Professional Documents
Culture Documents
Display Description
Display Description
1CS120852
Rev. ind.
A
Techn. Area / DCC Page
Display Description
E /& FC101 1 (69)
Display Description
PWCP
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Contents
PWCP
1 General ...........................................................................................................4
1.1 Purpose of this document
1.2 The SGT-700 displays
1.3 Compressor and Gas Process displays
4.1 General
4.2 Fuel System Display abbreviations
1 General
2.1 General
The Unit Operation display is used during the start-up sequence, normal operation and the
shut down sequence. It includes functions to select turbine controller, fuel-mode and to
start and stop. The display also indicates whether a certain Function Group (FG) is in
operation or not. This is shown in the Start Indication column. The most important values
such as temperature, pressure and process data can also be observed here.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
MIMIC DISPLAY
T0/H0 Ambient air temperature/humidity
T2/P2 Compressor inlet temperature/pressure
T3/P3 Compressor discharge temperature/pressure
T7/P8 Exhaust gas temperature/pressure
GG Speed Gas Generator Speed
PT Speed Power Turbine Speed
Suction Suction Side of Compressor
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
OPERATIONAL MODE
Internal Operation from gas turbine control system
External Operation from customer DCS
Off No operation possible
GOVERNING MODE
Speed mode Activate Speed Mode
SP Internal Speed Setpoint
Load Sharing Mode Load Sharing Mode Activated
COMPRESSOR PHASE
Phase 1 Control System Logic for Design Phase 1 Activated
Phase 2 Control System Logic for Design Phase 2 Activated
Phase 3 Control System Logic for Design Phase 3 Activated
Phase 4 Control System Logic for Design Phase 4 Activated
UNIT OPERATION
Ready to Start All start orders are ignored (Start interlock) until the unit is ready for
start.
Preparation Preparation of compressor before start
Start/Stop Function group (FG) for start and stop of GT
START INDICATION
Ventilation Indicates when the ventilation is put into service and purging of all
rooms of the unit is proceeding.
Lub. Oil The lubricating oil system is activated.
Purge/Fuel Pr. The barring starts and purging of the turbine is proceeding and the fuel
system is started.
Pilot Ignition Ignition of pilot flame
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Acc With Starter Acceleration of the gas turbine by both start motor and combustion of
fuel.
Acceleration Start motor is stopped and acceleration is carried out by combustion of
fuel.
Turbine In Service Turbine and Gas Compressor in service and unit on Load
Purge Time Indicates the remaining time for the purge sequence.
STOP INDICATION
Start Abort Indicates that the abortion of the start sequence is activated.
UL90 Shutdown An unloading shutdown is initiated. The unit will be unloaded until the
fault disappears or the active load is zero. Maximum 90 second.
UL30 Shutdown An unloading shutdown is initiated. The unit will be unloaded until the
fault disappears or the active load is zero. Maximum 30 second.
Instant Shutdown Indicates that an instant shutdown trip is activated.
Stopping Indicates that the stop sequence is activated.
Warm Turbine Indicates that the cooling down sequence will be activated after a stop
or trip.
Barring
Indicates turning of turbine-shaft.
Cool Down Time
Indicates the remaining time for the cooling down sequence.
SEQUENCES
Turb Sequence Turbine sequence
Unit Sequence Main sequence start/stop of unit
Fuel Sequence Gas fuel sequence
Comp Prep Sequence Compressor Preparation Sequence
Comp Sequence Compressor Sequence
T7L Limits the average turbine exhaust temperature. The set point is
calculated according to the ambient air conditions.
NGG Limits the speed of the gas generator rotor. The set point is calculated
according to the ambient air conditions. The limiter uses two setting
levels, one for start and one for service
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
The limiters are presented with one bar graph for the measured value and one for the limiting set point.
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
The limit set point bar graph starts at the top of the diagram and expand downwards by decreasing value.
