Professional Documents
Culture Documents
DRI1124C
DRI1124C
Setup Guide
Contents
How to read this manual
The instructions in this manual use the indications below.
! Button names displayed on the main unit of the product, and the screen names
on the software are enclosed in [ ]. (Example: [LINK] button, [UTILITY] screen)
! The version of rekordbox for mobile devices is referred to as “rekordbox (iOS/
Android) ”.
! The version of rekordbox for Mac/Windows is referred to as “rekordbox (Mac/
Windows)”. “rekordbox” is used to indicate the versions of rekordbox and rekord-
box (iOS/Android) simultaneously, as well as when referring to rekordbox func-
tions directly.
Before start
Purpose of this guide........................................................................................................3
General description of PRO DJ LINK...............................................................................3
To make connections........................................................................................................4
About trademarks and registered trademarks...............................................................4
2 En
Before start
Before start
Purpose of this guide
This guide describes the procedures for making the connections required to use the PRO DJ LINK functions.
Mobile device (iOS/Android) that can be connected to each type of equipment with USB cable
For mobile devices (iOS/Android) that can be connected by USB cable, see the operating instructions of each type of equipment.
En 3
To make connections
The connection procedure for using the PRO DJ LINK function differs according to the combination of devices you are using.
This manual describes the connection procedures for different combinations of PRO DJ LINK-compatible Pioneer DJ players and DJ mixers.
First check the combination of devices you are using on the table below, then connect following the description of the relevant page.
! Ex.: If you are using a CDJ-2000NXS and a DJM-2000NXS, you should follow procedure 1 . Proceed to page 1 .
DJ player (Group A)
CDJ-2000NXS/CDJ-900NXS/XDJ-1000
DJ player (Group B)
CDJ-2000/CDJ-900
DJ mixer (Group A)
DJM-2000NXS/DJM-2000
DJ mixer (Group B)
DJM-900NXS/DJM-900SRT
DJ mixer (Group A) DJ mixer (Group B) Other DJ mixers
DJ player (Group A)
1 2 3
DJ player (Group B)
4 5 6
Connecting by wireless LAN
! Use the wireless router (available in the market) and access point (available in the market) which can obtain a sufficient communication speed such as IEEE802.11n,
IEEE802.11g etc. Depending on the signal conditions in the usage environment or the wireless router and access point, PRO DJ LINK connections may not operate
properly.
! For connection method of wireless LAN, see the operating instructions of the computer or wireless LAN equipment used.
4 En
Connecting DJ player (Group A) and DJ
1
mixer (Group A)
Equipment used
! CDJ-2000NXS/CDJ-900NXS/XDJ-1000 (1 to 4)
! Wireless router with internal switching hub or access point
! Mobile device (iOS/Android) or computer (Mac/Windows) on which rekordbox is installed
! DJM-2000NXS or DJM-2000
! Audio cable
! LAN cables (one for each DJ player + one more)
OFF
POWER ON
MIC MASTER
CD CD CH CD CD
/DIGITAL PHONO USB 1/2 /DIGITAL LINE USB 3/4 1 2 3 4 SELECT
MIC A B M /DIGITAL LINE USB 5/6 /DIGITAL PHONO USB 7/8
MIC +9 10 +9 10 10 +9 10 +9 10
ECHO REVERB SLIP FILTER PHASER SEND/
LEVEL HI 7 HI 7
ROLL RETURN
7 HI 7 HI 7
- 0 EFFECT FREQUENCY 4
4 4 4 4
2 2 LOW MID HI 2 2 2
HI
1 1 1 1 1
EQ -12 +12 -26/ +6 -26/ +6 -26/ +6 -26/ +6
0 0 0 0 0
-12 +12 -2 -2 -2 -2 -2
MIN MAX MIN MAX MIN MAX
TALK EQ/ -3 EQ/ -3 -3 EQ/ -3 EQ/ -3
OFF ON OVER ISO ISO ISO ISO
-5 -5 -5 -5 -5
-26/ +6 -7 -26/ +6 -7 1/8 1/4 1/2 3/4 1/1 2/1 4/1 -7 -26/ +6 -7 -26/ +6 -7
- 10 - 10 - 10 - 10 - 10
INST FX LOW LOW LOW LOW
- 15 - 15 - 15 - 15 - 15
CRUSH LPF
CUE
LIVE
CUE CUE SAMPLER CUE CUE CUE
MIN MAX
SYNC MASTER
LINK MONO STEREO
UTILITY
CUE WAKE UP
10 10
HEADPHONES 9 9
BOOTH MONITOR
Audio cable
MONO SPLIT STEREO 8 8
MIX
7 7
6 6
5 5
4 4 0
MIXING
3
REMIX
3 MIDI
2 2 ON /OFF START/STOP
1 1
0 0
SNAPSHOT
CUE MASTER
PHONES
Wireless
CROSS FADER
A B
PROFESSIONAL MIXER
DJM-2000 nexus
Connection procedure
1 Remove the LAN cable from the equipment and unplug the mobile device (iOS/Android) and storage device (USB/SD) from
the DJ player.
