Professional Documents
Culture Documents
35P 3-Taiyo
35P 3-Taiyo
3.5 MPa Hydraulic Cylinder with 3.5 MPa Hydraulic Cylinder with
2 35P-3 Position Detector Position Detector 35P-3 3
pulse encoder
f32 f40 f50 f63 f80 f100
Main circuit
Main circuit
2.2kΩ 100Ω
Boots Standard : Nylon tarpaulin Semi-standard : Chloroprene, Conex Output circuit
Slipper Seal is the registered
Phase A & B
Accessory f40 25 25 diagram Phase A & B
Rod end attachment Rod eye (T-end), rod clevis (Y-end) with pin, floating joint (F-end) trade mark of Nippon Valqua
Industries, Ltd.
GND GND
f50
Conex is the registered 35 35
Metallic receptacle
f63
trademark of Teijin Limited.
Cushion Stroke Length Unit: mm f80 20 20 1 4 (+24V)
Wiring method 1 +12V 3 Phase A
f100 2 3 2 GND 4 Phase B
Cushion stroke
Cylinder bore
(cushion ring length)
f32 to f63 16 Adaptability of Fluid to Seal Material Piston rod advancing direction Piston rod retracting direction
360° 360°
f80 to f100 20 Applicable fluid H H
Seal
35P-3
35P-3
Phase A Phase A
The cushion stroke lengths in case of cylinders used up to material Petroleum- Water- Phosphate Water in Oil in
L L
the stroke end. based fluid glycol fluid ester fluid oil fluid water fluid
Output mode
Phase B
H
Phase B
H
the cushioning effect will be weakened. In such a case, Phase A advances Phase A delays
consult us. Note) ○ : Applicable × : Inapplicable 90°±45° from phase B. 90°±45° from phase B.
● How to order
General Purpose Type The item enclosed by broken line needs not to be entered, if unnecessary. Semi-standard
specification
Sensor List Semi-standard
l❼
t❾
Max. Protective
y
pe
yle
ts
Type Sensor symbol Load voltage range Load current range Indicating lamp Wiring method Cord length Applicable load
en
l
tit
bo
or
ok
ia
in
switching capacity circuit
hm
st
an
Ty
oo
er
m
rb
on
tr
sy
at
qu
ac
g
B
S
de
hi
in
att
1.5m
lm
AF AX101CE
or
or
nt
us
in
ns
ns
nd
a
None
ou
yl
Se
Se
Se
C
de
LED
C
M
AG AX105CE 5m
Ro
DC : 5 to 30V DC : 5 to 40mA (Lights in red 0.3mm², 2-core, outer dia.
Standard type 35P-3 1 LA 40 B 100 − C 0 − T − J AH AX111CE AC : 5 to 120V AC : 5 to 20mA
DC : 1.5W
1.5m
AC : 2VA Provided when sensing) f4mm Rear wiring
AJ AX115CE 5m
Switch Set 35P-3R 1 LA 40 B 100 − AH 2 − T − J
Reed sensor
DC : 30V or less DC : 40mA or less
AE AX125CE AC : 120V or less AC : 20mA or less None None 5m Small relay,
AK AX11ACE AC : 5 to 120V 5 to 20mA 2VA LED 0.5m programmable
Provided (Lights in red 4-pin connector type
AL AX11BCE DC : 5 to 30V 5 to 40mA 1.5W Rear wiring 0.5m controller
when sensing)
1 U seal (nitrile rubber) NJN Nylon tarpaulin LED
0.3mm², 2-core, outer dia.