3.1 General
The Log Page displays are used when all possible values needed are presented on one
page. This page is also used when performing a Routine Reading printout. In the figure
below you can overview all the values presented in log page.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
TURBINE DATA
NGG Rotation speed of the gas generator shaft
NGG* Normalized rotation speed (according to ambient temperature) of the
gas generator shaft
NPT Rotation speed of the power turbine shaft
IGV Inlet guide vane position
Barring Gas Compressor is Barring
Cooling Time Indicates the elapsed time for the cooling down sequence
We reserve all rights in this document and in the information
HISTORICAL DATA
Starts Total numbers of starts
Operating Hours Total GT operating hours
Equivalent Hours Total GT equivalent operating hours
Primary Vent Pressure NDE Primary Vent Pressure Not Driven End 1´ST Compressor
(PIT-2303)
Primary Seal Vent Pressure Primary Seal Vent Pressure 1´ST Compressor
(PIT-2311)
Separation Gas Supply Separartion Gas Supply Pressure 1´ST Compressor
Pressure (PIT-2007)
Primary Vent Pressure NDE Primary Vent Pressure Not Driven End 2&3´ST Compres
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
(PIT-2514)
Primary Seal Vent Pressure Primary Seal Vent Pressure 2&3´ST Compressor
(PIT-2516)
Separation Gas Supply Separartion Gas Supply Pressure 2&3´ST Compressor
Pressure (PIT-2511)
COMPR BEARINGS
PHASE 1, 2 & 3, 4
Compr Vibration DE X 1´ST Compressor vibration Driven End measure point X
(VE1447X)
Compre Vibration DE Y 1´ST Compressor vibration Driven End measure point Y
(VE1447Y)
Compr Vibration NDE X 1´ST Compressor vibration Non Driven End measure point X
(VE1446X)
Compr Vibration NDE Y 1´ST Compressor vibration Non Driven End measure point Y
(VE1446Y)
Axial Displ. Compr 1´ST Compressor Axial Displacement
(VE1445A)
Axial Displ. Compr 1´ST Compressor Axial Displacement
(VE1445B)
Radial Bearing DE Temp 1´ST Compressor Radial Bearing Temperature Driven End
(TE-1441)
Radial Bearing DE Temp 1´ST Compressor Radial Bearing Temperature Driven End
(TE-1442)
Axial Bearing Outb Temp 1´ST Compressor Axial Outboard Bearing Temperature
(TE-1431)
Axial Bearing Outb Temp 1´ST Compressor Axial Outboard Bearing Temperature
(TE-1432)
Axial Bearing Inb Temp 1´ST Compressor Axial Inboard Bearing Temperature
(TE-1435)
Axial Bearing Inb Temp 1´ST Compressor Axial Inboard Bearing Temperature
(TE-1436)
Radial Bearing NDE Temp 1´ST Compressor Radial Bearing Temperature Not Driven End
(TE-1439)
Radial Bearing NDE Temp 1´ST Compressor Radial Bearing Temperature Not Driven End
(TE-1440)
COMPR BEARINGS
PHASE 3 & 4
Compr Vibration DE X 2&3´ST Compressor vibration Driven End measure point X
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
(VE1417X)
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
BEARINGS
1 GG Radial Temperature and vibration of bearing 1, gas generator
1 GG Axial Temperature of axial bearing, gas generator
2 GG Radial Temperature and vibration of bearing 2, gas generator
3 PT Radial Temperature and vibration of bearing 3, power turbine
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
AIR INTAKE
Ambient Temp T0 Ambient air temperature
Humidity H0 Ambient air humidity
DP Air Intake Filter Differential pressure over air intake filter
DP Pre-Filter Differential pressure over Pre-filter
DP High Efficiency Filter Differential pressure over high efficiency filter
Sealing Air Temp Temperature sealing air
LUBRICATION OIL
Bearing 2 DP Differential pressure between lubrication oil pressure and bearing
house pressure in bearing no. 2
Supply Press Oil-supply pressure to all bearings except bearing no 2
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
EXHAUST TEMP T7
XE01 CT005 to CT080 Shows the first ring of measuring points
XE02 CT005 to CT080 Shows the second ring of measuring points
T7 Avg Average exhaust temperature per ring
T7 Avg Total average exhaust temperature
