Professional Documents
Culture Documents
How To Use The Machine2
How To Use The Machine2
Add the type 46 Hydraulic Oil and connect the 380v,triple phase,50Hz electricity;
2. Rotate the red button and wait for the computer on;
3. Click the “MONITOR”,“MANUAL” and “MOTOR ON/OFF” Button let the machine
goes in data setting mode;
5. Click the “MOLD OPEN” Button to let the upper plate goes up so the mold could
be inserted into the machine;
6. Insert the mold into the middle of the machine plate and align the hole in the
mold with the hole in the machine's nozzle;
7. Click the “NOZZ.ADV” button intermittently to let the nozzle goes down and click
the “MOLD CLOSE” button to let the nozzle hole close to the mold hole,but
don’t let the nozzle touch the mold;
8. After confirming the nozzle hole align the mold hole,click the “NOZZLE RET.”
Button to let the nozzle goes up;(Noted:when you align the mold
position,please turn off the MOTOR.)
9. Click the “MOLD CLOSE” Button to let the upper plate press the mold;
10. Confirm the nozzle hole is on top of the hole of mold; Click the “NOZZLE ADV.”
Button to let the nozzle hole touch the mold hole;
When the mold close,click the “M.PLT” button to set up the data of mold opening
and closing.
You could set up the press data(black frame) as the photo shown,and you need to
set up the data of your mold in place data(red frame)
For example,the data is “20.4”mm in the photo,you need to set up the “22.0” in
the “LOWP(Place)”.2 mm more than the data in the green frame.And the
“CLOF(Place)” need to be 40-50mm more than the data
of“LOWP(Place)”.” HighP” data is “1s”-“1.5s”.All molds are the
same.
The “O.LOW(Place)” means the mold opening stroke you want.You could set
the data the same as the photo.The “Unloa”is 0.20s,all molds are the same.
Set the data of “INJECTION”
When the machine finishes plastic injection and the plastic go little outside
from the mold or the cable is pressed much,you decrease the data of
“Inj1(Pres)”and “Inj2(Pres)”until the plastic don’t go out.Suggest
decrease 5 per time.The data bigger,the pressure bigger.
When the plastic is not enough for one full shot,please come to the
“FEEDING” page setting
Set the data of “FEEDING”
Set up the data of “TEMP.”in the green frame the same as the photo.When
the data of “Meas”arrives the data of “Set”,it means the temperature is
enough to make a plastic injection.
Secondly,press the “NOZZLE RET.”to let the nozzle go up and click
“CHARGE”to let the screw barrel filled with the plastic.Then press the
“INJECTION”to inject the hard plastic out.This is used to make the screw
barrel filled with the melting plastic.After that take out the injection plastic and
press the “NOZZLE ADV.”to let the nozzle touch the mold.
Thirdly,change the machine mode into “SEMI AUTO”mode and make a
empty shot.You should use both your hands to press the green buttons
together.After the mold closes,you could hold your hands back.
Finally,if you feel the plastic is enough to make a full shot,you put the feeding
parts in the mold and make a injection.If you ensure it is ok to make a full shot
of final products,you put the semi products into the mold and make a shot.
If you want to stop production,you need to change the machine mode into
“MANUAL”and click the “NOZZLE RET.”button to let the nozzle go up
and press the “INJECTION” button to inject the plastic out.Then press the
red button to turn off the machine.