Professional Documents
Culture Documents
RBTHV5360
RBTHV5360
Description
The RBTHV5360 A and RBTHV5380 A are digital actua-
tors that operate on either 115 or 230 volt AC nominal power supply.
Both models deliver a minimum of 360 in.lb. or 40 Nm. torque at rated
voltage. The direction of rotation is reversible and the angle of rotation
may be mechanically limited. These actuators are equipped with the
patented Enerdrive System* which is an emergency operating device
that powers the actuator at full rated torque to its safety position. The
Enerdrive System may be used as the means of closure in 2 wire/2
position installations. The RBTHV5380 A is also equipped with 2
mechanical auxiliary switches.
Model Selection
RBTHV5360 A Digital Actuator for Line Voltage with the Enerdrive System
RBTHV5380 A Digital Actuator for Line Voltage with Enerdrive & Switches
Actuator Specifications
Power Supply 120VAC +/-10% or 240VAC +/-10%, 50-60 Hz
Selection by Slotted Slide Switch
Maximum Power Consumption 30VA at 120/240VAC Peak at Start-up
14VA at 120/240VAC Operating at Full Load
Number & Type of Auxiliary Switches RBTHV5380 A: 2 Mechanical, Fixed at 10° & 80°
Auxiliary Switch Rating 1 Amp Resistive, 24VAC
n e p t r o
3008-B 16TH AVE. W. SEATTLE, WA 98119
(800) 821-4863 (206) 282-4666
info@global-controls.net
n
(206) 282-4888 Fax
www.global-controls.net
c
RBTHV5360 A
Electronic Damper Actuators RBTHV5380 A
Dimensional Wiring
Schematic Schematics
A data sheet with more detailed dimensional All NEPTRONIC actuators with "HV" in the model name operate on line voltage power supply and
information and part nomenclature is avail- do not require a transformer. Multiple actuators may be wired in parallel as long as strict neutral/
able upon request. hot consistency is respected. Failure to do so will prevent the actuators from functioning.
RBTHV5360A FS DIR/REV
RBTHV5360A
FS DIR/REV
DIR/REV
RBTHV5380A DIR/REV
RBTHV5380A
2 Position Control Position Control
A Drive CW Drive CCW
Enerdrive CCW Enerdrive CW
D
DRIVE CCW
120VAC, 50-60 Hz
A
DRIVE CW
120VAC, 50-60 Hz
1.33 3.38 240VAC, 50-60 Hz 240VAC, 50-60 Hz
NEUTRAL
NEUTRAL
B 5.20 13.21
FS DIR/REV
RBTHV5360A FS DIR/REV
RBTHV5360A
RBTHV5380A RBTHV5380A
DIR/REV
C 9.13 23.19
3 Point Floating Control
DIR/REV
120VAC, 50-60 Hz
actuator. 240VAC, 50-60 Hz
120VAC, 50-60 Hz
240VAC, 50-60 Hz
NEUTRAL NEUTRAL
Dip Switch #1 controls the direction of rotation. For REVERSE acting, place the switch in the "ON" position; for
DIRECT acting, place the switch in the "OFF" position. Dip Switch #2 controls the Enerdrive direction. For Ener-
drive to operate in a CW direction, place the switch in the "ON" position; for a CCW direction, place the switch in
the "OFF" position. Dip Switch #3 has no function. Refer to the wiring diagrams for the interaction between switch
function and Enerdrive.
AUXILIARY SWITCHES
NATIONAL ENVIRONMENTAL PRODUCTS LTD., INC. MAINTAINS A POLICY OF CONTINUAL PRODUCT DEVELOPMENT; THEREFORE, IN THE INTEREST OF TECHNICAL
IMPROVEMENTS, THE FIRM RESERVES THE RIGHT TO CHANGE THE DESIGN, SPECIFICATIONS OR COMPONENTS OF THE EQUIPMENT WITHOUT PRIOR NOTICE.