Professional Documents
Culture Documents
File 1453370423
File 1453370423
14 blue
OPERATION INSTRUCTION 12
ELECTRIC DIAGRAM 15
15
B25F Mixer Parts List B25F Mixer Parts List
PARTS CATALOG TROUBLE SHOOTING AND SPECIFICTION
OVERVIEW
TROUBLE SHOOTING
1
Trouble Possible Causes Re-cover
The axle can't work when operate Poor contact of the electrical equi-
2 the machine. pment. Check the plug.
Item Descviption
The mixing bowl out of position. Moving direction is not correct.
3 1 cover
Leak oil. Sealing washer is damaged. Change.
2 rear cover
5 Defficult to move the bowl up and Slideway is rusted.
ring Clean the slideway and lubrication.
4 3 down.
Mixing device The motor is overheat and speed The voltage is not enough, or inco- Check the voltage or use lower s-
4 down. rrect speed. peed.
5 french Noise and over heat. Poor lubrication. Add or change lubrication.
6 bowl The mixing device or bowl deform- Repair or change the bowl or mixi-
Mixer touch the bowl.
ed. ng device.
6
SPECIFICTION
NOTES:
Type B30F B30F
The no using pipe line sprays to wash
the mixer. Mixer(L) 25 25
548 462
While maintaining the mixer, must pull Mixing
out first the power supply plug, and from Speed 317
376
profession the personnel maintains. (r.p.m)
208 197
Maxflour Capacity(kg) 6 6
1 14
B25F Mixer Parts List B25F Mixer Parts List
SPECIAL ATTENTION
1 BEFORE USING , PLEASE CLEAN THE BOWL AND THE MIXING DEVICES CAR-
NOTES£
EFULLY, AND THEN INSTALL THE BOWL ONTO THE MACHINE CORRECTLY Machine at a factory hour have added to
AND TIGHTLY; note the superior quality lubricates the
grease, usually the circumstance bottom
2 WHEN CHOOSING MIXING DEVICES, PLEASE REFER TO THE OPERATION MA- cover (4)
can use for several years, but machine is
NUAL TO CHOSE THE CORRECT SPEED, OR IT WILL DESTORY THE INSIDE SPA- after maintaining, must replace the lubri-
RE PARTS AND SHORTEN THE USING LIFE OF THE MACHIE; cation grease.
3 AFTER USING, PLEASE POWER OFF THE MACHINE, AND PUT THE BOWL AND
DEVICES IN THE SAFE AND CLEAN PLACE AFTER CLEANING; Fill with the lubrication grease empress,
please the cover the tight noting the oil b-
4 KEEP ENVIROMENT ARROUND THE MACHINE DRY、HEALTH AND SAFE.
cover (10)
ore cover.
In order to keep safety, when using Mixing device I/II/III , Please pay attention to insert their
grooves which are from the handles into the spiral axle pin separately. Furthermore, rising the
bowl to the highest positon, so that the edge of the bowl is higher than Mixing device I/II/III
working position.
13 2
B25F Mixer Parts List B25F Mixer Parts List
Figure 2 AXLE
OPERATION INSTRUCTION
Item Descviption Qty
20 110V
1 baffle 1 380V 220V
10 Before using, please check power supply if it match
230V
2 roller 8*16 4 240V
1 your machine and be sure ground wire is eliable.
16 3 spring 8
4 engager 1
5 gear ring 1
11 5 Before testing, please take mixing device off first, in
6 dividing ring 1 order to avoid damage machine which is match mo-
12
17 7 joint gear 1 ving direction. It's necessary to change the three-ph-
3 2 8 bearing ring 1 ase machine if the moving direction is not match wi-
13
18
4 9 joint 1 th arrow.
10 bearing ring 1
15
6 1
11 joint gear I For changing the speed: Please stop machine first
14
7
12
13
ring
bearing 6205
1
1
OFF before change speed in order to aviod damage gear
box.
