Professional Documents
Culture Documents
KL Tool Catalog Marine
KL Tool Catalog Marine
KL Tool Catalog Marine
K&L is committed to bringing you the best service possible. The K&L O.E. Division is
staffed with personnel dedicated to serving Original Equipment customers. If you have any
questions, concerns or suggestions, please contact a customer service representative at
800-708-3184 or fax 408-727-4305. We will assist you in any way we can.
All rights reserved. Any reprinting or unauthorized use without the written permission of
Yamaha Motor Corporation, U.S.A. is expressly prohibited. Specifications, features, and
options are subject to change without notice.
800.727.6767
1 1-800-708-3184 | kLsupply.com
Table of Contents
Table of Contents
3 Cylinder 2-Stroke. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
3 Cylinder 4-Stroke. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
8 Cylinder 4-Stroke. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
800.727.6767
3 INDEX 1-800-708-3184 | kLsupply.com
K&L SUPPLY CO.
Gear Shim Tool................................... 55 Oil Seal Installer................................. 27, 28, Ring Nut Wrench............................. 63, 79
Gland Nut Wrench...................................... 33, 37, 44, 51, 54, 62, 72, 79, 81 Roller Bearing Installer/Remover.............
.... 38, 39, 51, 53, 54, 55, 67, 71, 72 Oil Seal Puller...................................... 16 45, 55, 63
Outboard Marine Engine Stand........... 9
H Outer Race Installer...................... 28, 37 S
Heavy Duty Bearing Puller................ 79 P Sand Blast Cabinet & Parts.................... 22
High Current Shunt............................ 12 Shaft and Bearing Remover.................... 80
Hose Reel.............................................. 18 Peak Voltage Adapter...........................12 Shift Rod Push Arm..............45, 52, 71, 78
Hydraulic Drive Shaft......................... 65 Peak Voltage Test................................. 37 Shift Rod Socket........................... 63, 78
Hydraulic Press.................................... 16 Peak Volt Meter Adaptor.....................75 Socket Kit..............................................18
Hydraulic Pressure Gauge.................. 73 Pinion Bearing Shim Selector.............32 Socket Pinion Nut...............................80
Hydraulic PTT Pressure Gauge......... 82 Pinion Gear Spacer Installer................................... 52
Bushing Installer...................... 12, 27, 65 Spark Checker
I Pinion Gear Shim Gauge.................... 54 Oppama Pet-4000................................75
Indicator Rod........................................10 Pinion Gear Shim Tool........................55 Spark Plug Hole Stand........................14
Injector Driver Test Lead....... 43, 50, 60 Pinion Height Gauge.... 28, 38, 46, 70, 71 Spill Pan................................................24
Pinion Nut Holder................... 45, 64, 80 Stopper Guide Plate...................... 63, 81
K Pinion Nut Wrench................. 28, 38, 53 Stopper Guide Stand...........................69
Pinion Shim Gauge........................66, 81 Stopper Ring....................................... 53
K&L Deluxe Apron............................. 24 Pinion Shim Rod..................................66
Pinion Shim Selecting Tool.................12 T
L Pistion Ring Slider.............................. 62 Tachometer Digital............................. 75
Lighting Coil Test...... 49, 50, 60, 61, 75 Piston Ring Compressor......... 13, 31, 77 Taper Roller Bearing Installer........... 54
Piston Ring Installer.............................49 Terminal Crimper Tool...................... 11
M Power Extractor Set .............................15 Terminal Kits........................................11
Power Tilt Cylinder Cap Wrench.......40 Terminal Pin Cover.............................11
Magnetic Base.......................................18 Pressure Sensor Tester........................ 60
Magnetic Base Stand............................82 Terminal Removal Tool......................18
Primary Sheave Holder..................50, 77 Test Harness.................... 43, 59, 62, 75
Magnetic Flex Stand.............................14 Propeller Remover................................71
Marine Engine Stand ........................... 9 Test Tachometer...................................16
Propeller Shaft and Bearing Housing T-Handle Socket Kit............................18
Marine Fuel Pressure Gauge Kit. 44, 61, 76 Remover................................................ 51
MC800 Fuel Pump & Tools................ 11 T-Handle Spark....................................24
Propeller Shaft Oil Seal Installer..... 67, 68 Throttle Position Sensor Test ..... 49, 60
Measuring Cup.................................... 24 Propshaft End Seal Driver...................53
Metric Thread...................................... 15 Throttle Position Sensor Test Lead.....59
Propshaft Needle Tilt And Trim Wrench-V8................ 82
Multi Deburring Tool......................... 24 Bearing Attachment............................67, 68 Tilt Rod Wrench.................................55, 72
N Propshaft Seal Installer....................... 53 Tilt Wrench......................................... 56
PTT Cylinder Wrench........................ 56 Timing Belt Driven Gear Socket...... 59
Needle Bearing Attachment....................... PTT Piston Vise Tool.......................... 72 TNT Wrench................................. 55, 72
........ 62, 63, 64, 65, 66, 69, 70, 80 PTT Pressure Adapter Gauge............ 72 Torx Key Set........................................ 18
Needle Bearing Guide Plate................51 PTT Pressure Gauge.......... 55, 56, 72, 73 Transom Drill Fixture.........................10
Needle Bearing Installer.................... 27, 38, PTT Pressure Gauge Adapter. Pullers....... Trim Cylinder Wrench.... 34, 46, 72, 73
39, 51, 52, 53, 54, 69, 71, 79, 81 ......................... 16, 33, 40, 52, 64
Needle Bearing Remover/Installer............ Pulsar Coil Test Harness............................. U
27, 32, 37, 63 .............. 31, 43, 49, 50, 60, 75, 78
Neway Cutting Fluid............................17 Pulsar Coil Test Lead.......................... 60 Ultrasonic Cleaners.............................23
Neway Easy-Turn Wrench..................17 Ultrasonic Cleaner Soap.....................23
Neway PU1800 Power Unit.................17 R Ultrasonic Parts Washer.....................23
Neway Spray Bottle..............................17 Universal Magneto & Rotor Holder...13
Ratio-Rite Measuring Cup..................24 Universal Puller............................ 13, 82
Neway Valve Seat Kit............ 10, 61, 77 Rear Propeller Shaft Installer .............71 Up Relief Fitting......................... 70, 73
O Rectifer/Regulator Test....................... 76 Up Relief Fitting T&T Pres Test .......82
Rectifier/Regulator Test..... 43, 50, 59, 60
O2 Sensor Wrench.............................. 50 Reverse/Forward Gear Bearing Installer.. V
Oil Drain Installer/Remover .............. 33, 39, 45, 46, 54, 66, 71
Screw Tool....... 28, 34, 39, 45, 51, 71, 78 Reverse Gear Bearing Retainer/Installer.. V4/V6 Marine Engine Stand............ 57
Oil Filler Cap Installer/Remover Tool...... .................................................. 71 Vaccumate.......................................... 14
................................. 31, 44, 59, 78 Reverse Gear Shim Gauge...... 32, 38, 67 Vaccumate Carb................................. 14
Oil Filter Catch Pan............................. 78 Reverse Gear Shim Gauge Set.............39 Vaccum Tester/ Lower Unit
Oil Filter Wrench........................... 62, 77 Reverse Gear Shim Tool......................66 Pressure.......................................... 13, 78
Ring Nut Extension..............................81 Valve Adjuster......................................31
Valve Attachment................................... 43
Valve Guide Flex-Hones........................ 17
Valve Reamer Guide (5.5MM,5.53MM)...
INDEX: YB-06201....................................... 52, 69
800.727.6767
5 INDEX 1-800-708-3184 | kLsupply.com
K&L SUPPLY CO.
YE-A8535............................................ 18 YU-A1072........................................... 18
YE-A9042............................................ 24 YU-A1073........................................... 18
YM-01122...................................... 31, 59 YU-A1074........................................... 18
YM-01196......................... 31, 44, 59, 77 YU-A1087........................................... 18
YM-01253............................................ 10 YU-A1093........................................... 18
YM-04015...................................... 31, 43 YU-A1104........................................... 18
YM-04019...................................... 43, 77 YU-A1927........................................... 75
YM-04064-A....................................... 60 YU-A3353........................................... 15
YM-04066...................................... 43, 59 YU-A4061........................................... 24
YM-08035-A....................................... 31 YU-A4062........................................... 24
YM-08037...................................... 13, 77 YU-A5399........................................... 16
YM-34487............................................ 75 YU-A5400........................................... 14
YM-A0309........................................... 17 YU-A6375........................................... 24
YM-A8998..................................... 17, 78 YU-A6410........................................... 24 Tool Up for Profit!
YM-A9243........................................... 17 YU-A6411........................................... 24 www.klsupply.com
YM-A9244........................................... 17 YU-A8421........................................... 18
YM-A9245........................................... 17 YU-A8428........................................... 18 Toll Free: 800-708-3184
YM-A9246........................................... 17 YU-A8438..................................... 18, 82
YM-A9247........................................... 17 YU-A8482........................................... 18
YM-A9248........................................... 17 YU-A8840........................................... 24
YM-A9370........................................... 17 YU-A9156........................................... 24
YS-01880-A................................... 50, 77 YU-A9268........................................... 15
YU-01235............................................ 13 YU-A9374........................................... 17
YU-01256............................................ 14 YW-06355...................................... 44, 59
YU-03006............................................ 14 YW-06628............................................ 65
YU-03007............................................ 14 YW-06879...................................... 43, 50
YU-03008............................................ 14
YU-03009............................................ 14
YU-03016............................................ 14
YU-03017............................................ 14
YU-03097...................................... 12, 82
YU-03153-M................................. 44, 76
YU-03153M........................................ 61
YU-05206............................................ 11
YU-08036-C........................................ 16
YU-22912-1......................................... 13
YU-25359-A........................................ 18
YU-26900-9......................................... 16
YU-26900-12....................................... 18
YU-33223...................................... 16, 76
YU-33294............................................ 31
YU-34481...................................... 14, 18
YU-34898............................................ 12
YU-35557............................................ 13
YU-35759-A........................................ 17
YU-38411............................................ 62
YU-39951-C........................................ 16
YU-39991...................................... 12, 75
YU-44456-1......................................... 14
YU-44456-5......................................... 14
YU-44456-6......................................... 14
YU-44456-A........................................ 14
YU-88000............................................ 17
YU-A0480........................................... 15
YU-A0485........................................... 15
YU-A0490........................................... 15
YU-A0568........................................... 18
YU-A1067........................................... 18
YU-A1068........................................... 18
YU-A1069........................................... 18
800.727.6767
7 INDEX 1-800-708-3184 | kLsupply.com
General shop tools &
Equipment
SHOP TOOLS & marine engine stand
EQUIPMENT
GENERAL
• Holds all V4/V6 and Trolling Engines from all major manufacturers
2-STROKE
motors safer, with a pin locked handle and included tool tray and outrigger
2-STROKE
800.727.6767
9 GENERAL SHOP TOOLS & EQUIPMENT 1-800-708-3184 | kLsupply.com
GENERAL SHOP TOOLS & EQUIPMENT
GENERAL SHOP TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YB-06071 Driver Handle (Large) YB-06139 Flywheel
This heavy-duty handle Magneto Holder
is used with the appro- This tool holds the fly-
priate adapters to wheel magneto for tight-
remove and install seals ening and loosening of
and bearings. the flywheel nut.
1&2 CYLINDER
2-STROKE
Application: All Engines Application: All
1&2 CYLINDER
seals and bearings. Fixture consists of a
4-STROKE
steel plate with drill
Application: All Engines bushings positioned in
the correct location, cen-
terline location windows
and built-in transom
height stop.