T7 Min To Avg Shows the minimum temperature below average
T7 Max To Avg Shows the maximum temperature above average
T7 Max Start Max average temperature during latest start
COMBUSTOR
PULSATIONS
Low Frequency Low Frequency
High Frequency High Frequency
Narrow Frequency Narrow Frequency
4.1 General
The Fuel System display includes the Gas Fuel System and the Ignition system. For more
information about the systems, see the Process & Instrumentation Diagrams, System
Descriptions and Component Lists.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
FUEL SYSTEM
Pilot Ignition FG Pilot ignition function group
FG Gas Fuel Gas fuel function group
Gas Fuel Seq Gas fuel sequence
ENERGY FLOW
Gas Gas fuel heat flow
Total Total fuel heat flow
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
GT MAIN DATA
NGG Rotation speed of the Gas Generator shaft
NPT Rotation speed of the Power Turbine shaft
T0 Ambient air temperature
T7 Total exhaust average temperature
P3 Compressor discharge pressure
5.1 General
The Lubrication Oil display includes two systems: the Lube Oil System and the Start
System. The figure below shows the lube oil tank, the lube oil pumps, filters, pipes and
bearings. For more information about the systems, see the Process & Instrumentation
Diagrams, System Descriptions and Component Lists.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Indicates that the cooling down sequence will be activated after a stop
contained therein. Reproduction, use or disclosure to third
Warm Turbine
or trip
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
GT MAIN DATA
NGG Rotation speed of the Gas Generator shaft
NPT Rotation speed of the Power Turbine shaft
T0 Ambient air temperature
T7 Total exhaust average temperature
P3 Compressor discharge pressure
6.1 General
The Air Intake display includes the Air Intake and Cooling Air, Instrument Air and Gas
turbine system.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
GT MAIN DATA
© Siemens Industrial Turbomachinery AB
7 Bearings Display
7.1 General
The Bearings display contains temperature/vibration information about the axial bearings
as well as the radial bearings on the GT.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
GT MAIN DATA
NGG Rotation speed of the Gas Generator shaft
NPT Rotation speed of the Power Turbine shaft
T0 Ambient air temperature
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
8 Ventilation Display
8.1 General
The Ventilation display shows the position of fire shut off dampers and operation modes
of the fans for the ventilation system.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
FIRE SYSTEM
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
GT MAIN DATA
NGG Rotation speed of the Gas Generator shaft
NPT Rotation speed of the Power Turbine shaft
T0 Ambient air temperature
T7 Total exhaust average temperature
P3 Compressor discharge pressure
9.1 General
This display shows the emission process. Compressed air is mixed with gas fuel and burnt
in the combustion chamber producing hot gas at high velocity as input to the gas turbine.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
EMISSION CONTROL
Disable Bypass Control Disables control of bypass valves
Disable BV2 Emis. Ctrl Disables emission control for bleed valve 2
SP Bypass Area Calculated set point bypass area
MV Bypass Area Calculated measured value bypass area
Calc. Flame Temp Calculated flame temperature
GT MAIN DATA
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
10.1 General
The Turbine Governing display shows the turbine governor in operation.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
TURBINE GOVERNING
FSC SP Set point for flame sustain control
STC SP G Set point to the start controller
STC O SP Offset to the start controller, manually set by the operator
MPC MV Measured value of the max position controller. Fuel control tests, gas
fuel.
MPC O SP Set point of the max position controller. Fuel control tests, gas fuel.
