Company Name:
ETHIOPIAN ELECTRIC UTILITY
Document NO.
EEU/EQ/TS-PG-257
Title:-Technical Specification of Bolted Parallel Grove Clamps
Issue No.1 | Page 1 of 8
EEU
TECHNICAL SPECIFICATION
Of
BOLTED PARALLEL GROVE
| Prepared by
Abebaw Belay
Elias Azene ay i
Sign | Checked by | Sign
Rev.No. | Date Page
Zi May 7, 2023 | No.1‘Company Name: Document NO.
ETHIOPIAN ELECTRIC UTILITY Ene,
Title:-Technical Specification of Bolted Parallel Grove Clamps Issue No.1 | Page 2 of 8
Table of Contents
BOLTED PARALLEL GROOVE CLAMPS 3
1. SCOPE. 3)
as SYSTEM PARAMETERS & SERVICE CONDITIONS 3
3. REFERENCE STANDARDS 3
4 BOLTED PARALLEL GROOVE CLAMPS 4
5. MARKING 5
6. INSPECTION AND TESTING 5
Type Tests5
f QUALITY ASSURANCE PLAN 6
8. GURANTEED TECHNICAL PARTICULARS FOR
PARALLEL GROVE CLAMPS AL/AL (25....240MM2) 2
Prepared — by | Sign | Checked by | Sign Rev.No. | Date Page
Abebaw Belay 1 No.2
Elias Azene
PS
May 7, 2023@
| Company Name: Document Ni
ETHIOPIAN ELECTRIC UTILITY —
:-Technical Specification of Bolted Parallel Grove Clamps [Issue No.1 [Page 3 of 8
ie
This specification covers the Design, Manufacture, Testing and delivery of Bolted parallel!
BOLTED PARALLEL GROOVE CLAMPS
SCOPE
grove clamps for medium voltage installation.
2 SYSTEM PARAMETERS & SERVICE CONDITIONS
Item Parameter
Altitude Altitude up to 3000m
Annual Rainfall 1250mm
Period of exceptional | June to September
Rains
‘Ambient Air
‘Temperatures:
Average 430%
Minimum 5%
‘Maximum 50%
Relative Air Humidity 70%
Wind Velocity:
Maximum — wind(height
above ground level) | 35mv/s
0-30m 45m/s
30-
50m
Isoceraunie Level Upto 100 thunderstorm days/year
Seismic Level No records of any activity
5 REFERENCE STANDARDS
The materials supplied shall conform to the latest edition of the appropriate IEC/BSEN
standards and/or other recognized international standards.
In the event of direct conflict between various order documents, the precedence of
authority of documents shall be as follows —
Prepared by
Abebaw Belay
Sign | Checked by
Elias Azene
Rev.No. | Date
1 May 7, 2023
Page
No. 3Company Name: Document NO.
ETHIOPIAN ELECTRIC UTILITY See oan
‘echnical Specification of Bolted Parallel Grove Clamps Issue No. 1 Page 4 of 8
4.
1. Guaranteed Technical Particulars (GTP)
IL. Specification including applicable codes & standards
IIL. Approved Vendor Drawings
IV. Other documents
S BOLTED PARALLEL GROOVE CLAMPS
Conductor connectors are required for jumpers, spur take-off, and drop connections to
Fuse cut outs for AAAC non-tension connections. IEC612380r other national ot
international Standards which ensure equal or higher quality shall be applicable
‘The edges of the connector barrels shall be rounded to assist stress relief when the
connectors are used with covered (partially insulated) conductors.
Alll connectors shall be supplied pre-filled with high quality oxide inhibiting compound
and shall be protectively capped to prevent spillage or spoilage of this compound. All
connectors shall be clearly and permanently marked with the correct conductor size
range and category.
‘The clamps shall be made of corrosion-resistant alloy with a minimum tensile strength
400 MPa. The resistance of all clamps shall not be more than 50% of the resistance of the
conductor itself over the same length as the clamp.
a) The connectors shall:
(i) Have serrated conductor groves,
(ii) Interlocking fingers,
(iii) Be recessed to prevent bolt head turning during tightening,
(iv) Have a one, two, or three bolt pattern to suit conductor size and current rating,
(¥) Have bolts of sufficient length to allow installation without disassembling the
connector,
(vi) Have conductor entries of a generous radius to prevent damage to strands, and
(vii) Be pre-filled with joint compound,
‘The Bidder shall submit type test certificates with the bid to demonstrate
compliance with the requirements of this specification.
b) Types
Prepared by
Abebaw Belay
Sign | Checked by}
Elias Azene| ( z(
Rev.No. | Date
i May 7, 2023
Page |
No.4Company Name:
Document NO.
