Professional Documents
Culture Documents
Grizzly Industrial, Inc.
Grizzly Industrial, Inc.
MODEL G1067Z
InStruction Manual
3. KEEP WORK AREA CLEAN. Cluttered 7. NEVER FORCE TOOL. It will do the job
areas and benches invite accidents. better and safer at the rate for which it was
designed.
4. NEVER USE IN DANGEROUS ENVIRON-
MENT. DO NOT use power tools in damp 8. USE RIGHT TOOL. DO NOT force tool or
or wet locations, or where any flammable attachment to do a job for which it was not
or noxious fumes may exist. Keep work designed.
area well lighted.
Like all machines there is danger associated No list of safety guidelines can be complete.
with the Model G1067Z. Accidents are fre- Every shop environment is different. Always
quently caused by lack of familiarity or fail- consider safety first, as it applies to your
ure to pay attention. Use this machine with individual working conditions. Use this and
respect and caution to lessen the possibility other machinery with caution and respect.
of operator injury. If normal safety precau- Failure to do so could result in serious per-
tions are overlooked or ignored, serious sonal injury, damage to equipment, or poor
personal injury may occur. work results.
-4- G1067Z Wood Lathe
SECTION 1: INTRODUCTION
Most importantly, we stand behind our machines.
Commentary If you have any service questions or parts
requests, please call or write us at the location
listed below.
The Model G1067Z Wood Lathe is shipped from After all the parts have been removed from the
the manufacturer in a carefully packed carton. If carton, you should have:
you discover the machine is damaged after
you’ve signed for delivery, please call Customer • Main Lathe Unit
Service immediately for advice. • Grizzly Paddle Switch
• Front/Rear Covers
Save the containers and all packing materials for • Index Pin
possible inspection by the carrier or its agent. • 6'' Face Plate
Otherwise, filing a freight claim can be difficult. • 12'' Tool Rest
• Tool Rest Support
When you are completely satisfied with the con- • Tool Rest Extension
dition of your shipment, you should inventory its • Knock Out Bar
parts. • Stand Legs (4)
• Stand Support, Long (2)
• Stand Support, Short (2)
• Upper Mount Plate (2)
• End Stand Support (2)
The G1067Z represents
a load of 179 pounds. Fasteners:
Seek assistance before
beginning assembly. • Carriage Bolt 5⁄16"- 18 x 3⁄4" 24
• Flat Washer 5⁄16" 24
• Cap Screw 5⁄16"- 18 x 1" 8
• Hex Nut 5⁄16"- 18 32
• Phillips Head Screw 10 - 24 x 3⁄8" 12
Some metal parts may • Lock Washer 5⁄16" 8
have sharp edges on
them after they are In the event that any non proprietary parts are
formed. Please examine missing (e.g. a nut or a washer...), we would be
the edges of all metal glad to replace them, or, for the sake of expedi-
parts before handling ency, replacements can be obtained at your local
them. Failure to do so hardware store.
could result in injury.
NOTICE
The wire on the power cord with green or
green and yellow striped insulation is the
grounding conductor.
Pre-assembly Stand
Assembly of the G1067Z is straightforward. We 1. Locate all four stand legs and the two end
have organized the assembly process into steps. panels. Attach an end panel to any two of the
Please follow them in sequence. legs using the 10-24 x 3⁄8'' Phillips head
screws provided (Figure 1). Repeat this step
Tools Required: Only a few common tools are for the remaining end panel/legs. DO NOT
needed to assemble this machine. Specifically, a final tighten the bolts at this time.
6" adjustable wrench, 12mm open end wrench,
regular and Phillips head screwdriver and an
8mm Hex wrench.
Figure 1.
2. Bolt the upper mount plate and the short
Wear safety glasses dur-
stand support to each end assembly using
ing the entire set up
the 5⁄16''-18 x 3⁄4'' carriage bolts provided
process!
(Figure 2).
Figure 2.
Figure 3.
Figure 5.
Figure 4.
Figure 6.
Figure 8.
Figure 7.
Tailstock
The G1067Z is supplied with a #2 Morse taper The G1067Z is supplied with a 6'' face plate.The
spur center for use when spindle turning. The faceplate is used for bowl and plate turning.
spur center is used in conjunction with the tail- Install the face plate by threading the face plate
stock live center. Install the spur center by insert- onto the inboard spindle. Use the indexing pin to
ing into the hole in the inboard spindle (Figure hold the spindle from rotating while tightening
10). down or removing the face plate (Figure 12). DO
NOT use the face plate in conjunction with the
spur center. Mount your workpiece to the face
plate using the mounting holes bored into the
face plate.
Figure 10.
Headstock
Set pin
Figure 13.
Figure 15.
Figure 18.
Lock handle
Speed selector
Figure 19.
Figure 20.
Figure 22.
To mount a workpiece between centers:
Make sure the live center in the tailstock
1. Locate the center point on both ends of the lines up with the spur center in the head-
workpiece by carefully drawing diagonal stock before turning anything between
lines from corner to corner. The point of inter- centers. Failure to observe this step could
section is the center of the work. Find the result in the workpiece being thrown from
center of round wood stock by using a center the lathe. Serious personal injury may
finder instrument. occur.
2. When turning stock with a diameter greater 6. Line up the live center with the workpiece
than 2", remove the corner length edges with center. Turn the handwheel to press the
a hand plane or similar operation. DO NOT point of the live center into the workpiece.
attempt to “round” square stock in the lathe. Note—With dense wood, drill a hole at the
Serious personal injury many occur. center and score lines with a saw blade for
the live center.