! When mobile device (iOS/Android) or storage device (USB/SD) are set, and when LINK connection is established, [PLAYER No.] settings cannot be changed.
En 5
Connecting the cables (LAN cable and audio cables)
CONTROL
CD DIGITAL
POWER
L L CH
L 3 CH 1 COMPUTER
L 1 POWER
CONTROL DIGITAL CONTROL
CONTROL OUT CH4 CH3 IN CH2 CH1 CONTROL
OFF POWER CD DIGITAL CD DIGITAL O) CD DIGITAL CD DIGITAL
ON
R R R R
MASTER1 MASTER2 REC OUT BOOTH SEND
LINK
RETURN CH 3 CH 1 COMPUTER 1
R L L TRS MIDI OUT USB
MASTER R L R L(MONO) R L(MONO)
AC IN ATT.
LINK
-6dB -3dB 0dB
CH 4 CH 2 COMPUTER 2
R
1GND 2HOT CH 4 CH 2 COMPUTER 2
3COLD
Check that the player number indicated on the DJ player’s screen is lit in white.
Connecting to LINK Cannot connect to LINK
! In case the player No. lights up gray, LINK connection is not established. When there is a DJ player that is lighted up in gray, redo the connection procedure once again.
! Similarly, check the other DJ players.
Checking that the LAN cable and audio cables are synchronized
Load a music file, then operate the DJ players that are connected by link to play and pause the track repeatedly.
Check that the player number displayed on the DJ player’s screen is the same as the channel number that lights on the DJ mixer’s channel level indicator.
If it does not match, the connection is considered to be incorrect. Redo the connection procedure once again.
TRIM TRIM
OVER OVER
+9 10 +9 10
HI 7 HI 7
4 4
2 2
1 1
-26/ +6 -26/ +6
0 0
MID -1 MID -1
-2 -2
EQ/ -3 EQ/ -3
ISO ISO
-5 -5
-26/ +6 -7 -26/ +6 -7
- 10 - 10
LOW LOW
- 15 - 15
-24 -24
dB dB
CDJ-2000NXS DJM-2000NXS
! Similarly, check the other DJ players.
6 En
Checking the device(s) connected by wireless connection
1 Connect the computer or mobile device (iOS/Android) to wireless router or access points with wireless LAN.
2 Press the [rekordbox] button.
TAG TRACK
LINK
USB
SD
DISC
AUTO CUE
3 Tap the [LOAD] icon, or click the [LINK] button to establish the link connection.
The devices that have been recognized are indicated on the DJ player’s screen.
En 7
1-2
Connecting rekordbox via cable/Setting the mobile device (iOS/Android) or storage
device (USB/SD)
Equipment used
! CDJ-2000NXS/CDJ-900NXS/XDJ-1000 (1 to 4)
! USB cable for connecting mobile device (Use the included iPod cable to connect the iPod to the CDJ-2000NXS.)
! Mobile device (iOS/Android) or computer (Mac/Windows) on which rekordbox is installed
! Storage device (USB/SD) on which the music files analyzed by rekordbox are stored.
