Professional Documents
Culture Documents
Y-G10-A User Manual - EN - Display Receptor
Y-G10-A User Manual - EN - Display Receptor
1.Sketch
3 Func(function) 7 Volume
4 Digit select
2.Function Settings
F01----Store transmitters.
F02----Delete transmitters.
F03----Set the date and time.
F04----Span for rolling display(range:0-99s).
F05----Reminder mode(Chinese broadcast or ring tone).
F06----Select ring tone(7 alternatives).
F07----Mode of displaying the calling records.
F08----Span for auto-deletion of the calling records(range:0-99s).
F09----Restore factory defaults.
1. Enter the setting:Under standby interface,when “FUNC” is being pressed, the receiver will give a sound
of “Di” and show “F01” with the last digit “1” flickering. Then press “ADJUST” to select the intended
number and press “ENT” to execute the directive.
2. Exit the main menu:Under the main menu interface, by pressing “FUNC” to return to homepage, the
receiver will show the date and time again.
3. Retreat:Under the setting interface, press “FUNC” to return to the main menu.
4. Reminder:There are two corresponding ring tones which signals the success or failure of the operation.
There will be a short sound of “Di-Di” if the operation is done properly, and a prolonged sound of “Di-Di-Di”
if the operation fails.
When the broadcast is closed, the receiver will prompt failure if the input figure is out of the setting range.
Note:
1)There are 3 icons indicating 3 different service types
_Call; ﹦Water; ≡Bill
2)Trace calls: under working interface, press “DIGIT SELECT” or “ADJUST”to trace backward or forward
the last 30 calls.
3)Delete calls: under working interface, press “CONFIRM” to delete the calling records one by one.
2.1.F01----Store transmitters
(up to maximum 256 transmitters with code no. ranging from “000” to “999” )
1. By a press on “FUNC”, the screen will show “F01”.
2. By a press on “CONFIRM”, the screen will show “001”.
3. Press “ADJUST” to select the figure or press “DIGIT SELECT” to shift among the digits.
4. By a press on “CONFIRM” once selection is done, the screen will show “001-” with “-” flickering.
5. When press and hold any button of the target transmitter for 2 seconds, there comes a sound of “Di-Di” and
the receiver shows the following number at the same time.
6. Press “FUNC” to return to the main menu.
Note: if one transmitter is stored into the receiver twice with two different code number, the up-dated code
number will replace the former one, and the former one can still be open for storing other transmitter.
2.2.F02----Delete transmitters
1. Press “FUNC”, then the receiver will show “F01” with the last digit “1”flickering.
2. Press “ADJUST” to shift the number to “F02”.
3. Press “CONFIRM”, then the receiver will show “001”.
1) Delete single transmitter
Press “DIGIT SELECT” and “ADJUST” separately to select the figure for deletion.
Press “CONFIRM”, then there comes a sound of “Di-Di” which signals the deletion is completed. Press
“FUNC” twice to return to the homepage.
2) Delete all the transmitters
Press “ADJUST” to adjust the figure to “000”.
Press “CONFIRM”, receiver will show the figure in sequence from 1 to 100, and in the end there comes
Chinese broadcast “设置成功” and the receiver returns to homepage.
2.5.F05----Reminder mode(default:3)
1. By a press on “FUNC”, the receiver will show “F01” with the last digit “1” flickering.
2. Press “ADJUST” to change the figure to “F05”.
3. By a press on “CONFIRM”, the receiver will show “3”.
4. Press “ADJUST” to select the figure among 1,2,3.
(1--Chinese broadcast:需要服务;2--Chinese broadcast:呼叫;3—ring tones)
5. Press “CONFIRM” to store the setting and “FUNC” to return to homepage.
3.Technical Specification
Sensitivity -106dBm