8 Slipper Seal JN Chloroprene AM AX135CE AC/DC : 90 to 240V 5 to 300mA B contact output Provided (Lights in red
f4mm Rear wiring
5m
when not sensing)
JK Conex
Neon lamp
S SR405 AC : 80 to 220V 2 to 300mA 30VA Provided (Lights when 0.5mm², 2-core, outer 5m
not sensing) dia. f6mm Rear wiring
Mounting Style
35P-3
HH HH
3.5 MPa Hydraulic Cylinder with 3.5 MPa Hydraulic Cylinder with Position Detector
6 35P-3 Position Detector Unit: mm Double Acting Single Rod 35P-3 7
Port position Ⓐ, cushion valve position Ⓑ Change of detector specifications f63 7.28 0.29 0.46 0.51 1.15 0.40 0.22 0.35 0.41 0.0094
Detector specification supply voltage : 12 V DC (NPN open collector output) f80 11.54 0.66 0.86 1.23 2.27 1.02 0.76 1.01 1.41 0.0122
Output type : 12 V DC, With boots f100 17.03 0.96 1.60 1.47 3.26 1.28 1.30 1.76 2.68 0.0200
AB-phase Change of piston rod end
output (90°phase) Calculation formula : Cylinder weight (kg)=basic weight+mounting accessory weight+additional sensor
Plated cylinder tube
weight+additional weight per mm of stroke×cylinder stroke (mm)
(hard chrome plating thickness 0.02 mm)
Calculation example : Standard type, LB style, bore f63, cylinder stroke 200 mm 7.28+0.46+0.0094×200=9.62kg
Magnetic proximity sensor of SR type
Change of port and cushion valve positions
The standard port position is Ⓐ, and the standard cushion Sensor Additional Weight Unit: kg
valve position is Ⓑ. When modifying the positions, enter End Lock Nut Part Number
the symbol shown in the dimensional drawings. (On the Bore Number Sensor AX type SR type
standard models, the detector is installed on the top.) Bore (mm) Cord length 1.5 m Cord length 5 m With
connector Cord length 1.5 m
f32
(Example) LNA-12F-H f32
f40
35P-3R 1LA40B100− B C AH2−J
f40
f50
Port position (A, B, C, D) LNA-18F-H f50 0.05 0.13 0.04
Cushion valve position (A, B, C, D, or 0)
f63 0.22
f63
f80 LNA-24F-H
In case that the cushion is not equipped, the f80
cushion valve position is“0” . f100 LNA-30F-H
f100 0.07 0.14 0.06
○ ○ × ○ ○
Hydraulic Cylinders with Position Detector
35P-3
HH HH
3.5 MPa Hydraulic Cylinder with Position Detector 3.5 MPa Hydraulic Cylinder with Position Detector
8 35P-3 Position Indicator with Multi-point Output Position Indicator with Multi-point Output 35P-3 9
● How to order
s❶
d❷
s❶
❸
d❷
❸
position sensing cylinders
pe
pe
o
o
rie
rie
th
th
Ty
Ty
Se
me
me
Se
ut
ut
Inp
Inp
Environmentally-friendly lead-free indicator PQCPA − CU − A − A PQCPA − CU − P − 12
Analog input and pulse input types are available.
Provided with multi-point output function (5 points) as
a standard function to enable to individually set the A Current input 12 12V open collector input, 12V voltage input
upper and lower limits Note 1)
V Voltage input 24 24V open collector input, 24V voltage input
A 16-bit AD converter is provided to realize high
resolution. (Analog input type) 00 Differential input
Provided with a counter with a response frequency of Note) Cylinders do not come with indicators of 00
200 kHz (Pulse input type) differential input type. (Specification to use the
Provided with a pulse position correcting function Note 2) indicator in stand-alone state)
Note 1) Setting the bank switching enables to use the CN1 connector CN2 connector
multi-output function of up to 15 points. Display (fluorescent display tube) (for input of measuring (for output of measuring
Note 2) Position correction can be made by mounting a sensor signal) sensor signal)
cylinder sensor. Positional error caused by slippage
of the encoder is eliminated.
Standard Specifications
Type Analog Pulse
Model number PQCPA-CU-A PQCPA-CU-P
Applicable input signal Analog voltage/analog current Phase AB
Display ranges ±999999
Status indication lamp block (LED) Operation key block CN3 connector CN4 connector
Resolution Stroke×1/10000 — (for control input/output) (for power supply)
Response frequency 1kHz 200kHz Front face Rear face
Linearity ±0.02%FS —
← →
35P-3
35P-3
Bank switching Bank switching 35P-3
CN5 ↓ HOLD SET
Multi-point output Multi-point output 70P-8 Linear pulse encoder Encoder type
Functions
Positional data hold Positional data hold 140P-8 130 1.5 78.5
140
— 0 setting signal Note) For the details of each cylinder, see the section
Front view Side view
— Correcting function of each series.
HH HH
3.5 MPa Hydraulic Cylinder with Position Detector 3.5 MPa Hydraulic Cylinder with Position Detector
10 35P-3 Position Indicator with Multi-point Output Position Indicator with Multi-point Output 35P-3 11
● How to order
How to order cable between sensor and indicator External Input/Output
CN1 CN3
❸
s❶
r❷
th
de
rie
ng
Description Signals Pin No. Description Signals
lin
Pin No.
