Professional Documents
Culture Documents
EX260 SPR A - Engim
EX260 SPR A - Engim
EX260 SPR A - Engim
In order to configure the SI unit in the PROFIBUS DP network, you will require the
Select the appropriate cables to fit with the connectors mounted on the SI unit.
appropriate follwing Device master file (GSD) for the SI unit.
Operation Manual <EX260-SPR1/-SPR2/-SPR3/-SPR4>
7
Fieldbus interface connector layout
<EX260-SPR1/-SPR2/-SPR3/-SPR4>
Current GSD file can be found on the SMC website (URL http://www.smcworld.com).
GSD file
Part number GSD file
BUS OUT: M12 5-pole Socket B-coded
EX260 Series for PROFIBUS DP 1
No. Designation Description
1 EX260-SPR1/-SPR2 Smc_1430.gsd
1 4 5 2 1 - Unused
2 EX260-SPR3/-SPR4 Smc_1431.gsd
Thank you for purchasing an SMC EX260 Series Fieldbus device (Hereinafter 2 RXD/TXD-N Receive/transmit data, negative
3 EX260-SPR5/-SPR6 Smc_1432.gsd
referred to as "SI unit" ). 2 3 4 EX260-SPR7/-SPR8 Smc_1433.gsd
3 - Unused
Please read this manual carefully before operating the product and make sure you Output number assignment
4 RXD/TXD-P Receive/transmit data, positive
understand its capabilities and limitations. Output number starts at zero and refers to the solenoid position on the manifold.
5 - Unused
Please keep this manual handy for future reference.
6 Bit: 7 0 Byte
5 3
BUS IN: M12 5-pole Plug B-coded
0 Offset
0: Solenoid valve: OFF 16 outputs
To obtain more detailed information about operating this product, No. Designation Description
1: Solenoid valve: ON
Bit: 7 0 Byte type
please refer to the SMC website (URL http://www.smcworld.com) or 4 8 4 5 2 1 - Unused 1 Offset 32 outputs
Bit: 7 0 Byte type
contact SMC directly. <EX260-SPR5/-SPR6/-SPR7/-SPR8> 1
2 RXD/TXD-N Receive/transmit data, negative
2 Offset
3 - Unused
Bit: 7 0 Byte
4 RXD/TXD-P Receive/transmit data, positive
7 3 Offset
Safety Instructions 5 - Unused
Bit No. 0 2 4 6 0 0 4 6
These safety instructions are intended to prevent hazardous situations and/or <EX260-SPR5/-SPR6/-SPR7/-SPR8> Output No. 0 2 4 6 8 16 28 30 Solenoid on side A
equipment damage. 5 BUS: D-sub 9-pole Socket Side D
These instructions indicate the level of potential hazard with the labels of (SI unit side)
"Caution", " Warning" or "Danger". They are all important notes for safety and 3 No. Designation Description
Output No. 1 3 5 7 9 17 29 31 Solenoid on side B
must be followed in addition to International standards (ISO/IEC), Japan Industrial 1
1 - Unused Bit No. 1 3 5 7 1 1 5 7
6
Standards (JIS) and other safety regulations. Threaded screw 2 2 - Unused Valve manifold
7
hole size: #4-40 3
8 3 RXD/TXD-P Receive/transmit data, positive Diagnostic information
4
6 9 4 - Unused
CAUTION indicates a hazard with a low level of risk which, if 5 The EX260 SI unit can support total 8 bytes diagnostic information, six bytes standard
Caution: not avoided, could result in minor or moderate injury.
4
8 5 DGND Data ground (reference potential to VP)
diagnostic information and two bytes SI unit-related diagnostic information.
6 VP Power supply plus (P5V)
WARNING indicates a hazard with a medium level of risk Diagnostic information can be requested by the DP master from the SI unit, and such
Warning: which, if not avoided, could result in death or serious injury. No. Element Description
7
8 RXD/TXD-N
- Unused
Receive/transmit data, negative
system fault state can be displayed on the SF LED.
1 Fieldbus interface connector (BUS OUT) PROFIBUS DP connection (M12 5-pole socket, B-coded) The technical document states detail diagnostic information can be found on the SMC
DANGER indicates a hazard with a high level of risk which, if 9 - Unused
Danger: not avoided, will result in death or serious injury.
2
3
Fieldbus interface connector (BUS IN)
Fieldbus interface connector
PROFIBUS DP connection (M12 5-pole plug, B-coded)
PROFIBUS DP connection (D-sub 9-pole socket) Power supply connector layout
website (URL http://www.smcworld.com).
<EX260-SPR5/-SPR6/-SPR7/-SPR8>
URL http://www.smcworld.com
EX260-SPR5/-SPR6/-SPR7/-SPR8 do not have a built-in
Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN
termination resistor. Phone: +81 3-5207-8249 Fax: +81 3-5298-5362
Termination is required on the outside of the SI unit. You may use the termination Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.
switch built-in to PROFIBUS DP D-sub connector. © 2010 SMC Corporation All Rights Reserved