Professional Documents
Culture Documents
CH880-01 SPC R223.1340-01
CH880-01 SPC R223.1340-01
CH880-01 SPC R223.1340-01
1340 en
SANDVIK CH880:01
This document is valid for:
SANDVIK CH880:01
Sandvik
Stationsplan, SE-233 81 Svedala, Sweden
Tel: +46 (0)40 409000, Fax: +46 (0)40 409260
www.sandvik.com
SPC Sandvik CH880:01 Table of contents
Contents Page
1. Cone crusher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
7a. Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8. V-belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8a. Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
17. Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
1. Cone crusher
1320-6
1320-5
1320-4
1320-3 1320-2 1320-1 1010-1
3, 4
5, 6
7505-3
7501-0
7503-0
7504-0
7502-0
7505-1,-2,-4
7505-0,-1,-2
7103-0
7103-1
7103-2
7102-0
7102-2
7102-4
7102-1 7104-0
7101-0
7100-0
The table below shows the segment support (cone) alternative with its matching rubber segments.
Cat. no. Qty. Part number Alternative Description Remarks
7100-0 6 442.9738-00 Segment support (cone) EC configuration
442.9740-00 C configuration
442.9739-00 MC configuration
7103-0 12 840.0069-00 Screw Fasteners for segment
supports
7103-1 24 847.0016-00 Washer
7103-2 12 845.0215-00 Lock nut
7104-0 4 840.0634-00 Screw M6S 16x25 Blind screw in topshell (when wearing
rubbers to filler ring are not used)
7101-0 12 442.9744-00 Rubber segment EC configuration
442.9746-00 C configuration
442.9745-00 MC configuration
Fasteners for rubber segments:
7102-4 48 873.1287-00 Rubber plug 4 plugs to each rubber segment
7102-0 48 840.0071-00 Screw M6S 16x55 4 screws to each rubber segment
7102-1 96 847.0016-00 Washer BRB 17x30 8 washer to each rubber segment
7102-2 48 845.0215-00 Lock nut M16 4 lock nuts to each rubber segment
3, 4, 5 16, 17, 18
6, 7, 8
19
21, 22, 25
20
23
24
12, 13, 14
15, 26
(Continued)
9, 10, 11, 12 17 7, 8
4, 5, 6
13
14 3
15
16
18, 19 20
18, 19 1
(Continued)
2, 3 1 4
8. V-belt drive
35, 36
33, 34
37, 38, 39
23
24, 25, 26
41 41
18
40
7 8, 9 1 4, 5, 6 2, 3
(Continued)
2, 3 5 1
A-A
Pos no Qty. Part number Alternative Description Remarks
458.0155-00 Sensor without speed monitor
1 1 458.0156-00 Bracket
2 2 840.0021-00 Screw M6S M8x20 8.8 fzb ISO 4017
3 2 847.0012-00 Washer BRB 8,4x16 ISO 7089
4 1 984.0217-00 Sensor SIH-3010-BPKG
2, 3
1
4
Pos no Qty. Part number Alternative Description Remarks
442.9650-00 Rubber compression mountings for crusher
01 1 864.0079-00 Damper SAW 300B
02 8 840.1135-00 Screw M6S 20x35 8.8 ISO 4017
03 8 847.0132-00 Washer BRB 21x36 HB200 SS 3576
04 2 442.5904-01 Fixing plate
6, 7
5
8
Pos no Qty. Part number Alternative Description Remarks
442.9874-91 Rubber compression mountings for crusher on subframe
05 2 864.0066-00 Damper SAW 300 A
06 8 840.1135-00 Screw M6S 20x35 8.8 ISO 4017
07 24 847.0132-00 Washer BRB 21x36 HB 200 ISO 3576
08 8 840.0078-00 Screw M6S 20x60 8.8 ISO 4017
10
18
04
U-U
37 17 (Q)
07 27
53 07
06 45 26 04
05 44 25
38 16 36 (T)
01 52
(Z)
22 23 24
(H)
U U
(N)
V
X (M)
02 03 21
19 20
18 54
11 15 X
12 15 (Y)
28 55
08 30 14
13 29 57
09 31 16
17
33 32 36
35
34
56 50 X-X
28 40
39 41
49 36
48 42 46
43
47
51
7 1
4 6 2
5 3 6
6 8 9
9 8 6
Pos no Qty Part number Alternative Description Remarks
452.3727-901 Over pressure blower unit, pneumatic droven
1 1 900.0180-00 Nipple ISO49 N8 1/2x1/4
2 1 912.0113-00 Air filter 504-2S 5 Micron
3 1 900.0169-00 Nipple 1/4 ISO 49 N8
4 1 902.0645-00 Regulator 216-2-8
5 1 900.0182-00 Nipple ISO 49 N8 3/4x1/4
6 2 900.1358-00 Clips 28 SMS 2298 Dy 23-27mm
7 1 819.0187-00 Pneumatic hose PVC 1”
8 2 900.1424-00 Hose coupling 3/
9 2 900.0275-00 Wrought iron pipe fittings socket 3/4”
(Continued)
17. Motor