Se
cy
le
le
1 Voltage/current input Analog input 1 0 setting signal Input
e
ab
bl
lic
Ca
NC — 2 Positional data hold Input
p
2
Ap
Voltage/current GND Analog input 3 Correcting function Input
PQCPA − CV1 − 01
3
4 Phase A Pulse input 4 Bank switching 0 Input
5 −Phase A Pulse input 5 Bank switching 1 Input
CV1 PTH-1・PTN-1B・PTT-1B 01 1m 6 Phase B Pulse input 6 Bank switching 2 Input
CV2 35P-3・70P-8・140P-8 05 5m 7 −Phase B Pulse input 7 Reserved input Input
+24V Power supply output 8 Reserved input Input
CV3 PSR-1A 10 10m 8
9 +12V Power supply output 9 Input common Input
* When ordering a cable, confirm the series name of the actuator on the sensor side. 10 GND Power supply output/Phase AB GND 10 Input common Input
Some models cannot be connected. 11 Multi-point output signal 0 Output
* After wiring, connect the indicator side connector to the CN1 connector on the indicator. CN2 12 Multi-point output signal 1 Output
Pin No. Description Signals 13 Multi-point output signal 2 Output
PQCPA-CV1- Cable length 1 Pout Analog output 14 Multi-point output signal 3 Output
2 Vss Analog output 15 Multi-point output signal 4 Output
Applicable actuators:PTH-1B/PTN-1B/PTT-1B PQCPA-CU-* A pulse Pulse output 16 Reserved output Output
3
AWG24×2P PQC series control unit PQCPA
4 A pulse GND Pulse output 17 Reserved output Output
POWER ERROR HOLD
↑ MODE RST
5 B pulse Pulse output 18 Reserved output Output
← →
CN5 ↓ HOLD SET 6 B pulse GND Pulse output 19 Output common Output
Cable length (1m, 5m, 10m) 20 Output common Output
CN4 * For details, see the instruction manual.
PQCPA-CV2- Cable length Pin No. Description Signals
1 P24 Power supply
Applicable actuators:35P-3/70P-8/140P-8
PQCPA-CU-* 2 N24 Power supply
AWG24×4C PQC series control unit PQCPA 3 PE Power supply
← →
PQCPA-CV3- Cable length Actuator Cable between sensor and indicator Indicator I/O cable
PQCPA-CU-A-A
Applicable actuators:PSR-1A PQCPA-CU-A-V
2m PQCPA-CU-*
PTH-1B PQCPA-CV1-*
AWG24×2P PQC series control unit PQCPA
PTN-1B
Amplifier PTT-1B
CN1 CN2 CN4
↑
CN3
POWER ERROR HOLD
MODE RST
← →
CN5 ↓ HOLD SET
CN1 connector
PQCPA-IO
Hydraulic Cylinders with Position Detector
Note) PSR-1A comes with a 2-m cable as a standard accessory. If another cable is required, select
PQCPA-CU-P-12
this cable. (In this case, disconnect the standard cable (2m) of PSR-1A, and connect the selected
PQCPA-CU-P-24
cable directly to the amplifier.)
35P-3 PQCPA-CV2-*
How to order I/O cable
70P-8
CN1 CN2 CN4
140P-8 CN3
35P-3
← →
CN5 ↓ HOLD SET
CN1 CN2 CN4
CN3
Y0, 3-3
CN3 half-pitch connector CN1 connector
Note) Only the CN3 half-pitch connector is supplied as a standard accessory.
If you need the connector with a cable, place an order for the connector.
