Professional Documents
Culture Documents
Shuriken Datasheet
Shuriken Datasheet
Standard Shop
nut
High-strength polymer cap holds
nut and prevents it from rotating.
Washer
(optional)
To learn more, go to
atlastube.com/shuriken
DIMENSIONS AND AVAILABILITY
INSTALLATION PROCEDURE
3/4" SIZE SHOWN
Nut Shuriken
1 2 3
Washer
(3/4" only)
1. Insert a bolt and hand tighten with a nut (a washer may also be used for 3/4" bolts).
2. Place Shuriken over the nut and tack weld the steel ring to the substrate plate at all four corners.
3. Remove the bolt.
BOLTING CONFIGURATION
3/4" SIZE SHOWN
A325 or A490 bolt DTI washer and hardened washer Hardened washer Nut Shuriken
(PT or SC only*) (for 3/4" bolt; A490 PT
or SC only*)
*PT=Pretensioned; SC=Slip-critical. Use of washers complies with 2020 Specification for Structural Joints Using High-Strength Bolts by RCSC.
TECHNICAL NOTES
Codes and Standards be stored indoors in a sealed container Misaligned Installation and Drifting
Bolts installed with Shuriken are subject until the time of erection. If piece size Shuriken is designed to accommodate
to the codes and standards that govern or other circumstances prevent such misaligned bolts. In cases where
the project in which the bolts are storage, non-water soluble, corrosion- misalignment makes it difficult to engage
installed. The instructions and information inhibiting lubricant may be applied to the threads of the nut and bolt, a spud
presented here shall not be deemed to the nut threads at the time of Shuriken wrench or other means may be used to
waive or supersede any requirement of installation, and/or lubricant may be manually shift the nut and enclosing plastic
the governing codes and standards. applied to the bolts immediately prior to cap within the steel ring. When using
installation. Nuts installed within Shuriken Shuriken with large members, or in other
that are stored outdoors, in high humidity, cases where drifting forces are expected
Shuriken Attachment to be large, a dedicated hole for drifting in
or for long periods should be protected
Tack welds attaching Shuriken to the addition to the bolt holes is suggested to
from water, dust and other particulates
substrate material must engage the prevent Shuriken from being dislodged by
to the greatest extent practical. All
full thickness of the steel ring for the drifting forces.
fastener assemblies shall undergo
full width of the reentrant corner at
preinstallation verification in accordance
the weld location. Electrodes shall be
with the Specification for Structural Joints Cyclically Loaded Elements
70 ksi, minimum. Shuriken does not When Shuriken is used with members
Using High-Strength Bolts, published
participate in the structural load path, by the Research Council on Structural designed for fatigue, within the protected
so the welds attaching Shuriken to the Connections (RCSC). zones of applicable seismic systems, or
structure are generally not subject to in any other case where tack welds may
special inspection. However, welds that affect the performance of the underlying
Surface Preparation
are undersized, of low strength, or of poor structures, Shuriken should be attached
Keep steel surfaces underlying Shuriken
quality may prevent bolts from being to a mounting plate independent of the
free of oil, grease or other materials.
pretensioned. underlying structural elements.
HSS Seams
Lubrication and Corrosion Protection When Shuriken is attached to plates
To ensure bolt assemblies can be properly connected to the interior of an HSS
pretensioned, take care to ensure proper member (e.g., HSS column splices), the
lubrication and prevent corrosion. When seam on the interior of the HSS member
practical, pieces such as splice plates shall be ground flat in locations where a
to which Shuriken is attached should plate will contact the seam.
Shuriken
4 within lower shaft.
atlastube.com/shuriken
ATU-061022