Professional Documents
Culture Documents
Nissan E25
Nissan E25
K ELECTRICAL
B
SECTION
LIGHTING SYSTEM C
E
CONTENTS
PRECAUTION ............................................................ 2 LIGHTING AND TURN SIGNAL SWITCH ................ 18 F
Precautions for Supplemental Restraint System Removal and Installation ........................................ 18
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN- Switch Circuit Inspection ........................................ 18
SIONER” .................................................................. 2 HAZARD SWITCH .................................................... 19 G
Precaution ................................................................ 2 Removal and Installation ........................................ 19
Wiring Diagrams and Trouble Diagnosis .................. 2 PARKING, LICENSE AND TAIL LAMPS .................. 20
HEADLAMP ................................................................ 3 Wiring Diagram — TAIL/L — .................................. 20
H
System Description .................................................. 3 Bulb Replacement .................................................. 22
Wiring Diagram — H/LAMP — ................................. 4 Removal and Installation ........................................ 22
Trouble Diagnoses ................................................... 5 BACK-UP LAMP ....................................................... 23
Aiming Adjustment ................................................... 5 Wiring Diagram — BACK/L — ................................ 23 I
Bulb Replacement .................................................... 6 Bulb Replacement .................................................. 24
Removal and Installation .......................................... 7 Removal and Installation ........................................ 24
FRONT FOG LAMP .................................................... 8 REAR COMBINATION LAMP ................................... 25 J
System Description .................................................. 8 Wiring Diagram —STOP/L— .................................. 25
Wiring Diagram — F/FOG — ................................... 9 Bulb Replacement .................................................. 26
Aiming Adjustment ................................................. 10 Removal and Installation ........................................ 26
LT
Bulb Replacement .................................................. 10 INTERIOR ROOM LAMP .......................................... 27
Removal and Installation .........................................11 Wiring Diagram —ROOM/L— ................................ 27
TURN SIGNAL AND HAZARD WARNING LAMPS... 12 Bulb Replacement .................................................. 34
System Description ................................................ 12 Removal and Installation ........................................ 35 L
Wiring Diagram — TURN — .................................. 14 ILLUMINATION ......................................................... 36
Trouble Diagnoses ................................................. 16 System Description ................................................. 36
Electrical Components Inspection .......................... 16 Wiring Diagram — ILL — ........................................ 37 M
Bulb Replacement .................................................. 16 ASHTRAY ILLUMINATION ....................................... 39
Removal and Installation for Side combination Wiring Diagram ....................................................... 39
Lamp ...................................................................... 17 Bulb Replacement Removal and Installation .......... 39
Removal and Installation for Rear Turn Signal Lamp... 17
LT-1
PRECAUTION
PRECAUTION PFP:00011
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER” EKS002YC
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
● To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
● Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
● Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow harness connector.
Precaution EKS002QG
● Do not touch the glass of bulb directly by hand. Keep grease and other oily matters away from it. Do not
touch bulb by hand while it is lit or right after being turned off. Burning may result.
● Do not leave bulb out of headlamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of the headlamp. When replacing the bulb, be sure to replace it with a new one.
● Adjust aiming by tightening aiming screw. (To adjust it toward loosening side, first loosen adjusting screw,
and then make adjustment by tightening.)
● To remove soil or sealant of bulbs, do not use organic solvent (thinner, gasoline, etc.)
● When replacing bulb, be sure to hold bulb socket and pull it out straight. If wiring harness of the bulb is
pulled at an angle, the bulb may be caught in the lamp, making it difficult to take out.
Wiring Diagrams and Trouble Diagnosis EKS002YD
LT-2
HEADLAMP
HEADLAMP PFP:26010
A
System Description EKS002QI
DESCRIPTION
The headlamps are controlled by the lighting switch which is built into the combination switch. B
Power is supplied at all times
● to lighting switch terminal 8
● through 15A fuse (No. 44, located in the fuse and fusible link box), and C
● to lighting switch terminal 5
● through 15A fuse (No. 41, located in the fuse and fusible link box).