YB-07003 Backlash
Adjustment Plate
This universal plate Application: 40~Up
bolts to the lower unit
3 CYLINDER
2-STROKE
and will accept most
magnetic dial indicator
bases for accurate lower
unit backlash checks.
3 CYLINDER
tioning kit is specifically
4-STROKE
This compresses the
valve springs for valve designed for 4-stroke
removal. There are vari- outboards. Contains
ous adapters for the the necessary cutters
different models. Use and guides.
the appropriate adapter.
Application: All
Application: All 4-Strokes
4-Strokes
4&6 CYLINDER
2-STROKE
YB-06265 Backlash
Indicator Rod
This rod clamps onto
the driveshaft to check
backlash. Use it with
4&6 CYLINDER
800.727.6767
1-800-708-3184 | kLsupply.com GENERAL SHOP TOOLS & EQUIPMENT 10
mC 800 fuel pump & tools
MC 800 FUEL PUMP & TOOLS
SHOP TOOLS &
EQUIPMENT
GENERAL
trols. An on-off switch & power indicator light complete the display. 35-8008
4-STROKE
REAR PANEL
Fuel connections, fuse access & power input are all located here.
Barbed fittings make fuel line connections fast and simple.
35-0804 - Hose
NOTE: THE MC800 Requires use of an F.I. rated fuel bottle
(35-8165) and 5/16” F.I. (high pressure) rated fuel line (18-4952).
Recommended Accessories:
3 CYLINDER
2-STROKE
TERMINAL KIT
3 CYLINDER
4-STROKE
This kit is specifically designed for marine use with tin-plated connectors
and sealed insulators. This kit is invaluable for rigging Yamaha components.
YB-37103
YB-37103-3 Bullet Plug- TIN (1WIRE) (50 PCS) A
YB-37103-4 Bullet Plug Socket- TIN (1WIRE) (50 PCS) B
YB-37103-5 Eye Connector- TIN EYE SIZE: 6.4MM (50 PCS) C
YB-37103-6 Eye Connector- TIN EYE SIZE: 6.5MM (50 PCS) D
4&6 CYLINDER
A D G J
B E H K
8 CYLINDER
4-STROKE
C F I
800.727.6767
11 GENERAL SHOP TOOLS & EQUIPMENT 1-800-708-3184 | kLsupply.com
GENERAL SHOP TOOLS
GENERAL SHOP TOOLS & EQUIPMENT
GENERAL
Part Description / Use
Number
PINION SHIM SELECTING TOOL YU-34898 High Current Shunt
The High Current Shunt
is a calibrated resistance
wire which is connected
in series with the elec-
trical accessory to be
1&2 CYLINDER
tested and plugged into
2-STROKE
a digital multimeter.
The multimeter pro-
vides a direct readout of
current draw from 0-99
amps (100-199 amps
momentary), in 0.1 amp
increments.
This tool allows the technician to determine the exact pinion gear shim Application: All.
size with a minimum of lower unit overhaul. Includes:
1&2 CYLINDER
4-STROKE
YB-34432-D
Description
YB-34432-6 Gauge Block
YB-34432-7 Gauge Block
YB-34432-8 Gauge Block
YB-34432-9 Gauge Block YU-03097 Dial Indicator
Gauge 0-5mm
YB-34432-10 Adapter Plate The Dial Indicator
3 CYLINDER
2-STROKE
YB-34432-11A Gauge Base Gauge is used for
YB-34432-19 Gauge Block measuring lower unit
YB-34432-20 Gauge Block backlash. It is to be
YB-34432-12 Instruction Sheet, Hex Head used with Adapter Plate
Cap Screw M8x1.25-6g x 20mm YB-07003 and Magnetic
Long (4) Flex Stand YU-34481.
3 CYLINDER
4-STROKE
FORWARD GEAR
SHIM SELECTING
TOOL
YB-06029-4 Pinion Gear
Bushing Installer
This tool is used to
install the pinion gear
4&6 CYLINDER
2-STROKE
bushing up into
the driveshaft housing.
It may require addi-
To determine the correct forward gear shim, it is necessary to accurately
tional adapters
measure the forward gear bearing height. This tool gives the technician a
depending on the model
means of loading the bearing to manufacturer specifications to
engine.
determine the shim size. Includes:
Application: All
YB-34446
Description
4&6 CYLINDER
4-STROKE
500-13 UNC-28
4-STROKE
ings on an outboard
1.06 o.d.x 53 i.d.x .09 thick. electrical system.
Application: All
Application: 40~Up
800.727.6767
1-800-708-3184 | kLsupply.com GENERAL SHOP TOOLS & EQUIPMENT 12
GENERAL SHOP TOOLS
GENERAL SHOP TOOLS
SHOP TOOLS &
EQUIPMENT
GENERAL
Application: All
2-STROKE
Application: All
Application: All
4-STROKE
Up to 4-1/4”
4-STROKE
Application: All
8 CYLINDER
4-STROKE
800.727.6767
13 GENERAL SHOP TOOLS & EQUIPMENT 1-800-708-3184 | kLsupply.com
GENERAL SHOP TOOLS
GENERAL SHOP TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YU-01256 Spark Plug Hole Stand YU-03006 (0 - 25mm)
Used to set engine on YU-03007 (25 - 50mm)
TDC so that the timing YU-03008 (50 - 75mm)
position can be adjusted YU-03009 (75 -100mm)
properly.
Application: All
1&2 CYLINDER
Application: All
2-STROKE
YU-44456-A Vaccumate Carb Cylinder Bore Gauge
Sync Gauge YU-03016 (18 - 35mm)
A new tool for perform- YU-03017 (35 - 150mm)
ing synchronization of Cylinder bore gauges come
carbs and throttle plates. complete with handle,
1&2 CYLINDER
Feature a battery back dial indicator and set of
4-STROKE
up and water resistant contact extensions in a
case. handsome wooden box.
Application: 4 -Strokes
Application: All
3 CYLINDER
gauge allows the vacu- Used to accomadate back-
2-STROKE
um points of all 6 cylin- lash measurements and
ders to be hooked up. runout.
Also requires 2 point
taps YU-44456-6. Application: All
Feature a battery back
up and water resistant
case.
Application: F200/225
3 CYLINDER
4-STROKE
YU-44456-5 5mm Port Taps,
(5MM) Vaccumate
6mm Port Taps,
Vaccumate
Replacement taps for
Vaccumate carb sync
gauge YU-44456-A. Also
requires two YU-44456-
10. Feature a battery
4&6 CYLINDER
back up and water resis-
2-STROKE
YU-44456-6 tant case.
(6MM)
Application: 4-Strokes
Application: All
8 CYLINDER
4-STROKE
800.727.6767
1-800-708-3184 | kLsupply.com GENERAL SHOP TOOLS & EQUIPMENT 14
GENERAL SHOP TOOLS
GENERAL SHOP TOOLS
SHOP TOOLS &
EQUIPMENT
GENERAL
a “self-centering” tip to
eliminate wandering,
even on rough surfaces.
Drill-out’s exclusive
two piece design makes
removing broken bolts a
fast and simple one step
procedure.
1&2 CYLINDER
Application: All
4-STROKE
Application: All
3 CYLINDER
2-STROKE
Application: All
0.75mm, 1.00mm,
1.25mm, 1.50mm,
1.75mm, 2.00mm,
2.50mm, & 3.00mm.
Application: All
4&6 CYLINDER
Seal Driver
Six discs fit most bear-
ing sizes. To install
(drive) seals, turn discs
over. It eliminates dam-
age to bearing races. The
seven piece kit includes
a driver handle and the
following disc sizes:
40, 45, 50, 59, 63, and
8 CYLINDER
4-STROKE
65mm.
Application: All
800.727.6767
15 GENERAL SHOP TOOLS & EQUIPMENT 1-800-708-3184 | kLsupply.com
GENERAL SHOP TOOLS & EQUIPMENT
GENERAL SHOP TOOLS & EQUIPMENT
GENERAL
Part Description / Use Part Description / Use
Number Number
YU-A5399 Oil Seal Puller with YU-08036-C #321 Digital Engine
two tips Test Tachometer
Universal seal pullers Includes inductive 10’
aid the removal in cer- inductive clip and hang-
tain applications. er handle.
SIZE: Approximately
3.375” wide x 4.625”
1&2 CYLINDER
Application: All
high x 1.250” deep
2-STROKE
POWER: (4) AAA 1.5
batteries
REPLACEMENT
PARTS & OPTIONAL
YU-26900-9 Feeler Gauge-Metric
ACCESSORIES
25 blades from 0.04mm YU-08036-C1
thru 1.0mm. Inductive Clip-10 ’
1&2 CYLINDER
Application: All
4-STROKE
YU-08036-C2
Inductive Clip-20 ‘
YU-08036-C3
Capacitive Clip-2 ‘
YU-33223 Compression Gauge
Includes 12” hose, YU-08036-C4 Vinyl
Storage Case
spark plug hole adapter
pressure gauge and air Application: All
3 CYLINDER
2-STROKE
release quick coupler.
It works on all Yamaha
YE-23400 20-Ton Hydraulic
2-stroke outboard Press
motors. • All Welded Steel
Construction
Application: 2-Strokes • Reinforced Head
Plates
• 20-ton Power Unit
3 CYLINDER
Included
4-STROKE
• Made in the U.S.A..
Application: All
YU-39951-C Digital Tachometer
A hand held digital
tachometer for
monitoring 2-stoke
engines (one through
4&6 CYLINDER
2-STROKE
four cylinders) and
4-stroke engines (one
through six and eight
cylinders). Just bring the
tachometer near
the engine and it will YE-23405 Steel “V” Block Set
For precision measuring
digitally show how and straightening opera-
fast the engine is tions. Made
4&6 CYLINDER
Application: All
8 CYLINDER
4-STROKE
800.727.6767
1-800-708-3184 | kLsupply.com GENERAL SHOP TOOLS & EQUIPMENT 16
GENERAL SHOP TOOLS & EQUIPMENT
GENERAL SHOP TOOLS & EQUIPMENT
SHOP TOOLS &
EQUIPMENT
GENERAL
Application: All
1&2 CYLINDER
4-STROKE
Lapping Compound
amount of material
The world famous green
4-STROKE
being removed.
can with the four leaf
clover. This compound
Application: 4-Strokes
kit is for seating valves,
mating gears, and
sharpening. It is sold as
a kit with coarse 120 grit
(roughing) and 280 fine
grit (finishing)
8 CYLINDER
4-STROKE
Application: 4-Strokes
800.727.6767
17 GENERAL SHOP TOOLS & EQUIPMENT 1-800-708-3184 | kLsupply.com
GENERAL SHOP TOOLS & EQUIPMENT
GENERAL SHOP TOOLS & EQUIPMENT
GENERAL
Part Description / Use Part Description / Use
Number Number
YU-A0568 Torx Key Set YE-32210 Terminal Removal Tool
This eight piece set con- This tool is designed
sists of: T9/T10/T15/ to remove wires from
T20/T25/T27/T30 & terminals without dam-
T40, high quality, black aging the end prongs.
coated “L” wrenches Includes six different
1&2 CYLINDER
with torx on both ends. shaped blades
2-STROKE
Application: All Application: All
1&2 CYLINDER
any desired length until
4-STROKE
Application: All released. Easily installed
on ceiling, wall or floor
in any central position.
Application: All
3 CYLINDER
2-STROKE
YU-A1093
Includes: 8/10/12/13/14/17 and 19mm. T-Handle features include YU-A8421
chrome vanadium tool steel deep six point sockets with a carbon YU-A8482
steel T-style handle. It is finished in nickel- pewter. The deep sockets YU-26900-12
3 CYLINDER
4-STROKE
allow for nuts to be driven over long threaded bolts. Individual Note: YU-A8438 YU-34481
Individual T-Handle sizes available, sold each.
