Professional Documents
Culture Documents
FP6606AC: USB Dual Ports Charging Controller USB-PD/HVDCP For Type-C and HVDCP For Type-A
FP6606AC: USB Dual Ports Charging Controller USB-PD/HVDCP For Type-C and HVDCP For Type-A
FP6606AC: USB Dual Ports Charging Controller USB-PD/HVDCP For Type-C and HVDCP For Type-A
● Power Strip
DNA
SUA
DPA
20 19 18 17 16
● USB Power Output Ports
SENA 1 15 VBUSC
VDD 4 12 DPC
FP6606AC□□
FBO 5 11 DNC Package Type
6 7 8 9 10
W4: TQFN-20L (3mmx3mm)
P6: CPC-20L
ISMC
ISMA
MPC
ISPC
ISPA
ww
Option Code
P6 Package CPC-20L Please Reference
Option Code Information
DPA 1 20 VBUS
DNA 2 19 SRCGC Option Code Information(USB PD)
SUA 3 18 VBUSC Option Code 5V 9V 12V 15V 20V Capability Package
SENA 4 17 CC 1
FLAGA 5 16 CC2 A 3A 2A 1.5A - - 18W W4
GND 6 15 DPC
D 3A 3A 2.5A 2A - 30W W4
VDD 7 14 DNC
FBO 8 13 ISPC L 3A 3A - 2A 1.5A 30W P6
MPC 9 12 ISMC
ISPA 10 11 ISMA M 3A 3A - 3A 2.25A 45W P6
FP6606AC-Preliminary 0.92-JUL-2019 1
FP6606AC
Typical Application Circuit
VIN
Q1
8 1
Buck VBUS 7
D
D
S
S
2
VBUSC
6 3
Converter 5
D
D
S
G
4
PW34XX
FB
100kΩ
RVDD
RFB D1
2.7kΩ
1N4148
CVDD Type-C
10μF
VDD VBUS A1 B12
A2 B11
GND SRCGC
A3 B10
FBO VBUSC A4 B9
MPC CC1 A5 B8
SENA CC2
A6 B7
D-
FP6606AC A7 B6
D+
100kΩ FLAGA DPC A8 B5
SUA DNC A9 B4
A10 B3
ISMA ISPA
10mΩ
TDM3478
Type-A
VBUS
D-
D+
GND
RFLAGA
6
7
8
5
10kΩ
D
D
D
D
PW3428
80.6kΩ
Q1-1
G
S
S
S
4
3
2
1
10mΩ
FP6606AC-Preliminary 0.92-JUL-2019 2
FP6606AC
车载充电器
SENA 4 1 Detection function Pin. Detect USB Type-A whether is device existence.
N-MOSFET gate node control. When Type-A plug in, FLAGA function will be activated high,
FLAGA 5 2
Type-A plug out, FLAGA pin will be activated low.
Power ground. The exposed pad must be connected to GND and well solder to a large PCB
GND 6 3
copper area for maximum power dissipation.
FBO 8 5 Output voltage control pin. Current sink\source function for FB node.
Positive input of current sense amplifier of Type-A. Connect to the current sense resistor on
ISPA 10 7
the VBUS power path.
Negative input of current sense amplifier of Type-A. Connect to the current sense resistor on
ISMA 11 8
the VBUS power path.
Negative input of current sense amplifier of Type-C. Connect to the current sense resistor on
ISMC 12 9
the VBUS power path.
Positive input of current sense amplifier of Type-C. Connect to the current sense resistor on
ISPC 13 10
the VBUS power path.
FP6606AC-Preliminary 0.92-JUL-2019 3
FP6606AC
Absolute Maximum Ratings (Note 1)
● Input Supply Voltage VDD ----------------------------------------------------------------------------- -0.3V to +7V
● DPA, DNA, SUA, SENA -------------------------------------------------------------------------------- -0.3V to +24V
● CC1, CC2 ,DPC,DNC ----------------------------------------------------------------------------------- -0.3V to +24V
● SRCGC, VBUS, VBUSC ------------------------------------------------------------------------------- -0.3V to +35V
● ISPA, ISMA, ISPC, ISMC ------------------------------------------------------------------------------- -0.3V to +6.5V
● FBO, MPC, FLAGA -------------------------------------------------------------------------------------- -0.3V to +6.5V
● Maximum Junction Temperature (TJ) ---------------------------------------------------------------- +150°C
● Storage Temperature (TS) ------------------------------------------------------------------------------ -65°C to +150°C
● Lead Temperature (Soldering, 10sec) -------------------------------------------------------------- +260°C
● Package Thermal Resistance, (θJA) (Note 2)
CPC-20L ---------------------------------------------------------------------------------------- TBD
TQFN-20L(3mmx3mm) --------------------------------------------------------------------- 68°C/W
● Package Thermal Resistance, (θJC)
CPC-20L ---------------------------------------------------------------------------------------- TBD
TQFN-20L(3mmx3mm) --------------------------------------------------------------------- 30°C/W
Note 1: Stresses beyond this listed under “Absolute Maximum Ratings" may cause permanent damage to the device.
