Professional Documents
Culture Documents
Gm-A2hr Á ®TDX
Gm-A2hr Á ®TDX
Gm-A2hr Á ®TDX
WIRING
1 - Connect to System Line (L2), (L1) or (L3)
4 - External Meter (FS 1mA), separated from alarm circuit
5 - External reset T.B : Device reset
6 - Protective earth (connect to equipment ground) DISPLAY & CONTROL
11 - Alarm output (DPDT) 2 - Power LED light 3 - Alarm LED light
12 - Remote function control as below (use if necessary) 14 - Reset Button : Device reset
C - T1 : Self test mode, meter will indicate zero 7 - Alarm set selector (16steps - digital)
C - T2 : Fault finding mode, use to find grounding points 8 - DC fault LED light
13 - Auxiliary Supply voltage 9 - Meter zero adjust with VR at test mode
A1-A2 : External supply voltage AC110 / 220V 50/60Hz 10 - Mode selector as below
A1-A3 : External supply voltage AC440V 50/60Hz
TEST mode : Self test mode, meter will indicate zero(0)
500uF mode : Measuring at VFD, BWTS(Ce=up to 500uF) runing
1,000uF mode : Measuring at VFD, BWTS
(Ce=up to 1,000uF) running.
FAULT FINDING mode : Use to find grounding points
Note : Ce means leakage capacitance between cable and hull.
Design and specifications can be change for quility improvement without notice. Ask factory for the current technical specifications before purchase and / or use.
If any problems caused by this product, please be sure to contact us immediately. www.bmtk.co.kr / E-mail bmtk@bmtk.co.kr Mar. 2019.
8
GROUND FAULT MONITOR GM-A2HR
VFD & BWTS SYSTEM LINE WIRING APPLICATION
Design and specifications can be change for quility improvement without notice. Ask factory for the current technical specifications before purchase and / or use.
If any problems caused by this product, please be sure to contact us immediately. www.bmtk.co.kr / E-mail bmtk@bmtk.co.kr Mar. 2019.
9
GROUND FAULT MONITOR GM-A2HR
VFD & BWTS SYSTEM LINE FUNCTION DESCRIPTION
표준 결선도
비접지 교류통전선로
접지상(Phase)표시등 시험
상 접지 램프 테스트는 접지된 위상을 확인
하는 기능으로 IRM과 독립적입니다.
주의
오류찾기, 자체 TEST
후에는 원래위치
(500-1,000uF)에
Self-grounding test & Meter "0" set SET 하십시오.
MODE SELECTOR를 TEST로 설정하면, 외부접지 단자(E)가
차단되고 내부 접지저항이 "0"으로 전환 연결되며 500uF mode
METER는 즉시 "0"을 표시하고 경보가 발생됩니다. VFD, BWTS 가동시 외부에서 혼입된 다양한 외란 요인
이 때 VR로 미터 "0"점을 조정할 수 있습니다. (직류 서지, 고주파, 누설 정전 용량 등)을 제거하고 순수한 절연
저항을 측정하기 위해 특별한 동작을 수행합니다.
Reset : Button or T.B (K1,K2)
1,000uF mode
EL TEST를 할 때 Device를 Reset 시켜줍니다.
용량이 큰 BWTS 가동시 누설 정전용량 및 Surge가 커지므로
이때 사용합니다.
Fault finding mode
500uF, 1,000uF 모드에서는 외란 요인의 상태에 따라 많은 시간이
오류 찾기 모드는 접지된 위치를 찾는데 사용되며,
소요되며 순수한 절연 저항값만이 내부 처리 과정을 통해 측정
VFD, BWTS 모드에서는 응답시간이 길어지므로
되고 표시되며 측정시간은 수십초~수십분입니다.
응답시간이 빠른 오류 찾기 모드를 사용합니다.
그러나 VFD, BWTS 운전 중에는 적용되지 않습니다. Remote & Meter connection
오류찾기 모드는 측정을 빨리 하기 위해 외란 요인을 제거하지 원격 모드에서는 외부 도어나 콘솔에서 원격으로 기능을 수행할
않기 때문에 측정에 오류를 일으킬 수 있습니다. 수 있습니다. Meter(M+,M-) 출력은 정전류 출력이므로 2~3개
VFD, BWTS가 운전중 일때는 오류찾기 모드를 사용하지 마십시오. 의 Meter를 직렬로 연결해도 지시 값은 동일합니다.
Design and specifications can be change for quility improvement without notice. Ask factory for the current technical specifications before purchase and / or use.
If any problems caused by this product, please be sure to contact us immediately. www.bmtk.co.kr / E-mail bmtk@bmtk.co.kr May. 2019.
10
GROUND FAULT MONITOR GM-A2HR
VFD & BWTS SYSTEM LINE FUNCTION DESCRIPTION
STANDARD CONNECTION
DISTURBANCE FACTOR
SUPERIMPOSED Un-grounded AC line
Caution
Please set to
orginal setting
500-1,000uF
after done fault
finding or self test.
Design and specifications can be change for quility improvement without notice. Ask factory for the current technical specifications before purchase and / or use.
If any problems caused by this product, please be sure to contact us immediately. www.bmtk.co.kr / E-mail bmtk@bmtk.co.kr May. 2019.
6
GROUND FAULT MONITOR METER SCALES &
EXTERNAL METER PANEL CUTTING SIZE
TYPE : DCF12Na
OPTION
120 x 110
Design and specifications can be change for quility improvement without notice. Ask factory for the current technical specifications before purchase and / or use.
If any problems caused by this product, please be sure to contact us immediately. www.bmtk.co.kr / E-mail bmtk@bmtk.co.kr Mar. 2019.