Professional Documents
Culture Documents
Trigger Cable Connection - Quick Guide
Trigger Cable Connection - Quick Guide
Trigger Cable Connection - Quick Guide
Original Manual
© 2021 This document or any part of it must not be translated, reproduced, or transmitted in any form or by any means, elec-
tronic or mechanical, including photocopying, recording, or by any information or retrieval system. Violations will be prose-
cuted. The use of general descriptive names, registered names, trademarks, etc. in this document does not imply, even in the
absence of a specific statement, that such names are exempt from the relevant protective laws and regulations and therefore
free for general use. Software programs will fully remain the property of ZEISS. No program, documentation, or subsequent up-
grade thereof may be disclosed to any third party, unless prior written consent of ZEISS has been procured to do so, nor may be
copied or otherwise duplicated, even for the customer's internal needs, apart from a single back-up copy for safety purposes.
ZEISS reserves the right to make modifications to this document without notice.
Content ZEISS
Content
1 Introduction .................................................................................. 4
4 Axiocam ........................................................................................ 8
5 ORCA-Flash/Fusion ........................................................................ 9
6 pco.edge ....................................................................................... 10
7 Prime BSI/95B................................................................................ 11
1 Introduction
Welcome Welcome to the quick guide for trigger cable connection.
This guide shows you how to connect the trigger cables to the camera and the SVB (signal distri-
bution box) in order to control the camera via external trigger.
Apart from the introduction and description pattern, each chapter represents one or more camera
models and its/their connections to the SVB.
Content
Chapter Content
Description Pattern Provides information on the description pattern of the sub-
sequent chapters.
2 Description Pattern
Each chapter describes the connections between one or more camera models and the SVB by fol-
lowing these patterns:
§ The right side represents the SVB and its ports (i.e. example 1).
Trigger OUT
Trigger IN 1
Trigger IN 2
Fig. 1: Example 1
§ The left side represents one camera and its specific ports (i.e. example 2).
Port 1
Trigger OUT
Port 2
Trigger IN 1
Port 3
Trigger IN 2
Port 4
Fig. 2: Example 2
§ If the camera needs a breakout cable, the left side represents the breakout cable and its indi-
vidual cables (i.e. example 3).
Cable 1
Trigger OUT
Cable 2
Cable 3
Cable 4 Trigger IN 1
Cable 5
Trigger IN 2
Fig. 3: Example 3
3 Andor iXon3
The following description is applicable for Andor iXon3 885 / 887 / 888 cameras.
Ext Trig
Trigger OUT
Arm
Trigger IN 1
Shutter
Trigger IN 2
Fire
4 Axiocam
The following description is applicable for these Axiocam cameras:
Axiocam SVB
TRIGGER
Trigger OUT
GPO 0
GPO 1
GPO 2 Trigger IN 1
GPOPWR
AUXPWR
Trigger IN 2
Fig. 5: Axiocam
5 ORCA-Flash/Fusion
The following description is applicable for ORCA-Flash4.0 and ORCA-Fusion cameras.
ORCA-Flash/Fusion SVB
EXT. TRIG
Trigger OUT
TIMING 1
Trigger IN 1
TIMING 2
Trigger IN 2
TIMING 3
6 pco.edge
The following description is applicable for pco.edge cameras.
pco.edge SVB
{
1
Trigger OUT
in
2
Trigger IN 1
{
3
out
Trigger IN 2
4
7 Prime BSI/95B
The following description is applicable for Prime BSI/95B cameras.
Trigger In
Trigger Ready Out Trigger OUT
Read Out
Expose Out 1
Expose Out 2 Trigger IN 1
Expose Out 3
Expose Out 4
Trigger IN 2