Description
YU-A8421 Dial Indicator Gauge with Magnetic Base
YU-A1067 8mm YU-A8428 Stand 2-1/4” Dial Indicator Gauge only, 0”
YU-A1068 10mm YU-26900-12 - 2-1/4” range in .001” increments Indicator
YU-A1069 12mm YU-A8438 Magnetic Base Stand only
YU-A1072 13mm YU-34481 Flexible Magnetic Dial Indicator Stand
4&6 CYLINDER
YU-A1073 14mm
2-STROKE
YU-A1074 17mm Application: All
YU-A1087 19mm
YU-A1104 T-Handle Rack (10 Slots)
800.727.6767
1-800-708-3184 | kLsupply.com GENERAL SHOP TOOLS & EQUIPMENT 18
BATTERY CHARGERS
BATTERY CHARGERS
SHOP TOOLS &
EQUIPMENT
GENERAL
35-0784
1&2 CYLINDER
2-STROKE
35-1416
3 CYLINDER
4-STROKE
37-0782
37-0783
4&6 CYLINDER
4-STROKE
800.727.6767
19 GENERAL SHOP TOOLS & EQUIPMENT 1-800-708-3184 | kLsupply.com
BATTERY CHARGERS
BATTERY CHARGERS
GENERAL
1&2 CYLINDER
2-STROKE
35-8006
1&2 CYLINDER
• Deactivates when disconnected.
OPTIMATE PRO 8 BATTERY CHARGER
4-STROKE
• Electronically protected reverse polarity connection
• Quickly recovers neglected batteries The new Optimate PRO 8 is a highly versatile 6/12V battery-care
• Includes clips for wall mounting center for up to 8 batteries at a time. Compatible with all lead-acid
Complies with California’s NEW Appliance Efficiency Program. models, GEL, MF-AGM or conventional, the new Optimate PRO 8
35-8006 Optimate Pro -S Desulfating Battery Charger/Maintainer can be used on starter batteries, as well as on industrial, motive or
stationary-oriented types. Just connect up to 8 (even dissimilar) bat-
teries, and these will be individually taken through Optimate’s widely
acclaimed multi-stage program: Desulfation (if necessary), constant
current bulk charge, verification, final test & limitless maintenance.
Countless connection variations are possible, either enhancing charge
3 CYLINDER
2-STROKE
current for larger batteries, or handling series-connected blocks, or
both. Combinations up to 8A or 96V are possible. State-of-the-art diag-
nostics, charging, testing and recovery of otherwise “dead” batteries”,
all in a single device.
• Charges up to 8 batteries at the same time.
35-7842 • For 6 and 12V batteries STD, AGM, Deep Cycle.
• Automatically recovers deep-discharged batteries.
• Battery test and self-discharge check.
• Keeps batteries fully charged at all times.
OPTIMATE PRO2 BATTERY CHARGER Complies with California’s NEW Appliance Efficiency Program.
3 CYLINDER
4-STROKE
This shop charger has two independent charging systems of 2Amps 35-7997 Optimate PRO 8 Battery Charger
that are able to desulfate, charge, maintain & initialize new batteries 35-8317 Optional Wall Mount Bracket
using the 12 hour program. Simply connect a battery and the rest is 35-7744 PRO 8 Replacement leads
automatic. 2 x 12V OR 1 x24V system.
Complies with California’s NEW Appliance Efficiency Program.
35-7842 OPTIMATE PRO2 Battery Charger
4&6 CYLINDER
2-STROKE
35-8316
4&6 CYLINDER
4-STROKE
800.727.6767
1-800-708-3184 | kLsupply.com GENERAL SHOP TOOLS & EQUIPMENT 20
SHOP TOOLS & BATTERY CHARGERS
EQUIPMENT
GENERAL
1&2 CYLINDER
2-STROKE
35-0168
35-7342
1&2 CYLINDER
NEW FEATURES:
2-STROKE
OPTIMATE 6
BATTERY CHARGER/
MAINTAINER
The world’s most advanced
diagnostic battery optimizer, now
with 5A charge current!
4&6 CYLINDER
2-STROKE
240Ah. The multi step charging system is suitable for any type of 12V
solution for long term maintenance of 12V batteries in any vehicle /
4-STROKE
lead-acid battery. During the 24/7 auto storage control the battery is
craft that is stored in or outdoors.
tested every hour and recharged as necessary. With a 30 minute rest
Optimate 2 is weatherproof, very easy to use, simply connect to the
each hour.
battery and plug it into the nearest power socket, the rest is fully
The universal input system accepts AC power between 100 to
automatic. With 0.8A constant current Optimate 2 automatically brings
240VAC (incl. generator / inverter).
the battery to full charge and then switches to the unique Optimate
• Max Input Current 2.5 Amps @ 120V
battery saving maintenance charge mode to keep the battery at 100%
• Saves neglected batteries other chargers can’t
ready and at the same time provides power to the on board computer,
• Optimizes battery power and life
display or anti theft alarm. Recommended for STD (with remov-
• 24/7 automatic storage control
able filler caps), sealed AGM (absorbed glass mat) & sealed GEL 12V
• Early warning of battery problems
8 CYLINDER
800.727.6767
21 GENERAL SHOP TOOLS & EQUIPMENT 1-800-708-3184 | kLsupply.com
MULTIMETER
GENERAL
BATTERY HYDROMETER
37-8347
1&2 CYLINDER
2-STROKE
Battery Hydrometer
Used to check the battery specific gravity.
YU-03036
Application: All
1&2 CYLINDER
MULTIMETER WITH TACHOMETER
4-STROKE
3 CYLINDER
2-STROKE
SAND BLAST CABINET WITH DUST COLLECTOR
Fluke Model 88 Multimeter with Tachometer Top and side door opening. Thick 18 gauge steel wall construction
This multimeter’s features include volt, ohm, amp, continuity and with steel legs. Cabinet is 37” wide x 25” depth x 59” height.
diode tests, rpm measurements with the provided inductive pickup, Window measures 7” x 18”. Uses 110V power. Trigger gun operation,
minimum/maximum/average recording of measurements, frequency 14CFM @ 90-100psi. Made in U.S.A. Shipping weight 175 lbs.
and duty cycle measurements, low-ohms function, millisecond pulse 37-8347 Sand Blast Cabinet
width measurements, and smoothing (shows an averaged reading of
3 CYLINDER
measurements which fluctuate such as rpm). Included accessories: OPTIONAL ACCESSORIES for 37-8347
4-STROKE
holster, inductive pickup, hard carrying case, test leads, test probes, 35-5842 Aluminum Oxide-Fast cutting, hard - 50 lbs
large alligator clips, users manual and quick reference guide. 35-8329 Glass Beads-Light, dust free - 50 lbs
YU-A1927 37-8356 Glass Bead Media-100/170 grit - 50 lbs
35-8531 Recoil Air Hose, 12’ length, yellow
Application: All 35-8533 Recoil Air Hose 25’ length, yellow with swivels
ANALOG MULTIMETER
4&6 CYLINDER
2-STROKE
4&6 CYLINDER
4-STROKE
Application: All
800.727.6767
1-800-708-3184 | kLsupply.com GENERAL SHOP TOOLS & EQUIPMENT 22
ULTRASONIC CLEANER
ULTRASONIC CLEANER
SHOP TOOLS &
EQUIPMENT
GENERAL
37-3614:
7 Seven Gallon Cleaner
1&2 CYLINDER
2-STROKE
35-6671
35-6674
35-6675 Basket only
• Fully insulated stainless steel tank 35-6675 9” W x 8” H basket only-Lid not included. Sold as an option.
4-STROKE
• Self-Draining Basket (Optional) 35-6677 Lid for 9” x 8” basket only. Not included with 35-6675.
• Adjustable thermostatically controlled heat
• Limited 2yr parts and labor warranty
CREST SOAP for ULTRASONIC CLEANER
37-3612 K&L 1.5 Gallon Compact ultrasonic cleaner
Tank Size: 11.75” L x 6” W x 6” D
37-3613 Basket for 1.5 Gallon Cleaner
37-3617 K&L 3.25 Gallon Benchtop Cleaner
Tank Size: 11.75” L x 9.5” W x 8” D
3 CYLINDER
for use in K&L Pro 1911, 7.5 Gallon Benchtop Cleaner 38-2950 Crest CC2003 Soap for Ultrasonic Cleaners is designed to
38-2950 Crest CC2003 Soap for Ultrasonic Cleaners is designed to work in 130-160 degree temps for carbs & fuel injection
work in 130-160 degree temps for carbs & fuel injection One gallon of soapmakes 10.5 gallons of solution
One gallon of soapmakes 10.5 gallons of solution 38-2376 CC235 - Soap for Ultrasonic Cleaners.
Important Note: These are Benchtop cleaners and are NOT intended for (6 oz soap to 1 gallon of water.)
continuous (All-day) duty. Please contact K&L for information on Industrial 38-2378 Crest CC211 Soap for Ultrasonic Cleaners
models that are designed for continuous (All-day) duty. One gallon of soapmakes 21 gallons of solution
4&6 CYLINDER
2-STROKE
800.727.6767
23 GENERAL SHOP TOOLS & EQUIPMENT 1-800-708-3184 | kLsupply.com
GENERAL SHOP TOOLS & EQUIPMENT
GENERAL SHOP TOOLS & EQUIPMENT
GENERAL
Part Description / Use Part Description / Use
Number Number
YE-A9042 Fluid Evacuator YU-A8840 K&L Deluxe Apron
The Fluid Evacuator is a Made of quality black
portable, hand operated cloth with K&L logo
transfer system with imprinted in white on
a 6.5 liter (1.7 gallon) front. Storage pockets
capacity. The reservoir included.
1&2 CYLINDER
is made of polyethene
2-STROKE
and can safely hold oil, Application: All
coolant, and brake fluid.
Application: All
1&2 CYLINDER
Deluxe Barrel Pump Measures in ounces and
4-STROKE
cc’s. Use for filling forks,
YE-A4777 • Adjusts to quarts or
liters per single stroke • shocks, engine oil, etc.
No drip recovery Also has mixing ratio
• Eliminates messy oil scale for accurate oil/
drums gas premix. Sold each.
• Includes Telescoping Note: Lid is an add-on,
suction tube not included with Ratio
• Smooth, easy pump Rite.
action
Application: All
3 CYLINDER
• For oils, fuels and
2-STROKE
non-corrosive solvents
Application: All
3 CYLINDER
surface area
4-STROKE
permits drainage of handle. The blades
multiple contain- are easily changed by
ers simultaneously. depressing the locking
Highly durable, it will button. Also useful for
resist rust, dents and chamfering of small
other chemicals and holes in metal.
give many years of
troublefree service. Fits Application: All
all types of 55 gallon
4&6 CYLINDER
drums.
2-STROKE
YU-A6375
Application: All 10m T-Handle Spark
Plug Wrench
Spill Pan, Black
(bottom of photo) YU-A6411
8” height x 32-1/2” 12mm T-Handle Spark
diameter Spill Pan is Plug Wrench
constructed of heavy-
duty polyethylene that
4&6 CYLINDER
YU-A6410
4-STROKE
Application: All
Tool Up for Profit!
www.klsupply.com
Toll Free: 800-708-3184
800.727.6767
1-800-708-3184 | kLsupply.com GENERAL SHOP TOOLS & EQUIPMENT 24
MC800 REGULATED FUEL PUMP
K & L GENUINE SHOP EQUIPMENT
MC800 REGULATED FUEL PUMP FOR F.I.
Fuel Injection is here to stay, and with it has come the need for
new diagnostic tools. A controllable fuel supply is mandatory
to accurately service these bikes; the MC800 from K&L Supply
is the answer.