LOW BEAM OPERATION D
When the lighting switch is turned to the 2ND position and placed in LOW (“B”) position, power is supplied
● from lighting switch terminal 10
E
● to terminal 1 of the headlamp LH, and
● from lighting switch terminal 7
● to terminal 1 of the headlamp RH. F
Terminal 3 of each headlamp supplies ground through body grounds H7 and H18.
With power and ground supplied, the low beams will illuminate.
HIGH BEAM OPERATION/FLASH-TO-PASS OPERATION G
When the lighting switch is turned to the 2ND position and placed in HIGH (“A”) position or PASS (“C”) posi-
tion, power is supplied
● from lighting switch terminal 6 H
● to terminal 2 of headlamp RH, and
● from lighting switch terminal 9
I
● to terminal 2 of headlamp LH, and
● to combination meter terminal 48(with tachometer) or 42(without tachometer) for the HIGH BEAM indica-
tor.
J
Ground is supplied to terminal 49(with tachometer) or 41(without tachometer) or of the combination meter
through body grounds M2 and M27.
Ground is supplide to terminal 3 of each headlamp through body grounds H7 and H18.
With power and ground supplied, the high beams and the HIGH BEAM indicator illuminate. LT
LT-3
HEADLAMP
TKWH0008E
LT-4
HEADLAMP
A
Symptom Possible cause Repair order
1. Check bulb.
1. Bulb 2. Check grounds H7 and H18. B
2. Grounds H7 and H18 3. Check 15A fuse (No. 44, located in fuse
Headlamp LH do not operate. and fusible link box). Verify battery posi-
3. 15A fuse
tive voltage is present at terminal 8 of
4. Lighting switch C
lighting switch.
4. Check lighting switch.
1. Check bulb.
D
1. Bulb 2. Check grounds H7 and H18.
2. Grounds H7 and H18 3. Check 15A fuse (No. 41, located in fuse
Headlamp RH do not operate. and fusible link box). Verify battery posi-
3. 15A fuse E
tive voltage is present at terminal 5 of
4. Lighting switch lighting switch.
4. Check lighting switch.
F
1. Check bulbs.
1. Bulb 2. Check the wire between lighting switch
High beam LH do not operate, but low
2. Open in high beam LH circuit terminal 9 and headlamp LH terminal 2
beam LH operates. G
3. Lighting switch for an open circuit.
3. Check lighting switch.
1. Check bulb.
1. Bulb H
2. Check the wire between lighting switch
Low beam LH does not operate, but high
2. Open in low beam LH circuit terminal 10 and headlamp LH terminal 1
beam LH operates.
3. Lighting switch for an open circuit.
3. Check lighting switch. I
1. Check bulbs.
1. Bulb 2. Check the wire between lighting switch
High beam RH do not operate, but low J
2. Open in high beam RH circuit terminal 6 and headlamp RH terminal 2
beam RH operates.
3. Lighting switch for an open circuit.
3. Check lighting switch.
1. Check bulb.
LT
1. Bulb 2. Check the wire between lighting switch
Low beam RH does not operate, but high
2. Open in low beam RH circuit terminal 7 and headlamp RH terminal 1
beam RH operates.
3. Lighting switch for an open circuit. L
3. Check lighting switch.
1. Check bulb in combination meter.
2. Check grounds M2 and M27.
M
1. Bulb
High beam indicator does not work. 2. Grounds M2 and M27 3. Check the wire between lighting switch
terminal 9 and combination meter termi-
3. Open in high beam circuit
nal 42(without tachometer) or 48(with
tachometer) for an open circuit.
When performing headlamp aiming adjustment, use an aiming machine, aiming wall screen or headlamp
tester. Aimers should be in good repair, calibrated and operated in accordance with respective operation man-
uals.
If any aimer is not available, aiming adjustment can be done as follows:
For details, refer to the regulations in your own country.
● Keep all tires inflated to correct pressures.
● Place vehicle and tester on one and same flat surface.
● See that there is no-load in vehicle (coolant, engine oil filled up to correct level and full fuel tank) other
than the driver (or equivalent weight placed in driver's position).
LT-5
HEADLAMP
LOW BEAM
1. Turn headlamp low beam on.
SKIA0798E
If the vehicle front body has been repaired and/or the headlamp assembly has been replaced, check aim-
ing. Use the aiming chart shown in the figure.
