Professional Documents
Culture Documents
CM-CME Grundfoss
CM-CME Grundfoss
CM, CME
Horizontal, multistage centrifugal pumps
50/60 Hz
CM, CME
1
1. Product introduction
Product introduction
The Grundfos CM and CME pumps are horizontal, CME
multistage, end-suction centrifugal pumps. The pumps
are of the close-coupled type and available as either
self-priming or non-self-priming pumps. CM pumps are
fitted with mains-operated motors whereas the motor
for CME pumps has an integrated frequency converter.
Both CM and CME pumps have mechanical shaft
seals.
The CM and CME pumps are available in these three
frequency converter.
Frequency control enables continuously variable
control of the motor speed, which makes it possible to
Cast-iron version set the pump to operation at any duty point. The aim of
continuously variable control of the motor speed is to
adjust the performance to a given requirement.
You can connect a pressure sensor to the built-in
Stainless-steel version
frequency converter on CME pumps. For further
information, see section Sensors for CM, CME on
Fig. 1 Grundfos CM pumps page 143.
The CM pumps are unique products that have been The pump materials are identical to those of the CM
developed in order to fulfil a wide variety of customer pump range.
demands.
The CM pumps are available in various sizes and
numbers of stages to provide the flow rate and
pressure required.
The CM pumps consist of two main components: the
motor and the pump unit. The motor is a Grundfos
motor designed to EN standards. The pump unit
incorporates optimised hydraulics and offers various
types of connections.
The pumps offer many advantages, some of which are
listed below and described in detail in Features and
benefits on page 10:
• compact design
• worldwide usage
• high reliability
• service friendly
• wide performance range
• low noise
• customised solutions.
5
4 CM, CME
High reliability
New state-of-the-art shaft-seal design and materials
10
5 CM, CME
5. Identification
Identification
Example CM 10 - 3 A - R - I - E - A V B E F -A -A -N
Note: The type key cannot be used for ordering as not all combinations are possible.
12
6 CM, CME
Product range
RUUE, RUUV
AVBE, AVBV
CM 5-2 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
CM 5-3 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
CM 5-4 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
CM 5-5 ● ● ● ● ● ● ● ● ●2) ● ● ● ● ● ● ● ● ● ● ●
CM 5-6 ● ● ● ● ● ● ● ●2) ● ● ● ● ● ● ● ● ● ●
CM 5-7 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
CM 5-8 ● ● ● ● ● ● 2) ● ● ● ● ● ● ● ● ● ● ●
CM 5-9 ● ● ● 2) ● ● ●
CM 5-10 ● ● ● 2) ● ● ●
CM 5-11 ● ● ● 3) ● ●
CM 5-12 ● ● ● 3) ●
CM 5-13 ● ● ● 3) ●
CM 10-1 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
CM 10-2 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
CM 10-3 ● ● ● ● ● ● ● ● ●2) ● ● ● ● ● ● ● ● ● ●
CM 10-4 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
CM 10-5 ● ● ● ● ● ● 2) ● ● ● ● ● ● ● ● ● ●
CM 10-6 ● ● ● 2) ● ●
CM 10-7 ● ● ● 3) ●
CM 10-8 ● ● ● 3) ●
CM 15-1 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
CM 15-2 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
CM 15-3 ● ● ● ● ● ● ● ● ●2) ● ● ● ● ● ● ● ● ●
CM 15-4 ● ● ● ● 2) ● ●
CM 25-1 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
CM 25-2 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
CM 25-3 ● ● ● ● 2) ● ●2) ●
CM 25-4 ● ● ● ● 2) ● ●
1)
On request.
2)
Neither suitable for 60 Hz mains-operated pumps, nor for CME pumps running at 100 % speed.
3) Not suitable for pumping liquids at temperatures above 90 °C.
4)
Pumps with supply voltages B and E are supplied for wire connection without a terminal board inside the terminal box (flying wires).
Pumps with supply voltages B1, B2 and E1 are supplied with a terminal board inside the terminal box.
5) Only available with IE2-compliant motors and cannot be exported to the USA.
