide with seat
318 WC9/Nitrided WC9/Nitrided WC9
hard-faced hard-faced
WC9 chrome moly steel 29 593 20 1100
with CoCr-A with CoCr-A
1. Level D3 cage cannot be certified to NACE. Use 316/ENC cage retainer instead.
2. May be used up to 593_C (1100_F) if manufacturing process controls carbon content to 0.04% minimum or 0.08% maximum.
7
Product Bulletin
51.1:ED
ED Valve June 2010
Table 5. WhisperFlo Metal Trim Part Materials and Valve Body/Trim Temperature Capabilities (NPS 4 and 6 Fisher ED only)
TRIM MATERIAL TEMPERATURE CAPABILITY
VALVE VALVE CAGE
DESIGNA- CAGE SEAT _C _F
BODY PLUG RETAINER
TION Min Max Min Max
901 WCC S41600 S41000 WCC ENC S41600 29 343 20 650
S31600/CoCrA
902 WCC Seat and S41000 WCC ENC S31600/CoCrA 29 343 20 650
Guide
S31600/CoCrA
915 WCC Seat and S41000/Nitride WCC/Nitride S31600/CoCrA 343 427 650 800
Guide
S31600/CoCrA
916 WC9 Seat and S41000/Nitride WC9/Nitride S31600/CoCrA 343 538 650 1000
Guide
S31600/CoCrA
926 WCC Seat and S41000 NACE WCC/NACE/ENC S31600/CoCrA 29 343 20 650
Guide
S31600/CoCrA
316
936 Seat and S31603/CRCT S31600/ENC S31600/CoCrA 198 343 325 650
CF8M
Guide
S31600/CoCrA
316
946 Seat and S31603/CRCT S31600/Nitride S31600/CoCrA 343 538 650 1000
CF8M
Guide
8
Product Bulletin
51.1:ED
June 2010 ED Valve
PACKING
BOX PACKING
STUD BOX
STUDS
SPRING
SPRINGS
ANTI-
EXTRUSION
PACKING
FOLLOWER RING
RING
PACKING
LANTERN VALVE
BONNET
RING
W85331
PACKING
BOX
STUD
SPRINGS
FOLLOWER
PACKING
W8532-1
W7018 / IL
9
Product Bulletin
51.1:ED
ED Valve June 2010
W58521 / IL
Figure 8. Cutaway of ENVIRO-SEAL Bellows Seal Bonnet and Internal Shroud, Showing Bellows
10
Product Bulletin
51.1:ED
June 2010 ED Valve
Table 6. Materials and Temperature Limits for All Other Parts
PART MATERIAL MATERIAL TEMPERATURE CAPABILITY
_C _F
Min Max Min Max
Cast iron valve
body Cap screws Steel SAE Grade 5 29 232 20 450
11
Product Bulletin
51.1:ED
ED Valve June 2010
FLUID TEMPERATURE, _C
0 200 400
1500
FLUID TEMPERATURE, _C 100
1400
0 100 200
600 41.4
40 1200
80
37H
30
1, 37, OR 29 3 2 60
400 25 800
300 20 600 40
1
15 1 OR 37H 2
200 4, 29
400
10
20
100
5 200
1 OR 29 4
0 0 0 0
100 0 100 200 300 400 500
100 0 100 200 300 400 500 600 700 800
20 450 20
FLUID TEMPERATURE, _F 50 FLUID TEMPERATURE, _F
100 100
1400 1400
1200 1200
80 80
1000
PRESSURE DROP, PSI
1000
60 28 OR 29 3 60
800 1, 3, 800
37H
27
600 2 600 40
1, 3, 37 40
400 400
3H 20 20
200 200
2 29 4
0 0 0 0
200 0 400 800 1200 400 0 400 650 800 1200
20 410 1100 325
FLUID TEMPERATURE, _F
FLUID TEMPERATURE, _F
NOTES:
1 DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE PRESSURE RATING OF
THE VALVE MATERIAL USED, EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES.
2 BE ESPECIALLY CAREFUL TO SPECIFY SERVICE TEMPERATURE IF TRIM 3 OR 37 IS SELECTED
AS DIFFERENT THERMAL EXPANSION RATES REQUIRE SPECIAL PLUG CLEARANCES. SPECIFY
TRIM 37H FOR TEMPERATURES ABOVE 210_C (410_F). SPECIFY TRIM 3H FOR TEMPERATURES
ABOVE 427_C (800_F).
3 TRIM 29 MAY BE USED UP TO 103 BAR (1500 PSI) WITH CLEAN, DRY GAS.
4 USE TRIM 27 INSTEAD OF TRIM 29 FOR NONLUBRICATING FLUIDS SUCH
AS SUPERHEATED STEAM OR DRY GASES BETWEEN 149 AND 316_C (300 AND 600_F).
B14707 / IL
Figure 9. Typical Trim Used for All Valves Except NPS 4 and 6 Fisher ED with Whisper Trim III Cage and WhisperFlo Cage
12
Product Bulletin
51.1:ED
June 2010 ED Valve
BONNET
SPACER
CAGE
RETAINER
W33322 / IL
FLUID TEMPERATURE, _C
100 100
1400 1400
1200 1200
80 80
1000
PRESSURE DROP, PSI
1000 301A,
318
60 60
800 800
301, 301A,
318 315
600 40 600 40
304 OR 313
315
400 400
318
20 20
200 200
0 0 0 0
200 0 400 800 1200 400 0 400 650 800 1200
20 1050 325 20
FLUID TEMPERATURE, _F FLUID TEMPERATURE, _F
NOTES:
1 DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE PRESSURE RATING
OF THE BODY MATERIAL USED, EVEN THOUGH THE TRIM SHOWN MAY HAVE HIGHER CAPABILITIES.
