Professional Documents
Culture Documents
SNV 2020
SNV 2020
SNV 2020
Emergency-Stop Relay
Basic Unit
According to EN 60204 - 1 and EN 954 - 1
Single or Dual Channel E-Stop are Possible
3 Non-Delayed, 1 Off-Delayed Enabling Current Paths
SNV 2020 EN 60204 --1 For Stop Category 0/1
With /Without RESET Monitoring
EN 954 --1 Safety Category 4/3
Rated Voltage in the E-Stop Control Circuit: 24 V DC
+ + +
60
75
K2
104,5
K1
4,5
K4
-- +
K5
80 5
82,5 108,5
90
K1 K2 K4 K3 K5
1.48
Relays and Automation Systems
Safety Switching Devices
SNV 2020-17
Single-Channel E-Stop Circuit without/with* RESET Monitoring Dual Channel E-Stop Circuit with RESET monitoring
L+ L+
E-Stop E-Stop
A1 A2 Y1
+
Y2 S12 S12
+ +
A1 S11 S12 S12 S22 13 23 33 41 57
+ +
K3
A1 A2 Y1 Y2 S12 S12
+ + +
A1 S11 S12 S12 S22 13 23 33 41 57
+ +
K3
1
K2 K2
K1 K1
K4 K4
-- + -- +
K5 K5
K1 K2 K4 K3 K5 K1 K2 K4 K3 K5
M
M The dual channel E-Stop circuit switches off even if one of the two contacts of
The single channel E-Stop circuit complies with the requirements acc. to the E-Stop button does not open . If a fault occurs (e.g. the E-Stop contact
EN 60204 - 1. The E-stop circuit offers however no redundancy. When connected to S22 does not open), the safety circuit is activated by the second
the RESET switch is connected to the terminal Y2 (without RESET (redundant) contact S12. The enabling current paths 13/14, 23/24 and
monitoring), the unit can be enabled by actuating the RESET switch. 33/34 open. In case of short circuit to GND of the cables connected to the
Ground faults in the RESET circuits will be detected. E-Stop switch, the voltage present at S11/S33 is short circuited. The relays K2,
K3 and off-delayed K4,K5 switch back into their off-position and the PTC
switches off the short-circuit current after 3s. The RESET switch is monitored; i.e.
Application Example A 1090 the device is enabled only by releasing the switch (with the falling edge of the
RESET switch). If the RESET switch is closed before the supply is applied to
External Contact Expansion with RESET Monitoring terminals S12 and S22 or there is a short circuit in the cable, the enabling current
and Premature Time Reset paths remain open. If however, a short circuit in the RESET cable occurs when
L+ the Emergency-Stop Relay is already active the cyclic self checking feature of the
item will detect it when switching the supply OFF/ON. As a consequence, the
Control
E-Stop enabling current paths will not close and the safety function is guaranteed.
Time-Reset
Uext
A1 S11 S12 S12 S22 13 23 33 41 57 Application Example A 1092
A1 A2 Y1 Y2 S12 S12 + +
K4
-- + Sliding
K5 Safety-Gate
closed
K1 K2 K4 K3 K5
+ + + K3
RESET
K2
K6
K1
Feedback Circuit
K4
K7 -- +
K5
M
If the number of enabled current paths is not sufficient, two external K1 K2 K4 K3 K5
contactors can be used for expansion. They are driven through one of the S11 S33 S34
enabling current paths of the SNV 2020-17. The function of the external S33 S34 Y1 Y2 14 24 34 42 58 A2
contactors is monitored by their own NC contacts connected in series to
the relay K1 (Y2). The contactors K6 and K7 must have positively guided RESET Feedback Circuit
contacts.
In order to match the off-delay time of the enabling current path 57/58
M
to the process cycle time, the off delay time can prematurely be set to 0
by switching off the supply voltage at A1. The position of the safety sliding gate is monitored through channel 1 (S12)
and channel 2 (S22). The SNV 2020-17 is activated through the RESET switch.
If the sliding safety gate opens, the Emergency-Stop Relays returns to its off-
position.The enabling current paths 13/14, 23/24, 33/34 open. If the safety
gate is closed again the Emergency-Stop Relay can be activated again through
the RESET switch.
1.49
Relays and Automation Systems
Safety Switching Devices
OUTPUT CIRCUIT
Contact Equipment 3 N.O. Safety Contact
Stop-/Safety Category 0/4
1 N.O. Safety Contact
Off - Delayed
Stop-/Safety Category 1/3
1 N.C. Control Contact
Contact Type Forced Contact
Contact Material Ag - Alloy; Gold - Plated
Switching Voltage Un V AC/DC 230/230
Maximum Rated Current In per Contact A 6
Maximum Total Current for all Contacts A 18
Application Category According To EN 60947--5--1:1991 AC--15: Ue 230 V AC, Ie 4 A
DC--13: Ue 24 V DC, Ie 6 A
Short-Circuit Protection, Max. Fuse Element Class gG A 6
Permissible Switching Frequency Switching Cycle/h 3600
Mechanical Lifetime Switching Cycle 30 x 106
GENERAL DATA
Creepage and Clearance Distances Between Circuits
According to DIN VDE 0110 - 1:04.97: Rated Withstand Voltage kV 4
Over-Voltage Category III
Contamination Level 3 Outside 2 Inside
Design Voltage V AC 300
Test Voltage Ueff 50 Hz acc. to DIN VDE 0110 - 1, Table A.1 kV 2,21
Protection Class Housing/Terminals acc. to DIN VDE 0470 Sec. 1:11.92 IP 40/IP 20
Radiated Noise EN 50081--1:03.93, --2:03.94
Noise Immunity EN 50082--2:1995
1.50 1.x
Relays and Automation Systems