! DJM-2000NXS or DJM-2000
! Audio cable
! LAN cables (one for each DJ player + one more)
OFF
POWER ON
MIC MASTER
CD CD CH CD CD
/DIGITAL PHONO USB 1/2 /DIGITAL LINE USB 3/4 1 2 3 4 SELECT
MIC A B M /DIGITAL LINE USB 5/6 /DIGITAL PHONO USB 7/8
MIC +9 10 +9 10 10 +9 10 +9 10
ECHO REVERB SLIP FILTER PHASER SEND/
LEVEL HI 7 HI 7
ROLL RETURN
7 HI 7 HI 7
- 0 EFFECT FREQUENCY 4
4 4 4 4
2 2 LOW MID HI 2 2 2
HI
1 1 1 1 1
EQ -12 +12 -26/ +6 -26/ +6 -26/ +6 -26/ +6
0 0 0 0 0
-12 +12 -2 -2 -2 -2 -2
MIN MAX MIN MAX MIN MAX
TALK EQ/ -3 EQ/ -3 -3 EQ/ -3 EQ/ -3
OFF ON OVER ISO ISO ISO ISO
-5 -5 -5 -5 -5
-26/ +6 -7 -26/ +6 -7 1/8 1/4 1/2 3/4 1/1 2/1 4/1 -7 -26/ +6 -7 -26/ +6 -7
- 10 - 10 - 10 - 10 - 10
INST FX LOW LOW LOW LOW
- 15 - 15 - 15 - 15 - 15
CRUSH LPF
CUE
LIVE
CUE CUE SAMPLER CUE CUE CUE
MIN MAX
SYNC MASTER
LINK MONO STEREO
UTILITY
CUE WAKE UP
10 10
HEADPHONES 9 9
BOOTH MONITOR
MONO SPLIT STEREO
Audio cable
8 8
MIX
7 7
6 6
5 5
4 4 0
MIXING
3
REMIX
3 MIDI
2 2 ON /OFF START/STOP
1 1
0 0
SNAPSHOT
CUE MASTER
PHONES
USB connections
CROSS FADER
A B
PROFESSIONAL MIXER
DJM-2000 nexus
Connection procedure
1 Remove the LAN cable from the equipment and unplug the mobile device (iOS/Android) and storage device (USB/SD) from
the DJ player.
! When mobile device (iOS/Android) or storage device (USB/SD) are set, and when LINK connection is established, [PLAYER No.] settings cannot be changed.
8 En
Connecting the cables (LAN cable and audio cables)
CONTROL
CD DIGITAL
POWER
L L CH
L 3 CH 1 COMPUTER
L 1 POWER
CONTROL DIGITAL CONTROL
CONTROL OUT CH4 CH3 IN CH2 CH1 CONTROL
OFF POWER CD DIGITAL CD DIGITAL O) CD DIGITAL CD DIGITAL
ON
R R R R
MASTER1 MASTER2 REC OUT BOOTH SEND
LINK
RETURN CH 3 CH 1 COMPUTER 1
R L L TRS MIDI OUT USB
MASTER R L R L(MONO) R L(MONO)
AC IN ATT.
LINK
-6dB -3dB 0dB
CH 4 CH 2 COMPUTER 2
R
1GND 2HOT CH 4 CH 2 COMPUTER 2
3COLD
Check that the player number indicated on the DJ player’s screen is lit in white.
Connecting to LINK Cannot connect to LINK
! In case the player No. lights up gray, LINK connection is not established. When there is a DJ player that is lighted up in gray, redo the connection procedure once again.
! Similarly, check the other DJ players.
Checking that the LAN cable and audio cables are synchronized
Load a music file, then operate the DJ players that are connected by link to play and pause the track repeatedly.
Check that the player number displayed on the DJ player’s screen is the same as the channel number that lights on the DJ mixer’s channel level indicator.
If it does not match, the connection is considered to be incorrect. Redo the connection procedure once again.
TRIM TRIM
OVER OVER
+9 10 +9 10
HI 7 HI 7
4 4
2 2
1 1
-26/ +6 -26/ +6
0 0
MID -1 MID -1
-2 -2
EQ/ -3 EQ/ -3
ISO ISO
-5 -5
-26/ +6 -7 -26/ +6 -7
- 10 - 10
LOW LOW
- 15 - 15
-24 -24
dB dB
CDJ-2000NXS DJM-2000NXS
! Similarly, check the other DJ players.
En 9
Checking the connected device(s)
1 Press one of the medium select buttons to check the connection with the respective device.
— To use a computer (Mac/Windows) connected by wired LAN: Press the [rekordbox] button.
— When a storage device (USB/SD) set to other players where LINK is connected is to be used: Press the [LINK] button.
— To use a mobile device (iOS/Android) or USB device connected by wire to the USB (A terminal): Press the [USB] button.
— To use an SD memory card: Press the [SD] button.
! The following describes examples for when the [rekordbox] button is pressed and when the [USB] button is pressed.
LINK
USB
SD
DISC
AUTO CUE
! To use a mobile device (iOS/Android) connected by wire: Press the [USB] button.