19
14 oil seal Pd30*45*10 1
8 15 sleeve 1
16 axle 1 Mixing: according to the different mixing-material.
9 1
Choose the different mixing devices and speed.
17 key 6*14
18 key 5*35 2
19 key 6*30 1
Vertical sides of jaws must face A: Be suitable for mix and stir butter, eggs, and work wi-
on another. 20 bearing 6003 1 A
th in high speed, working time is less than 15 minutes.
NOTES£ B. Be suitable for mix and stir stuffing and raw material,
Be sure to install correct position B and work in middle speed, working time is less than 20
(see Figure 2-1) and lubricate all
of the pins in the sleeve drive wh- minutes.
en reassembling. C: middle position is suitable for mixing dough,
RIGHT WRONG Joint (9) must always be raised C working time is less than 30 minutes.Flour wat-
and lowered smoothly. Be sure jo- er quantity is 40%-50%.
FIGURE 2-1 FIGURE 2-2 int sleeve as shown in Figure 2-2.
Check oil seal (14), if serious oil le-
aks from drip cup.
3 12
B25F Mixer Parts List B25F Mixer Parts List
2 gear axle 1
3 key 5*11 1
1 4 key 5*11 1
6
5 gear 1
6 stop ring 1
7 7 gear 1
8 stop ring 1
1 2 3
2 9 bearing 6201 1
8
3
Item Descviption Qty
1 Mixing device I 1
2 Mixing device II 1 9 4
NOTES£
NOTES£ At the center in the shaft unit. To the
4
Any agitator is easily installed by simp- gear axle (2) above is the gear shaft and gear sh-
ly raising it onto the mixing axle, and
aft I (see figure 3-1 ).
then rotating it clockwise on the shaft
until into place. To remove, raise the a- gear axle I C-type stop ring(6/8) has to be fixed
gitator on the shaft until it clears the loc- when reassembling.
k and then rotate counter-clockwise and spiral
Be sure that the keys are inserted
lower.
for each gear.
All of tools are precisely fitted to the bo-
axle
wl, rounded corners and easily remov- fork
eable for cleaning.
FIGURE 3-1
11 4
B25F Mixer Parts List B25F Mixer Parts List
9 bearing 6203 1
3 10 bearing 6204 1
11 oil seal Pd25*50*10 1
3 12 key 5*18 1
10
13 Mixing axle 1
14 Pin 1
4 11
4
12
5 13
6 NOTES£
5-1
C-type stop ring(5) has to be fixed
when reassembling.
14
5-2
5 10
B25F Mixer Parts List B25F Mixer Parts List
9 6
B25F Mixer Parts List B25F Mixer Parts List
Figure6 FORK AND SPEED SHAFT Figure 7 MACHINE SEAT, STAND AND HANDWHEEL TYPEBOWL LIFTER UINT
3 1 axle 1 7 1 arm 1
1 18
2 nut 1 2 stand 1
4
3 spring 1 3 slide 1
8
4 shaft 1 20 4 plate 1
5 fork 1 5 gear 1
1 2
6 pin 3*20 1 6 support seat 1
7 eccentricity knot 1 7 capacitor board 1
17
8 steel ball 3 8 capacitor 200uF 1
8 13 handwheel 1
7 2 4
9 NOTES£ 14 nut M10 1
The speed selector / shifting mech- 1
15 handle
12 anism is designed for simplicity and
16 handle screw 1
11 reliability. It features three mixing s- 3
17 machine seat 1
10 peeds.
9 18 safefy covering switch 1
Speed selection is made by aligning
the pointer of the shifter handle with 10 19 fluctuate safety switch 1
copper (8)
the proper number on the shift sele- 20 overload protection switch 1
ctor. Stop the mixer befor making any
speed changes.
Apply sealant to the shift selector as-
15
sembly, and install it .
16
fork (5) 11
speed block (10)
12
FIGURE6-1 13 14
7 8