A27034 / IL
Figure 11. Typical Trim Used for NPS 6 Fisher ED Valves with Whisper Trim III Cages
13
Product Bulletin
51.1:ED
ED Valve June 2010
Table 7. Valve Body/Trim Temperature Capabilities(1) For All Valves Except NPS 6 Fisher ED with Whisper Trim III Cage and NPS 4
and 6 ED with WhisperFlo Cage
MATERIAL
TEMPERATURE
VALVE BODY/BONNET(2) TRIM CAPABILITY
VALVE SIZE AND DESIGN
MATERIAL DESIGNATION
_C _F
Min Max Min Max
1, 3, 27, or 29 All 29 232 20 450
Cast iron 37 All 29 210 20 410
37H All 210 232 410 450
1 All 29 427 20 800
4 All 29 210 20 410
All (except limited to 338_C [640_F] for
27 29 343 20 650
WCC steel NPS 4 and 6)
29 All 29 149(4) 20 300(4)
37 All 29 210 20 410
37H All 210 427 410 800
1 or 3 All 29 427 20 800
All (except limited to 338_C [640_F] for
27 29 343 20 650
NPS 4 and 6)
WC9 chrome moly 29 All 29 149(4) 20 300(4)
steel
37 All 29 210 20 410
3H All 427 593 800 1100
37H All 210 427 410 800
1 All 29 343 20 650
4 All 46 210 50 410
All (except limited to 338_C [640_F] for
27 46 343 50 650
LCC steel NPS 4 and 6)
29 All 46 149(4) 50 300(4)
37 All 46 210 50 410
37H All 210 343 410 650
27 All 198(3) 343 325(3) 650
CF8M (316 198(3) 149(4) 325(3) 300(4)
28 All
stainless steel)
29 All 198(3) 149(4) 325(3) 300(4)
1. For metal trim parts only. Restricted trim and full-sized limits are the same.
2. Same material also used for bottom flange, if required.
3. May be used down to 254_C (425_F) if manufacturing process includes Charpy impact test.
4. Lubricating service allows usage to 316_C (600_F).
W7065 / IL
W6851-1 / IL
14
Product Bulletin
51.1:ED
June 2010 ED Valve
Table 8. Bonnet Selection Guidelines
IN-BODY PROCESS TEMPERATURE LIMITS(1)
BONNET STYLE PACKING MATERIAL
_C _F
Plain: PTFE V-ring 18 to 232 0 to 450
J Standard for all valves through
NPS 6 valve body with 2-13/16 yoke PTFE/Composition 18 to 232 0 to 450
boss diameter
J Standard for NPS 6 and 8 valves in cast 18 to maximum shown 0 to maximum shown
iron and WCC steel bonnet material with Graphite ribbon/filament
in table 6 in table 6
3-9/16 yoke boss diameter
Style 1 Cast Extension: PTFE V-ring
46 to 427 50 to 800
J Standard for NPS 8 valves in S31600 PTFE/Composition
bonnet material with 3-9/16 yoke boss 46 to to maximum shown 50 to maximum shown
diameter Graphite ribbon/filament
in table 6 in table 6
Style 2 Cast Extension: PTFE V-ring
J Optional for NPS 2 through 4 valves with 101 to 427 150 to 800
2-13/16 inch yoke boss diameter PTFE/Composition
J Optional for NPS 6 and 8 valves
with 3-9/16 yoke boss diameter. Not 101 to maximum shown 150 to maximum shown
available for NPS 8 valve in S31600 Graphite ribbon/filament
in table 6 in table 6
bonnet material
For exceptional stem sealing capabilities. See
PTFE Bulletin 59.1:070, ENVIRO-SEAL Bellows Seal
ENVIRO-SEAL bellows seal bonnet Bonnets, for pressure/temperature ratings.
Graphite ULF
1. These in-body process temperatures assume an outside, ambient temperature of 21_C (70_F) and no insulation on the bonnet. When using any packing at low process temperatures,
a cast extension bonnet may have to be used to prevent packing damage which could result from the formation of valve stem frost. Material selection for trim and other components will
also be limiting factors.
15
Product Bulletin
51.1:ED
ED Valve June 2010
Table 10. Metal Trim Part Materials for Compatibility with NACE MR0175 / ISO 15156 and MR0103 (Sour Service) Specifications,
Environmental Restrictions Apply, Refer to Standard. Contact your Emerson Process Management Sales Office for information on
NACE MR0175 / ISO 15156 and NACE MR0103.