3 Tap the [LOAD] icon, or click the [LINK] button to establish the link connection.
10 En
Connecting DJ player (Group A) and DJ
2
mixer (Group B)
Equipment used
! CDJ-2000NXS/CDJ-900NXS/XDJ-1000 (1 to 4)
! Wireless router with internal switching hub
! Mobile device (iOS/Android) or computer (Mac/Windows) on which rekordbox is installed
! DJM-900NXS or DJM-900SRT
! Audio cable
! LAN cables (one for each DJ player + one more)
POWER
BEAT EFFECTS
0
TRIM TRIM TRIM TRIM
1 2 3 4
10 10 10 10 10
MIC 1 MIC A B MS T
7 9 7 9 7 9 7 9 7 PARAMETER
2 2 2 2 2 %
MIC 2 ms
1 1 1 1 1
0
0 0 0 0 0
-26 / 6 -26 / 6 -26 / 6 -26 / 6
-1 -1 -1 -1 -1
HI MID MID MID MID
-2 -2 -2 -2 -2 X- PAD
12 12 EQ
-3 EQ/ -3 EQ/ -3 EQ/ -3 EQ/ -3
ISO ISO ISO ISO
LOW -5 -5 -5 -5 -5
dB
-26 /
dB
-26 /
dB
-26 /
dB
-26 / L dB R AUTO QUAN-
6 6 6 6
/ TAP TAP TIZE
FLANGER PHASER
LINK CUE CUE CUE CUE CUE
FILTER ROBOT
TRANS MELODIC
REVERB SLIP ROLL
CUE
SPIRAL ROLL
MONO STEREO ECHO REV ROLL
FADER START DELAY MIDI LFO
SND/ RTN
1 2 3 4 4 MIC
3 CF.A
10 10 10
2 CF.B
HEADPHONES 9 9 9 BOOTH MONITOR
1 MASTER
8 8 8
MONO SPLIT STEREO
Audio cable
7 7 7
6 6 6
5 5 5 TIME
4 4 4
MIXING 0
3 3 3
2 2 2
1 1 1
EQ CURVE
ISOLATOR EQ
0 0 0
CUE MASTER
LEVEL LEVEL / DEPTH
0 MIN MAX
PHONES
Wireless
A B
Connection procedure
1 Remove the LAN cable from the equipment and unplug the mobile device (iOS/Android) and storage device (USB/SD) from
the DJ player.
! When mobile device (iOS/Android) or storage device (USB/SD) are set, and when LINK connection is established, [PLAYER No.] settings cannot be changed.
En 11
Connecting the cables (LAN cable and audio cables)
CH 3 CH 2
LINE CD/ LINE LINE CD/ LINE
L L
CH 4 CH 3 CH 2 CH 1
PHONO CD/ LINE LINE CD/ LINE LINE CD/ LINE PHONO CD/ LINE
L L L L
POWER RETURN POWER
R L (MONO) MIC2 MIDI OUT
CONTROL OFF POWER GND SIGN CONTROL
ON SIGNAL GND SIGNAL GND
R R R R
MASTER1 R MASTER2 REC OUT BOOTH R DIGITAL
R L R
SEND
L (MONO)
R L L
MASTER2 REC OUT
L
R
TRS
L BOOTH
LINK MASTER
CH2 CH1
R L
OUT
IN
L L L TRS
L R
R R L RR
AC IN 2 HOT
CH4 CH3
1 GND
3 COLD
Check that the player number indicated on the DJ player’s screen is lit in white.
Connecting to LINK Cannot connect to LINK
! In case the player No. lights up gray, LINK connection is not established. When there is a DJ player that is lighted up in gray, redo the connection procedure once again.
! Similarly, check the other DJ players.
Checking that the LAN cable and audio cables are synchronized
Load a music file, then operate the DJ players that are connected by link to play and pause the track repeatedly.
Check that the player number displayed on the DJ player’s screen is the same as the channel number that lights on the DJ mixer’s channel level indicator.
If it does not match, the connection is considered to be incorrect. Redo the connection procedure once again.
TRIM TRIM
OVER OVER
10 10
7 9 7 9
4 HI 4 HI
2 2
1 1
0 0
-26 / 6 -26 / 6
-1 -1
MID MID
-2 -2
-3 EQ/ -3 EQ/
ISO ISO
-5 -5
- 7 -26 / 6 - 7 -26 / 6
-10
LOW -10
LOW
-15 -15
-24 -24
CDJ-2000NXS DJM-900NXS
! Similarly, check the other DJ players.
12 En
Checking the device(s) connected by wireless connection
1 Connect the computer or mobile device (iOS/Android) to wireless router or access points with wireless LAN.
2 Press the [rekordbox] button.
TAG TRACK
LINK INFO UTILITY BACK / REMOVE
LINK
SD
DISC
AUTO CUE
3 Tap the [LOAD] icon, or click the [LINK] button to establish the link connection.
The devices that have been recognized are indicated on the DJ player’s screen.