● Adjust headlamps so that main axis of light is parallel to cen-
ter line of body and is aligned with point P shown in illustra-
tion.
● Figure to the left shows headlamp aiming pattern for driv-ing
on right side of road; for driving on left side of road, aiming
pattern is reversed.
● Dotted lines to point P in illustration show center of head-
lamp.
"H" : Horizontal center line of headlamps
"WL : Distance between each headlamp center
"
"L" : 5,000mm (196.85 in)
"C" : 65mm (2.56 in)
● Basic illuminating area for adjustment should be within the
range shown at left. Adjust headlamps accordingly.
SEL254L
HEAD LAMP
1. Remove the headlamps. Refer to LT-7, "Removal and Installation"
2. Disconnect connector of headlamp.
3. Remove rubber cap.
4. Unlock retaining spring, then remove bulb.
Headlamp (High/Low) : 12V 60/55 W(H4)
SKIA0408E
CLEARANCE LAMP
1. Remove the headlamps. Refer to LT-17, "Removal and Installation for Side combination Lamp"
LT-6
HEADLAMP
REMOVAL
1. Remove the sidecombination lamps. Refer to LT-17, "Removal E
and Installation for Side combination Lamp"
2. Remove the front grille. Refer to EI-12, "FRONT GRILLE" in
"EXTERIOR & INTERIOR (EI)" section. F
3. Remove the headlamp mounting bolts.
4. Pull the headlamp toward the front of the vehicle.
G
SKIA0409E H
INSTALLATION
● Install in the reverse order of removal, taking care of the following points.
Headlamp mounting screws and nut I
LT
LT-7
FRONT FOG LAMP
DESCRIPTION
Power is supplied at all times to fog lamp relay terminal 5
● through 15A fuse (No. 46, located in the fuse and fusible link box).
With the lighting switch in the 2ND position and LOW (“B”) position, power is supplied
● through 10A fuse (No. 43, located in the fuse and fusible link box).
● to lighting switch terminal 11
● through terminal 12 of the lighting switch
● to fog lamp relay terminal 1.
FOG LAMP OPERATION
The fog lamp switch is built into the combination switch. The lighting switch must be in the 1st or 2nd position
and LOW (“B”) position for fog lamp operation.
With the fog lamp switch in the ON position, ground is supplied
● to fog lamp relay terminal 2
● through the fog lamp switch and body grounds M27 and M2.
The fog lamp relay is energized and power is supplied
● from fog lamp relay terminal 3
● to terminal 1 of each fog lamp.
Ground is supplied to terminal 2 of each fog lamp through body grounds M49, M121 and D2.
With power and ground supplied, the fog lamps illuminate.
LT-8
FRONT FOG LAMP
LT
TKWH0013E
LT-9
FRONT FOG LAMP
1. Set the distance between the screen and the center of the fog
lamp lens as shown at left.
2. Remove front fog lamp rim. For detail, refer to “BODY END” in
BT section.
3. Turn front fog lamps ON.
MEL327G
4. Adjust front fog lamps so that the top edge of the high intensity
zone is 100 mm (4 in) below the height of the fog lamp centers
as shown at left.
● When performing adjustment, if necessary, cover the head-
lamps and opposite fog lamp.
MEL328G
LT-10
FRONT FOG LAMP
SKIA0626E
D
Removal and Installation EKS002QS
REMOVAL
1. Remove fog lamp mounting screw (2).
E
2. Pull out fog lamp from vehicle and disconnect connector.
SKIA0413E
H
INSTALLATION
● Install fog lamp in the reverse order of removal, observing the tightening torque shown below.