Application: 4,5
YB-06014 Bearing Installer
Forward Gear Bearing
It installs the forward YB-06178 Bushing Remover
It removes the upper
gear bearing and the
driveshaft bushing. Use
driveshaft oil seals. It is
used with Driver Handle it with Slide Hammer
YB-06229. YB-06096.
Application: 4,5
1&2 CYLINDER
Application: 2,4,5
4-STROKE
Application: 8
YB-06029 Pinion Gear Bushing
Installer YB-06015 Bearing Installer
This tool installs the pin- Reverse Gear Bearing
ion gear bushing up into It installs the reverse
the driveshaft housing. gear ball bearing. Use
it with Driver Handle
Application: 2,4,5,8 YB-06071.
4&6 CYLINDER
Application: 8, 9.9,15
2-STROKE
800.727.6767
27 1&2 CYLINDER 2-STROKE 1-800-708-3184 | kLsupply.com
LOWER UNIT TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YB-06234 Water Pump YB-06231 Driveshaft Needle
Mechanical Seal Bearing Installer
Installer It properly installs the
When used with a driveshaft needle
universal puller (such as bearing. Use it with Pilot
YB-06117), these hooks YB-06230 and Driver
1&2 CYLINDER
will properly remove Handle YB-06229.
2-STROKE
the reverse gear
bearing housing and Application: 9.9,15
propeller shaft. Includes:
YB-06234-1 Hook
Assembly, YB-06234-2
Hook Assembly, Heavy YB-06022 Oil Seal Installer
Duty Washers (2), and It installs the double
M6 x 1.0 Hex Nuts (2). oil seals on the
driveshaft. Use it
1&2 CYLINDER
Application: 8,9.9,15 with Driver Handle
4-STROKE
YB-06071.
Application: 9.9,15
3 CYLINDER
2-STROKE
(Forward Gear) It removes and installs
It drives in the forward the pinion nut for
bearing outer race. Use driveshaft removal.
it with Driver Handle
YB-06071.
Application: 9.9,15
Application: 9.9,15
3 CYLINDER
It is required to select
4-STROKE
Pinion Nut Torque
Tool the proper pinion gear
It is used to loosen or shims. It eliminates the
torque the pinion nut. trial and error method
It installs onto the of disassembly and
driveshaft. reassembly of the
bearings and races
Application: 9.9,15 repeatedly to
determine the cor-
rect shim. Includes:
4&6 CYLINDER
YB-34232-1 Bearing
2-STROKE
Plug Assembly,
YB-34232-2 Shim
YB-06230 Driveshaft Needle (Gauge Pinion Height),
Bearing Installer YB-34232-4 Bearing
and Remover Gauge, YB-34232-5
Removes and installs Instruction Sheet.
the driveshaft needle
bearing. Use it with Application: 9.9,15
Guide YB-06231 and
4&6 CYLINDER
or surrounding areas.
4-STROKE
Application: ALL
MODELS
POWER HEAD
SHOP TOOLS &
EQUIPMENT
GENERAL
Application: F2.5
YM-08035-A Valve Adjuster
It includes 3 & 4mm
YB-06801 Valve Guide Remover hex. It is designed to
It is used to remove the help with critical valve
valve guides from the clearance adjustments.
cylinder head.
1&2 CYLINDER
Application: F9.9
4-STROKE
Application: F2.5
voltage output.
guide
Application: F25/T25
Application: F2.5
GENERAL
Part Description / Use Part Description / Use
Number Number
YB-06085 Bearing Housing Oil YB-06298 Driveshaft Needle
Seal Installer Bearing Installer/
It is used to install Remover
shims and outer bear- The attachment is used
ing race for the forward for the removal and
gear. It also requires the installation of the drive-
1&2 CYLINDER
use of Driver Handle shaft lower needle bear-
2-STROKE
YB-06071. ing. Use it with Driver
Handle YB-06229.
Application: F2.5
Application: F9.9
YB-06230 Needle Bearing
Remover & Installer
Removes and installs the
driveshaft needle bear-
ing. Use it with Guide
1&2 CYLINDER
YB-06231 and Driver YB-06299 Pinion Bearing
4-STROKE
Handle YB-06229. Shim Selector
It is used to aid in shim
Application: F2.5 selection for the pinion
gear.
YB-06028 Driveshaft Bushing
Application: F9.9
Remover & Installer
It properly removes
and installs the drive-
shaft bushing. Use it
3 CYLINDER
2-STROKE
with Driver Handle
YB-06229.
Application: F2.5
3 CYLINDER
4-STROKE
YB-06014 Bearing Installer YB-06344 Forward Gear
Forward Gear Bearing Shim Gauge
It installs the forward This gauge is used to
gear bearing and the help get an accurate
driveshaft oil seals. It shim height for the
is used with Driver forward gear.
4&6 CYLINDER
Handle YB-06229.
2-STROKE
Application: F25
Application: F2.5
Application: F2.5
8 CYLINDER
4-STROKE
Application: F25/T25
YB-06168 Oil Seal Installer
It is used to install the
propeller shaft seals YB-06231 Driveshaft Bearing
in the bearing hous- Depth Plate
ing. It must be used Required for setting
1&2 CYLINDER
Application: F25
3 CYLINDER
2-STROKE
YB-06071.
Application: F25
Application: F25
800.727.6767
33 1&2 CYLINDER 4-STROKE 1-800-708-3184 | kLsupply.com
LOWER UNIT TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YB-06270-A Forward Gear Bearing YB-06175-2B Trim Cylinder Wrench
Installer The Trim Cylinder
This adapter is used to Wrench is specially
install the forward gear designed to remove
tapered roller and reinstall the trim
bearing. cylinder end cap.
1&2 CYLINDER
2-STROKE
Application: T25 Application: F25
1&2 CYLINDER
Driver Handle YB-06071 Yamaha 2 & 4 stroke
4-STROKE
and Driveshaft Bearing outboard motors with-
Depth Plate YB-34473 out damage to the screw
are required. or surrounding areas.
For removal, Driver
Handle YB-0671 is Application: ALL
required. MODELS
Application: T25
3 CYLINDER
2-STROKE
YB-41446 Forward Gear Outer
Race Installer
It is used with Driver
Handle YB-06071 to
properly install forward
3 CYLINDER
gear shims and outer
4-STROKE
bearing race.
Application: T25
4&6 CYLINDER
2-STROKE
YB-34473 Driveshaft Bearing
Depth Plate
The depth plate is used
with Driveshaft Bearing
Installer/Remover
YB-06063 and Driver
Handle YB-06071 to
properly set the
4&6 CYLINDER
driveshaft lower bearing
4-STROKE
depth.
Application: T25
Application: F25
Oil Filler Cap Installer/Remover Tool was designed Oil Drain Screw Tool was designed to remove and
to easily remove and install the oil cap on Yamaha install the oil drain plug screw for all outboard motors
outboard motors without damaging the cap. without damaging the screw or surrounding area.
Difficult to Remove Installing & Removing Difficut to Remove Installing & Removing
by Hand Oil Filler Cap Oil Drain Screw Tool Oil Drain Screw Tool
Installing & Removing Installing & Removing Installing & Removing Installing & Removing
Oil Filler Cap Oil Filler Cap Oil Drain Screw Tool Oil Drain Screw Tool
YB-06229.
YB-06346 Needle Bearing
Application: 25,30
Remover and Installer
It is used to remove and
install the driveshaft
needle bearing. Use it
with Driver Handle
YB-06229. YB-06079-A Driveshaft Holder
Pinion Nut
1&2 CYLINDER
Torque Tool
Application: 30
4-STROKE
Application: 30
3 CYLINDER
2-STROKE
Application: 25,30
Application: 60,70
4&6 CYLINDER
4-STROKE
YU-34899-A Digital
Multimeter to check
peak voltage output.
800.727.6767
37 3 CYLINDER 2-STROKE 1-800-708-3184 | kLsupply.com
LOWER UNIT TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
1&2 CYLINDER
shaft.
2-STROKE
Application: 25
YB-06075 Gland Nut Wrench
It removes and installs
the lower gland nuts. It YB-06400 Reverse Gear Shim
is designed specifically Gauge
for Yamaha motors. It is used for selecting
proper reverse gear
Application: 25,30 shims.
1&2 CYLINDER
Application: 25,
4-STROKE
1988 ~ up
YB-06167 Bearing Cup Installer
It installs the driveshaft
bearing cup on 25 and YB-34232-C Pinion Height Gauge
Block
30 engines. It installs the
It is required to select
forward gear bearing on
the proper pinion, for-
4, 5, and 8 engines.
ward gear, and reverse
Use it with Driver
gear shims. It elimi-
Handle YB-06071.
nates the trial and error
3 CYLINDER
2-STROKE
method of disassembly
Application: 25,30
and reassembly of the
bearings and races
YB-06168 Bearing Seal Installer repeatedly to deter-
It installs the reverse mine the correct shim.
gear housing oil seals. Includes:
Use it with Driver YB-34232-1 Bearing Plug
Handle YB-06071. Assembly, YB-34232-2
Shim (Gauge Pinion
Application: 25,30 Height), YB-34232-
3 CYLINDER
4-STROKE
4 Bearing Gauge,
YB-06169 Needle Bearing YB-34232-5 Instruction
Installer Sheet.
It installs the reverse
gear bearing housing Application: 25,30
oil seal and is used as
a guide to install the
driveshaft needle bear- YB-39799 Reverse Gear Shim
Gauge
ing with tools YB-06071
4&6 CYLINDER
It is used for selecting
and YB-06168. It is also
2-STROKE
the proper reverse gear
used with Bushing
shims.
Installer YB-06029 for
driveshaft bushing
Application: C30
installation.
1993 ~up
Application: 25,30 YB-06344 Shim Gauge
It is used for selecting
proper forward and
YB-06234 Bearing Housing
reverse gear shims.
4&6 CYLINDER
Puller
4-STROKE
Application: 25,30
Application: 40,50
2-STROKE
Application: 30
Application: 40,50
4-STROKE
Application: 30
Application: 30
Application: 40,50
YB-06071. YB-06071.
800.727.6767
39 3 CYLINDER 2-STROKE 1-800-708-3184 | kLsupply.com
LOWER UNIT TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YB-06269 Water Pump Housing YB-06153 Bearing Housing
Bearing and Seal Needle Bearing
Installer Remover
It properly installs the It is required to remove
water pump seal on 70 the needle bearing from
and 90 models. It installs the reverse gear
1&2 CYLINDER
the rear bearing housing housing.
2-STROKE
seal on 40, 50, 70, and
90 models. Application: 70, 75, 80,
85, 90
Application: 40~90
1&2 CYLINDER
Handle YB-06071. bearing. Use it with
4-STROKE
YB-34474.
Application: 50 1995
Application: 70, 75, 80,
85, 90
3 CYLINDER
2-STROKE
the driveshaft needle taper roller bearing. Use
bearing. Use it with it with Driver Handle
YB-34473. YB-06071.
3 CYLINDER
4-STROKE
Torque Tool driveshaft needle
It is used to loosen or bearing is installed to
torque the pinion nut. its proper depth. Use
It installs onto the it with Driver Handle
driveshaft. YB-06063.
4&6 CYLINDER
YB-06152 PTT/MIDSECTION TOOLS
2-STROKE
Bearing Housing
Puller
Part Description / Use
Bearing Housing Needle
Number
Bearing Installer.
YB-34466 Power Tilt Cylinder
Application: Cap Wrench
70, 75, 80, 85, 90 It loosens and tightens
the power tilt cylinder
cap. 4&6 CYLINDER
4-STROKE
Application: C40, 50
YB-06276-B Forward Gear Bearing
Cup Installer
Installs the forward
gear bearing cup. Use
with Driver Handle
YB-06175-2B Power Tilt Cylinder
YB-06071. Cap Wrench
It loosens and tightens
Application: 70, 90 the power tilt cylinder
cap.