GAC SP Set point of the gas generator acceleration controller (limiter)
We reserve all rights in this document and in the information
GAS
Pilot Test SP Set point for pilot gas fuel valve for test purpose, only possible to set
during standstill
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Main Test SP Set point for main gas fuel valve for test purpose, only possible to set
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
during standstill
Central Test SP Set point when testing Central Fuel Valve
GT MAIN DATA
NGG Rotation speed of the Gas Generator shaft
NPT Rotation speed of the Power Turbine shaft
T0 Ambient air temperature
T7 Total exhaust average temperature
P3 Compressor discharge pressure
11.1 General
The E&C display picture shows the ventilation fans, shut off dampers and differential
pressure for the control and battery room.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
FIRE SYSTEM
Warning Common fire pre alarm for the control module
Trip Fire detected in the control module
Equipment Fault Fire system fault
CO2 Released Fire system has released it’s CO2
Dampers Closed Dampers closed due to fire detected
GT MAIN DATA
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
12.1 General
The Start Block and Trips display shows possible active start blocking alarms and possible
active shutdowns. The different kinds of start blocks are; Start blocking alarms, Start
abort, Instant shutdown, Blow down, Unloading 90, Unloading 30 and Hard Wired
Click on the different blocks for detailed signal information.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
MIMIC DISPLAY
Startblock AL Start blocking alarms
Start Abort Shutdown during start-up and stand still. (Blocked during operation)
InstantSD Instant shutdown. Instant closing of fuel valves and closing of Suction
and Discharge valves.
Unload90 Shutdown with unloading during 90s (ramp rate is from full load to
zero in 90s) before Instant shutdown is activated. If the trip condition
disappears during the unloading, the shutdown is aborted and the GT
stays at current speed.
We reserve all rights in this document and in the information
Unload30 Shutdown with unloading during 30s (ramp rate is from full load to
contained therein. Reproduction, use or disclosure to third
Display Description
A
Doc. No.
Rev. ind.
E /& FC101
1CS120852
PWCP / BD000034
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Display Description
A
Doc. No.
Rev. ind.
E /& FC101
1CS120852
PWCP / BD000034
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Display Description
A
Doc. No.
Rev. ind.
E /& FC101
1CS120852
PWCP / BD000034
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Display Description
A
Doc. No.
Rev. ind.
E /& FC101
1CS120852
PWCP / BD000034
Operator Instruction Doc. No.
1CS120852
Rev. ind.
A
Techn. Area / DCC Page
Display Description
E /& FC101 38 (69)
13.1 General
This view is showing the total gas-process design around the compressor. During the life
time of this compressor station, the suction pressure will drop. To always stay at the same
discharge pressure in the future, the setup of the compressors and the gas process needs to
be changed depending on the pressure drop at the suction side. This is the reason to why
the project is divided in four different phases. There are 3 different displays the first one is
showing phase1 and 2 the other two are showing phase 3 and 4.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Display Description
A
Doc. No.
Rev. ind.
E /& FC101
1CS120852
PWCP / BD000034
Operator Instruction Doc. No.
1CS120852
Rev. ind.
A
Techn. Area / DCC Page
Display Description
E /& FC101 40 (69)
14.1 General
The displays are showing the controllers and limiters for the compressor. For more
information about the compressor controlling and limitations see doc 1CS110859. There
are different HMI-displays depending on the actual activated phase for the project.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Display Description
A
Doc. No.
Rev. ind.
E /& FC101
1CS120852
PWCP / BD000034
Operator Instruction Doc. No.
1CS120852
Rev. ind.
