Professional Documents
Culture Documents
MOD 6 CHAPTER 2 TEST 1 - Questions
MOD 6 CHAPTER 2 TEST 1 - Questions
MOD 6 CHAPTER 2 TEST 1 - Questions
Question 1/31
K-Monel
A. Composition of Nickel, Copper and Aluminium.
C. Nonmagnetic Material.
Question 2/31
Standard Aluminum Alloy when coaled with a thin layer of pure Aluminium is known as :
A. Alclad.
B. Pureclad or Alclad.
C. Dural.
D. Artificially Aged.
Question 3/31
Al Alloy designated by symbol -W indicate :
A. Solution heat treated, unstable tempered.
B. Annealed.
Question 4/31
Which of the following is used as Turbine Blade Material :
A. Nickel.
B. (b) Nimonic.
C. (c) Steel.
D. (d) Titanium.
1
MOD 6 CHAPTER 2 TEST 1
Question 5/31
Which Alloy posses good casting characteristics and embodies fire hazards :
A. Titanium.
B. Steel.
C. Aluminium.
D. Magnesium.
Question 6/31
Titanium is used for a/c construction, because it has :
D. None above.
Question 7/31
'Monel' is
D. None
Question 8/31
Bronzes are
D. None
2
MOD 6 CHAPTER 2 TEST 1
Question 9/31
Extrusion of Aluminium Alloys produces
A. T-sections
B. Z-sections
D. All
Question 10/31
Alloy designated by 'T 3' indicates :
A. Annealed.
D. Artificially Aged.
Question 11/31
The lightest structural Metal is :
A. Aluminium.
B. Magnesium.
C. Copper.
D. Iron.
Question 12/31
The most commonly used quenching liquid is
A. Brine.
B. Water.
C. Oil.
D. All above.
3
MOD 6 CHAPTER 2 TEST 1
Question 13/31
4000 series of Al alloy contains .
A. Mg
B. Si
C. Zn
Question 14/31
Most appropriate material can be used in the vicinity of compass
A. K- monel
B. Monel
C. Inconel
Question 15/31
The tester is used for non -ferrous metal
A. Barcol
B. Brinell
C. Rockwell
Question 16/31
Cast Aluminium Bronze contains
A. 89% copper, 9% Aluminium
Question 17/31
MTCS about Barcol Tester
A. It requires experienced person to operate
Question 18/31
Beryllium Cu physical properties can be increased by
A. Heat treatment
B. Stress relieving
C. Full annealing
4
MOD 6 CHAPTER 2 TEST 1
Question 19/31
Cold water quenching
A. 80 degree F
B. 85 degree F
C. 105 degree F
Question 20/31
INCONEL has .......... percent greater strength than Nickel.
A. 30 %.
B. 50 %.
C. 25 %.
D. 0.50 %
Question 21/31
Full annealing of commonly used alloys done at ………..degree F for ………, followed by an air cool.
A. 1500 deg. F for 1 hour.
Question 22/31
On BARCOL tester the hardness is indicated on a dial conveniently divided into………….. graduations.
A. 100.
B. 50.
C. 1000.
D. 10
5
MOD 6 CHAPTER 2 TEST 1
Question 23/31
For intricate shapes or items with internal passages, such as turbine blades, ……….. may be the most
economical process.
A. Cold working.
B. Forging.
C. Casting.
D. Extruding
Question 24/31
…….. is the most extruded metal used in aircraft.
A. Copper.
B. Iron.
C. Magnesium.
D. Aluminum
Question 25/31
Die cast used in aircraft are
A. Aluminum
B. Magnesium
C. Titanium
D. Both (a) & (b)
Question 26/31
Molten metal poured into the mold under the force of gravity in..
A. Sand casting
B. Die casting
C. Permanent mold casting
D. Both (a) & (c) are correct
Question 27/31
Aluminum melts at ......... deg. F
A. 1150
B. 1250
C. 950
D. 850
6
MOD 6 CHAPTER 2 TEST 1
Question 28/31
Commercially pure Aluminum has tensile strength of ..
A. 13000 psi
B. 15000 psi
C. 65000 psi
D. 25000 psi
Question 29/31
Most Aluminum sheets used in aircraft construction of thickness range from..
A. 0.05 to 0.015 inch
B. 0.016 to 0.030 inch
C. 0.016 to 0.096 inch
D. 0.096 to 0.106 inch
Question 30/31
Wrought aluminum alloy may be shaped by
A. Rolling
B. Drawing
C. Forging
D. All
Question 31/31
Aluminum alloy castings are produced by
A. Sand cast
B. Permanent mold cast
C. Die cast
D. All