Professional Documents
Culture Documents
AN002 homeLYnk Backward Compatibility Package
AN002 homeLYnk Backward Compatibility Package
Application note
homeLYnk backward compatibility
package for FW V1.1 and V1.0
The addition of either symbol to a “Danger” or “Warning” safety label indicates that an electrical hazard
exists which will result in personal injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible injury or death.
DANGER
WARNING
CAUTION
NOTICE
NOTICE is used to address practices not related to physical injury. The safety
alert symbol shall not be used with this signal word.
A qualified person is one who has skills and knowledge related to the construction, installation, and
operation of electrical equipment and has received safety training to recognize and avoid the hazards
involved.
Safety Precautions
WARNING
2.1 After upgrade your homeLYnk from FW V1.0, V1.1 to higher .............................................................. 7
2.2 For successful import of project created in FW V1.0, V1.1 to homeLYnk with higher FW version ........ 7
Once projects were created in homeLYnk firmware version 1.0 and 1.1, it needs to be considered that an
upgrade of the firmware of homeLYnk to version 1.2 or higher will be needed. Icons related to camera and to
graph will be incorrectly displayed. This backward compatibility firmware package will correct both types of
icons.
This application note describes how to install backward compatibility package for homeLYnk and under which
conditions it has to be used.
There is only one necessary competency to follow the procedures mentioned in this application note. All what
is needed to know are basic homeLYnk configuration skills described in the product manual.
Procedures contained in this application note were tested on the homeLYnk specified in Table 1.
FW version Note
Table 1: FW versions
has to be followed.
Backup made in V1.2.0 Not supported or upgrade firmware to 1.2 No action needed
only for an upgrade process, but also for expansion of existing projects to one or more other homeLYnks.
1) Go to homeLYnk
Firefox or Chrome can be used. Enter IP address of homeLYnk, which you want to Backup
2) Go to configurator
3) Click on backup
Web browser automatically starts to download homeLYnk backup. File-name of backup is based on data and
time.
1) Go to homeLYnk
Firefox or Chrome can be used. Enter IP address of homeLYnk, which you want to Restore
2) Go to configurator
3) Click on Restore
Wait for device reboot, for successful restore from backup file. Device is ready, when LED 1 is blinking and
LED 2 is steady on (It can take approximately 1 minute).
1.1, it needs to be considered that upgrade of the firmware of homeLYnk to version 1.2 or higher will be
required.
After each firmware upgrade homeLYnk will be completely erased, except the IP address, which will be
preserved
To secure the project it is necessary to use backup in configurator (More in chapter 3)
Default IP address (after HW factory reset) is unchanged – 192.168.0.10
From firmware version 1.2.0 and higher homeLYnk do not delete project during firmware upgrade. (we
strongly recommend backup homeLYnk every time for cases of failure power supply or other accidents)
This rule applies to initial firmware (firmware which you want to upgrade to a higher version) which is at
least V1.2.0 or higher
Default IP address (after HW factory reset) is unchanged – 192.168.0.10. There is one exception, if
homeLYnk will be upgraded from V1.0 or V1.1 to V1.2.0, your default IP address will be changed to the
IP address which your device had during upgrade.
Firefox or chrome can be used. Enter the IP address of homeLYnk, which you want to upgrade firmware
3) Go to System
4) Go to firmware upgrade
Wait for successful finish of upgrade. During firmware upgrade the device will not respond, because homeLYnk
will reboot several times. Device is ready, when LED 1 is blinking and LED 2 is steady on (It can take
approximately 5 minutes).
Download package from the PDF included in attachments, by clicking open attachments and right click to
2) Go to homeLYnk
Firefox or Chrome can be used. Enter the IP address of homeLYnk, where you want to install package
3) Go to Configurator
After displayed message “Update installed, device will reboot in 5 seconds” it will take approximately 1 minute
to reboot homeLYnk. Visualization of homeLYnk is ready, when the green LED 2 on the homeLYnk lights is
ON.
7) Check visualization
Head Office
35, rue Joseph Monier
92506 Rueil-Malmaison Cedex
FRANCE
www.schneider-electric.com