Seat Ring Optional Valve Stem, Packing
for Standard Liner for Follower, Lantern
Trim Designation Valve Plug Cage Load Ring(1)
Metal Seat Metal Seat Ring, Packing Box
Construction (EAD only) Ring, and Pin
S31600 with
85(2) S31600 electroless nickel S31600 S31600
coating (ENC)
S31600
S31600 with
with seat hard S20910 (Valve Stem)
86(2) electroless nickel R30006 (alloy 6) ---
faced with CoCr-A S31600 N05500
coating (ENC)
hardfacing alloy (All Other Parts)
S31600
S31600 with
with seat and
87 electroless nickel R30006 (alloy 6) ---
guide hard faced
coating (ENC)
with CoCr-A hardfacing alloy
1. NPS 8 valve only.
2. Not use with Whisper Trim I with 136 mm (5.375 inch) and larger ports.
16
Product Bulletin
51.1:ED
June 2010 ED Valve
Table 11. Port Diameters, Valve Plug Travel, and Stem and Yoke Boss Diameters
MAX VALVE
PORT
VALVE SIZE, NPS PLUG STEM AND YOKE BOSS DIAMETERS
DIAMETER
TRAVEL
ED or EDR EAD Standard Optional
Restricted- Restricted- Stem Yoke Boss Stem Yoke Boss
Full-Sized Full-Sized
Capacity Capacity
Trim Trim mm Inch mm Inch mm Inch mm Inch mm Inch mm Inch
Trim Trim
1 1-1/2 1 2 33.3 1.3125 19 0.75 9.5 3/8 54 2-1/8 12.7 1/2 71 2-13/16
--- 2 --- --- 33.3 1.3125 19 0.75 12.7 1/2 71 2-13/16 --- --- --- ---
1-1/2 --- 2 --- 47.6 1.875 19 0.75 9.5 3/8 54 2-1/8 12.7 1/2 71 2-13/16
--- 2-1/2 --- 3 47.6 1.875 19 0.75 1.7 1/2 71 2-13/16 --- --- --- ---
2 3 --- 4 58.7 2.3125 29 1.125 12.7 1/2 71 2-13/16 19.1 3/4 90 3-9/16
2-1/2 4 3 6 73.0 2.875 38 1.5 12.7 1/2 71 2-13/16 19.1 3/4 90 3-9/16
3 --- 4 --- 87.3 3.4375 38 1.5 12.7 1/2 71 2-13/16 19.1 3/4 90 3-9/16
87(3) 3.4375(3) 76(3) 3(3) 19.1 3/4 90 3-9/16
4 --- 6 --- 4.375
12.7 1/2 71 2-13/16
111.1 51 2 25.4 1 127 5
177.8(2) 7(2) 51(2) 2(2)
6(1) --- --- --- 25.4 1
136(3) 5.375(3) 76(3) 3(3)
19.1 3/4 90 3-9/16 or or 127 5
51 2 1-1/4
8(1) --- --- --- 203.2 8 31.8
76 3
1. Not available in EDR valve.
2. Standard-travel cages.
3. Whisper Trim III (NPS 6 ED) and WhisperFlo cages (NPS 4 and 6 ED).
Table 12. Bolting Materials and Temperature Limits for Compatibility with NACE MR0175-2002, NACE MR0175/ISO 15156, and
NACE MR0103. Environmental restrictions may apply
VALVE BODY TEMPERATURE
MATERIAL CAPABILITIES
BOLTING MATERIAL
_C _F
Min Max Min Max
Non-exposed bolting (Standard)
WCC and Studs Steel SA-193-B7
48(2) 427 55(2) 800
CF8M (316 SST) Nuts Steel SA-194-2H
Exposed bolting (Optional)
Requires Derating of Valve(1) When These Body-to-Bonnet Bolting Materials are Used
Studs Steel SA-193-B7M
WCC and CF8M 48(2) 427 55(2) 800
Nuts Steel SA-194-2HM
1. Derating is not required for CL300 valves. Derating may be required for valves rated at CL600. Contact your Emerson Process Management sales office for assistance in determining
the derating of valves when these body-to-bonnet bolting materials are used.
2. 29_C (20_F) with WCC valve body material.
17
Product Bulletin
51.1:ED
ED Valve June 2010
100 100
1400 1400
1200 1200
400 400
20 20
200 200
2 85 2 85
0 0 0 0
200 100 0 100 200 300 400 500 600 700 400 0 400 650 800 1200
50 325 100
FLUID TEMPERATURE, _F
FLUID TEMPERATURE, _F
FOR STANDARD METAL SEATING WITH FOR STANDARD METAL SEATING WITH CL600 1
CL600 1 WCC OR LCC VALVE BODY 316 STAINLESS STEEL (CF8M) VALVE BODY
NOTES:
1 DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE PRESSURE RATING
OF THE VALVE MATERIAL USED, EVEN THOUGH THE TRIM SHOWN MAY HAVE HIGHER CAPABILITIES.
2 USE TRIM 87 INSTEAD OF TRIM 85 FOR NONLUBRICATING FLUIDS SUCH
AS SUPERHEATED STEAM OR DRY GASES BETWEEN 149 AND 316_C (300 AND 600_F).