En 13
2-2
Connecting rekordbox via cable/Setting the mobile device (iOS/Android) or storage
device (USB/SD)
Equipment used
! CDJ-2000NXS/CDJ-900NXS/XDJ-1000 (1 to 4)
! Switching hub
! USB cable for connecting mobile device (Use the included iPod cable to connect the iPod to the CDJ-2000NXS.)
! Mobile device (iOS/Android) or computer (Mac/Windows) on which rekordbox is installed
! Storage device (USB/SD) on which the music files analyzed by rekordbox are stored.
! DJM-900NXS or DJM-900SRT
! Audio cable
! LAN cables (one for each DJ player + two more)
POWER
BEAT EFFECTS
0
TRIM TRIM TRIM TRIM
1 2 3 4
10 10 10 10 10
MIC 1 MIC A B MS T
7 9 7 9 7 9 7 9 7 PARAMETER
2 2 2 2 2 %
MIC 2 ms
1 1 1 1 1
0
0 0 0 0 0
-26 / 6 -26 / 6 -26 / 6 -26 / 6
-1 -1 -1 -1 -1
HI MID MID MID MID
-2 -2 -2 -2 -2 X- PAD
12 12 EQ
-3 EQ/ -3 EQ/ -3 EQ/ -3 EQ/ -3
ISO ISO ISO ISO
LOW -5 -5 -5 -5 -5
dB
-26 /
dB
-26 /
dB
-26 /
dB
-26 / L dB R AUTO QUAN-
6 6 6 6
/ TAP TAP TIZE
FLANGER PHASER
LINK CUE CUE CUE CUE CUE
FILTER ROBOT
TRANS MELODIC
REVERB SLIP ROLL
CUE
SPIRAL ROLL
MONO STEREO ECHO REV ROLL
FADER START DELAY MIDI LFO
SND/ RTN
1 2 3 4 4 MIC
3 CF.A
10 10 10
2 CF.B
HEADPHONES 9 9 9 BOOTH MONITOR
1 MASTER
8 8 8
Audio cable
MONO SPLIT STEREO
7 7 7
6 6 6
5 5 5 TIME
4 4 4
MIXING 0
3 3 3
2 2 2
1 1 1
EQ CURVE
ISOLATOR EQ
0 0 0
CUE MASTER
LEVEL / DEPTH
0 MIN MAX
PHONES
A B
USB connections
Connection procedure
1 Remove the LAN cable from the equipment and unplug the mobile device (iOS/Android) and storage device (USB/SD) from
the DJ player.
! When mobile device (iOS/Android) or storage device (USB/SD) are set, and when LINK connection is established, [PLAYER No.] settings cannot be changed.
14 En
Connecting the cables (LAN cable and audio cables)
R R R R
MASTER1 R MASTER2 REC OUT BOOTH R DIGITAL
R L R
SEND
L (MONO)
R L L
MASTER2 REC OUT
L
R
TRS
L BOOTH
LINK MASTER
CH2 CH1
R L
OUT
IN
L L L TRS
L R
R R L RR
AC IN 2 HOT
CH4 CH3
1 GND
3 COLD
Check that the player number indicated on the DJ player’s screen is lit in white.
Connecting to LINK Cannot connect to LINK
! In case the player No. lights up gray, LINK connection is not established. When there is a DJ player that is lighted up in gray, redo the connection procedure once again.
! Similarly, check the other DJ players.
Checking that the LAN cable and audio cables are synchronized
Load a music file, then operate the DJ players that are connected by link to play and pause the track repeatedly.
Check that the player number displayed on the DJ player’s screen is the same as the channel number that lights on the DJ mixer’s channel level indicator.
If it does not match, the connection is considered to be incorrect. Redo the connection procedure once again.
TRIM TRIM
OVER OVER
10 10
7 9 7 9
4 HI 4 HI
2 2
1 1
0 0
-26 / 6 -26 / 6
-1 -1
MID MID
-2 -2
-3 EQ/ -3 EQ/
ISO ISO
-5 -5
- 7 -26 / 6 - 7 -26 / 6
-10
LOW -10
LOW
-15 -15
-24 -24
CDJ-2000NXS DJM-900NXS
! Similarly, check the other DJ players.
En 15
Checking the connected device(s)
1 Press one of the medium select buttons to check the connection with the respective device.
— To use a computer (Mac/Windows) connected by wired LAN: Press the [rekordbox] button.
— When a storage device (USB/SD) set to other players where LINK is connected is to be used: Press the [LINK] button.
— To use a mobile device (iOS/Android) or USB device connected by wire to the USB (A terminal): Press the [USB] button.
— To use an SD memory card: Press the [SD] button.
! The following describes examples for when the [rekordbox] button is pressed and when the [USB] button is pressed.