ETHIOPIAN ELECTRIC UTILITY ee
Technical Specification of Bolted Parallel Grove Clamps Issue No. 1 Page 5 of 8
Clamp shall be supplied for the following type of conductors:
Side A Side B
Nominal Size [Material to be | Nominal Size | Material to be
mm? connected mm? connected _|
240 AAAC 240 AAAC
150 AAAG 150 AAAC
100 AAAC 100 AAAC
350 AAAC 50 AAAC |
25 AAAC 25 AAAC
Se MARKING
Each connector shall be legibly marked with the manufacturer’s catalogue number and
conductor diameter range for each grove, and each shall be supplied in a clear plastic
package.
Packaging
Each connector shall be supplied in an individual sealed clear plastic bag or pocket. The
bag shall be adequately durable to ensure no grease or oxide inhibiting compound is lost
ot spoiled prior to the time of installation, The bag shall be labelled with the makers
name or trade mark, and the size range of the fitting, Bags shall be further packaged in
cardboard or similar containers in quantities of approximately 100 fittings of the identical
description.
The successful bidder shall get approval from the client for its specifications and
drawings before proceed to the mass production,
6. INSPECTION AND TESTING
TYPE TESTS
‘Test shall be performed according to IEC requirements and it should comprise of the
following tests:
a) — Mechanical tests
b) Resistance tests.
c) Abrasion test
d) Electrical test
Prepared by Sign | Checked by
Rev.No. | Date Page
Abebaw Belay Elias Azene
1 May 7, 2023 | No.5Company Name: Document NO.
& ETHIOPIAN ELECTRIC UTILITY ed
[ Title:-Technical Specification of Bolted Parallel Grove Clamps Issue No. 1 Page 6 of 8
a QUALITY ASSURANCE PLAN
A Quality Assurance Plan (QA Plan) including customer hold points covering the
manufacturing activities of the material shall be required to be submitted by the Bidder
with the tender.
The contractor shall follow the approved Quality Assurance Plan. If desired by the
Purchaser, he shall give access to all the documents and materials to satisfy the purchaser
that the Quality Assurance Plan is being properly followed.
aN
i ys
Prepared by Sign | Checked by Appreeed hy Rev.No. | Date Page
Abebaw Belay Elias Azene Tefera Derbe, 1 May 7, 2023 | No. 6o
‘Company Name:
ETHIOPIAN ELECTRIC UTILITY
Document NO.
EEU/EQ/TS-PG-257
Title:-Technical Specification of Bolted Parallel Grove Clamps Issue No, 1 Page 7 of 8
8. GURANTEED TECHNICAL PARTICULARS FOR
PARALLEL GROVE CLAMPS AL/AL
(25....240MM2)
No | Item Unit | Requirement | Bid Offer
1 Manufacturer
2 | Country of origin
3_| Type Designation
4 [ Range of main conductor eross-section | mm2 | Al
25...240mm2
5 | Range of branch conductor cross-|mm2 | Al
section 25...240mm2
6 | Range of main conductor diameter | Mm
7 __| Range of branch conductor diameter | Mm
8 | Material of main conductor ‘Aluminum
alloy
[9 | Material of branch conductor ‘Aluminum
alloy
10 | Material standard
11 __| Tensile strength of the body Némm2_ | 300
12___| Strength class of bolts and nuts
13__| Thread size of bolts and nuts Mio
14 | Tightening torque of bolts zal
15 | Thickness of zine coating Micro | 85
meter
16 __| Net weight per piece 2
[17 | Standard package size pes
Prepared by | Sign | Checked by Rev.No. | Date Page
Abebaw Belay Elias Azene 1 May 7, 2023. | No.7‘Company Name:
ETHIOPIAN ELECTRIC UTILITY
Document NO.
EEU/EQ/TS-PG-257
Title:-Technical Specification of Bolted Parallel Grove Clamps Issue No. 1 Page 8 of 8
Drawing of Bolted Parallel Groove
rts
Prepared by —_| Sign | Checked by] Sign | App Rev.No. | Date Page
Abebaw Belay wi Elias Azene ee Tefera Derbe 1 May 7, 2023 | No.8
+2008 23NM AL25—248
2 co-r9
Notes
1, Sulteble for AL 25-240 mm2/AL, 25~-240mm2 conductors
2. Recommended torque of the boit: 23 Nm
3, Logo, "AL25~240°", "2008", “23m” shall be marked on upper body,
“AL 6.3-12.5@ shall be morked on the lower body, according to DIN 48215,
| 4 All ferrous parts are hot dip galvanized according to BS 729
5. All dimensions in millimeters
2 [6 | Spring Washer Gaivenized Steel
2 [5 | Hex nut (Galvanized Steel
2 [4 | Hex Bolt Galvanized Steel
1 | 3 | Pressure Pos ‘Auminiury Alloy
1 | 2 | tower Body [Aluminium Alloy
1 [1 | Upper Boay ‘Aluminior Alloy
ayy [lie Description Cat-no Drawing no. Remarks
Engineting & Oval
Parallel Groove Clamp AL 25-240 / AL 25-240
sau DRT Fer
EEU
Pa paar a Pay 26200