Professional Documents
Culture Documents
Cell Reselection To LTE in CELL-FACH
Cell Reselection To LTE in CELL-FACH
USER DESCRIPTION
Disclaimer
The contents of this document are subject to revision without notice due to
continued progress in methodology, design and manufacturing. Ericsson shall
have no liability for any error or damage of any kind resulting from the use
of this document.
Trademark List
All trademarks mentioned herein are the property of their respective owners.
These are shown in the document Trademark Information.
Contents
1 Introduction 1
1.1 Basic Characteristics 1
1.2 Benefits 1
1.3 Additional Information 2
3 Parameters 5
3.1 Introduced Parameters 5
3.2 Affected Parameters 5
4 Network Impact 7
4.1 Subscriber Capacity 7
4.2 Network Performance 7
4.3 Hardware 7
4.4 Inter-Node Interface 7
4.5 Other Network Elements 7
6 Performance 11
6.1 KPIs 11
6.2 Counters 11
6.3 Events 11
Reference List 15
1 Introduction
This feature provides the support that the User Equipment (UE) needs to
perform cell reselection from WCDMA to LTE in CELL_FACH state. This
capability is supported by LTE capable UE from 3GPP release 8 (optional) and
3GPP release 11 (mandatory). An indicator ‘‘CELL_FACH Absolute Priority
Measurement Indicator’’ is added to System Information Block type 19 (SIB19)
from 3GPP release 11. It serves as an indication to UE during Radio Access
Technology (RAT) measurements selection when the absolute priority based
cell reselection is enabled.
Feature identity:
FAJ 121 3520: Cell Reselection to LTE in CELL-FACH
Dependencies
1.2 Benefits
The Cell Reselection to LTE in CELL-FACH feature provides the followings
benefits:
• In the WCDMA connected mode, the Release with Redirect to LTE feature
cannot be triggered when lacking the LTE coverage. After switching down
to CELL_FACH state and moving to LTE coverage, UE performs cell
reselection to LTE coverage directly. It is not necessary to depend on
Release with Redirect to LTE feature and wait for transferring of UE state.
Before activating the feature, ensure that the feature FAJ 121 1474: LTE Cell
Reselection is installed and activated in the RNC.
3 Parameters
(1) The operator can modify this attribute only by using Advanced MO Scripting (AMOS), which is
a part of OSS-RC. The OSS-RC can support modifications of this attribute in a later release.
4 Network Impact
This section describes how the Cell Reselection to LTE in CELL-FACH feature
impacts the network functions and capabilities.
When this feature is active, the LTE capable UE with 3GPP release 8 (optional)
and 3GPP release 11 (madatory) in CELL_FACH state can move to LTE
network. Radio network traffic is affected by this feature if a large amount of
such UE is constantly in CELL_FACH state.
4.3 Hardware
No feature specific information is identified.
This section describes how the Cell Reselection to LTE in CELL-FACH feature
affects other features and functions.
6 Performance
6.1 KPIs
This feature has no associated Key Performance Indicators (KPIs).
6.2 Counters
Table 5 lists the counters associated with the Cell Reselection to LTE in
CELL-FACH feature.
Table 5 Counters
Counter Description
UtranCell::pmTotNoRrcConnec Two elements for LTE with CELL-FACH measurement capability
tUeCapability are added to cover the mobility to LTE in CELL_FACH state.
More information about counters can be found in Managed Object Model RNC
and Managed Object Model RBS.
6.3 Events
This feature has no associated events.
This section provides Operation and Maintenance (O&M) information for the
Cell Reselection to LTE in CELL-FACH feature.
7.1.1 Preconditions
The FAJ 121 1474: LTE Cell Reselection feature must be activated before
activation of the FAJ 121 3520: Cell Reselection to LTE in CELL-FACH feature.
7.1.2 Activating
The Cell Reselection to LTE in CELL-FACH feature is activated by doing as
follows:
• Order and install FAJ 121 3520: Cell Reselection to LTE in CELL-FACH
with the license key CXC 403 0153 in the RNC.
7.2.1 Preconditions
7.2.2 Deactivating
The FAJ 121 3520: Cell Reselection to LTE in CELL-FACH feature is deactivated
on the RNC level by setting the RncFeature::CellReselectLteInFach
parameter to DEACTIVATED.
Reference List