Professional Documents
Culture Documents
Asme Sec Iii D1 ND-1000 - 2004
Asme Sec Iii D1 ND-1000 - 2004
INTRODUCTION
(c) Subsection ND does not contain rules to cover all (a) valve guides, thermal sleeves, and turning
details of construction of Class 3 vessels and storage vanes;
tanks. Where complete details are not provided in this (b) vessel saddles, support and shear lugs, brack-
Subsection, it is intended that the Certificate Holder, sub- ets, pipe clamps, trunnions, skirts, and other items within
ject to the approval of the Owner or his designee and the component support load path.
acceptance by the Inspector, shall provide details of con- (c) Attachments will also have either a structural or
struction which will be consistent with those provided nonstructural function.
by the rules of this Subsection. (1) Attachments with a structural function (struc-
tural attachments):
(a) perform a pressure retaining function;
(b) are in the component support load path.
ND-1130 BOUNDARIES OF JURISDICTION (2) Attachments with a nonstructural function (non-
APPLICABLE TO THIS structural attachments):
SUBSECTION
(a) do not perform a pressure retaining function;
ND-1131 Boundary of Components (b) are not in the component support load path;
(c) will be permanent or temporary.
The Design Specification shall define the boundary of Nonstructural attachments include items such as name-
a component to which piping or another component is plates, insulation supports, and locating and lifting lugs.
attached. The boundary shall not be closer to a vessel,
tank, pump, or valve than: ND-1132.2 Jurisdictional Boundary. The jurisdic-
tional boundary between a pressure retaining component
(a) the first circumferential joint in welded connec-
and an attachment defined in the Design Specification
tions (the connecting weld shall be considered part of the
shall not be any closer to the pressure retaining portion
piping); of the component than as defined in (a) through (g) below.
(b) the face of the first flange in bolted connections Figures ND-1132.2-1 through ND-1132.2-3 are provided
(the bolts shall be considered part of the piping); as an aid in defining the boundary and construction
(c) the first threaded joint in screwed connections. requirements of this Subsection.
(a) Attachments cast or forged with the component retaining material. Beyond 2t from the pressure retaining
and weld buildup on the component surface shall be portion of the component, the first weld shall be consid-
considered part of the component. ered part of the attachment.
(b) Attachments, welds, and fasteners having a pres- (e) The first connecting weld of a welded nonstructural
sure retaining function shall be considered part of the attachment to a component shall be considered part of
component. the attachment. At or within 2t from the pressure retaining
(c) Except as provided in (d) and (e) below, the bound- portion of the component the first connecting weld shall
ary between a pressure retaining component and an conform to ND-4430.
attachment not having a pressure retaining function shall (f) Mechanical fasteners used to connect a nonpres-
be at the surface of the component. sure-retaining attachment to the component shall be con-
(d) The first connecting weld of a nonpressure- sidered part of the attachment.
retaining structural attachment to a component shall be (g) The boundary may be located further from the
considered part of the component unless the weld is more pressure retaining portion of the component than as
than 2t from the pressure retaining portion of the compo- defined in (a) through (f) above when specified in the
nent, where t is the nominal thickness of the pressure Design Specification.
2
--```,,,`,`,,``,`,`,,,``,`,,`,-`-`,,`,,`,`,,`---
--```,,,`,`,,``,`,`,,,``,`,,`,-`-`,,`,,`,`,,`---
FIG. ND-1132.2-2 ATTACHMENTS WHICH DO NOT PERFORM A PRESSURE RETAINING FUNCTION AND
ARE NOT IN THE COMPONENT SUPPORT LOAD PATH (NONSTRUCTURAL
ATTACHMENTS)
--```,,,`,`,,``,`,`,,,``,`,,`,-`-`,,`,,`,`,,`---