Professional Documents
Culture Documents
Annex 2d-4648-C721-C1-Tanganda Weir Details
Annex 2d-4648-C721-C1-Tanganda Weir Details
Annex 2d-4648-C721-C1-Tanganda Weir Details
ARUP_PLOT_LABEL
Gabion Training Wall Notes
(See dwg C725) 1. To be read in conjunction with drawing C720,
B
C724, C725, C726 and C727.
Ø500mm Tanganda Gravity Pipe
2. Cement sand mortar ratio 1:6 for all masonry
work.
Abutment Wall 3. All concrete for dental works to be Grade 20.
11 5 deg Slope of Retained Fill G
4. Masonry construction is used for Spillways,
A 501m
0.5m weirs, headwalls , guide walls and other
See Detail 'A'
works as decided on each site.
2H:1V
Slope
2H:1V
Slope
Weir & Spillway (68m) Mod AASHTO
Gabion Foundation Matress batching proportions given on the drawings.
3H:4V
Slope
3H:4V
Slope
6. The masonry setting out should be done by a
suitably qualified and competent person and
2H:1V
Slope
498m to follow the design dimensions.
D 7. Bright oil paint is used to mark the outline,
A
bench levels and crest levels.
2 8. Stone for both aggregates and masonry
B should be hard undecomposed stone.
C Direction Of Flow 9. All Aggregates must be cleaned before they
Final Gabion 700 700 700 700 700 700 700 Rock Backfill
Earth Embankment can be used.
After Scour 1400 10. Water must be clean and free from dissolved
Crest of Weir Acting as Centre chemicals and suspended slime and organic
Spillway dims 68m Lenght x 3m Freebody material and where possible portable.
Gabion Bank Slope
Scale 1:50 11. River sand should be clean and well graded
14m
and where possible a 4.75mm sieve should
General Weir Plan View be employed to screen out all undesirable
Scale 1:500 1H:3V material mingled with it.
Slope 12. The construction mortar should be in the
3 proportion of 1 cement bag : 6 wheel
2H:1V
burrows sand and should be mixed on a level
non-porous surface or on polythene sheeting.
13. Only concrete or mortar that can be placed
within 15 mins of mixing should be prepared
0.5m per batch.
14. The surface to receive masonry should
505.00 roughened using a cold chisel and 2 pound
1H:3V
hammer before being thoroughly cleaned
Slope
5m 10m 5m using water and wire brushes.
15. A concrete slurry is applied to the surface
3.0m
1m
4 16. Construction stone must at all times be
Y Y
5m 10m 5m placed with the penetration thickness into
8.0m
0.5m
to 89% MOD AASHTO
must never be constructed standing on edge.
3 17. Masonry walls to be constructed according to
4m
1H:3V
1H:3V
3.0m
BS5390:1976.
Slope
Slope
Section Y-Y
18. Weir, spillway and abutment wall to be
Scale NTS
constructed monolithically.
Direction Of Flow
F F
1H:3V
498.00 2.3m 7m
0.5m
5
Detail A
G
Scale NTS Masonry Abutment Wall Plan
Section E-E
Scale 1:100
Scale 1:100 C1 13/06/22 KB PTC PTC
Issue For Construction
10% Settlement Allowance Decreasing Uniformly
to Zero at the Bottom of the Embankment Issue Date By Chkd Appd
7m
Selected and Hand Placed 200mm
4m
Homogeneous Earth Embankment 4m
and 100mm Dry Stone (Rip-rap). 0.5m
505.00
505.00
0.5m
6 505.00
Height of Embankment Varies
with Change in Ground Level
2 2
1 1
FSL
Block 1, First Floor, Arundel Office Park, Norfolk Road
Mount Pleasant, Harare
Tel+263 (04) 369111-17 Fax+263 (04) 369118
2 www.arup.com
1 1 1
Client
Ground Level Varies 1 3 3
3
2m
1 1
0.5 0.5
7 4m
Project
Varies
498.00
Typical Homogeneous Fill Embankment
Section A-A
498.00
Scale 1:200
Elevation F-F
Elevation G-G Scale 1:100
Scale 1:100
Earth Embankment
4m
Selected and Hand Placed 200mm
Cement Grout
2
2 Masonry Abutment Gabion Training Wall
Existing Ground Level. 1
1 (See dwg C725)
1 4 1
0.5 0.5
Foundation Level
0.8m
4m
9 Dental Concrete
Section B-B (CH 0+068) Max 150mm Thick
Scale 1:200
1m
Max 0.15m
0.300 0.300
FSL Cill Crest Level 502m
Job Title
0.8m
See Detail 'A' dwg C724 Cement Grout
0.150
See dwg C727
Masonry Weir Cill UNOPS Mutema Irrigation
Rehabilitation
4m
0.300
See Detail 'X' dwg C725
Existing 3 Existing
0.150
FSL Cill Crest Level 502m 4 Ø20mm High Yield
River Invert Level 498m River Invert Level 498m River Invert Level 498m
10 Deformed Bars 0.300 0.300 0.300
3
Drawing Title
4
4m
3m
Scale 1:20
Estimated Bedrock Level 495m
Dental Concrete
Dowel Bar Plan View
Scale 1:10 Scale at A1
As Shown
Notes:
Dental Concrete Discipline
Masonry Weir 1. After exposing fresh rock, drill dia 20mm holes Civils
Section D-D 0.5m deep. Then place in cement grout before Drawing Status
11 Earth and Concrete Abutment
Scale 1:150 placing dowel bars as shown.
Section C-C Construction
2. Construct dowel bars along length of L-shaped
Scale 1:200
abutment wall and weir. Job No Drawing No Issue
3. Apply dental concrete to foundation levels.
4648 C721 C1