HH HH
3.5 MPa Hydraulic Cylinder with Position Detector 3.5 MPa Hydraulic Cylinder with Position Detector
12 35P-3 Double Acting Single Rod Unit: mm Unit: mm Double Acting Single Rod 35P-3 13
Dimensional Table
SD Symbol
35P-3 1 SD Bore B Stroke A B B1 BB CS D DD E EE FF
Bore
f 32 24 f 30f9 19 7 6 13 M6×1 □ 44 Rc1/4 15
f 40 24 f 30f9 19 7 6 13 M6×1 □ 50 Rc3/8 15
5 f 50 36 f 34f9 24 7 6 19 M6×1 □ 62 Rc3/8 15
f 63 36 f 34f9 24 9 8 19 M8×1.25 □ 76 Rc3/8 15
D
f 80 48 f 42f9 32 10 10 24 M10×1.25 □ 94 Rc1/2 20
B
f 100 60 f 50f9 41 12 12 30 M12×1.5 □ 114 Rc1/2 20
Symbol
FP GG H HF HK HM HP h J K
Bore
f 32 99 Rc1/8 30 103 22 19 81 7 38 25
WP ZJ+stroke f 40 99 Rc1/8 30 106 25 22 81 7 38 25
0.5□4-core
shielded cable 34 WR WS A W FP P+stroke f 50 99 Rc1/4 30 115 31 31 84 11 38 25
f 63 99 Rc1/4 33 122 38 38 84 11 38 25
2-EE 4-DD
24 f 80 107 Rc1/4 31 134 47 47 87 14 45 32
A h f 100 113 Rc1/4 31 155 57 57 98 17 45 32
HP
HF
D B Symbol
MM KK LF MM P RR W WP WR WS YK ZJ
HK HM Bore
KK
Width across flats f 32 M12×1.25 168 58 □ 33 15 80 55 25 60 183
C B1 of lock nut for rod Cushion valves f16
RR end attachment YK J H+stroke K M12×1.25 □ 37
f 40 168 f16 58 15 80 55 25 60 183
Max. 5 FF LF+stroke
E 3-GG BB
f 50 M18×1.5 168 f22 58 □ 47 15 86 55 31 60 183
drain port CS
f 63 M18×1.5 171 f22 61 □ 56 15 93 55 38 60 186
f 80 M24×2 188 f28 67 □ 70 19 102 55 47 60 207
f 100 M30×2 194 f36 67 □ 89 23 114 57 57 66 217
The tolerance of MM is f8.
There are check valves on two sides out of the four outer sides of the cap and rod covers except Dimension HM indicates the drain port position.
the port and cushion sides. The check valve is concurrently used with air vent.
When mounting a sensor, refer to the“dimensional drawings of Switch Set” . All the contents With Boots
other than“sensor mounting dimensions”are the same. Symbol
WW X
Hydraulic Cylinders with Position Detector
35P-3
Conex f32 to f63 1/2.5 stroke+X Conex is the registered trademark of Teijin
f80 and f100 1/3 stroke+X Limited.
The boots have been mounted at our
factory prior to delivery.
If the calculated value has a fractional part, round it up.
HH HH
3.5 MPa Hydraulic Cylinder with Position Detector 3.5 MPa Hydraulic Cylinder with Position Detector
14 35P-3 Double Acting Single Rod Unit: mm Unit: mm Double Acting Single Rod 35P-3 15
Dimensional Table
LA Symbol
35P-3 1 LA Bore B Stroke A B B1 BB D EE FP GG
Bore
5 f 32 24 f 30f9 19 7 13 Rc1/4 99 Rc1/8
D
f 40 24 f 30f9 19 7 13 Rc3/8 99 Rc1/8
B f 50 36 f 34f9 24 7 19 Rc3/8 99 Rc1/4
f 63 36 f 34f9 24 9 19 Rc3/8 99 Rc1/4
f 80 48 f 42f9 32 10 24 Rc1/2 107 Rc1/4
WP
f 100 60 f 50f9 41 12 30 Rc1/2 113 Rc1/4
ZJ+stroke BB
0.5□4-core
shielded cable 34 WR WS Max. 5 A W FP P+stroke Symbol
HF HK HP h KK MM P SB SS ST
Bore
24 2-EE
f 32 103 22 81 7 M12×1.25 f 16 58 f9 73 8
A h
HP f 40 106 25 81 7 M12×1.25 f 16 58 f 12 73 8
HF
f 50 115 31 84 11 M18×1.5 f 22 58 f 12 73 12
D B
MM
f 63 122 38 84 11 M18×1.5 f 22 61 f 12 76 12
HK
KK
ST f 80 134 47 87 14 M24×2 f 28 67 f 14 82 19
C Width across flats B1
TS of lock nut for rod SY SU Cushion valves SU SY f 100 155 57 98 17 M30×2 f 36 67 f 18 72 24
end attachment
US 4-SB XR SS+stroke
3-GG XW+stroke Symbol
drain port SU SY TS US W WP WR WS XR XW ZJ
Bore
Port position Ⓑ Port position Ⓓ f 32 18 10 69 84 15 80 55 25 100 173 183
f 40 24 10 80 100 15 80 55 25 100 173 183
A A Note) Dimension“a”for port position Ⓑ or Ⓓ.
