Professional Documents
Culture Documents
Driving Shafts: Straight
Driving Shafts: Straight
Driving Shafts: Straight
Straight
QFeatures: Rotary Shafts suitable for driving motion. Accuracies and shapes needed for rotary driving applications are selectable.
QSelection of Driving Shaft
Type D Tolerance MMaterial HHardness SSurface Treatment Tolerance Circularity M
D
h7 h6
D Not Hardened
Hardened In selecting a driving shaft, select the basic shape and size from the specification table, then select necessary alterations such as thread machining, keyway addition etc.
KZAN - 10 0
- 0.015
0
- 0.009 10 <Selection Example of Part Number>
0.004 • Alteration Selection: Two Keyways
KZAC h7 S45C - Black Oxide 12 12
15 0 0 15 0.003
KZAP Electroless Nickel Plating - 0.018 - 0.011
17 17 0.005
Ø40
Induction Hardened 20 20
KZAF h6 S45C - 0 0
Surface Hardness 50HRC~ 25 25 Keyless Timing Pulley
- 0.021 - 0.013
30 30
0.006 50 100 <App. Example> Bearing with Housing
35 35
0.005 175 100
40 0 0 40
45 - 0.025 - 0.016 45
0.007 450
50 50
G EThe example below shows the keyway shape under the following
G M
G 6.3 1.6 1.6 conditions: When KA, KB, KC, KD, ZA, ZB, ZC, ZD=0 When KA+HA,
2-C0.5 KB+HB, KC+HC, KD+HD, ZA+HA, ZB+HB, ZC+HC or ZD+HD = L
1.6 1.6 G
1.6 1.6 Roller - Straight with Keyway
*For KZAF, will be
*KZAF may have centering holes on
D
shaft ends.
L±0.2
F11-15_d03
Part Number - L - (MA, NA, KA, TA, SC, WA•••etc.)
KZAF40 - 450 - KA50 - HA100 - KB175 - HB100
EPlease note that D dimension tolerance of KZAF is different from that of KZAN, KZAC and KZAP.
Type KZAN KZAC KZAP Keyway Adds a keyway. Specify the position and the length of the keyway.
Min. L L100.5 L200.5 L300.5 L400.5 Min. L L100.5 L200.5 L300.5 L400.5 Min. L L100.5 L200.5 L300.5 L400.5 Ordering Code KA10-HA30-KB100-HB50
D ~100.0 ~200.0 ~300.0 ~400.0 ~500.0 ~100.0 ~200.0 ~300.0 ~400.0 ~500.0 ~100.0 ~200.0 ~300.0 ~400.0 ~500.0 KA KA, HA, KB, HB, KC, HC, KD, HD = 1mm Increment
KB E3≤HA,HB,HC,HD≤100
10 - - - - - - KA HA EKeyway Details P.820
12 - - - - - - KB HB
KC EWhen more than 2 keyways are added, the tolerances may shift by up to 0.2°.
15 - - - KC HC KD
17 - - - KD HD
20 - - -
Keyway Machining + Set Screw Flat Adds a flat at any designated angle based on the keyways. Specify the position and the length for each keyway, and the angle for the set screw flats.
25
Ordering Code ZA40-HA20-AA90
30
ZA ZA, HA, ZB, HB, ZC, HC, ZD, HD= 1mm Increment AA, AB, AC, AD= 30° Increment 30°≤ AA, AB, AC, AD ≤330°
H
0˚ E3≤HA,HB,HC,HD≤100 EKeyway Details P.820
onfi
gura
ble
ZB Angle Specified D 10~17 18~40 45, 50
Type KZAF Ang
le C
ZA HA ZC
• Ordering Code Keyway
Position Specified
Keyway
Width Specified 30° Increment H 1 2 3
Min. L L100.5 L200.5 L300.5 L400.5 ZB HB ZA HA AA
D ZD ZB HB AB
EThe length of each set screw flat is the same as that of each
keyway.
~100.0 ~200.0 ~300.0 ~400.0 ~500.0 ZC HC
ZC HC AC EFor a keyway and the angle of a set screw flat, the
10 - - ZD HD ZD HD AD tolerances may shift by up to ±0.2°.
12 - - W
Wrench Flats Adds a wrench flat. Specify the position of a wrench flat.
15 - Ordering Code SC180 SC = 1mm Increment 0≤SC≤L-L
17 -
20 - SC D 10 12 15 17 20 25 30 35 40 45 50
W 8 10 13 14 17 22 27 30 36 38 41
25 L 8 10 15 20
30 SC l
35 2 Set Screw Flats (Angle Specified) Adds a flat at any designated angle besides the datum plane 0°.
40 Specify the position, the length and the angle of the set screw flats. When 0° is specified, only one set screw flat is
H machinable.
45 - Ordering Code WA15-GA10-AA0
50 - WA WA, WB, WC, GA, GB, GC= 1mm Increment AA, AB, AC = 30° Increment 0°≤ AA, AB, AC ≤330°
H
0°
rable
WB
figu
Ang
le C
on WA GA WC Set Screw Flat
Position Specified
Set Screw Flat
Width Specified
Angle Specified
30° Increment
D
H
10~17
1
18~40
2
45, 50
3
• Ordering Code
WB GB WA GA AA
WC GC WB GB AB
WC GC AC
1 -869 1 -870