14
7 CM, CME
7. Performance range
Performance range
CM, 50 Hz
S +
>N3D@ >P@
&0
USP
+]
,62%
&0 &0 &0 &0 &0 &0
4>OV@
CM-A
CM-I/G
CM, 60 Hz
S +
>N3D@ >P@
&0
USP
+]
,62%
&0 &0 &0 &0 &0 &0
TM04 3369 4616
4>PñK@
4>OV@
CM-A
CM-I/G
16
10 CM, CME
10. Construction
Construction
Pump Motor
The pumps have an axial inlet port and a radial outlet CM and CME pumps are fitted with totally enclosed,
port and are mounted on a base plate. fan-cooled, 2-pole motors with principal dimensions to
All movable parts are made of stainless steel. EN 50347. The motors have been developed
Self priming pumps are fitted with an internal water especially for CM and CME pumps.
trap and an internal valve, both of which are mainly Electrical tolerances comply with EN 60034.
made of a composite material. Single-phase CME pumps are available from 0.37 to
You find the sectional drawings on pages 26 to 28. 1.5 kW.
The pumps are available with mains-operated motors Three-phase CME pumps are available from 0.37 to
(CM pumps) and electronically speed-controlled motors 7.5 kW.
(CME pumps). Soft starter
All pumps incorporate a maintenance-free mechanical Soft starters are only to be used for three-phase
O-ring shaft seal with a fixed driver. motors.
Electrical data
Insulation class F
CM
1 x 115/230 V, 60 Hz
1 x 220-240 V, 50 Hz
3 x 208-230/440-480 V, 60 Hz
3 x 220-240/380-415 V, 50 Hz
3 x 200/346 V, 50 Hz; 200-220/346-380 V, 60 Hz
3 x 575 V, 60 Hz
Supply voltages 3 x 380-415 V, 50 Hz; 440-480 V, 60 Hz
(tolerance ± 10 %) 3 x 220-240/380-415 V, 50 Hz
3 x 220-255/380-440 V, 60 Hz
CME
1 x 200-240 V, 50/60 Hz
1 x 208-230 V, 50/60 Hz
3 x 200-240 V, 50/60 Hz
3 x 380-500 V, 50/60 Hz
3 x 440-480 V, 50/60 Hz
24
CM, CME
10
Material specification
Construction
Pump material version
Motor parts
156b Motor flange Cast iron
150 Stator housing Silumin (Alu)
151 Fan cover Composite PBT/PC
153 Ball bearing
Composite PA 66 30 %
156 Fan
GF
158 Corrugated spring Steel
164b Terminal box, MG Composite PC/ASA or
164e Terminal box, MGE silumin (Alu)
1)
On request.
2) As standard, the pumps listed below are fitted with sleeves made of stainless steel 1.4401:
CM, CME 1-9 up to and including CM, CME 1-14
CM, CME 3-9 up to and including CM, CME 3-14
CM, CME 5-9 up to and including CM, CME 5-13
CM, CME 10-6 up to and including CM, CME 10-8.
3)
Only in CM, CME-I/G pumps.
4) Only in CM, CME-A pumps.
5)
STX2000 ~ CrNiMO 22 19 4.
29
15 CM, CME
50 -3
Hgeo NPSH
200 20 -1
10
0 0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Q [m³/h]
Fig. 34 Dimensional data
P2 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0
Q [l/s]
[kW]
5 -8
-7
Pump efficiency
4
-6
3
2
-5
-4 When sizing the pump, the efficiency (eta) must be
-3
1 -2
-1 considered so that the pump will operate at or near its
0
p NPSH
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Q [m³/h]
Eta
maximum efficiency, for instance on the right-hand
[%]
side in the curve example in fig. 35.
TM04 6404 5112
38
16 CM, CME
p H
[kPa] [m] Pump type, speed,
130
CM 5 frequency and ISO
-13 2900 rpm standard.
1200
120 50 Hz
-12 ISO 9906:2012 3B
110
-11
1000
100
-10 QH curve for the individual
90 pump.
-9 The bold curves indicate
800 80 the recommended duty
-8
range for best efficiency.
70
-7
Number of stages.
600 60
-6
50 -5
400 40 -4
30 -3
200 20 -2
10
40