Note 2: θJA is measured at 25°C ambient with the component mounted on a high effective thermal conductivity test board of JEDEC-51-7.
FP6606AC-Preliminary 0.92-JUL-2019 4
FP6606AC
Electrical Characteristics
(VDD=5V, TA=25°C and the recommended supply voltage range, unless otherwise specified.)
Parameter Symbol Conditions Min Typ Max Unit
Input Power
VBUS
USB Type-A
(Note 3)
DPA/DNA OV Threshold V_DPDNOV In QC Mode 4 V
USB Type-C
(Note 3)
DPC/DNC OV Threshold V_DPDNOV In QC Mode 4 V
(Note 3)
CCOV Rising V_CCOV-rising 1.04*VDD V
(Note 3)
CCOV Falling V_CCOV-falling VDD V
FP6606AC-Preliminary 0.92-JUL-2019 5
FP6606AC
Electrical Characteristics (Continued)
(VDD=5V, TA=25°C and the recommended supply voltage range, unless otherwise specified.)
Parameter Symbol Conditions Min Typ Max Unit
TGLITCH(V)
Output Voltage Glitch Filter Time 20 40 60 ms
CHANGE
TGLITCH-CONT-
Continuous Mode Glitch Filter Time 100 200 ms
CHANGE
VDD=3.2 to 6.4V
DPA Leakage Resistance RDAT-LKG VDPA=0.6-3.6V Switch 300 500 800 kΩ
SW1=off
Apple Mode
Over-Current Protection
FP6606AC-Preliminary 0.92-JUL-2019 6
FP6606AC
Function Description
Multi-Ports Control Data Line Interface (D+/D-)
Use for single VBUS source and multi USB FP6606AC supports QC 2.0/3.0 and FCP protocol on
channel applications. Connect all MPC pins on the D+/D− data line. The related registers are
different Fitipower USB ICs together and connect a assigned to the vendor define registers. When the
100kΩ resistor to GND. FP6606AC will auto detect FP6606AC is configured as QC 2.0/3.0/FCP mode,
the attachments between all Fitipower USB ICs both D+ and D− pin are applied to 2.7V. If sink device
and will auto decide multi-ports operation is has the function of QC 2.0/3.0/FCP, D+ pin will be
allowed or not. forced between 0.325V and 2V. In the meanwhile,
D+ pin will be automatically connected to D− pin by
Plug In Detect FP6606AC and this process is called the short mode
When device plugs in or out, the FP6606AC can for USB BC1.2 specification. If D+ is continuously
auto detect and into standby or operation mode. applied to the voltage between 0.325V and 2V for
1. Plug In detection is used for USB device plug in. 1.25 seconds, the FP6606AC will enter QC
When device plug in, FLAGA pin alerts active 2.0/3.0/FCP operation mode. The QC 2.0/3.0 could
high. be classed as the following table.
2. Plug Out detection is used for USB device plug
out. When plug out detected, FLAGA pin active D+ D- Output Voltage
low. 0.6V 0.6V 12V
USB Port GND
3.3V 0.6V 9V
0.6V 3.3V Continuous mode
0.6V High-Z 5V (Default)
SUA
FLAGA Plug In
S Q FLAGA
Detection
FP6606AC-Preliminary 0.92-JUL-2019 7
FP6606AC
Outline Information
CPC-20L Package (Unit: mm)
Carrier dimensions
FP6606AC-Preliminary 0.92-JUL-2019 8
FP6606AC
Outline Information (Continued)
TQFN-20L 3mm×3mm ( pitch 0.4mm ) Package (Unit: mm)
Carrier dimensions
FP6606AC-Preliminary 0.92-JUL-2019 9