Professional Documents
Culture Documents
Loctite Seçim Tablosu
Loctite Seçim Tablosu
6
Bonding
Surface Preparation
Correct surface preparation is the most important factor to ensure the total success of any adhesive
performance.
šDegrease, clean and dry threads prior to applying the adhesive – use LOCTITE SF 7063 (see
Cleaning on page 110)
šIf the parts were in contact with aqueous washing solutions or cutting fluids which leave a
protective layer on the surface, wash with hot water
šIf the adhesive is applied below 5°C, pre-treatment with LOCTITE SF 7240 or LOCTITE SF 7649 is
advised (see Surface Preparation on page 133)
šFor locking of plastic fasteners: see Instant Adhesives on pages 30 – 37
Dispensing Equipment
Semi-Automatic Dispensing Equipment
LOCTITE 97009 / 97121 / 97201
LOCTITE Semi-Automatic Dispensing Equipment combines a controller and reservoir into a single
unit for valve dispensing of many LOCTITE Threadlockers it provides digital timing control and is
equipped with low level sensing. Pinch Valve is suitable for stationary or hand-held mode. The
reservoirs are large enough to accept up to 250ml bottles.
97001 / 98414
For information on semi or fully automatic dispensing equipment, available valves, spare parts, accessories and dispensing tips, please
refer to pages 152 – 163 or the LOCTITE Equipment Sourcebook.
Very difficult to disassemble with standard Very difficult to disassemble with standard Medium and high strength semi-solid
hand tools; may require localised heat for hand tools; may require localised heat Threadlocker Sticks that can be used on
removal. Good for permanent assemblies on for removal. For preassembled fasteners, thread size up to M50. Removable with
heavy equipment, studs, motor and pump instrumentation or carburettor screws. standard hand tools.
mounts, for thread size up M80.
7
Threadlocking Adhesives
Product Table
Yes
Wicking grade
Liquid Liquid
LOCTITE LOCTITE
Solution
290 222
No
Medium High
2 hr 2 hr 3 hr 3 hr
26 Nm 20 Nm 33 Nm 20 Nm
10ml, 50ml, 250ml, 2 ltr 5ml, 50ml, 250ml 10ml, 50ml, 250ml 5ml, 50ml, 250ml
9
Threadlocking Adhesives
Product List
Max. Service
Chemical Breakaway
Product Colour Fluorescence thread temperature Strength Thixotropy
basis torque
size range
LOCTITE 241 Blue opaque Yes M12 -55°C to +150°C Medium 11.5 Nm No
LOCTITE 242 Blue Yes M36 -55°C to +150°C Medium 11.5 Nm Yes
10
Bonding
Fixture time
Fixture time Fixture time
Viscosity stainless Pack sizes Comments
steel brass
steel
100 – 150 mPa·s 25 min. 20 min. 210 min. 250ml Low strength, low viscosity, small threads
10ml, 50ml,
900 – 1,500 mPa·s 15 min. 8 min. 360 min. Low strength, general purpose
250ml
100 – 150 mPa·s 35 min. 12 min. 240 min. 250ml Medium strength, low viscosity, small threads
800 – 1,600 mPa·s 5 min. 15 min. 20 min. 250ml Medium strength, medium viscosity, general purpose
10ml, 50ml,
1,300 – 3,000 mPa·s 10 min. 5 min. 10 min. Medium strength, general purpose
250ml, 2 ltr
5,600 – 10,000 mPa·s 20 min. 12 min. 240 min. 50ml, 250ml Medium strength, medium viscosity, large threads
1,200 – 2,400 mPa·s 15 min. 8 min. 180 min. 250ml Medium/high strength, general purpose
Semi-solid 5 min. – 5 min. 9g, 19g High strength, positioning; maintenance, repair and overhaul
10ml, 50ml,
400 – 600 mPa·s 10 min. 10 min. 150 min. High strength, general purpose
250ml
Not available in
400 – 600 mPa·s 10 min. 5 min. 15 min. High strength, low viscosity
the U.K.
4,000 – 15,000 mPa·s 40 min. – – 50ml, 250ml High strength, high temperature resistant
50ml, 250ml,
5,000 – 10,000 mPa·s 15 min. 7 min. 180 min. High viscosity, high strength, large threads
2 ltr
380 – 620 mPa·s 3 min. 3 min. 5 min. 50ml High strength, especially for nickel surfaces
6,000 – 8,000 mPa·s 30 min. 25 min. 270 min. 50ml High viscosity, high strength, large threads
2,400 – 3,600 mPa·s 20 min. 20 min. 60 min. 50ml, 250ml High strength, high temperature resistant
10ml, 50ml,
20 – 55 mPa·s 20 min. 20 min. 60 min. Medium/high strength, wicking grade
250ml, 2 ltr
5ml, 50ml,
225 – 475 mPa·s 10 min. 8 min. 10 min. Medium strength, no labelling, white MSDS
250ml
5ml, 50ml,
350 – 550 mPa·s 5 min. 4 min. 5 min. High strength, no labelling, white MSDS
250ml
10ml, 50ml,
500 – 900 mPa·s 10 min. 4 min. 25 min. High strength, especially for chromated surfaces
250ml, 1 ltr, 2 ltr
11