3. Hold the spindle vertically and support it on a
solid surface. Line up the spur center with
the center of the workpiece. Drive the spur
center into the stock about 1⁄4" using a dead Do not press too firmly or the bearings will
blow hammer. Be careful not to split the bind and overheat. Likewise, do not adjust
workpiece. See Figure 23. Wood with splits too loosely or the workpiece will spin off
along the grain may fly off during the opera- the lathe. Use good judgement. Serious
tion. Note—With dense wood, drill a hole at personal injury could result if care is not
the center and score lines with a saw blade taken.
for the spur center. 7. Lock the tailstock in place.
Outboard turning is usually done when stock The headstock spindle indexes every 15˚ by
diameter is greater than 12''. For the size of this inserting the indexing pin into one of the holes in
particular lathe and its minimum turning speed, the headstock. Indexing is desirable when locking
we recommend a maximum diameter of 17'' and the workpiece in position such as when routing
a maximum thickness of 2''. flutes. The spindle is drilled every 30˚ and the
headstock housing has two holes that are drilled
Figure 24 depicts the lathe setup at 90˚ for turn- 15˚ apart. To index the spindle:
ing a bowl using the tool rest extension supplied.
1. Insert the pin through the hole in the hous-
Figure 25 depicts the lathe setup at 180˚ for turn- ing.
ing a bowl using a free standing tool rest (not sup-
plied). 2. Rotate the spindle by hand until the pin
drops into a hole in the spindle (Figure 26).
Indexing pin
General Lubrication
2. Worn switch.
Bed
Figure 27.
The following pages contain general machine We recommend you keep a copy of our current
data, parts diagram, parts list and Warranty/Return catalog for complete information regarding
information for your Model G1067Z Lathe. Grizzly's warranty and return policy. If you need
additional technical information relating to this
If you need parts or help in assembling your machine, or if you need general assistance or
machine, or if you need operational information, replacement parts, please contact the appropri-
we encourage you to call the appropriate region- ate regional Service Department listed in the
al Service Department. Our trained service tech- introduction.
nicians will be glad to help you.
Additional information sources are necessary to
If you have comments dealing specifically with realize the full potential of this machine. Trade
this manual, please write to our Bellingham, journals, woodworking magazines, and your local
Washington location using the address in the library are good places to start.
Introduction. The specifications, drawings, and
photographs illustrated in this manual represent
the Model G1067Z as supplied when the manual
was prepared. However, due to Grizzly’s policy of Like all power tools, there is danger asso-
continuous improvement, changes may be made ciated with the Model G1067Z Lathe. Use
at any time with no obligation on the part of the tool with respect and caution to lessen
Grizzly. Whenever possible, though, we send the possibility of mechanical damage or
manual updates to all owners of a particular tool operator injury. If normal safety precau-
or machine. Should you receive one, add the new tions are overlooked or ignored, serious
information to this manual and keep it for refer- personal injury may occur.
ence.
NOTICE
Modifications or improper use of this tool
will void the warranty.
Overall Dimensions:
Including Stand ....................................................................453⁄4" H x 20" W x 583⁄4" L
Swing Over Bed........................................................................................................14"
Swing Over Gap ......................................................................................................17"
Distance Between Centers ......................................................................................40"
Shipping Weight ................................................................................................190 lbs.
Weight in Place ................................................................................................179 lbs.
Construction:
Bed ....................................................................................Precision Ground Cast Iron
Headstock ......................................................................................................Cast Iron
Stand ..................................................................................Pre-Formed Sheet Steel
Spindle....................................................Shielded & Lubricated-For-Life Ball Bearings
Specifications:
Spindle Size ..........................................................................................1" x 12 TPI RH
Bore Through Spindle .........................................................................................0.406"
Tailstock Taper ....................................................................................................MT #2
Spindle Taper..................................................................................MT #2 Spur Center
Number ⁄ Range of Speeds ..........................................................6 ⁄ 500 to 2700 RPM
Motor:
Type ............................................................................TEFC Capacitor Start Induction
Horsepower ..........................................................................................................1⁄2 HP
Phase ⁄ Cycle ..............................................................................Single Phase ⁄ 60 Hz
Voltage ..................................................................................................................110V
Amps ..........................................................................................................................8
RPM ......................................................................................................................1720
Bearings ................................................Shielded & Lubricated-For-Life Ball Bearings
Switch ..................................................................................Safety Key Toggle Switch
Standard Features:
..................................................................................................................Swivel Head
................................................................................................................6" Face Plate
........................................................................................Articulated Tool Rest Support
59
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, spe-
cial, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the car-
ton. We will not accept any item back without this number. Proof of purchase must accompany the mer-
chandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
WARRANTY CARD
Name ____________________________________________________________________________________
Street ____________________________________________________________________________________
City ______________________________________________________________State________Zip_________
Phone Number_______________________E-Mail_______________________FAX________________________
MODEL #_____________________Serial # __________________________ Order #______________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of
course, all information is strictly confidential.
___Other__________________________________________________ __________________________________________________________
4. What is your annual household income? __________________________________________________________
___$20,000-$29,999 ___$60,000-$69,999 14. What new accessories would you like Grizzly Industrial to carry?
___$30,000-$39,999 ___$70,000-$79,999
___$40,000-$49,999 ___$80,000-$89,999 __________________________________________________________
___$50,000-$59,999 ___$90,000 +
__________________________________________________________
5. What is your age group?
15. What other companies do you purchase your tools and supplies from?
___20-29 ___50-59
__________________________________________________________
___30-39 ___60-69
___40-49 ___70 + __________________________________________________________
6. How long have you been a woodworker? 16. Do you think your purchase represents good value?
Place
Stamp
Here
Name_______________________________
Street_______________________________
City______________State______Zip______
• SECURE ORDERING
• ORDERS SHIPPED WITHIN 24 HOURS
• E-MAIL RESPONSE WITHIN ONE HOUR
-OR-