Bore f 50 24 10 92 112 15 86 55 31 100 173 183
D B a a D B f 32 f 40 f 50 f 63 f 80 f 100 f 63 24 10 108 128 15 93 55 38 100 176 186
Symbol
C C f 80 32 13 128 150 19 102 55 47 112 194 207
a 5 6 6 0 0 0
The same applies to the Switch f 100 27 18 154 182 23 114 57 57 127 199 217
Set Cylinders.
The tolerance of MM is f8.
There are check valves on two sides out of the four outer sides of the cap and rod covers With Boots
except the port and cushion sides. The check valve is concurrently used with air vent. Symbol
When mounting a sensor, refer to the“dimensional drawings of Switch Set” . All the contents WW X
other than“sensor mounting dimensions”are the same. Bore
Hydraulic Cylinders with Position Detector
35P-3
Conex f32 to f63 1/2.5 stroke+X Conex is the registered trademark of Teijin
f80 and f100 1/3 stroke+X Limited.
The boots have been mounted at our
factory prior to delivery.
If the calculated value has a fractional part, round it up.
HH HH
3.5 MPa Hydraulic Cylinder with Position Detector 3.5 MPa Hydraulic Cylinder with Position Detector
16 35P-3 Double Acting Single Rod Unit: mm Unit: mm Double Acting Single Rod 35P-3 17
Dimensional Table
LB Symbol
35P-3 1 LB Bore B Stroke A AB AE AH AL AO AT B B1
Bore
f 32 24 f9 114 33 23 10 5 f 30f9 19
f 40 24 f 12 116 35 25 12 5 f 30f9 19
5
f 50 36 f 12 125 41 26 12 6 f 34f9 24
D
f 63 36 f 12 132 48 28 12 6 f 34f9 24
B
f 80 48 f 14 146 59 34 14 8 f 42f9 32
f 100 60 f 18 168 70 40 18 9 f 50f9 41
Symbol
D EE FP GG HP h KK LF MM
Bore
ZA+stroke f 32 13 Rc1/4 99 Rc1/8 81 7 M12×1.25 168 f 16
WP
XA+stroke f 40 13 Rc3/8 99 Rc1/8 81 7 M12×1.25 168 f 16
0.5□4-core
shielded cable 34 WR WS Max. 5 A W FP P+stroke
f 50 19 Rc3/8 99 Rc1/4 84 11 M18×1.5 168 f 22
2-EE f 63 19 Rc3/8 99 Rc1/4 84 11 M18×1.5 171 f 22
24
f 80 24 Rc1/2 107 Rc1/4 87 14 M24×2 188 f 28
A h
HP f 100 30 Rc1/2 113 Rc1/4 98 17 M30×2 194 f 36
AE
D B
MM Symbol
P R SA UA W WP WR WS XA ZA
AH
KK Bore
AT
Width across flats B1 Cushion valves f 32 58 33 214 54 15 80 55 25 206 216
C of lock nut for rod
R end attachment AL LF+stroke AL
f 40 58 37 218 60 15 80 55 25 208 220
UA 4-AB 3-GG AO SA+stroke AO
drain port f 50 58 47 220 70 15 86 55 31 209 221
f 63 61 56 227 80 15 93 55 38 214 226
f 80 67 70 256 97 19 102 55 47 241 255
f 100 67 89 274 120 23 114 57 57 257 275
The tolerance of MM is f8.
There are check valves on two sides out of the four outer sides of the cap and rod covers except
the port and cushion sides. The check valve is concurrently used with air vent. With Boots
When mounting a sensor, refer to the“dimensional drawings of Switch Set” . All the contents Symbol
other than“sensor mounting dimensions”are the same. WW X
Bore
Hydraulic Cylinders with Position Detector
35P-3
Conex f32 to f63 1/2.5 stroke+X Conex is the registered trademark of Teijin
f80 and f100 1/3 stroke+X Limited.
The boots have been mounted at our
factory prior to delivery.
If the calculated value has a fractional part, round it up.