Fog lamp mounting screw I
Tightening torque :4.5 - 6.4 N-m (0.45 - 0.65 kg-m, 39 - 56 in-lb)
LT
LT-11
TURN SIGNAL AND HAZARD WARNING LAMPS
LT-12
TURN SIGNAL AND HAZARD WARNING LAMPS
LT
LT-13
TURN SIGNAL AND HAZARD WARNING LAMPS
TKWH0014E
LT-14
TURN SIGNAL AND HAZARD WARNING LAMPS
LT
TKWH0015E
LT-15
TURN SIGNAL AND HAZARD WARNING LAMPS
SEL122E
1. Remove the side combination lamp. Refer to LT-17, "Removal and Installation for Side combination Lamp"
LT-16
TURN SIGNAL AND HAZARD WARNING LAMPS
SKIA0426E
D
Removal and Installation for Side combination Lamp EKS002QY
REMOVAL
1. Loosen screws (1), then pull the side combination lamp toward
the front of the vehicle. E
SKIA0414E
H
INSTALLATION
● Install side combination lamp in the reverse order of removal.
I
Removal and Installation for Rear Turn Signal Lamp EKS002QZ
LT
LT-17
LIGHTING AND TURN SIGNAL SWITCH
SKIA0059E
Using circuit tester, check continuity between the lighting and turn
signal switch connector terminals in each operation status of the
switch.
Hi: “HIGH BEAM” position, Lo: “LOW BEAM” position, P: “FLASH
TO PASS” position
SKIA0695E
LT-18
HAZARD SWITCH
REMOVAL
1. Remove cluster lid C. Refer to IP-3, "INSTRUMENT PANEL
B
ASSEMBLY" .in “INSTRUMENT PANEL (IP)” section.
2. Using a flat-bladed screwdriver or other suitable tool, press pawl
to remove hazard switch from cluster lid C.
C
SKIA0418E
E
INSTALLATION
Installation is in the reverse order of removal.
F
LT
LT-19
PARKING, LICENSE AND TAIL LAMPS
TKWH0009E
LT-20
PARKING, LICENSE AND TAIL LAMPS
LT
TKWH0010E
LT-21
PARKING, LICENSE AND TAIL LAMPS
SKIA0427E
Installation
● Install license plate lamp in the reverse order of removal, observing the tightening torque shown below.
License plate lamp mounting screws
Tightening torque :1.0 - 1.8 N-m (0.10 - 0.19 kg-m)
LT-22
BACK-UP LAMP
LT
TKWH0012E
LT-23
BACK-UP LAMP
LT-24
REAR COMBINATION LAMP
LT
TKWH0011E
LT-25
REAR COMBINATION LAMP
SKIA0801E
SKIA0416E
REMOVAL
1. Remove the body side trim. Refer to EI-22, "BODY SIDE TRIM"
in “EXTERIOR & INTERIOR (EI)” section.
2. Disconnect the rear combination lamp connector.
3. Remove the rear combination lamp mounting bolts.
4. Pull the rear combination lamp toward rear of the vehicle and
remove from the vehicle.
5. Remove the harness from the vehicle.
SKIA0801E
INSTALLATION
Install in the reverse order of removal, taking care of the following points.
Rear combination lamp mounting bolt
: 4.5 - 6.4 (0.45 - 0.65, 39 - 59 in-lb)
LT-26
INTERIOR ROOM LAMP
LT
TKWH0020E
LT-27
INTERIOR ROOM LAMP
TKWH0021E
LT-28
INTERIOR ROOM LAMP
LT
TKWH0022E
LT-29
INTERIOR ROOM LAMP
TKWH0023E
LT-30
INTERIOR ROOM LAMP
LT
TKWH0024E
LT-31
INTERIOR ROOM LAMP
TKWH0025E
LT-32
INTERIOR ROOM LAMP
LT
TKWH0026E
LT-33
INTERIOR ROOM LAMP
SKIA0419E
SKIA0064E
SKIA0428E
LT-34
INTERIOR ROOM LAMP
SKIA0419E
2. Remove the interior room lamp mounting bolts and remove the interior room lamp. E
3. Disconnect the interior room lamp connector.
SPOT LAMP F
1. Using a clips driver or a suitable tool, press and remove the
metal clip of the spot lamp.
2. Disconnect the spot lamp connector. G
I
SKIA0064E
SKIA0428E M
LT-35
ILLUMINATION
ILLUMINATION PFP:00011
LT-36
ILLUMINATION
LT
TKWH0017E
LT-37
ILLUMINATION
TKWH0018E
LT-38
ASHTRAY ILLUMINATION
SKIA0492E
LT
LT-39
ASHTRAY ILLUMINATION
LT-40