A
Techn. Area / DCC Page
Display Description
E /& FC101 42 (69)
SPEED CTRL
Speed SP Speed Set Point
Pigging CTRL Pigging controlling
LIMITERS
Compr Train Std Suction Compressor standard Flow Suction Flow Limiter
Flow Limiter
Compr Train Std Suction Compressor standard Flow Suction Flow Limiter Set Point
Flow Limiter SP
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Compr Train Std Suction Compressor standard Flow Suction Flow Limiter Measured Value
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Flow Limiter MV
Compr Train Suction Compressor Train Suction Pressure Limiter
Pressure Limiter
Compr Train Suction Compressor Train Suction Pressure Limiter Set Point
Pressure Limiter SP
Compr Train Suction Compressor Train Suction Pressure Limiter Measured Value
Pressure Limiter MV
Compr Train Discharge Compressor Train Discharge Pressure Limiter
Pressure Limiter
Compr Train Discharge Compressor Train Discharge Pressure Limiter Set Point
Pressure Limiter SP
Compr Train Discharge Compressor Train Discharge Pressure Limiter Measured Value
Pressure Limiter MV
LOAD SHARING
CONTROLLER
Station Flow Controller Station Flow Controller
Station Flow Controller SP Station Flow Controller Set Point
Station Flow Controller MV Station Flow Controller Measured Value
Station Discharge Pressure Station Discharge Pressure Controller
Controller
Station Discharge Pressure Station Discharge Pressure Controller Set Point
Controller SP
Station Discharge Pressure Station Discharge Pressure Controller Measured Value
Controller MV
OPERATIONAL MODE
Internal Operation from gas turbine control system
External Operation from customer drive control system DCS
Backup Operation from backup panel
Off No operation possible
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
GOVERNING MODE
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
SEQUENCES
Comp Sequence Compressor Sequence
Comp Prep Sequence Compressor Preparation Sequence
GT MAIN DATA
NGG Rotation speed of gas generator shaft.
NPT Rotation speed of power turbine shaft.
T0 Ambient temperature.
T7 Exhaust temperature.
P3 Compressor discharge pressure.
15.1 General
This display shows temperature/vibration information for bearings on the compressor.
There are different HMI-displays depending on the actual activated phase for the project.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Display Description
A
Doc. No.
Rev. ind.
E /& FC101
1CS120852
PWCP / BD000034
Operator Instruction Doc. No.
1CS120852
Rev. ind.
A
Techn. Area / DCC Page
Display Description
E /& FC101 46 (69)
GT MAIN DATA
NGG Rotation speed of the Gas Generator shaft
NPT Rotation speed of the Power Turbine shaft
T0 Ambient air temperature
T7 Total exhaust average temperature
P3 Compressor discharge pressure
16.1 General
The Sealing Gas Compressor display shows the compressor sealing, separation gas system
and the seal gas system. There is one seal gas system for stage 1 on the compressor and
one seal gas system for stage 2 and 3. There are different HMI-displays depending on the
actual activated phase for the project.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Display Description
A
Doc. No.
Rev. ind.
E /& FC101
1CS120852
PWCP / BD000034
Operator Instruction Doc. No.
1CS120852
Rev. ind.
A
Techn. Area / DCC Page
Display Description
E /& FC101 49 (69)
Confirm Ext Seal Gas Valve Confirm External Seal Gas Valve is Opened
Open
Separation Gas FG Separation Gas Function Group
Seal Gas FG Seal Gas Function Group
Comp Pressurized and Ready Compressor Pressurized and Ready to be started
to Start
Confirm Manually Drain Confirm Manually Drain of Compressor
Compressor Preparation Compressor Preparation Sequence
Sequence
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
GT MAIN DATA
© Siemens Industrial Turbomachinery AB
17.1 General
This display shows the anti surge control system. Depending on the actual phase, the
compressor and gas-process will change; this affects the anti surge amount of anti surge
controllers. There are different HMI-displays depending on the actual activated phase for
the project.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Display Description
A
Doc. No.
Rev. ind.
E /& FC101
1CS120852
PWCP / BD000034
Operator Instruction Doc. No.
1CS120852
Rev. ind.