HH HH
3.5 MPa Hydraulic Cylinder with Position Detector 3.5 MPa Hydraulic Cylinder with Position Detector
18 35P-3 Double Acting Single Rod Unit: mm Unit: mm Double Acting Single Rod 35P-3 19
Dimensional Table
FG Symbol
35P-3 1 FG Bore B Stroke A B B1 BB D EE EF FB FF
Bore
f 32 24 f 30f9 19 7 13 Rc1/4 47 f7 15
f 40 24 f 30f9 19 7 13 Rc3/8 52 f7 15
5 f 50 36 f 34f9 24 7 19 Rc3/8 65 f9 15
D f 63 36 f 34f9 24 9 19 Rc3/8 76 f9 15
f 80 48 f 42f9 32 10 24 Rc1/2 95 f 12 20
B
f 100 60 f 50f9 41 12 30 Rc1/2 115 f 14 20
Symbol
FP GG GP GR HG HH h KK
Bore
f 32 99 Rc1/8 35 65 100 104.5 7 M12×1.25
WP
f 40 99 Rc1/8 35 65 100 107 7 M12×1.25
0.5□4-core f 50 99 Rc1/4 43 67 110 116.5 11 M18×1.5
shielded cable 34 WR WS Max. 5 3-GG A W FP P+stroke
drain port f 63 99 Rc1/4 49 66 115 122 11 M18×1.5
2-EE
f 80 107 Rc1/4 60 68 128 134.5 14 M24×2
24
A h f 100 113 Rc1/4 70 70 140 155.5 17 M30×2
HH Symbol
EF RA D B LF LL MM P RA UG W WP WR WS
B MM
Bore
f 32 168 153 f 16 58 33 114 15 80 55 25
C Cushion valves
KK
4-FB GR GP 5 LL+stroke f 40 168 153 f 16 58 37 114 15 80 55 25
Width across flats B1 of lock
HG FF
nut for rod end attachment LF+stroke BB f 50 168 153 f 22 58 47 128 15 86 55 31
UG f 63 171 156 f 22 61 56 133 15 93 55 38
f 80 188 168 f 28 67 70 152 19 102 55 47
f 100 194 174 f 36 67 84 166 23 114 57 57
The tolerance of MM is f8.
There are check valves on two sides out of the four outer sides of the cap and rod covers except
the port and cushion sides. The check valve is concurrently used with air vent. With Boots
When mounting a sensor, refer to the“dimensional drawings of Switch Set” . All the contents Symbol
other than“sensor mounting dimensions”are the same. WW X
Bore
Hydraulic Cylinders with Position Detector
35P-3
Conex f32 to f63 1/2.5 stroke+X Conex is the registered trademark of Teijin
f80 and f100 1/3 stroke+X Limited.
The boots have been mounted at our
factory prior to delivery.
If the calculated value has a fractional part, round it up.
HH HH
3.5 MPa Hydraulic Cylinder with Position Detector 3.5 MPa Hydraulic Cylinder with Position Detector
20 35P-3 Double Acting Single Rod Unit: mm Unit: mm Double Acting Single Rod 35P-3 21
Dimensional Table
FH Symbol
35P-3 1 FH Bore B Stroke A B B1 D EE EH FB FF
Bore
f 32 24 f 30f9 19 13 Rc1/4 56 f7 15
f 40 24 f 30f9 19 13 Rc3/8 60 f7 15
5 f 50 36 f 34f9 24 19 Rc3/8 70 f9 15
D f 63 36 f 34f9 24 19 Rc3/8 84 f9 15
Symbol
FP GG HE HP HR h KK LF
WP Bore
35P-3
Conex f32 to f63 1/2.5 stroke+X Conex is the registered trademark of Teijin
f80 and f100 1/3 stroke+X Limited.
The boots have been mounted at our
factory prior to delivery.
If the calculated value has a fractional part, round it up.
