Professional Documents
Culture Documents
Armix AFA 160E Ver 7
Armix AFA 160E Ver 7
Armix AFA 160E Ver 7
Product Description
Armix AFA 160(E) is a high performance alkali free ready to use set accelerator for sprayed concrete applications. it is
commonly used for the wet mix sprayed concrete processes in the tunneling and mining industry. Armix AFA 160(E) is a liquid
admixture, by adjusting the dosage, setting times and rebound can be reduced providing a safe and efficient work
environment. Armix AFA 160(E) meets the requirements of EN 934-5 admixture for sprayed concrete, ASTM C1141 standard
specification for shotcrete admixture and EFNARC
Rock support in tunnels and mines Rapid set and continued high early age strength allows
Slope stabilization thick sections to be built up.
Used in poor ground conditions Low dust emission during application ensures a safe
Backfilling grouts for TBM tunnel lining and suitable working environment
Accelerated cementitious injection grout High final compressive strength development after 28
days
and excellent long term durability.
free from alkali thus improving working environment
Minimum rebound when using the correct nozzle angle
and distance
Application Methodology
Dispersing and mixing
Before spraying of concrete, poor and loose rock
Armix AFA 160(E) is dosed and added on site by a liquid
should be removed from the surface.
dispensing system. optimum dispersion in the shotcrete
Water leakages should be drained out ,either by is governed by nozzle configuration and shotcreteing
drainage channels or should be blocked by grouting techniques, for optimum performance The w/c ratio
Pre-wetting should be carried out, big cavities should be designed below 0.45.this ensures rapid setting
should be carefully built up before the main and lower set accelerator dosage. When targeting
extremely high early strength ,the w/c ratio 0.40 or lower.
applications
the lower w/c ratios provide faster setting high early
Spraying should start from the bottom and continue strength ,better durability ,lower accelerator dosage and
upwards. this is to avoid spraying in rebound losses thick layer can be applied overhead.
0
The nozzle direction should be maintained 90 to the MYK arment always recommend that trial should be
surface carried out to confirm suitability of the product. please
note regional climatic condition may cause a variation in
the performance of product
It is recommended to use only fresh cement as the age
The MYK Armix series of superplasticisers and hydration
of the cement can have a negative influence on the controlling system are fully compatible with Armix AFA
setting characteristics of the mix. Armix AFA 160(E) can and to optimize the sprayed concrete performance on
be sensitive to the type of cement. With some cements site. Do not mix or interchange ARMIX AFA160E with
the setting characteristics can be too slow. it is strongly any type of accelerator produced by another
recommended to do preliminary tests to check setting manufacturer, as this can cause unexpected behavior.
and 24 h strength.
1 of 3 1 of 3
Ver/7/Oct 2021
Admixtures & Surface Treatment
ArmixAFA 160(E)
High performance Alkali-free Liquid Set accelerator
High
for sprayed performance
concrete Alkali-free, Po
application
Typical setting time Overdosing (>10%) may result in decreased final strength
As per ASTM C 1102
(Depending on Cement and w/c ratio)
Ver/7/Oct 2021 2 of 3
2 of 3
Admixtures & Surface Treatment
Fire
Armix AFA 160(E) is water based and non-flammable
Legal Note
The information, and, in particular, the recommendations relating to the application and end-use of MYK Arment products, are given in good
faith based on MYK Arment current knowledge and experience of the products when properly stored, handled and applied under normal
conditions in accordance with MYK Arment’s recommendations. In practice, the difference in materials, substrates and actual site conditions are
such that no warranty in respect of merchant ability or of fitness for a particular purpose, nor any liability arising out of any legal relationship
whatsoever, can be inferred either from this information, or from any written recommendations, or from any other advice offered. The user of the
product must test the product's suitability for the intended application & purpose. MYK Arment reserves the right to change the properties of its
products. The proprietary rights of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery.
Users must always refer to the most recent issue of the local product data sheet for the product concerned, copies of which will be supplied on
request.
Ver/7/Oct 2021 3 of 3