8 CYLINDER
4-STROKE
Application: 40-90
The new K&L PTT Cap Tool Kit will change the way you remove/install trim and tilt caps forever. Our unique
patent pending design allows for torque to be applied down into the center of the cap. This prevents tool
slippage and eliminates the possibility of damaging the tool, cap or engine.
KIT INCLUDES ADAPTERS FOR ALL YAMAHA TRIM AND TILT CAPS
Tilt Cap Adapters Feature A Split Design For Installation Trim Cap Adapters Slide Easily Over The Trim Shaft.
Onto The Cap And Shaft.
Tilt Cap Socket Fits Securely Over The Adapter For Socket Fits Securely Over The Adapter For
Easy Removal With An Impact Wrench. Removal With An Impact Wrench.
SETTING
SETTING THE
THE LEADING
LEADINGTHE
THEPOWERSPORTS
POWERSPORTSINDUSTRY
INDUSTRYININSHOP
SHOP
STANDARD,
STANDARD,
SINCE
SINCE 1968.
1968. EQUIPMENT,TOOLS
EQUIPMENT,TOOLSAND
ANDHARD
HARDPARTS.
PARTS.
EMPOWERED BY EXCELLENCE INNOVATION
3 CYLINDER
SETTING THE 4-STROKE
LEADING THE POWERSPORTS INDUSTRY IN SHOP
STANDARD,
SINCE 1968. EQUIPMENT,TOOLS AND HARD PARTS.
POWER HEAD TOOLS
POWER HEAD TOOLS
SHOP TOOLS &
EQUIPMENT
GENERAL
Output.
Application: F30, F40
Application: F30, F40
YB-06795 Diagnostic
Indicator Test
YM-04019 Valve Spring The indicator light is
Compressor used to identify an
It is used with the valve engine self-diagnostic
spring compressor with warning code.
1&2 CYLINDER
800.727.6767
43 3 CYLINDER 4-STROKE 1-800-708-3184 | kLsupply.com
POWER HEAD TOOLS
POWER HEAD TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YB-06946 Fuel Pressure YB-06079 Driveshaft Holder
Gauge Adapter It is used to hold the
It attaches between the driveshaft to allow for
fuel pump and injector pinion nut removal or
rail when used with installation.
fuel pressure gauge
1&2 CYLINDER
YU-03153M Application: F30, wF40
2-STROKE
Application: F30, F40
1&2 CYLINDER
between the fuel pump upper bearing outer
4-STROKE
and injector rail when race.
used with the YB-06946
fuel pressure gauge Application: F30, F40.
adapter. Attach this new
tool to the fuel system
and obtain an accurate YB-06112 Bearing Housing
fuel pressure reading. Bearing/Oil Seal
When you are finished Remover
place the small clear fuel When used with Driver
3 CYLINDER
pressure relief hose into Handle YB-06071, this
2-STROKE
the fuel tank or appropi- adapter is designed to
ate container and push remove the propeller
the fuel release button. shaft bearing carrier
bearing and seals.
Application: F30, F40
Application: F30, F40
YW-06355 Crankshaft Holder
It is used to hold or
rotate the crankshaft
when working on the
3 CYLINDER
4-STROKE
engine.
Application: F30, F40
YB-06111 Bearing Housing
Bearing/Installer
When used with Driver
Handle YB-06071, this
attachment will prop-
erly install the propeller
shaft bearing housing
4&6 CYLINDER
YM-01196 Valve Guide Reamer
bearing.
2-STROKE
It is designed to clean
out combustion deposits
Application: F30, F40
from inside the valve
guide.
Application: F30, F40
Installer
It is used with Driver
It removes and installs
Handle YB-06071 to
the driveshaft needle
properly install the oil
bearing. Use it with
seals in the Drive Shaft
YB-34473.
Oil Seal Housing.
Application: F30, F40
Application: F30, F40
4&6 CYLINDER
2-STROKE
800.727.6767
45 3 CYLINDER 4-STROKE 1-800-708-3184 | kLsupply.com
PTT/MIDSECTION TOOLS
PTT/MIDSECTION TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YB-06234 Bearing Housing YB-06175-2B Trim Cylinder Wrench
Puller This wrench is specially
When used with a uni- designed to remove and
versal puller (such as install the trim cylinder
YB-06117), these hooks end cap.
will properly remove
1&2 CYLINDER
the reverse gear bear- Application: F30, F40
2-STROKE
ing housing and pro-
peller shaft. Includes:
YB-06234-1 Hook
Assembly, YB-06234-2
Hook Assembly, Heavy
Duty Washers (2), and
M6 x 1.0 Hex Nuts (2).
1&2 CYLINDER
Application: F30, F40
4-STROKE
YB-06668 Pinion Height Gauge
New procedures have
been developed for
shimming the F40 lower
unit. Refer to F40 service
manual lit-18616-03-15
for detailed procedural
3 CYLINDER
information. Refer to
2-STROKE
tech exchange # 02012-
004 for additional infor-
mation.
3 CYLINDER
4-STROKE
Puller YB-06117. It is
used to remove the
reverse gear retainer.
YB-06349 Crankshaft
Seal Installer
4&6 CYLINDER
It is used to install lower
2-STROKE
crankshaft seal. Use
it with Driver Handle
YB-06071.
4&6 CYLINDER
4-STROKE
Handle YB-06229.
Tilt The Cap For Place Adapter On The Place Adapter Into Slide Trim Cap Socket
Easy Removal Trim Cap The Trim Cap Over Adapter
Slide Trim Cap Socket Place Impact Wrench Into Secure Socket On Attach Impact Gun Into The
Over The Adapter Socket & Remove Cap The Adapter Socket & Remove The Cap
sensor adjustment.
Application: V4, 2.6L Note: Voltmeter must
read output as low as
0.41 volts.
YB-06205 Crankshaft
Bearing Installer
It removes and installs Application: 2.6L, 220,
the crankshaft upper 225, 1994 ~ 89
roller bearing. It is used
with a press to remove
the bearing and has a
3 CYLINDER
Test Harness
4-STROKE
800.727.6767
49 4&6 CYLINDER 2-STROKE 1-800-708-3184 | kLsupply.com
POWER HEAD TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YB-06795 Diagnostic Test Lead YW-06879 Pulsar Coil
Updated YB-06444 Test Harness
The indicator light is It is used with a DVA
used to identify an meter and the Peak
engine self-diagnostic Voltage Adapter
warning code. YU-39991. This test har-
1&2 CYLINDER
ness is used to measure
2-STROKE
Application: 2.6L, 3. 1L, output voltage.
3.3L
Application: HPDI
1&2 CYLINDER
is used to measure out-
4-STROKE
Application: OX66, 2.6L put voltage.
HPDI
Application: HPDI
3 CYLINDER
Application: OX66,
2-STROKE
of output voltage
HPDI
Application: HPDI
3 CYLINDER
YU-39991 to measure
4-STROKE
ment of output voltage.
output voltage.
Application: OX66,
HPDI Application: HPDI
4&6 CYLINDER
It is used with a DVA removal or installation
2-STROKE
meter. This harness of the pulley
allows for the measure- mounting nut.
ment of output voltage.
Application: HPDI
Application: OX66,
HPDI YB-06442 Engine Lifting Hook
It threads onto the
crankshaft threads to
allow for lifting.
4&6 CYLINDER
4-STROKE
Application: 3.3L
Application: V4
2-STROKE
Application: V4,V6
Application: V4, V6
YB-06194 Driveshaft Needle
Bearing Installer
3 CYLINDER
and Remover
2-STROKE
Application: V4, V6
Handle YB-06071.
Application: V4, V6
800.727.6767
51 4&6 CYLINDER 2-STROKE 1-800-708-3184 | kLsupply.com
POWER HEAD TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YB-06377 Spacer Installer YB-06258 Forward Bearing
Use it with Driver Race Installer
Handle YB-06071 to It installs the forward
properly install reverse gear bearing outer
gear spacer. race. Use it with Driver
Handle YB-06071.
1&2 CYLINDER
Application: Counter
2-STROKE
Rotation V4 Application: V6
1&2 CYLINDER
Application: Counter both needle bearings
4-STROKE
Rotation V4 to their proper depth.
Use with Driver Handle
YB-06201 Driveshaft YB-06071.
Holder-Pinion Nut
Torque Tool Application: V6
Use it to loosen or
torque the pinion nut. It
installs onto the
driveshaft.
3 CYLINDER
2-STROKE
Application: V4, V6, YB-34449-A Driveshaft Puller
It slides over the drive-
F200/225, 2.6L, 3.1L,
shaft and locks against
3.3L
the driveshaft key.
Thread in Slide Hammer
YB-06207 Bearing Housing
Puller YB-06096 and remove
When used with a uni- the driveshaft from the
versal puller (such as pinion gear.
YB-06117), these hooks
3 CYLINDER
Application: V6
4-STROKE
will properly remove
the reverse gear
bearing housing and
propeller shaft. Includes:
YB-06207-1 Hook
Assembly, YB-06207-2 YB-34453 Forward Gear &
Hook Assembly, Heavy Tapered Roller Bearing
Duty Washers (2), and Separator
M8 x 1.25 Hex Nuts (2). It separates the forward
gear from the forward
4&6 CYLINDER
gear bearing without
2-STROKE
Application: V4, V6, 2.
6L, 3.1L, 3.3L damaging the gear or
bearing. It is used with
a suitable pilot and a
YB-06052 Shift Rod Push Arm press.
It shifts the lower unit
into forward, neutral or Application: V-6 except
reverse when the lower D150/ DX150
unit has been removed
from the engine.
4&6 CYLINDER
4-STROKE
Application: V6
Application: D150,
DX150
YB-06436 Bearing Separator
It is designed to help
YB-42227 Propshaft End Seal remove the bearing
Bearing Driver from the forward gear.
It is used with Driver
4&6 CYLINDER
Application: D150,
DX150
YB-06437 Bushing Remover/
Installer
It is used with Driver
YB-42229 Bearing Driver Handle YB-06071 to
4&6 CYLINDER
installation.
4-STROKE
Application: 3.1L
800.727.6767
53 4&6 CYLINDER 2-STROKE 1-800-708-3184 | kLsupply.com
LOWER UNIT TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YB-06439 Shim Gauge YB-06435 Needle Bearing
It is used to help proper- Installer
ly select the shim height Use it with the Needle
or the forward gear. Bearing Installer/
Remover YB-06213 and
Application: 3.1L (RH) Pinion Gear Bushing
1&2 CYLINDER
Installer YB-06029-4
2-STROKE
to properly install the
YB-06440 Shim Gauge outer race of the lower
It is used to properly driveshaft bearing.
measure the forward
gear to determine the Application: 3.1L, 3.3L
accurate shims.
YB-06441 Pinion Gear
Application: 3. 1L, Shim Gauge
LZ250 3. 3L, (LH) It is used to determine
1&2 CYLINDER
shim measurement of
4-STROKE
the pinion gear.
YB-06048 Gland Nut Wrench
It removes and installs Application: 3.1L, Z250
lower gland nuts. It is 3.3L
designed specifically
for Yamaha motors. It is
manufactured from high
YB-41707 Reverse Gear
strength alloy steel and Bearing Remover
heat-treated for strength Use it with Universal
3 CYLINDER
and durability.
2-STROKE
Puller YB-06117. It is
used to remove the
Application: Counter reverse gear retainer.
Rotation 3.1L
Application: Counter
YB-06430 Forward Bearing Rotation 3.1L, 3.3L
Installer
Use it with Driver YB-06168 Oil Seal Installer
Handle YB-06071 to Use it with Driver
install the reverse gear Handle YB-06071 to
3 CYLINDER
4-STROKE
bearing in the bearing remove propeller shaft
housing. bearing housing bearing
and seals.