C05752 / IL
Figure 13. Typical Trim Used for NACE MR0175 / ISO 15156 and NACE MR0103. Environmental restrictions may apply
18
Product Bulletin
51.1:ED
June 2010 ED Valve
MATCH LINE
MATCH LINE
FOR
FOR
ACTUATOR
ACTUATOR
G
G
1 1
B B
A A
10A7397B
AR4967a A09261 / IL
A09252 / IL
Figure 14. Fisher ED and EDR Dimensions (also see tables 13, 14, and 15)
19
Product Bulletin
51.1:ED
ED Valve June 2010
VALVE ED EDR
SIZE, Stem Diameter Stem Diameter
NPS mm
9.5 12.7 19.1 25.4 or 31.8 9.5 12.7 19.1
1 127 149 --- --- 113 124 ---
1-1/2 124 146 --- --- 122 133 ---
2 --- 165 162 --- --- 148 140
2-1/2 --- 187 184 --- --- 157 152
3 --- 191 187 --- --- 167 159
4 --- 221 217 238 --- 198 191
6(1) --- --- 251 270 --- --- ---
6(2) --- --- 312 330 --- --- ---
8 --- --- 375(3) --- --- --- ---
Inch
3/8 1/2 3/4 1 or 1-1/4 3/8 1/2 3/4
1 5.00 5.88 --- --- 4.44 4.88 ---
1-1/2 4.88 5.75 --- --- 4.81 5.25 ---
2 --- 6.50 6.38 --- --- 5.81 5.50
2-1/2 --- 7.38 7.25 --- --- 6.31 6.00
3 --- 7.50 7.38 --- --- 6.56 6.25
4 --- 8.69 8.56 9.38 --- 7.81 7.50
6(1) --- --- 9.88 10.62 --- --- ---
6(2) --- --- 12.26 13.00 --- --- ---
8 --- --- 14.75(3) --- --- --- ---
1. All except Whisper Trim III and WhisperFlo cages.
2. Whisper Trim III and WhisperFlo cages.
3. Available only in cast iron or WCC steel for the stem diameter with plain bonnet.
VALVE Style 1 Ext. Bonnet Style 2 Ext. Bonnet ENVIRO-SEAL Bellows Seal Bonnet
SIZE, Stem Diameter Stem Diameter Stem Diameter
NPS mm
9.5 12.7 19.1 25.4 or 31.8 9.5 12.7 19.1 9.5 12.7 19.1
1 213 251 --- --- 303 319 --- 321 --- ---
1-1/2 210 248 --- --- 300 316 --- 317 --- ---
2 --- 267 --- --- --- 465 --- --- 384 ---
2-1/2 --- 289 272 --- --- 492 --- --- --- ---
3 --- 292 297 --- --- 495 487 --- 518 518
4 --- 322 327 370 --- 526 518 --- 541 ---
6(1) --- --- 357 402 --- --- 543 --- --- 573
6(2) --- --- 418 462 --- --- 604 --- --- ---
8 --- --- 421 450 --- --- 621 --- --- ---
Inch
3/8 1/2 3/4 1 or 1-1/4 3/8 1/2 3/4 3/8 1/2 3/4
1 8.38 9.88 --- --- 11.94 12.56 --- 12.62 --- ---
1-1/2 8.25 9.75 --- --- 11.81 12.44 --- 12.50 --- ---
2 --- 10.50 --- --- --- 18.31 --- --- 15.12 ---
2-1/2 --- 11.38 10.69 --- --- 19.38 --- --- --- ---
3 --- 11.50 11.69 --- --- 19.50 19.19 --- 20.38 20.38
4 --- 12.69 12.88 14.56 --- 20.69 20.38 --- 21.31 ---
6(1) --- --- 14.06 15.81 --- --- 21.38 --- --- 22.56
6(2) --- --- 16.44 18.19 --- --- 23.76 --- --- ---
8 --- --- 16.56 17.75 --- --- 24.44 --- --- ---
1. Standard-travel cages.
2. Whisper Trim III and WhisperFlo cages.
20
Product Bulletin
51.1:ED
June 2010 ED Valve
Table 16. Fisher EAD Dimensions
AA MATCH LINE
FOR
VALVE CL150 CL300 CL600 ACTUATOR
SIZE, End Connection Style(1)
NPS RF RTJ RF RTJ BW, SW or RF RTJ
mm
1 92 98 98 105 105 105
2 127 133 133 141 143 144
3 149 156 159 167 168 170 DD
4 176 183 184 197 197 198
6 225 232 237 244 254 256
Inch
1 3.62 3.88 3.88 4.12 4.12 4.12
2 5.00 5.25 5.25 5.56 5.62 5.69
AA
3 5.88 6.12 6.25 6.56 6.62 6.69 NOTE:
4 6.94 7.19 7.25 7.56 7.75 7.81 FOR DIMENSIONS OF
6 8.88 9.12 9.31 9.62 10.00 10.06 VALVES WITH EN (OR
OTHER) END CON-
1. End connection style abbreviations: BW - Buttwelding, FF - Flat Faced, Scrd -
Screwed, SW - Socketweld, RF - Raised Face, RTJ - Ring Type Joint. NECTIONS. CONSULT
YOUR EMERSON SALES
OFFICE. AA
AU6190A
A09272 / IL
21
Product Bulletin
51.1:ED
ED Valve June 2010
Coefficients
Table 18. Fisher EAD, Quick Opening Cage, With Liner
Quick Opening
With Liner Characteristic
Maximum Coeffs.