A
Techn. Area / DCC Page
Display Description
E /& FC101 52 (69)
CONTROLLERS
Open Speed SP Open speed set point
Close Speed SP Close speed set point
Man SP Set point for manual operation of anti surge valve
ASC Anti Surge Controller
Ramp Surge controller ramping
Forced Open Surge control valve forced to open position
MAX Maximum selector
We reserve all rights in this document and in the information
GT MAIN DATA
NGG Rotation speed of the Gas Generator
NPT Rotation speed of the Power Turbine
T0 Ambient air temperature
T7 Total exhaust average temperature
P3 Compressor discharge pressure
18.1 General
At this view it is possible to supervise where at the surge map the compressor is operating
and how far from surge the actual operation point is. There are different Surge Maps for
the different compressor stages and depending on the actual operating phase.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Display Description
A
Doc. No.
Rev. ind.
E /& FC101
1CS120852
PWCP / BD000034
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Display Description
A
Doc. No.
Rev. ind.
E /& FC101
1CS120852
PWCP / BD000034
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Display Description
A
Doc. No.
Rev. ind.
E /& FC101
1CS120852
PWCP / BD000034
Operator Instruction Doc. No.
1CS120852
Rev. ind.
A
Techn. Area / DCC Page
Display Description
E /& FC101 58 (69)
ASCV Reset Forced Opened Anti Surge Controlling Valve Reset Forced Open
© Siemens Industrial Turbomachinery AB
GT MAIN DATA
NGG Rotation speed of the Gas Generator
NPT Rotation speed of the Power Turbine
T0 Ambient air temperature
T7 Total exhaust average temperature
P3 Compressor discharge pressure
19.1 General
This view is showing the total gas-process design around the compressor. During the life
time of this compressor station, the suction pressure will drop. To always stay at the same
discharge pressure in the future, the setup of the compressors and the gas process needs to
be changed depending on the pressure drop at the suction side. This is the reason to why
the project is divided in four different phases. There are 3 different displays the first one is
showing phase1 and 2 the other two are showing phase 3 and 4.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Display Description
A
Doc. No.
Rev. ind.
E /& FC101
1CS120852
PWCP / BD000034
Operator Instruction Doc. No.
1CS120852
Rev. ind.
A
Techn. Area / DCC Page
Display Description
E /& FC101 61 (69)
GT MAIN DATA
NGG Rotation speed of the Gas Generator
NPT Rotation speed of the Power Turbine
T0 Ambient air temperature
T7 Total exhaust average temperature
P3 Compressor discharge pressure
20.1 General
Depending on the phase of the project the 12 gas cooler fans will be used in different
blocks. These blocks are showed at these HMI-displays.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Display Description
A
Doc. No.
Rev. ind.
E /& FC101
1CS120852
PWCP / BD000034
Operator Instruction Doc. No.
1CS120852
Rev. ind.
A
Techn. Area / DCC Page
Display Description
E /& FC101 64 (69)
GT MAIN DATA
NGG Rotation speed of the Gas Generator
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
21.1 General
These displays are showing basic views for the total gas-process around the both
compressor trains. Both compressor trains are seen at the same display to easy supervise
the load sharing control. There are different displays depending on the actual phase of the
project.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Display Description
A
Doc. No.
Rev. ind.
E /& FC101
1CS120852
PWCP / BD000034
Operator Instruction Doc. No.
1CS120852
Rev. ind.
A
Techn. Area / DCC Page
Display Description
E /& FC101 67 (69)
22.1 General
The Log Page for the Gas Process is showing almost all values for the gas process. There
are different log pages depending on the actual phase of the project.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB
Display Description
A
Doc. No.
Rev. ind.
E /& FC101
1CS120852
PWCP / BD000034
Operator Instruction Doc. No.
1CS120852
Rev. ind.
A
Techn. Area / DCC Page
Display Description
E /& FC101 69 (69)
REVISION
Rev. Page (P) Description Date
ind. Chapt. (C) Dept. / Init.
We reserve all rights in this document and in the information
contained therein. Reproduction, use or disclosure to third
Parties without express authority is strictly forbidden.
© Siemens Industrial Turbomachinery AB