LINK
USB
SD
DISC
AUTO CUE
! To use a mobile device (iOS/Android) connected by wire: Press the [USB] button.
3 Tap the [LOAD] icon, or click the [LINK] button to establish the link connection.
16 En
Connecting DJ player (Group A) and
3
other DJ mixers
3-1
Connecting rekordbox by wireless LAN
POWER
WAKE UP
OVER
10 10 10 10 10
9 9 9 9
7 7 7 7 7
MIC 1 HI HI HI HI CH SELECT
4 4 4 4 4 1 2 3 4
0 LEVEL
2 2 2 2 2
MIC A B MST
PARAMETER
MIC 2 1 1 1 1 1 AUTO
TAP BPM
0 0 -26 / 6 0 -26 / 6 0 -26 / 6 0 -26 / 6 0 %
ms
-1 MID -1 MID -1 MID -1 MID -1
HI -2 -2 -2 -2 -2
EQ/ EQ/ EQ/ EQ/
-3 ISO -3 ISO -3 ISO -3 ISO -3
12 12 EQ
DJM-2000NXS/
-24 -24 -24 -24 -24
AUTO
dB -26 / 6 dB -26 / 6 dB -26 / 6 dB -26 / 6 L dB R / TAP TAP
BEAT BEAT BEAT BEAT
COLOR COLOR COLOR COLOR BALANCE
NOISE CUTTER
DJM-2000/
SOUND COLOR FX CUE
CRUSH FILTER L R
LOW HI LOW HI LOW HI LOW HI
FILTER FLANGER
DJM-900NXS/
TRANS PHASER
CUE CUE CUE CUE CUE
FADER START REVERB ROBOT
SPIRAL SLIP ROLL
1 2 3 4 PITCH ECHO ROLL
MONO STEREO ECHO REV ROLL
DELAY SND/ RTN
DJM-900SRT
4 MIC
Audio cable
10 10 10 3 CF.A
HEAD PHONES 9 9 9
BOOTH MONITOR
2 CF.B
8 8 8
MONO SPLIT STEREO 1 MASTER
7 7 7
6 6 6
5 5 5
4 4 4 TIME
MIXING
3 3 3 0
2 2 2
EQ CURVE
1 1 1 ISOLATOR EQ
CUE MASTER
LEVEL LEVEL / DEPTH
CH FADER
A THRU B A THRU B A THRU B A THRU B
0 MIN MAX
CROSS FADER ON / OFF
CROSS FADER ASSIGN
PHONES
A B Wireless
CDJ-2000NXS CDJ-2000NXS
Connection procedure
1 Remove the LAN cable from the equipment and unplug the mobile device (iOS/Android) and storage device (USB/SD) from
the DJ player.
! When mobile device (iOS/Android) or storage device (USB/SD) are set, and when LINK connection is established, [PLAYER No.] settings cannot be changed.
En 17
Checking the connections
Check that the player number indicated on the DJ player’s screen is lit in white.
Connecting to LINK Cannot connect to LINK
! In case the player No. lights up gray, LINK connection is not established. When there is a DJ player that is lighted up in gray, redo the connection procedure once again.
! Similarly, check the other DJ players.
1 Connect the computer or mobile device (iOS/Android) to wireless router or access points with wireless LAN.
2 Press the [rekordbox] button.
TAG TRACK
LINK INFO UTILITY BACK / REMOVE
LINK
USB
SD
DISC
AUTO CUE
3 Tap the [LOAD] icon, or click the [LINK] button to establish the link connection.
The devices that have been recognized are indicated on the DJ player’s screen.
18 En
3-2
Connecting rekordbox via cable/Setting the mobile device (iOS/Android) or storage
device (USB/SD)
Equipment used
! CDJ-2000NXS/CDJ-900NXS/XDJ-1000 (1 to 4)
! Switching hub
! USB cable for connecting mobile device (Use the included iPod cable to connect the iPod to the CDJ-2000NXS.)
! Mobile device (iOS/Android) or computer (Mac/Windows) on which rekordbox is installed
! Storage device (USB/SD) on which the music files analyzed by rekordbox are stored.