Port Diameter Flow for 6 Valve Opening—Percent of Total Travel
Valve Travel(1)
Coeffi- mm FL(3)
Size, NPS
cient (0.25 in)
mm Inches mm Inches 10 20 30 40 50 60 70 80 90 100
Travel(2)
Cv 14.2 5.14 9.24 13.1 16.2 18.8 20.9 22.4 23.4 24.0 24.0 0.90
1 33.3 0.3125 19 0.75 Kv 12.3 4.45 7.99 11.3 14.0 16.3 18.1 19.4 20.2 20.8 20.8 ---
XT 0.800 0.629 0.703 0.761 0.809 0.775 0.713 0.677 0.652 0.630 0.630 ---
Cv 29.4 8.77 17.1 26.2 36.1 45.4 53.4 59.3 63.6 67.3 70.7 0.76
47.6 1.875 19 0.75 Kv 25.4 7.59 14.8 22.7 31.2 39.3 46.2 51.3 55.0 58.2 61.2 ---
XT 0.573 0.480 0.513 0.568 0.570 0.577 0.589 0.628 0.618 0.656 0.656 ---
2
Cv 17.3 5.91 10.1 15.1 21.7 29.4 37.3 43.7 48.5 52.4 55.2 0.60
33.3 1.3125
(4) (4) 19 0.75 Kv 15.0 5.11 8.74 13.1 18.8 25.4 32.3 37.8 42.0 45.3 47.7 ---
XT 0.543 0.404 0.584 0.570 0.522 0.478 0.431 0.396 0.370 0.344 0.326 ---
Cv 30.6 24.2 47.2 77.8 108 133 148 159 171 181 183 0.76
73.0 2.875 38 1.5 Kv 26.5 20.9 40.8 67.3 93.4 115 128 138 148 157 158 ---
XT 0.540 0.517 0.534 0.504 0.545 0.582 0.636 0.651 0.616 0.575 0.569 ---
3
Cv 29.8 7.96 15.5 25.7 37.4 49.0 61.2 72.5 83.1 92.8 102 0.60
47.6 1.875
(4) (4) 19 0.75 Kv 25.8 6.89 13.4 22.2 32.4 42.4 52.9 62.7 71.9 80.3 88.2 ---
XT 0.576 0.549 0.624 0.603 0.541 0.525 0.482 0.452 0.422 0.391 0.349 ---
Cv 37.1 22.3 46.3 77.1 117 155 180 197 212 230 235 0.72
87.3 3.4375 38 1.5 Kv 32.1 19.3 40.0 66.7 101 134 156 170 183 199 203 ---
XT 0.580 0.616 0.547 0.537 0.531 0.529 0.575 0.629 0.635 0.609 0.620 ---
4
Cv 31.4 14.4 28.3 46.1 66.7 87.5 107 124 138 149 160 0.61
58.7 2.3125
(4) (4) 29 1.125 Kv 27.2 12.5 24.5 39.9 57.7 75.7 92.6 107 119 129 138 ---
XT 0.548 0.509 0.533 0.505 0.486 0.482 0.465 0.443 0.416 0.387 0.354 ---
Cv 50.0 39.8 84.0 150 219 279 332 379 420 435 435 0.71
111.1 4.375 51 2 Kv 43.3 34.4 72.7 130 189 241 287 328 363 376 376 ---
XT 0.578 0.597 0.599 0.577 0.581 0.581 0.578 0.565 0.527 0.533 0.533 ---
6
Cv 38.7 23.9 47.1 74.9 109 142 174 201 219 244 248 0.59
73.0 2.875
(4) (4) 38 1.5 Kv 33.5 20.7 40.7 64.8 94.3 123 151 174 189 211 215 ---
XT 0.353 0.353 0.353 0.353 0.353 0.356 0.352 0.353 0.352 0.353 0.354 ---
1. When using 655-EAD as a control valve for on-off service, the maximum travel for sizing purposes is 0.75 inch (19 mm).
2. When sizing self-operated regulators, use coefficients listed for 0.25 inch (6 mm) travel.
3. At 100% travel.
4. Restricted trim.
22
Product Bulletin
51.1:ED
June 2010 ED Valve
23
Product Bulletin
51.1:ED
ED Valve June 2010
24
Product Bulletin
51.1:ED
June 2010 ED Valve
25
Product Bulletin
51.1:ED
ED Valve June 2010
26
Product Bulletin
51.1:ED
June 2010 ED Valve
27
Product Bulletin
51.1:ED
ED Valve June 2010
28
Product Bulletin
51.1:ED
June 2010 ED Valve
29
Product Bulletin
51.1:ED
ED Valve June 2010
30
Product Bulletin
51.1:ED
June 2010 ED Valve
31
Product Bulletin
51.1:ED
ED Valve June 2010
32
Product Bulletin
51.1:ED
June 2010 ED Valve
Table 27. Fisher ED, CL125-600, Equal Percentage Cage, Flow Down
Equal Percentage