HH HH
3.5 MPa Hydraulic Cylinder with Position Detector 3.5 MPa Hydraulic Cylinder with Position Detector
22 35P-3 Double Acting Single Rod Unit: mm Unit: mm Double Acting Single Rod 35P-3 23
Dimensional Table
CT D
5
Symbol
35P-3 1 CT Bore B Stroke A B B1 CD D E EE
B Bore
f32 to f80 f 32 24 f 30f9 19 f 12H9 13 □ 44 Rc1/4
WP
f 40 24 f 30f9 19 f 14H9 13 □ 50 Rc3/8
A W FP P+stroke Max. 5 WS WR 34
f 50 36 f 34f9 24 f 14H9 19 □ 62 Rc3/8
2-EE f 63 36 f 34f9 24 f 14H9 19 □ 76 Rc3/8
LR 24
f 80 48 f 42f9 32 f 20H9 24 □ 94 Rc1/2
h CD A
HP f 100 60 f 50f9 41 f 25H9 30 □ 114 Rc1/2
HF
B D
MM Symbol
MR HK EW FP GG HF HK HP h KK
Bore
KK Cushion valves
C 0
Width across flats B1 LF+stroke L EW f 32 16−0.07 99 Rc1/8 103 22 81 7 M12×1.25
of lock nut for rod 0
end attachment XC+stroke E f 40 20−0.084 99 Rc1/8 106 25 81 7 M12×1.25
3-GG ZC+stroke f 50 0
20−0.084 99 Rc1/4 115 31 84 11 M18×1.5
drain port
WP f 63 0
20−0.084 99 Rc1/4 122 38 84 11 M18×1.5
f100
Max. 5 WS WR 34
0
A W FP P+stroke f 80 32−0.1 107 Rc1/4 134 47 87 14 M24×2
0
f 100 40−0.1 113 Rc1/4 155 57 98 17 M30×2
2-EE LR
24
h CD A Symbol
HP L LF LR MM MR P W WP WR WS XC ZC
Bore
HF
MM B D f 32 19 168 R12 f16 R14 58 15 80 55 25 202 216
HK f 40 19 168 R17 f16 R16 58 15 80 55 25 202 216
KK MR f 50 19 168 R19 f22 R16 58 15 86 55 31 202 216
Cushion valves C
Width across flats B1 LF+stroke L EW f 63 19 171 R19 f22 R16 61 15 93 55 38 205 219
of lock nut for rod
end attachment XC+stroke E
f 80 32 188 R26 f28 R22 67 19 102 55 47 239 259
3-GG ZC+stroke
drain port f 100 53 194 R32 f36 R30 67 23 114 57 57 270 295
The tolerance of MM is f8.
There are check valves on two sides out of the four outer sides of the cap and rod covers except
the port and cushion sides. The check valve is concurrently used with air vent.
With Boots
When mounting a sensor, refer to the“dimensional drawings of Switch Set” . All the contents Symbol
other than“sensor mounting dimensions”are the same. WW X
Bore
Hydraulic Cylinders with Position Detector
35P-3
Conex f32 to f63 1/2.5 stroke+X Conex is the registered trademark of Teijin
f80 and f100 1/3 stroke+X Limited.
The boots have been mounted at our
factory prior to delivery.
If the calculated value has a fractional part, round it up.
HH HH
3.5 MPa Hydraulic Cylinder with Position Detector 3.5 MPa Hydraulic Cylinder with Position Detector
24 35P-3 Double Acting Single Rod Unit: mm Unit: mm Double Acting Single Rod 35P-3 25
AX1**
(reed sensor)・AX2**
(solid state sensor)
f 40 5 4 36 40 72 80 5 2
f 50 4 4 41 45 82 90 5 2
f 63 3 4 47 51 94 102 6 3
UX 30 7 Sensor UX
f 80 3 3 54 59 108 118 4 2
f 100 4 1 63 68 126 136 4 2
RN
Note) Dimension UX indicates the optimum sensor mounting position for detection of stroke end.
RV RV
RY
All dimensions of the cylinders are the same as those of the standard type.
Hydraulic Cylinders with Position Detector
35P-3
HH HH
3.5 MPa Hydraulic Cylinder with 3.5 MPa Hydraulic Cylinder with
26 35P-3 Position Detector Unit: mm Unit: mm Position Detector 35P-3 27
CF
CD
CA
ER RA
CD CA KK
Hydraulic Cylinders with Position Detector
35P-3
KK FR
failure.
A FD FN DO NOT use together with CT
accessory.
FQ
FA FC The lock nut is indispensable in using
the floating joint. Please don't miss to
FJ order the lock nut with the floating joint.
HH HH
3.5 MPa Hydraulic Cylinder with 3.5 MPa Hydraulic Cylinder with
28 35P-3 Position Detector Unit: mm Unit: mm Position Detector 35P-3 29
f 32 46 f12 f3 37 3
2-EB
f 40 58 f14 f3 49 3
f 50 58 f14 f3 49 3
CK
f 63 58 f14 f3 49 3
f 80 78 f20 f3 71 3
EL
f 100 94 f25 f3 87 3
BL
The tolerance of CK is f8.
Hydraulic Cylinders with Position Detector
35P-3