POWER
WAKE UP
OVER
10 10 10 10 10
9 9 9 9
7 7 7 7 7
MIC 1 HI HI HI HI CH SELECT
4 4 4 4 4 1 2 3 4
0 LEVEL
2 2 2 2 2
MIC A B MST
PARAMETER
MIC 2 1 1 1 1 1 AUTO
TAP BPM
0 0 -26 / 6 0 -26 / 6 0 -26 / 6 0 -26 / 6 0 %
ms
-1 MID -1 MID -1 MID -1 MID -1
HI -2 -2 -2 -2 -2
EQ/ EQ/ EQ/ EQ/
-3 ISO -3 ISO -3 ISO -3 ISO -3
12 12 EQ
DJM-2000NXS/
-24 -24 -24 -24 -24
AUTO
dB -26 / 6 dB -26 / 6 dB -26 / 6 dB -26 / 6 L dB R / TAP TAP
BEAT BEAT BEAT BEAT
COLOR COLOR COLOR COLOR BALANCE
NOISE CUTTER
SOUND COLOR FX
DJM-900NXS/
FILTER FLANGER
TRANS PHASER
CUE CUE CUE CUE CUE
FADER START REVERB ROBOT
SPIRAL SLIP ROLL
1 2 3 4 PITCH ECHO ROLL
MONO STEREO ECHO REV ROLL
DELAY SND/ RTN
DJM-900SRT
4 MIC
Audio cable
10 10 10 3 CF.A
HEAD PHONES 9 9 9
BOOTH MONITOR
2 CF.B
8 8 8
MONO SPLIT STEREO 1 MASTER
7 7 7
6 6 6
5 5 5
4 4 4 TIME
MIXING
3 3 3 0
2 2 2
EQ CURVE
1 1 1 ISOLATOR EQ
CUE MASTER
LEVEL LEVEL / DEPTH
CH FADER
A THRU B A THRU B A THRU B A THRU B
0 MIN MAX
CROSS FADER ON / OFF
CROSS FADER ASSIGN
PHONES
A B USB connections
CDJ-2000NXS CDJ-2000NXS
Connection procedure
1 Remove the LAN cable from the equipment and unplug the mobile device (iOS/Android) and storage device (USB/SD) from
the DJ player.
! When mobile device (iOS/Android) or storage device (USB/SD) are set, and when LINK connection is established, [PLAYER No.] settings cannot be changed.
En 19
Checking the connections
! In case the player No. lights up gray, LINK connection is not established. When there is a DJ player that is lighted up in gray, redo the connection procedure once again.
! Similarly, check the other DJ players.
LINK
USB
SD
DISC
AUTO CUE
! To use a mobile device (iOS/Android) connected by wire: Press the [USB] button.
3 Tap the [LOAD] icon, or click the [LINK] button to establish the link connection.
20 En
Connecting DJ player (Group B) and DJ
4
mixer (Group A)
Connecting rekordbox via cable/Setting the storage device (USB/SD)
Equipment used
BROWSE TAG LIST INFO MENU BROWSE TAG LIST INFO MENU
OFF OFF OFF
POWER ON POWER ON POWER ON
LINK STANDBY LINK STANDBY
MIC MASTER
USB USB
STOP UNLOCK LOCK CD CD CH CD CD STOP UNLOCK LOCK
/DIGITAL PHONO USB 1/2 /DIGITAL LINE USB 3/4 1 2 3 4 SELECT
MIC A B M /DIGITAL LINE USB 5/6 /DIGITAL PHONO USB 7/8
USB USB
MIC +9 10 +9 10 10 +9 10 +9 10
ECHO REVERB SLIP FILTER PHASER SEND/
SD LEVEL ROLL RETURN SD
TIME AUTO
HI 7 HI 7 7 HI 7 HI 7 TIME AUTO
MODE CUE - 0 MODE CUE
HOT CUE 4 4 EFFECT FREQUENCY 4 4 4 HOT CUE
VINYL LOW MID HI VINYL
SPEED ADJUST 2 2 2 2 2 SPEED ADJUST
HI
TOUCH / BRAKE 1 1 1 1 1 TOUCH / BRAKE
EQ -12 +12 -26/ +6 -26/ +6 -26/ +6 -26/ +6
0 0 0 0 0
-12 +12 -2 -2 -2 -2 -2
IN / CUE OUT RELOOP/EXIT NEEDLE SEARCH MIN MAX MIN MAX MIN MAX IN / CUE OUT RELOOP /EXIT NEEDLE SEARCH
CUE / LOOP DELETE MEMORY TALK
CUE / LOOP DELETE MEMORY
EQ/ -3 EQ/ -3 -3 EQ/ -3 EQ/ -3
LOOP CALL RELEASE / START
OFF ON OVER ISO ISO ISO ISO LOOP CALL RELEASE / START
-5 -5 -5 -5 -5
-26/ +6 -7 -26/ +6 -7 1/8 1/4 1/2 3/4 1/1 2/1 4/1 -7 -26/ +6 -7 -26/ +6 -7
CRUSH LPF
DIRECTION TEMPO CUE DIRECTION TEMPO
6 10 16 WIDE 6 10 16 WIDE
FWD PARAMETER FWD
MIN MAX MIN MAX MIN MAX MIN MAX L R
REV REV
MASTER LIVE MASTER
