Professional Documents
Culture Documents
307-01 Automatic Transmission 10 Speed - Removal and Installation - Transmission Fluid Pan, Gasket and Filter
307-01 Automatic Transmission 10 Speed - Removal and Installation - Transmission Fluid Pan, Gasket and Filter
307-01 Automatic Transmission 10 Speed - Removal and Installation - Transmission Fluid Pan, Gasket and Filter
Materials
Name Specification
Motorcraft® MERCON® ULV Automatic Transmission Fluid WSS-M2C949-A
XT-12-QULV MERCON® ULV
Removal
3. NOTE: Note the location of the bolts and studbolts for assembly.
Remove the transmission fluid pan bolts and the transmission fluid pan and allow the transmission
fluid to drain.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 2 of 10
4. NOTE: The transmission fluid pan gasket can be reused if not damaged.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 3 of 10
5. NOTE: The transmission fluid filter may be reused if no excessive contamination is indicated.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 4 of 10
Installation
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 5 of 10
1. NOTE: If the transmission is being repaired for a contamination-related failure, install a new
transmission fluid filter and seal assembly. The transmission fluid filter may be reused if no excessive
contamination is indicated.
Inspect the transmission fluid filter seal. If necessary, replace the transmission fluid filter seal.
2. Lubricate the transmission fluid filter seal with automatic transmission fluid.
Material: Motorcraft® MERCON® ULV Automatic Transmission Fluid / XT-12-QULV (WSS-M2C949-
A) (MERCON® ULV)
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 6 of 10
3. NOTICE: If the bolts are installed in the wrong locations, transmission damage will occur.
NOTE: The transmission fluid filter may be reused if no excessive contamination is indicated.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 7 of 10
4. NOTE: The transmission fluid pan gasket can be reused if not damaged.
NOTE: Align the transmission fluid pan gasket tabs in the correct locations.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 8 of 10
5. NOTE: Install the bolts and studbolts in the correct locations noted during removal.
Install the transmission fluid pan and loosely install the bolts and studbolts.
1. Tighten the studbolts in a crisscross pattern.
Torque: 106 lb.in (12 Nm)
2. Tighten the bolts in a crisscross pattern.
Torque: 89 lb.in (10 Nm)
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 9 of 10
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 10 of 10
Refer to: Transmission Fluid Drain and Refill (307-01 Automatic Transmission - 10-Speed Automatic
Transmission - 10R80, General Procedures).
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019