Equal Percentage Characteristic
Valve Port Maximum Flow Valve Opening—Percent of Total Travel
Size, Diameter Travel Coeffi- FL(1)
NPS mm Inches mm Inches cient 10 20 30 40 50 60 70 80 90 100
Cv 0.783 1.54 2.20 2.89 4.21 5.76 7.83 10.9 14.1 17.2 0.88
1 33.3 1.3125 19 0.75 Kv 0.677 1.33 1.90 2.50 3.64 4.98 6.77 9.43 12.2 14.9 ---
XT 0.766 0.614 0.587 0.667 0.672 0.687 0.743 0.760 0.733 0.667 ---
Cv 1.52 2.63 3.87 5.41 7.45 11.2 17.4 24.5 30.8 35.8 0.84
Kv 1.31 2.27 3.35 4.68 6.44 9.69 15.1 21.2 26.6 31.0 ---
47.6 1.875 19 0.75
XT 0.780 0.735 0.716 0.715 0.738 0.727 0.690 0.685 0.685 0.679 ---
1-1/2 Fd 0.64 0.63 0.63 0.64 0.46 0.45 0.30 0.31 0.35 0.38 ---
Cv 1.12 1.56 2.22 3.10 4.27 6.17 9.01 13.1 18.2 23.1 0.91
33.3 1.3125
(2) (2) 19 0.75 Kv 0.969 1.35 1.92 2.68 3.69 5.34 7.79 11.3 15.7 20.0 ---
XT 0.821 0.864 0.820 0.703 0.721 0.679 0.665 0.639 0.650 0.700 ---
Cv 1.66 2.93 4.66 6.98 10.8 16.5 25.4 37.3 50.7 59.7 0.85
Kv 1.44 2.53 4.03 6.04 9.34 14.3 22.0 32.3 43.9 51.6 ---
58.7 2.3125 29 1.125
XT 0.827 0.834 0.774 0.727 0.687 0.684 0.702 0.736 0.686 0.687 ---
2 Fd 0.41 0.50 0.53 0.58 0.37 0.32 0.27 0.26 0.29 0.31 ---
Cv 0.923 1.42 2.09 2.84 4.11 5.83 8.58 12.8 18.5 24.3 0.88
33.3 1.3125
(2) (2) 19 0.75 Kv 0.798 1.23 1.81 2.46 3.56 5.04 7.42 11.1 16.0 21.0 ---
XT 0.775 0.744 0.742 0.707 0.715 0.714 0.714 0.641 0.621 0.649 ---
Cv 3.43 7.13 10.8 15.1 22.4 33.7 49.2 71.1 89.5 99.4 0.84
Kv 2.97 6.17 9.34 13.1 19.4 29.2 42.6 61.5 77.4 86.0 ---
73.0 2.875 38 1.5
XT 0.778 0.702 0.678 0.677 0.658 0.654 0.661 0.665 0.661 0.660 ---
2-1/2 Fd 0.45 0.49 0.49 0.47 0.35 0.32 0.30 0.24 0.25 0.27 ---
Cv 1.57 2.57 3.82 5.44 7.64 11.5 18.2 26.7 35.1 43.9 0.89
47.6 1.875
(2) (2) 19 0.75 Kv 1.36 2.22 3.30 4.71 6.61 9.95 15.7 23.1 30.4 38.0 ---
XT 0.801 0.756 0.713 0.677 0.648 0.672 0.628 0.635 0.706 0.710 ---
Cv 4.32 7.53 10.9 17.1 27.2 43.5 66.0 97.0 120 136 0.82
Kv 3.74 6.51 9.43 14.8 23.5 37.6 57.1 83.9 104 118 ---
87.3 3.4375 38 1.5
XT 0.774 0.706 0.682 0.635 0.616 0.602 0.663 0.693 0.670 0.675 ---
3 Fd 0.52 0.63 0.68 0.39 0.36 0.29 0.26 0.28 0.30 0.32 ---
Cv 1.75 3.11 4.77 7.07 10.7 17.0 27.9 41.5 58.0 70.7 0.87
58.7 2.3125
(2) (2) 29 1.125 Kv 1.51 2.69 4.13 6.12 9.26 14.7 24.1 35.9 50.2 61.2 ---
XT 0.944 0.840 0.803 0.757 0.735 0.642 0.531 0.613 0.629 0.702 ---
Cv 5.85 11.6 18.3 30.2 49.7 79.7 125 171 205 224 0.82
Kv 5.06 10.0 15.8 26.1 43.0 68.9 108 148 177 194 ---
111.1 4.375 51 2
XT 0.731 0.650 0.643 0.645 0.632 0.625 0.672 0.742 0.737 0.716 ---
4 Fd 0.45 0.42 0.40 0.33 0.30 0.28 0.23 0.24 0.26 0.28 ---
Cv 3.82 7.65 11.4 16.9 25.5 38.2 60.5 85.7 105 112 0.89
73.0 2.875
(2) (2) 38 1.5 Kv 3.30 6.62 9.86 14.6 22.1 33.0 52.3 74.1 90.8 96.9 ---
XT 0.746 0.700 0.694 0.669 0.640 0.627 0.591 0.644 0.735 0.813 ---
-continued-
33
Product Bulletin
51.1:ED
ED Valve June 2010
Table 27. Fisher ED, CL125-600, Equal Percentage Cage, Flow Down (continued)
Valve Port Maximum Flow Valve Opening—Percent of Total Travel
Size, Diameter Travel Coeffi- FL(1)