Application: 3. 1L, 3.3L
Application: 3.3L
4&6 CYLINDER
Oil Seal Installer
Use it with Driver
It is used with Driver
2-STROKE
Handle YB-06071 to
Handle YB-06071 to
properly install the
install seals for the
forward gear outer
driveshaft housing and
bearing race.
install propeller shaft
bearing housing seals.
Application: 3. 1L, 3.3L
Application: 3.1L, 3.3L
YB-06109
4&6 CYLINDER
Bearing Outer
4-STROKE
Race Attachment
YB-06434 Needle Bearing It is used to properly
Installer install the reverse gear
Use it with Driver into the bearing
Handle YB-06071 to housing.
remove/install the
needle bearing into Application: 3.3L
reverse gear retainer.
(LH)
bearing.
2-STROKE
Application: VZ225/250
Application: 3.3L 3.3L
(LH)
4-STROKE
Application:
VZ225/250 3.3L
800.727.6767
55 4&6 CYLINDER 2-STROKE 1-800-708-3184 | kLsupply.com
PTT/MIDSECTION TOOLS
PTT/MIDSECTION TOOLS
GENERAL
Part Description / Use
Number
YB-06548 Tilt Wrench,
Showa System
It is specially designed
to remove the end caps
on the tilt cylinders.
1&2 CYLINDER
Application:
2-STROKE
Application: 1997 & Up,
V4, V6 2.6L, VX200/
2253.1L, 3.1L
1&2 CYLINDER
4-STROKE
Application: 3.3L
3 CYLINDER
2-STROKE
cylinder end cap service.
3 CYLINDER
4-STROKE
YB-06581 PTT Pressure
Gauge Adapter
It is used with the
PTT Pressure Gauge
YB-06580 to measure
operational pressure of
the PTT system.
4&6 CYLINDER
Application: 3.1L, 3.3L
operational pressure of
the PTT system.
37-8449
V4/V6 Marine Engine Stand
37-8449
F40-4 ~ F/T50
Application: F75~ F115
YB-06871 Rectifier/Regulator
Test Harness
It is used with a DVA YB-06872 Test Harness 6 PIN
meter to test the voltage It is used with a DVA
output. meter and the Peak
Voltage Adapter
Application: F/T50 YU-39991 to measure
3 CYLINDER
voltage output.
4-STROKE
Application:
2-STROKE
Application: All
MODELS
800.727.6767
59 4&6 CYLINDER 4-STROKE 1-800-708-3184 | kLsupply.com
POWER HEAD TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YB-06791 Pulser Coil Test Lead YB-06793 Throttle Position
It is used with a DVA Sensor Test Lead
meter and the Peak Used with a DVA meter
Voltage Adapter to measure and adjust
YU-39991 to measure throttle position sensor
voltage output. voltage.
1&2 CYLINDER
NOTE: DVA meter must
2-STROKE
Application: F115 be able to read 0.40
volts.
YM-04064-A Valve Guide
Remover/Installer
Application: F115~ F225
It is specifically
designed to remove and YB-06861 Injector Test Lead
install the valve Used with a DVA meter
guides from the cylinder to measure output volt-
head. age.
1&2 CYLINDER
Application: F115 Application: F115~ F225
4-STROKE
YB-06790 Lighting Coil YB-06810 Valve Guide Remover
Test Lead Used with the Valve
It is used with a DVA Guide Remover
meter and the Peak YB-06801. It is used to
Voltage Adapter preset the valve guide
YU-39991 to measure depth in cylinder head.
voltage output.
Application: F200/225,
3 CYLINDER
2.8L, VF150A, VF175A,
2-STROKE
Application: F115
VFII5A, (L)F200A / (L)
YB-06795 Diagnostic Checking F225A / (L)F250
Lead
(Updated YB-06444) YB-06320 Valve Spring
Compressor Adapter
The diagnostic indicator
The adapter, when used
light flashes the ECU’s
with the Valve Spring
self-diagnostic code.
Compressor YM-01253,
compresses the valve for
Application: F115~ F225,
valve cotter removal or
3 CYLINDER
(L)F200A / (L)F225A /
4-STROKE
installation.
(L)F250
Use this attachment
YB-06766 Fuel Pressure Gauge with the Valve Spring
It is used for checking Compressor YB-04019 to
VST fuel pressure. depress the valve spring
retainer so the valve cot-
Application: F115~ F225 ters may be removed or
installed.
4&6 CYLINDER
Application: F200/225
YB-06869
2-STROKE
Test Lead, Pressure
Sensor Tester, VF200A, VF225A,
Oil Pressure VF250A, VF250XA,
Used with a DVA meter 2.8L, VF150A, VF175A,
to measure output volt- VFII5A, (L)F200A / (L)
age. F225A / (L)F250
VF250A, VF250XA,
and the Peak Voltage
4-STROKE
(L)F225,(L)250,(L)F300,
Adapter YU-39991, to
2.8L, VF150A, VF175A,
measure the output volt-
VFII5A, (L)F200A / (L)
age or the CDI unit.
F225A / (L)F250
Application: OX66,
HPDI, VF200A, VF225A, YU-03153M Marine Fuel Pressure
VF250A, VF250XA, Gauge Kit
(L)F225,(L)250,(L)F300, Use this fuel pressure
2.8L, VF150A, VF175A, gauge kit to attach
3 CYLINDER
drained of fuel.
VFII5A
2-STROKE
VF250A, VF250XA,
4-STROKE
800.727.6767
61 4&6 CYLINDER 4-STROKE 1-800-708-3184 | kLsupply.com
POWER HEAD TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YB-06682 Balance Hanger/ YB-06167 Bearing Cup Installer
Balance Hanger, This tool is used to
Cable&Hook Assy install oil seals for the
This tool was designed upper drive shaft oil
to provide balance while seal housing. also used
lifting and mounting to remove and install
1&2 CYLINDER
the VF200A,VF225A, the oil seal and prop
2-STROKE
VF250A,VF250XA 4.2L shaft bearing.
V6 outboard motors.
This tool should be Application:
mounted on the upper VF200A, VF225A,
engine block between VF250A, VF250XA,
the cylinder heads with (L)F225,(L)250,(L)F300,
2 6X1 bolts provided 2.8L, VF150A, VF175A,
with the tool. This tool VF115A
should be used with
1&2 CYLINDER
an appropriate lifting YB-06168 Oil Seal Installer
4-STROKE
harness such as the This tool is used to
YB-6AW01-A and lifting install seals into the oil
eye YB-06820. pump housing.
Application: Application:
VF200A, VF225A, 2.8L, VF150A, VF175A
VF250A, VF250XA, VFII5A
2.8L, VF150A, VF175A
YB-06615 Needle Bearing
Attachment
3 CYLINDER
This tool is used to
2-STROKE
YB-06804 Reamer, Valve Guide
5.53MM remove the crank shaft
It is designed to clean collar. as a pressing tool
out combustion deposits for a gear puller.
from inside the valve
guide. Application:
VF200A, VF225A,
Application: VF250A,VF250XA,
VF200A, VF225A, 2.8L, VF150A, VF175A
VF250A,VF250XA, VFII5A
3 CYLINDER
4-STROKE
2.8L, VF150A, VF175A,
YB-06686 Flywheel Stopper B
VFII5A This tool is used to hold
the flywheel during
YB-06830 Oil Filter Wrench
removal and installation
72.5MM
procedures.
This wrench fits on 69J
oil filters for removal
Application:
and installation.
2.8L, VF150A, VF175A
VFII5A
4&6 CYLINDER
Application:
2-STROKE
VF200A, VF225A,
YB-06847 Test Harness 3 PIN
VF250A, VF250XA, This test harness is used
(L)F225,(L)250,(L)F300, to measure lighting coil
2.8L, VF150A, VF175A output peak voltage
YB-06684 Pistion Ring Slider between all combina-
96MM tions of connectors.
Allows you to compress
the rings while install- Application:
ing piston. VFII5A
4&6 CYLINDER
YB-06846
4-STROKE
5GH FILTERS.
4-STROKE
pressing attachment.
Application:
VF200A, VF225A, Application:
VF250A, VF250XA, VF200A, VF225A,
(L)F225,(L)250,(L)F300, VF250A,VF250XA,
2.8L, VF150A, VF175A, 2.8L, VF150A, VF175A,
VF115A, (L)F200A / (L) VFII5A
F225A / (L)F250
YB-06681 Shift Rod Socket
YB-06155 Needle Bearing It shifts the lower unit
1&2 CYLINDER
Attachment
This tool is used to reverse when the lower
install new seals in unit has been removed
the oil pump housing. from the engine.
Also used to drive out
the lower drive shaft Application:
bearing. Use it with VF200A, VF225A,
YB-34474. VF250A, VF250XA,
(L)F225,(L)250,(L)F300,
Application: 2.8L, VF150A, VF175A,
3 CYLINDER
2-STROKE
(L)F225,(L)250,(L)F300,
VF200A, VF225A,
2.8L, VF150A, VF175A,
VF250A,VF250XA,
VFII5A
2.8L, VF150A, VF175A,
VFII5A
800.727.6767
63 4&6 CYLINDER 4-STROKE 1-800-708-3184 | kLsupply.com
LOWER UNIT TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YB-06502 Bearing Housing YB-06611 Needle Bearing
Puller Claw Attachment
This tool is used for- This tool is used to
removing the bearing remove the prop shaft
carrier. Also required bearing and seals from
for checking backlash on the bearing carrier hous-
1&2 CYLINDER
the forward and reverse ing. Also used for instal-
2-STROKE
gears lation of the drive shaft
bushing.
Application: Application:
VF200A, VF225A, VF200A, VF225A,
VF250A,VF250XA, VF250A,VF250XA,
2.8L, VF150A, VF175A, VF115A
VFII5A
YB-06661 Bearing Inner Race
YB-06504 Center Bolt Attachment
This tool is used as This tool is used to
1&2 CYLINDER
a forcing bolt with install the bearing onto
4-STROKE
YB-06501,YB-06502. the recerse gear.
Application:
Application: VF200A, VF225A,
VF200A, VF225A, VF250A, VF250XA,
VF250A,VF250XA, (L)F225,(L)250,(L)F300
2.8L, VF150A, VF175A,
VFII5A YB-06605 Driver Rod LL
This tool is used to drive
YB-06207 Bearing Housing bearing and seal remov-
3 CYLINDER
Puller ers.
2-STROKE
When used with a uni- Application:
versal puller (such as VF200A, VF225A,
YB-06117), these hooks VF250A,VF250XA,
will properly remove 2.8L, VF150A, VF175A,
the bearing carrier hous- VF115A
ing and propeller shaft.
Includes: YB-06207- YB-06623 Bearing Outer Race
Attachment
1 Hook Assembly,
This tool is used to
YB-06207-2 Hook
install outer bearing race
3 CYLINDER
Assembly, Heavy Duty
4-STROKE
into the bearing carrier.
Washers (2), and M8 x
Application:
1.25 Hex Nuts (2).
VF200A, VF225A,
VF250A,VF250XA
Application:
VF200A, VF225A, YB-06655 Forward Gear Needle
VF250A, VF250XA, Bearing Installer
(L)F225,(L)250,(L)F300, It installs the forward
2.8L, VF150A, VF175A, gear needle bearings.
VF115A, (L)F200A / (L) It is designed to install
4&6 CYLINDER
F225A / (L)F250 both needle bearings
2-STROKE
to their proper depth.
YB-06634 Ball Bearing
Use with Driver Handle
Attachment
YB-06071.
This tool is used to
Application:
remove the prop shaft
VF200A, VF225A,
bearing and seals from
VF250A, VF250XA,
the bearing carrier.
