Professional Documents
Culture Documents
Waterstop RX Product Data 1693262
Waterstop RX Product Data 1693262
Waterstop RX Product Data 1693262
WATERSTOP-RX®
EXPANDING CONCRETE JOINT WATERSTOP
DESCRIPTION joints, new to existing concrete construction, skinning over and curing. CETSEAL may be
WATERSTOP-RX is a hydrophilic strip wa- irregular surfaces, and around through-wall applied to damp surfaces, but not in stand-
terstop designed to stop water iniltration penetrations, such as plumbing and utility ing water.
through cast-in-place concrete construction pipes. Additionally WATERSTOP-RX can seal Tightly butt coil ends together to form a con-
joints by expanding upon contact with water around concrete pilings and steel H-piles tinuous waterstop - do not overlap coil ends.
to form a positive seal against the concrete. passing through the slab. WATERSTOP-RX Place in maximum practical lengths to mini-
The key to WATERSTOP-RX’s effectiveness is works in both continuous hydrostatic and in- mize coil end joints. Where required, cut coils
its superior expansion to seal and ill voids termittent hydrostatic conditions. with a sharp knife or utility blade to it coil
and cracks in the concrete. WATERSTOP-RX ends together. Make horizontal to vertical
is an active bentonite/butyl-rubber based WATERSTOP-RX products are designed for transitions by abutting product coil sections
waterstop that is designed to replace pas- reinforced structural concrete with a mini- together, no special accessory pieces are re-
sive PVC/Rubber dumbbell waterstops, mum of 20N/mm2 (3,000 psi) compressive quired.
thereby eliminating the requirement of spe- strength. RX-101 and RX-101T are designed
cial pieces, split-forming and seam welding. for concrete 200 mm (8”) thick or greater At structural and pipe penetrations, cut into
WATERSTOP-RX has been successfully tested with two rows of reinforcing steel. RX-102 strips to it around the penetration. Apply to
by independent testing irms to over 60 me- is designed for vertical concrete 150 mm adhesive and abut coil ends together.
ters (200 feet) of hydrostatic water pressure, (6”) thick or greater; and horizontal concrete
under both continuous immersion and wet/ no less than 100 mm (4”) thick. RX-102 On irregular surfaces such as stone or rough
dry cycling. should be used in concrete with one row of concrete, make sure WATERSTOP-RX remains
steel reinforcement, concrete curbs, planter in direct contact with the substrate along the
WATERSTOP-RX is available in three sizes walls, fountains, and lightweight structural entire installation. There should not be any
and shapes (see Product Table). WA- concrete. air gap between the WATERSTOP-RX and the
TERSTOP-RX 101 is produced in a rect- WATERSTOP-RX is a reliable, cost-effective substrate.
angular shape measuring 25 x 20 mm means to stop water iniltration through con-
(1” x 3/4”). WATERSTOP-RX 101T is produced crete cold joints. It can also be used around Footing/Wall Joint
in a trapezoidal shape measuring 31 x 12 pipe and structural penetrations
mm (1-1/4” x 1/2”) with a reinforcing plastic
scrim embedded in the top surface for high WATERSTOP-RX
tensile strength. The patented trapezoidal
INSTALLATION
Surface preparation: Surfaces should be
shape distributes the expansive force over a
clean and dry. Remove all dirt, rocks, rust or
greater area and allows the concrete to low
other construction debris. Do not install WA-
more readily over the product during place-
TERSTOP-RX in standing water or on an iced
ment. WATERSTOP-RX 102 is produced in a
substrate.
half-circle (Crescent) shape measuring 19 x 9
mm (3/4” x 3/8”).