NPS mm Inches mm Inches cient 10 20 30 40 50 60 70 80 90 100
Cv 12.9 25.8 43.3 67.4 104 162 239 316 368 394 0.85
Kv 11.2 22.3 37.5 58.3 90.0 140 207 273 318 341 ---
177.8 7 51 2
XT 0.688 0.680 0.682 0.709 0.700 0.720 0.736 0.744 0.780 0.778 ---
6 Fd 0.39 0.44 0.47 0.33 0.29 0.22 0.22 0.24 0.25 0.26 ---
Cv 5.40 10.1 15.8 26.7 45.2 71.2 111 169 232 274 0.88
111.1 4.375
(2) (2) 51 2 Kv 4.67 8.74 13.7 23.1 39.1 61.6 96.0 146 201 237 ---
XT 0.834 0.834 0.735 0.654 0.626 0.613 0.614 0.610 0.629 0.695 ---
Cv 18.5 38.0 58.4 86.7 130 189 268 371 476 567 0.85
8 203.2 8 51 2 Kv 16.0 32.9 50.5 75.0 112 163 232 321 412 490 ---
XT 0.727 0.623 0.600 0.588 0.580 0.587 0.599 0.611 0.671 0.724 ---
Cv 27.0 58.1 105 188 307 478 605 695 761 818 0.86
Kv 23.4 50.3 90.8 163 266 413 523 601 658 708 ---
8 203.2 8 76 3
XT 0.644 0.654 0.636 0.611 0.643 0.615 0.725 0.809 0.804 0.807 ---
Fd 0.28 0.26 0.23 0.20 0.17 0.22 0.24 0.25 0.25 0.26 ---
1. At 100% travel.
2. Restricted trim.
34
Product Bulletin
51.1:ED
June 2010 ED Valve
Notes: The coefficients shown on this page are also appropriate for EDR.
35
Product Bulletin
51.1:ED
ED Valve June 2010
Table 29. Fisher ED, CL125-600, Whisper Trim III Cage, Flow Up
Linear
Whisper Trim III Characteristic(2)
Valve Port Maximum Flow Valve Opening—Percent of Total Travel
Size, Diameter Travel Coeffi- XT(1)
NPS mm Inches mm Inches cient Minimum(3) 20 30 40 50 60 70 80 90 100
A3 DP/P10.6
Cv 4.67 68.2 92.0 129 163 196 228 257 279 295 0.714
6 136.5 5.375 76 3
Kv 4.04 59.0 79.6 112 141 170 197 222 241 255 ---
B3 DP/P10.75
Cv 4.67 38.2 66.9 94.5 120 144 167 190 211 228 0.473
6 136.5 5.375 76 3
Kv 4.04 33.0 57.9 81.7 104 125 144 164 183 197 ---
C3 DP/P10.85
Cv 4.67 28.0 41.3 55.3 69.3 83.0 97.0 110 124 138 0.563
6 136.5 5.375 76 3
Kv 4.04 24.2 35.7 47.8 59.9 71.8 83.9 95.2 107 119 ---
D3 DP/P10.99
Cv 4.67 6.67 9.50 19.9 31.4 46.0 61.0 75.7 89.7 104 0.563
6 136.5 5.375 76 3
Kv 4.04 5.77 8.22 17.2 27.2 39.8 52.8 65.5 77.6 90.0 ---
1. This column lists XT factors for Whisper Trim III cages at 100% travel.
2. Level D exhibits an equal percentage characteristic for the first 38 mm (1.5 inches) of travel, then linear characteristic.
3. This coefficient is minimum rather than 10% open. Valves should not be required to throttle at less than the specified minimum coefficient for an extended period of time. Erosion
damage to the valve may result.
36
Product Bulletin
51.1:ED
June 2010 ED Valve
Specifications
Available Configurations Maximum Pressure Drop(2)
ED: Single-port, globe-style control valve with Same as maximum inlet pressure for specific
cage guiding, balanced valve plug, and construction defined above, except where further
push-down-to-close valve plug action (figures 1 limited as follows:
and 2) All Valves Except Those with Whisper Trim III
EAD: Angle version of ED control valve, used to and WhisperFlo Cages: See figure 9.
facilitate piping or in applications where a Valves with Whisper Trim III Cages (NPS 6
self-draining valve is desired (figure 3) ED): See figure 11 except where further limited by
EDR: Same as ED control valve except with the following max n-P/P1 ratio(4)—0.60 for level
push-down-to-open valve plug action (figure 4) A3 cage, 0.75 for level B3 cage, 0.85 for level C3
cage, or 0.99 for level D3 cage
Valves for NACE MR0175 / ISO 15156 and
Valve Sizes
MR0103: See figure 13
See table 2
Shutoff Classifications per ANSI/FCI 70-2
and IEC 60534-4
End Connection Styles(1)(2) Class II: Standard with single graphite ring and
Cast Iron Valves. 33 through 203 mm (1.3125 through 8-inch) port
Flanged: ED, NPS 1 through 8, J CL125 flat-face size
or J CL250 raised-face flanges per ASME B16.1 Class III: Optional for valves with single graphite
Steel and Stainless Steel Valves. piston ring and 87 mm (3.4375 inch) or larger port
Flanged: J CL150, 300, or 600 raised-face (RF) diameter
or ring-type joint (RTJ) flanges per Class IV: For valves with multiple graphite piston
ASME B16.5 rings and 111 mm (4.375 inch) or larger port
Screwed or Socket Welding: NPS 1 through 2, diameter
consistent with ASME B16.11 Class V High-Temperature: For valves with port
Buttwelding: NPS 1 through 8 . diameters from 73 through 203.2 mm (2.875
Schedules 40 or 80 consistent with ASME B16.25 through 8-inch) with optional C-seal trim. See
table 1
Socket weld end connection style is not available
for EAD. Construction Materials
Also, see table 2 and figures 14 and 15
Valve Body, Bonnet, and Bonnet Spacer or
Bottom Flange, if used: J Cast iron, J WCC
Maximum Inlet Pressures and Temperatures(1)(2) carbon steel, J 316 stainless steel, J LCC
carbon steel, J WC9 chrome moly steel, or
As listed below, unless limited by maximum J other materials upon request
pressure drop or material temperature capabilities Valve Plug, Cage, and Metal Seating Parts.