(L)F225,(L)250,(L)F300
Application:
YB-06610
4&6 CYLINDER
VF200A, VF225A, Needle Bearing
4-STROKE
VF250A,VF250XA Attachment
This tool is used to
install a new needle
YB-06715 Pinion Nut Holder B bearing into the
This tool is used for Propeller Shaft Bearing
removal and installation Housing at the specified
of the pinion nut. installation depth. Also
removal of drive shaft
Application: bearing from upper
VF200A, VF225A, drive shaft bearing
8 CYLINDER
4-STROKE
VF200A, VF225A,
Application: VF250A,VF250XA,
VF200A, VF225A, VF115A
VF250A,VF250XA,
2.8L, VF150A, VF175A YB-06641 Bearing Inner
Race Attachment
YB-06653 Needle Bearing This tool is used to
Attachment install the tapered roller
Used to install the prop bearing inner race to the
shaft needle bearing It drive shaft assembly.
1&2 CYLINDER
YB-06674
4-STROKE
Driveshaft Ring
YW-06628 Bearing Outer Race
Nut Wrench Attachment
Used for removal of the This tool is for installa-
drive shaft ring nut. tion of a new oil seal in
the oil seal housing at
Application: the specified installation
VF200A, VF225A, depth. Use with driver
VF250A, VF250XA, handle YB-06071.
(LF225,(L)250,(L)F300,
2.8L, VF150A, VF175A Application:
8 CYLINDER
4-STROKE
VF200A, VF225A,
VF250A,VF250XA,
2.8L, VF150A, VF175A,
VF115A
800.727.6767
65 4&6 CYLINDER 4-STROKE 1-800-708-3184 | kLsupply.com
LOWER UNIT TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
1&2 CYLINDER
which will accept a to properly install the
2-STROKE
Magnetic Dial Indicator driveshaft lower bear-
Base YU-34481. ing.
1&2 CYLINDER
4.2L
This tool is used to pinion gear nut. (90890-
4-STROKE
assist the technician in 06519)
selecting the proper pin-
ion shim. Application:
F75~ F/L115, VF115A
Application:
VF200A, VF225A,
VF250A,VF250XA
YB-06676 Pinion Shim Rod 4.2L YB-06200 Reverse/Forward Gear
This tool helps to prop-
3 CYLINDER
Bearing Installer
2-STROKE
erly insert the pinion It is used to install ball
shimming gauge into bearing onto reverse
the lower unit. gear. Use it with Driver
Handle YB-06071.
Application:
VF200A, VF225A, Application: F115, 2.8L,
VF250A,VF250XA VF150A, VF175A, (L)
F200A / (L)F225A / (L)
F250
YB-06614 Needle Bearing
3 CYLINDER
4-STROKE
Attachment YB-06213 Driveshaft Bearing
This tool is for install- Depth Plate
ing the new water seal, Use it with Driver
o-ring and cartridge into Handle YB-06071
the water pump hous- and Bearing/Oil Seal
ing. Attachment YB-06194 to
properly install lower
Application: driveshaft bearing.
VF200A, VF225A,
4&6 CYLINDER
VF250A,VF250XA Application: F115,
2-STROKE
VF115A, (L)F200A / (L)
YB-06642 Bearing Inner Race F225A / (L)F250
Attachment
Pressing tool used to
saperate the bearing YB-34468-2 Reverse Gear
from the gear. Shim Tool
It is used to properly
Application: measure the reverse
VF200A, VF225A, gear for shim height. 4&6 CYLINDER
VF250A,VF250XA,
Application: F115
4-STROKE
VF115A
YB-06680 Needle Bearing
Attachment
This tool was desgined YB-06199-A Forward Gear Outer
to remove and install Race Installer
the or lower drive shaft Use it with Driver
needle bearing. Handle YB-06071 to
properly install
Application: forward gear shim and
8 CYLINDER
VF250A,VF250XA
Application: F115
Handle YB-06071 to
install the forward gear
shims and outer bearing
race.
YB-34447 Gland Nut Wrench
This tool is used to
Application: F40-4 ~ F50
remove and install the
retainer nut that holds
in the propeller shaft YB-06270-A Forward Taper Roller
bearing housing.
3 CYLINDER
Bearing Installer
2-STROKE
(L)F250
2-STROKE
YB-06110 Driveshaft
Bearing Installer
It removes the lower
driveshaft needle bear-
YB-06071 Propeller Shaft Oil
Seal Installer ing. Use it with Driver
Use it with Driver Handle YB-06071 and
Handle YB-06071 to Depth Plate YB-06213.
install the propeller
4&6 CYLINDER
seals.
VF175A
Application: F40-4 ~ F50 YB-06153 Propshaft Needle
Bearing Attachment
This tool is used to
YB-06016 Bearing Installer/Oil install a needle bearing
Seal Installer into the drive shaft bear-
This tool was designed ing housing.
to install Oil Seals into
Application: T50~
8 CYLINDER
800.727.6767
67 4&6 CYLINDER 4-STROKE 1-800-708-3184 | kLsupply.com
LOWER UNIT TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
1&2 CYLINDER
bearing. race.
2-STROKE
Application: T50 Application: T60~ F100
YB-06112 Bearing Housing
YB-06269 Propeller Shaft Oil Remover
Seal Installer Use it with Driver
Use it with Driver Handle YB-06071 to
Handle YB-06071 to install the forward gear
install the propeller inner bushing.
shaft bearing housing
1&2 CYLINDER
prop shaft seals. Application: T60,
4-STROKE
VF200A, VF225A,
Application: T50~ F100 VF250A, VF250XA,
(L)F225,(L)250,(L)F300
YB-06276 Forward Gear
Bearing Installer YB-06200 Forward Gear
Use it with Driver Needle Bearing
Handle YB-06071 to It is used to properly
install forward gear install the forward gear
shims and outer bearing tapered needle bear-
ing. Use it with Driver
3 CYLINDER
race.
2-STROKE
Handle YB-06071.
Application: T50
Application: T60, 2.8L,
VF150A, VF175A
YB-06155 Driveshaft
YB-06244 Driveshaft
Bearing Installer Seal Installer
Use it with Driver Use it with Driver
Handle YB-06071 and Handle YB-06071 to
Depth Plate YB-34473 to install upper driveshaft
3 CYLINDER
properly set the lower
4-STROKE
seals.
driveshaft bearing.
Application: T60
Application: T50,
VF200A, VF225A, YB-06049 Driveshaft Holder
VF250A, VF250XA It is used to hold the
(L)F225, (L)F250, (L) driveshaft while
F300, 2.8L, VF150A, removing or installing
VF175A, (L)F200A / (L) the pinion gear nut.
F225A / (L)F250
4&6 CYLINDER
Application:
2-STROKE
F/T50 2001 ~ up
YB-06689 Valve Spring
YB-06156 Driveshaft Outer
Compressor
Race Installer
This special service tool
Use it with Driver
is used to compress
Handle YB-06071 to
the valve spring so the
install the upper drive
valve keepers can be
shaft shims and outer
removed.
bearing race.
4&6 CYLINDER
4-STROKE
Application: VF115A
Application: T50~ F100
Application: T60
properly set the lower
driveshaft bearing.
Attachment
hub. Use it with Driver
4-STROKE
Application: Application:
2.8L, VF150A, VF175A 2.8L, VF150A, VF175A
YB-06201
4&6 CYLINDER
Driveshaft Holder-
2-STROKE
Application:
2.8L, VF150A, VF175A Application:
2.8L, VF150A, VF175A
VFII5A
800.727.6767
69 4&6 CYLINDER 4-STROKE 1-800-708-3184 | kLsupply.com
LOWER UNIT TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YB-06619 Bearing Outer Race YB-06670 Pinion Height Gauge
Attachment New procedures have
It installs the forward been developed for
gear bearing outer shimming the VF115A
race. Use it with Driver lower unit. Refer to ser-
Handle YB-06071. vice manual lit-18616-
1&2 CYLINDER
03-60 for detailed proce-
2-STROKE
Application: dural information.
2.8L, VF150A, VF175A
Application:
YB-06258 Forward Bearing Race VFII5A
Installer
YB-06620 Bearing Outer Race
It installs the forward Attachment
gear bearing outer Used for installing the
race. Use it with Driver forward gear bearing
Handle YB-06071. outer race into the lower
1&2 CYLINDER
case that holds the for-
4-STROKE
Application: ward gear assembly.
2.8L, VF150A, VF175A Use with Driver Handle
Large YB-06071.
YB-06671 Pinion Height Gauge
Application:
New procedures have
VFII5A
been developed for
shimming the VF150A & YB-06609 Needle Bearing
VF175A lower unit. Attachment
It properly installs
3 CYLINDER
2-STROKE
Application: the driveshaft needle
2.8L, VF150A, VF175A bearing at the proper
depth into the hous-
ing bore. Use it with
Bearing Driver YB-06194
YB-06773 Up Relief Fitting and Driver Handle
This tool was designed YB-06071.
to attach to YB-06800 to
check pressure in the Application:
power tilt and trim sys-
3 CYLINDER
VFII5A
4-STROKE
tem. It can be used with
YB-06800 or YB-06776 YB-06085 Forward Gear Race
Installer
Application: Use this special tool to
2.8L, VF150A, VF175A drive in the reverse gear
VF200A, VF225A, bearing. Also used to
VF250A, VF250XA install the reverse gear
assembly. Use this spe-
YB-06607 Needle Bearing cial tool to drive on the
4&6 CYLINDER
Attachment forward gear bearing.
2-STROKE
Install the new needle
bearing into the forward Application:
gear to the specified VFII5A, (L)F200A / (L)
depth. Also used to F225A / (L)F250
install oil pump seals.
YB-06613 Needle Bearing
Also used as a pressing Attachment
tool. This special sercice tool
is used to install the
Application: bushing and dampers
4&6 CYLINDER
2.8L, VF150A, VF175A into SDS type propeller.
4-STROKE
Application:
VFII5A
ler shaft.
2-STROKE
4-Stroke Outboards
lower unit. YB-06376 Reverse Gear Bearing
Remover/Installer
Application: Use it with Driver
(L)F200A / (L)F225A / Handle YB-06071 to
(L)F250 remove/install the
reverse gear bearing
from the retainer.
YB-06578 Gland Nut Wrench
3 CYLINDER
Installer
4-STROKE
800.727.6767
71 4&6 CYLINDER 4-STROKE 1-800-708-3184 | kLsupply.com
PTT/MIDSECTION TOOLS
PTT/MIDSECTION TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YB-06520 Driveshaft Holder YB-06175-2B Trim Cylinder Wrench
It is used to hold the Used to remove most
driveshaft while remov- PTT cylinder end caps.
ing or installing the
pinion gear nut. Application:
F40-4 ~ F/L115,
1&2 CYLINDER
Application: F200/225 VF200A, VF225A,
2-STROKE
VF200A, VF225A, VF250A, VF250XA,
VF250A, VF250XA, (L)F225,(L)250,(L)F300,
(L)F225,(L)250,(L)F300 (L)F200A / (L)F225A
/ (L)F250,F75 ~ F100 5,
VF115A
YB-06048 Gland Nut Wrench
It removes and installs YB-06569 Tilt Rod Wrench
the lower gland nut. It Use it with the PTT
is designed specifically Piston Vise Tool
1&2 CYLINDER
for Yamaha motors. It is YB-06572 to the remove
4-STROKE
manufactured from high top pin eyelet. Enables
strength alloy steel and end cap servicability.
heat-treated for strength
and durability. Application: F200/225,
VF200A, VF225A,
Application: Counter VF250A, VF250XA,
Rotation F200/225 (L)F225,(L)250,(L)F300,
VF115A, (L)F200A / (L)
F225A / (L)F250
3 CYLINDER
YB-06194 Driveshaft Needle
2-STROKE
Bearing Installer
and Remover YB-06572 PTT Piston Vise Tool
It removes and installs Use it with Tilt Rod
the driveshaft needle Wrench YB-06569 to
bearing. Use it with remove the top pin
Driver Handle YB-06071 eyelet. It enables tilt
and Depth Plate cylinder end cap servi-
YB-06213. cability.
