Professional Documents
Culture Documents
27 Jan
27 Jan
Quotes
USE MAX DISCOUNT CODE Y579
Lap splices shall not be used for bars larger than
(a) 32 mm
N
(b) 40 mm
(c) 46 mm
(d) 36 mm
USE MAX DISCOUNT CODE Y579
Which one of the following is not a compression member?
(a) Strut
(b) Tie
(c) Rafter
(d) Boom
USE MAX DISCOUNT CODE Y579
Distempers are generally used to coat ______.
(a) Compound wall
(b) External concrete surfaces
(c) Interior surface which are not exposed to environment
(d) Wood works
Paste Here Motivation
Quotes
USE MAX DISCOUNT CODE Y579
Compression index developed by Casagrande is
(a) CV = 0.009 (LL + 10%)
(b) CV = 0.009 (LL – 10%)
*
(c) Lap
(d) Edge distance
USE MAX DISCOUNT CODE Y579
Centre-to-centre distance of adjacent rivet or bolt holes measured
in the direction of stress is known as:
(a) Gauge
(b) Pitch
(c) Lap
(d) Edge distance
USE MAX DISCOUNT CODE Y579
A square column section of size 350 × 350 mm is reinforced with
four bars of 25 mm diameter and four bars of 16 mm diameter;
then the transverse steel should be
(a) 5 mm dia @ 240 mm c/c
(b) 6 mm dia @ 300 mm c/c
(c) 8 mm dia @ 250 mm c/c
(d) 8 mm dia @350 mm c/c
USE MAX DISCOUNT CODE Y579
The void ratio of a given soil A is twice that of another soil B, while
the effective size of Particles of soil A is one-third of that of soil B.
The ratio of height of capillary rise of water in soil A to that B will
be
(a)0.67
(b) 1.0
(c) 1.5
(d) 2.0
USE MAX DISCOUNT CODE Y579
What is the maximum distance between two consecutive bolts (in
tension) if the plate thickness is 14 mm?
(a) 160 mm
(b) 200 mm
(c) 224 mm
(d) 208 mm
USE MAX DISCOUNT CODE Y579
A welded steel plate girder consisting of two flange plates of 350
mm × 16 mm and a web plate of 1000 mm × 6 mm, requires
(a) No stiffeners
(b) Horizontal stiffeners
(c) Intermediate vertical stiffeners
N
(c) 2.00 cu m
(d) 1.00 cu m
USE MAX DISCOUNT CODE Y579
Neglecting axial deformation, the kinematic indeterminacy of the
structure shown in the figure below is
(a) 12
(b) 14
.
(c) 20
(d) 22 -
... -
USE MAX DISCOUNT CODE Y579
A steel rod of 16 mm diameter has been used as a tie in a bracing
system but may be subjected to a possible reversal of stress due to
the wind. What is the maximum permitted length of the member?
(a) 1600 mm
(b)
↑
1400 mm
(c) 1200 mm
(d) 1000 mm
USE MAX DISCOUNT CODE Y579
The contact pressure for a rigid footing resting on clay at the
centre and the edges are respectively
(a) Maximum and zero
(b) Maximum and minimum
(c) Zero and maximum
(d) Minimum and maximum
a
USE MAX DISCOUNT CODE Y579
The tolerance in the width of mould of a class I brick is about:
(a) ±3 mm
(b) ±6 mm
S
(c) ±10 mm
(d) ±12 mm
USE MAX DISCOUNT CODE Y579
The basic value for vertical deflection of span to effective depth
ratio for span up to 10 m for simply supported beam is
(a) 7
(b) 12
(c) 20
(d) 26
USE MAX DISCOUNT CODE Y579
As per IS 13311 (Part 1), in the ultrasonic test for hardened
concrete, good quality of concrete is indicated if the pulse velocity
is:
(a) 3.0 km/s to 3.5 km/s
(b) 3.5 km/s to 4.5 km/s
sit