Adhesive: Apply a continuous bead of CET-
SEAL along the substrate where WATERSTOP-
Though WATERSTOP-RX possesses good
RX will be installed. Assure proper 75 mm (3”)
resistance to many chemicals, the waterstop
concrete coverage will be maintained. Keep
is not intended to be used as the primary
the nozzle tip pressed against the concrete
joint sealant for chemical containment ves-
at a 45o angle during application.
sels. Consult manufacturer for guidance re-
garding chemical compatibility for secondary
Installation: After applying a continuous bead
chemical containment applications. Addition- Place WATERSTOP-RX
of CETSEAL, remove release paper, then irm-
ally, WATERSTOP-RX is not an expansion joint inside of outer most
ly press the entire length of WATERSTOP-RX
sealant; contact CETCO for expansion joint reinforcing dowels
onto the adhesive. For vertical and overhead 75 mm
applications. (3”)
applications, irmly press a minimum of 15
Minimum 75 mm (3”)
seconds to assure adhesion. For best results
to exterior surface of
APPLICATIONS apply WATERSTOP-RX within 15 minutes of
wall
Applications include both vertical and hori- adhesive installation. WATERSTOP-RX must
zontal non-moving concrete construction be placed into adhesive prior to CETSEAL General Application Detail
WATERSTOP-RX®
EXPANDING CONCRETE JOINT WATERSTOP
Installation with REVO-FIX: REVO-FIX is a alone. Do not use any other adhesive or con- In conditions where severe ground water
steel mesh used to mechanically secure struction sealant, except CETSEAL, to secure chemical contamination exists, or is expected,
WATERSTOP-RX 101 into position using the WATERSTOP-RX. consult manufacturer for product chemical
accompanying supplied fasteners. Remove compatibility information.
release paper and place the WATERSTOP-RX WATERSTOP-RX is not designed, nor intended
on the concrete substrate. Then place REVO- to function as an expansion joint sealant. For
FIX strips over the WATERSTOP-RX, lapping precast concrete applications, contact manu-
PACKAGING
RX-101: 30 m (100 ft./box)
the strip ends by 25 mm (1”) maximum. Nail facturer for product suitability and for any spe-
RX-101T: 36 m (120 ft./box)
through LAP with fastener supplied, and install cial installation requirements.
RX-102: 60 m (200 ft./box)
one fastener 300 mm (12”) on center along
CETSEAL and REVO-FIX are packaged sepa-
the REVO-FIX. WATERSTOP-RX products are designed for
rately.
structural concrete with a minimum of 20N/
End-to-end or end-to-side REVO-FIX junctions mm2 3,000 psi compressive strength. WA-
are created by simple butt joints pressed irm- TERSTOP-RX 101 and RX-101T require a ACCESSORY PRODUCTS
ly together. Start at junctions; do not stretch minimum of 3” (75 mm) of concrete coverage. CETSEAL is a multi-purpose, single compo-
WATERSTOP-RX to it. Do not overlap water- WATERSTOP-RX 102 requires a minimum con- nent polyether moisture cure adhesive used
stop. crete coverage of 2” (50 mm). WATERSTOP-RX to secure WATERSTOP-RX into position. Apply
should only be used in applications where the a continuous bead of CETSEAL to substrate
product is completely encapsulated within the then install WATERSTOP-RX before CETSEAL
LIMITATIONS concrete. skins over and cures. Adhesive yield will vary
WATERSTOP-RX is not a self-adhering product.
with use, substrate and application.
CETSEAL or REVO-FIX is required to secure
WATERSTOP-RX should not be prehydrated by
WATERSTOP-RX to concrete, metal, or PVC
being subjected to submersion or remain in
(Pipe) surfaces. Mechanical fasteners should
extended contact with water prior to encap-
be used with REVO-FIX to secure WATERSTOP-
sulation in concrete. If the product exhibits
RX 101; and fasteners can be used in con-
considerable swell prior to encapsulation in
junction with CETSEAL. Mechanical fasteners
the concrete, it must be replaced with new
should not be used to secure WATERSTOP-RX
material.
FORM: TDS_Bentogrout_AM_201308_V1
WATERSTOP-RX®
EXPANDING CONCRETE JOINT WATERSTOP
STEP 5 WATERSTOP-RX
Concrete
POUR
CONCRETE
WATERSTOP-RX®
EXPANDING CONCRETE JOINT WATERSTOP
Install WATERSTOP-RX at
footing/wall joint
WATERSTOP-RX WATERSTOP-RX
(min 75 mm (3”) coverage) Non-shrink grout (min 75 mm (3”) coverage)
Concrete
Pipe Pipe sleeve Pipe
Concrete
Cast-in-Place Penetration Sleeved Penetration Detail
FORM: TDS_WATERSTOP-RX_AM_EN_201608_V3