Cast Iron Valves. All Valves Except Those with Whisper Trim III and
Flanged: Consistent with CL125B or 250B per WhisperFlo Cages: See table 3.
ASME B16.1 Valves with Whisper Trim III and WhisperFlo
Steel and Stainless Steel Valves. Cages (NPS 4 and 6 ED): See tables 4 and 5.
Flanged: Consistent with CL150, 300, and 600(3) Valves for NACE Specification: See table 10.
per ASME B16.34 Bellows Seal Assembly: J 316L stainless steel
Screwed or Welding: Consistent with CL600(3) per or J N04400
ASME B16.34 All Other Parts: See table 6
- continued -
37
Product Bulletin
51.1:ED
ED Valve June 2010
Specifications (continued)
Material Temperature Capabilities(2) See figure 8 for view of ENVIRO-SEAL bellows
Valve Body/Trim Combinations. seal bonnet. Also, see Bulletin 59.1:070,
All Valves Except Those with Whisper Trim III and ENVIRO-SEAL Bellows Seal Bonnets, for further
WhisperFlo Cages: See table 7. information
Valves with Whisper Trim III Cages (NPS 6 ED):
See table 4. Packing Arrangements
Valves with WhisperFlo Cages (NPS 4 and 6 ED): J Single PTFE V-ring (standard), J double
See table 5. arrangements, J leak-off arrangements,
All Other Parts: See table 6 J ENVIRO-SEAL packing system. See figure 7
for ENVIRO-SEAL configuration.
Flow Characteristics ENVIRO-SEAL Packing Systems in vacuum
Standard Cages: J Quick-opening, J linear, or service: Standard ENVIRO-SEAL packing
J equal percentage systems can be used in vacuum service with
Whisper Trim and WhisperFlo Cages: Linear packing rings in standard orientation. Do not
reverse the ENVIRO-SEAL PTFE packing rings.
See Bulletin 59.1:061, ENVIRO-SEAL Packing
Flow Directions
Systems for Sliding-Stem Valves, for further
ED or EAD: J Standard Cage--Normally down, information.
J Whisper Trim and WhisperFlo Cages—Always
up Approximate Weights
EDR: J Standard Cage--Normally up, J Whisper
NPS 1: 14 kg (30 lb)
Trim Cage—Always down
NPS 1-1/2: 20 kg (45 lb)
NPS 2: 39 kg (85 lb)
Flow Coefficients and Noise Level Prediction NPS 2-1/2: 45 kg (100 lb)
See table 9, the section titled Coefficients in this NPS 3: 57 kg (125 lb)
bulletin, and Catalog 12 NPS 4: 77 kg (170 lb)
NPS 6: 159 kg (350 lb)
Port Diameters and Valve Plug Travels NPS 8: 408 kg (900 lb)
See table 11
Additional Options
Yoke Boss and Stem Diameters J Seal welding of EDR valve body/bonnet joint
for temperatures above 232_C (450_F),
See table 11 J lubricator, J lubricator/isolating valve, J drilled
and tapped connection in extension bonnet for
Typical Bonnet Styles leak-off service, J valve body drain plug, J style
J Plain or J extension. See figures 14 and 15 for 3 fabricated extension bonnet made on order to a
standard dimensions. See table 8 for selection specific length for cryogenic service, J style NS
guidelines. bonnet for seismic service requirements,
J ENVIRO-SEAL bellows seal bonnet. See figure J packings suitable for nuclear service, J C-seal
14 for standard dimensions. trim for Class V high-temperature shutoff
1. EN (or other) ratings and end connections can usually be supplied; consult your Emerson Process Management sales office.
2. The pressure/temperature limits in this bulletin and in any applicable standard limitations should not be exceeded.
3. Certain bonnet bolting material selections may require a CL600 easy-e valve assembly to be derated. Contact your Emerson Process Management sales office for more information.
4. Limitation based on excessive noise increases if max nP/P1 ratio for a given cage level is exceeded.
38
Product Bulletin
51.1:ED
June 2010 ED Valve
39
Product Bulletin
51.1:ED
ED Valve June 2010
Note
Neither Emerson, Emerson Process
Management, nor any of their affiliated
entities assumes responsibility for the
selection, use, or maintenance of any
product. Responsibility for the
selection, use, and maintenance of any
product remains with the purchaser
and end user.
Fisher, easy-e, Whisper Trim, WhisperFlo, and ENVIRO-SEAL are marks owned by one of the companies in the Emerson Process Management
business division of Emerson Electric Co. Emerson Process Management, Emerson, and the Emerson logo are trademarks and service marks of
Emerson Electric Co. All other marks are the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they
are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or
applicability. All sales are governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the
designs or specifications of such products at any time without notice. Neither Emerson, Emerson Process Management, nor any of their affiliated
entities assumes responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use, and maintenance of
any product remains solely with the purchaser and end user.
EFisher
40 Controls International LLC 1983, 2010; All Rights Reserved