Professional Documents
Culture Documents
MSDS - Waterstop
MSDS - Waterstop
Note: The details and information stated within this MSDS have been provided by the manufacturer.
Manufacturer’s Reference Number: 13/06/2011
Refer to www.corkjoint.com to obtain the most recent MSDS.
PRODUCT IDENTIFICATION
COMPOSITION/INFORMATION ON INGREDIENTS
HAZARDOUS IDENTIFICATION
PHYISCAL/CHEMICAL CHARACTERISTIC
The information and the recommendations relating to the application and end use of this product are given in good faith and/or are based on the information provided by the
manufacturer of the product. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or fitness for a
particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written and/or oral recommendations, or
from any other advise offered by the Company, As such, no responsibility or liability by the Company will be accepted in respect of use of this product and the user shall determine the
suitability of the product for his intended use and assume all risks and liability in connection therewith. The information contained in our Material Safety Data Sheet may change at any
time without notice.
Page 2 of 4
Special Hazard
Combustible
Emission of irritating and corrosive hydrogen chloride gas during combustion.
PVC compound is self-extinguishing
The information and the recommendations relating to the application and end use of this product are given in good faith and/or are based on the information provided by the
manufacturer of the product. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or fitness for a
particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written and/or oral recommendations, or
from any other advise offered by the Company, As such, no responsibility or liability by the Company will be accepted in respect of use of this product and the user shall determine the
suitability of the product for his intended use and assume all risks and liability in connection therewith. The information contained in our Material Safety Data Sheet may change at any
time without notice.
Page 3 of 4
TOXICOLOGY INFORMATION
ECOLOGICAL INFORMATION
DISPOSAL CONSIDERATION
Disposal Method
Landfill & high temperature modern incineration under controlled conditions.
TRANSPORT INFORMATION
REGULATORY INFORMATION
Not regulated
The information and the recommendations relating to the application and end use of this product are given in good faith and/or are based on the information provided by the
manufacturer of the product. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or fitness for a
particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written and/or oral recommendations, or
from any other advise offered by the Company, As such, no responsibility or liability by the Company will be accepted in respect of use of this product and the user shall determine the
suitability of the product for his intended use and assume all risks and liability in connection therewith. The information contained in our Material Safety Data Sheet may change at any
time without notice.
Page 4 of 4
OTHER INFORMATION
The information contained herein is based on the present state of our knowledge and is intended to describe our
product from the point and health and safety requirements. It should therefore not to be constructed as guaranteeing
specific properties. Product should be stored, handled and used in compliance with applicable country, state, local laws
and regulations.
The information and the recommendations relating to the application and end use of this product are given in good faith and/or are based on the information provided by the
manufacturer of the product. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or fitness for a
particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written and/or oral recommendations, or
from any other advise offered by the Company, As such, no responsibility or liability by the Company will be accepted in respect of use of this product and the user shall determine the
suitability of the product for his intended use and assume all risks and liability in connection therewith. The information contained in our Material Safety Data Sheet may change at any
time without notice.
SURE-STOP® PVC WATERSTOP INSTALLATION GUIDELINES
1. Prior to placement, all Sure-Stop® PVC Waterstop joins and intersections must be welded together on site
using our recommended welding and joining procedure (refer to our “CORKJOINT Sure-Stop® PVC Waterstop
Site Joining Guidelines” brochure). In some instances, the waterstops may have to be welded together after
initial installation or after concrete placement has taken place because continuation of the Sure-Stop® PVC
Waterstop could not be performed prior, due to placement difficulties etc.
2. Sure-Stop® PVC Waterstop should be positioned inside the joint so that one half of the waterstop width is
embedded into each concrete pour. (Refer FIG. 1)
3. INTERNAL Sure-Stop® PVC Waterstops must be securely tied into position through the pre-punched eyelets
located on the external outer flanges of the waterstop. These are positioned every 150mm apart along both
outer edges of the waterstop, giving a very secure fixing position. In vertical joint applications, the placement of
form work is then positioned below and on top of the waterstop by butting up to it from both sides, achieving a
split formwork outcome, which also helps secure/hold the waterstop into position. (Refer FIG. 2) Usually in
horizontal joint applications no formwork is required.
4. EXTERNAL Sure-Stop® PVC Waterstop are secured into position by concrete nails that are hammered through
the specially designed outer flange areas of the waterstop, into the lean concrete base (blinding layer) for slab
on ground applications or by nails or screws into the formwork, for wall applications. In vertical joint applications
the placement of formwork is then positioned on top of the waterstop by butting up to it. This also helps
secure/hold the waterstop into position. (Refer FIG. 3)
5. To achieve the ultimate installation procedure, carefully place the concrete so as not to displace Sure-Stop® PVC
Waterstop from its position. Thoroughly vibrate concrete around the waterstop to avoid air entrapment and to
provide a positive contact between the waterstop and the concrete. Particular care should be taken when
installing internal waterstops for slab on ground applications to make sure concrete is fully vibrated and
compacted around and underneath the waterstop and all its ribs. (Refer FIG. 4)
6. Please also refer to our “CORKJOINT Sure-Stop® PVC Waterstop Site Joining Guidelines” for further information
on Sure-Stop® PVC Waterstop welding/joining procedures and preparation and installation procedures.
The information and the recommendations relating to the application and end use of this product are given in good faith and are based on the information provided by the manufacturer of
the product and/or the Company’s current knowledge and experience in connection with the product when properly stored, handled and applied under normal conditions and no liability of
final function at the job site is assumed. In practice, the differences in materials substrates and actual site conditions are such that no warranty in respect of merchantability of or fitness for
particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written and/or oral recommendations, or from
any other advise offered by the Company. The Company also has no express or implied knowledge of any particular purpose for which the product is required and any such information given
will not be taken into account in the supply of this product. No responsibility or liability by the Company will be accepted for misuse, misreading or derivation from recommended guidelines
in respect of this product and the user shall determine the suitability of the product for his intended use and assume all risks and liability in connection therewith. The information contained
in these documents may change at any time without notice. Any use of this product in any application should be approved as suitable for use/application by the Design Engineer and Project
Manager.