3 CYLINDER
Application: Application: F200/225,
4-STROKE
FL/115 ~ F225, 2.8L, VF200A, VF225A,
VF150A, VF175A, VF250A, VF250XA,
VF115A (L)F225,(L)250,(L)F300,
VF115A, (L)F200A / (L)
YB-06195-A Oil Seal Installer F225A / (L)F250
It installs both oil seals
properly into the reverse YB-06548 TNT Wrench,
gear bearing hous- Showa System
Used to remove or
4&6 CYLINDER
ing. Use it with Driver
install the PTT cylinder
2-STROKE
Handle YB-06071.
end caps. cylinders from
Application: Showa 1997 and up.
FL/115 ~ F225, (L)
F200A / (L)F225A / (L) Application: F40 ~
F250 F115, VF200A, VF225A,
VF250A, VF250XA, 2.8L,
VF150A, VF175A
4&6 CYLINDER
YB-06776 PTT Pressure Gauge
4-STROKE
Application: F200/225
4-STROKE
VF150A, VF175A
YB-06800 or YB-06776.
2-STROKE
Application:
Application: VF200A, VF225A,
VF200A, VF225A, VF250A, VF250XA,
VF250A, VF250XA, 2.8L, (L)F225,(L)250,(L)F300,
VF150A, VF175A (L)F200A / (L)F225A /
(L)F250
YB-06800 Hydraulic Pressure
Gauge
This tool was designed
1&2 CYLINDER
VF250A, VF250XA
F225A / (L)F250
Bearing Installer
2-STROKE
It is used to install
forward gear bearing.
YB-06175-1A Trim Wrench
Also use Driver Handle
This wrench was
YB-06229. Also used for
designed to remove and
installing the drive shaft
install trim caps that
bushuing into the mid
have a 32MM drill circle
section.
and four 4MM holes
within the 32MM drill
Application:
circle.
4&6 CYLINDER
VF200A, VF225A,
4-STROKE
VF250A, VF250XA,
Application:
(L)F225,(L)250,(L)F300
VF200A, VF225A,
VF250A, VF250XA, 2.8L,
VF150A, VF175A
8 CYLINDER
4-STROKE
800.727.6767
73 4&6 CYLINDER 4-STROKE 1-800-708-3184 | kLsupply.com
8 CYLINDER
4-STROKE
POWER HEAD TOOLS
POWER HEAD TOOLS
SHOP TOOLS &
EQUIPMENT
GENERAL
smoothing (shows an
averaged reading of
measurements which
fluctuate such as rpm).
YM-34487 Spark Checker
minimum / maximum Oppama Pet-4000
/ average recording of Pulse Ignition Spark
measurements, leads, Checker
test probes, large The PET -4000 Pulse
alligator clips, users Ignition Spark Checker
4&6 CYLINDER
Application:
4-STROKE
manual).
V8 5.3L OFFSHORE Application:
MODEL 2007 V8 5.3L OFFSHORE
THROUGH 2016 MODEL 2007
THROUGH 2016
800.727.6767
75 8 CYLINDER 4-STROKE 1-800-708-3184 | kLsupply.com
POWER HEAD TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
1&2 CYLINDER
YU-39991 to measure
2-STROKE
voltage output. Application:
5.3L F300 & F350
Application:
5.3L F300 & F350
1&2 CYLINDER
fuel pump and injector
to provide balance while
4-STROKE
rail when used with
fuel pressure gauge lifting and mounting
YU-03153M the F300 & F350 5.3L V8
outboard motors. This
Application: tool should be mounted
5.3L F300 & F350 on the upper engine
block between the
cylinder heads with
YU-03153-M Marine Fuel Pressure 2 6X1 bolts provided
Gauge Kit with the tool. This tool
3 CYLINDER
Use this fuel pressure
2-STROKE
should be used with
gauge kit to attach an appropriate lifting
directly to the vapor harness such as the
separator tank, or attach YB-6AW01-A
between the fuel pump
and injector rail when Application:
used with the YB-06946 5.3L F300 & F350
fuel pressure gauge
adapter. Attach this new
tool to the fuel system
3 CYLINDER
and obtain an accurate
4-STROKE
fuel pressure reading.
When you are finished
place the small clear fuel
pressure relief hose into YB-06139 Flywheel Holder
the fuel tank or This tool holds the fly-
appropiate container wheel magneto for tight-
and push the fuel ening and loosening of
release button. the flywheel nut.
4&6 CYLINDER
Application:
2-STROKE
Application:
5.3L F300 & F350 V8 5.3L OFFSHORE
MODEL 2007
THROUGH 2016
YU-33223
4&6 CYLINDER
Compression
4-STROKE
Gauge Set
Includes 12” hose,
spark plug hole adapter
pressure gauge and air
release quick coupler.
It works on all Yamaha
2-stroke & 4 stroke out-
board motors.
Application:
8 CYLINDER
4-STROKE
V8 5.3L OFFSHORE
MODEL 2007
THROUGH 2016
Application: Application:
5.3L F300 & F350 5.3L F300 & F35
Compressor
2-STROKE
Application:
Application:
5.3L F300 & F350
5.3L F300 & F350
4&6 CYLINDER
4-STROKE
Application:
V8 5.3L OFFSHORE
MODEL 2007
THROUGH 2016
800.727.6767
77 8 CYLINDER 4-STROKE 1-800-708-3184 | kLsupply.com
POWER HEAD TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YM-A8998 Valve Lapping Tool YB-06071 Driver Handle Large
The Valve Lapping This heavy-duty handle
Tool is the ultimate is used with the
vacuum stick for insur- appropriate adapters to
ing perfect surfaces on remove and install seals
valves and valve seats. and bearings.
1&2 CYLINDER
Interchangeable cups
2-STROKE
make the unit suitable Application:
for use with virtually V8 5.3L OFFSHORE
any size valve. The set MODEL 2007
includes vacuum stick THROUGH 2016
and 3/4” and 1/4”
diameter rubber cups.
Application:
V8 5.3L OFFSHORE
LOWER UNIT TOOLS
1&2 CYLINDER
MODEL 2007
4-STROKE
THROUGH 2016
Part Description / Use
YB-06791 Pulser Coil Test Number
Harness 3 Pins
It is used with a DVA YB-06052 Shift Rod Push Arm
It shifts the lower unit
meter and the Peak
into forward, neutral or
Voltage Adapter
reverse when the lower
YU-39991 to measure
unit has been removed
voltage output.
from the engine.
3 CYLINDER
2-STROKE
Application:
5.3L F300 & F350
Application:
5.3L F300 & F350
3 CYLINDER
oil when replacing the
4-STROKE
reverse when the lower
oil filter.
unit has been removed
from the engine.
Application:
5.3L F300 & F35
Application:
V8 5.3L OFFSHORE
MODEL 2007
THROUGH 2016
4&6 CYLINDER
YB-35956-B
2-STROKE
Lower Unit Pressure
YB-69000 Oil Filler Cap Installer/
/ Vaccum Tester
Remover Tool
The hand pump device
This tool was designed
provides both pressure
to easily remove and
and vacuum for leak
install the oil filler cap
testing of the lower unit.
on Yamaha 4 stroke out-
board motors without
Application:
damage to the cap.
V8 5.3L OFFSHORE 4&6 CYLINDER
MODEL 2007
Application: All
4-STROKE
THROUGH 2016
MODELS
Application: ALL
MODELS
Application:
2-STROKE
V8 5.3L OFFSHORE
MODEL 2007 Application:
THROUGH 2016 5.3L F300 & F350
Application:
4-STROKE
Application:
shims and outer bear-
2-STROKE
Application:
5.3L F300 & F350 YB-06823 Ring Nut Wrench #2
This tool is used with
4&6 CYLINDER
with YB-06784 to
4-STROKE
Application:
5.3L F300 & F350
800.727.6767
79 8 CYLINDER 4-STROKE 1-800-708-3184 | kLsupply.com
LOWER UNIT TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
1&2 CYLINDER
Application:
2-STROKE
Application: 5.3L F300 & F350
5.3L F300 & F350
1&2 CYLINDER
Attachment
This tool is to be used
4-STROKE
Application: with 90890-06605 driver
5.3L F300 & F350 tool for needle bearing
attachment.
Application:
3 CYLINDER
2-STROKE
5.3L F300 & F350
YB-06664 Needle Bearing
Attachment #1
This tool is used to
attach the driveshaft
YB-06715 Pinion Nut Holder B needle bearing.
This tool is used for
removal and installation Application:
of the pinion nut. 5.3L F300 & F350
3 CYLINDER
4-STROKE
Application:
5.3L F300 & F350
4&6 CYLINDER
Holder Pinion nut Tool. then place the forward
2-STROKE
During pinion nut gear complete into the
removal and installa- outer race.
tion.
Application:
5.3L F300 & F350
Application:
5.3L F300 & F350
4&6 CYLINDER
4-STROKE
Application:
5.3L F300 & F350
1&2 CYLINDER
Application:
YB-06085 Oil Seal Installer 5.3L F300 & F350
It is used to install
shims and outer bear-
ing race for the forward
gear. It also requires the
use of Driver Handle
8 CYLINDER
4-STROKE
YB-06071.
Application:
5.3L F300 & F350
800.727.6767
81 8 CYLINDER 4-STROKE 1-800-708-3184 | kLsupply.com
pTT/midsection tools
PTT/MIDSECTION TOOLS
GENERAL
Part Description / Use Part Description / Use
Number Number
YB-06117 Universal Puller YB-06838 Up Relief Fitting T&T
Heavy duty puller for Pres Test
removing flywheels, This tool is used to
balancers and propeller determine oil press-
shaft bearing housings. sure in the ptt up relief
system. The YB-06838
1&2 CYLINDER
Application: attaches to the YB-06800
2-STROKE
V8 5.3L OFFSHORE oil pressure gauge.
MODEL
2007 THROUGH 2016 Application:
V8 5.3L OFFSHORE
MODEL
2007 THROUGH 2016
1&2 CYLINDER
4-STROKE
YU-03097 Dial Indicator (0-5MM) YB-06800 Hydraulic PTT
This is used for backlash Pressure Gauge
adjustment during This tool is used to
shimming processs. determine oil presssure
in the ptt relief systems.
Application: The YB-06774 and the
3 CYLINDER
All YB-06838 attach to
2-STROKE
the YB-06800 Pressure
Gauge
Application:
V8 5.3L OFFSHORE
MODEL
2007 THROUGH 2016
3 CYLINDER
4-STROKE
Plate
This universal plate
bolts to the lower unit
and will accept most
magnetic dial indicator
YB-06774 Drive Shaft Holder
bases for accurate lower This tool is used to
unit backlash checks. determine oil presssure
in the ptt down relief
Application: system. The YB-06774
4&6 CYLINDER
V8 5.3L OFFSHORE attaches to the YB-06800
2-STROKE
MODEL oil pressure gauge.
2007 THROUGH 2016
Application:
YU-A8438 Magnetic Base V8 5.3L OFFSHORE
Stand Only MODEL
This magnetic base 2007 THROUGH 2016
stand can be used in
place of YU-34481 flex-
ible magnetic dial indi-
4&6 CYLINDER
MODEL Application:
2007 THROUGH 2016 V8 5.3L OFFSHORE
MODEL
2007 THROUGH 2016
800.727.6767
83 MARINE CATALOG 1-800-708-3184 | kLsupply.com
POLICES & PROCEDURES