TEMPO
CUE CUE SAMPLER CUE CUE CUE TEMPO
MIN MAX
TRACK SEARCH SYNC MASTER TRACK SEARCH
LINK MONO STEREO
UTILITY
CUE WAKE UP
10 10
HEADPHONES 9 9
BOOTH MONITOR
MONO SPLIT STEREO 8 8
SEARCH MIX SEARCH
7 7
6 6
5 5
4 4 0
MIXING
3
REMIX
3 MIDI
2 2 ON /OFF START/STOP
1 1
Audio cable
0 0
SNAPSHOT
CUE MASTER
0 0
LEVEL CURVE SETTING
ON/OFF
CUE TEMPO CH EQ CUE TEMPO
RESET RESET
CUE
ISOLATOR EQ
- 0 A THRU B A THRU B A THRU B A THRU B
CH FADER
REV FWD REV FWD
PLAY / PAUSE CROSS FADER ASSIGN CROSS FADER ASSIGN PLAY / PAUSE
TEMPO
PHONES
A B
CROSS FADER
TEMPO
LAN cable (wired)
MULTI PLAYER
CDJ-2000 MULTI PLAYER
CDJ-2000
PROFESSIONAL MIXER
DJM-2000 nexus
Connection procedure
1 Remove the LAN cable from the equipment and unplug the storage device (USB/SD) from the DJ player.
! When storage device (USB/SD) is set, and when LINK connection is established, [PLAYER No.] settings cannot be changed.
En 21
Connecting the cables (LAN cable and audio cables)
CONTROL
CD DIGITAL
R
AUDIO OUT
L
CONTROL DIGITAL
OUT
OFF POWER CD DIGITAL CD DIGITAL O) CD DIGITAL CD DIGITAL
R
AUDIO OUT
L
CONTROL DIGITAL
OUT
ON
R R R R
MASTER1 MASTER2 REC OUT BOOTH SEND
LINK
RETURN CH 3 CH 1 COMPUTER 1
R L L TRS MIDI OUT USB
LINK USB MASTER R L R L(MONO) R L(MONO) LINK USB
AC IN ATT.
LINK
-6dB -3dB 0dB
CH 4 CH 2 COMPUTER 2
R
1GND 2HOT CH 4 CH 2 COMPUTER 2
3COLD
Checking the DJ player’s link established by LAN connection (for the CDJ-2000)
Check that the player number indicated on the DJ player’s screen is lit in white.
Connecting to LINK Cannot connect to LINK
! In case the player No. lights up gray, LINK connection is not established. When there is a DJ player that is lighted up in gray, redo the connection procedure once again.
! Similarly, check the other DJ players.
Checking the DJ player’s link established by LAN connection (for the CDJ-900)
Touch and hold the [MENU/UTILITY] button of DJ player for 1 second or more to open the [UTILITY] screen, and confirm that
[LINK STATUS] is set to [CONNECTED].
Connecting to LINK Cannot connect to LINK
UTILITY UTILITY
PLAYER No. 2 PLAYER No. 2
LINK STATUS CONNECTED LINK STATUS NOT CONNECTED
AUTO STANDBY ON AUTO STANDBY ON
MIDI CHANNEL – MIDI CHANNEL –
! In case [NOT CONNECTED] is displayed, LINK connection is not established. In case of the DJ player where [NOT CONNECTED] is displayed, redo the connection proce-
dure once again.
! Similarly, check the other DJ players.
Checking that the LAN cable and audio cables are synchronized
Load a music file, then operate the DJ players that are connected by link to play and pause the track repeatedly.
Check that the player number displayed on the DJ player’s screen is the same as the channel number that lights on the DJ mixer’s channel level indicator.
If it does not match, the connection is considered to be incorrect. Redo the connection procedure once again.
CD CD
/DIGITAL PHONO USB 1/2 /DIGITAL LINE USB 3/4
TRIM TRIM
OVER OVER
+9 10 +9 10
HI 7 HI 7
4 4
2 2
1 1
-26/ +6 -26/ +6
0 0
MID -1 MID -1
-2 -2
EQ/ -3 EQ/ -3
ISO ISO
-5 -5
CDJ-2000 -26/ +6 -7
- 10
-26/ +6 -7
- 10
LOW LOW
- 15 - 15
-24 -24
dB dB
-26/ +6 -26/ +6
FILTER FILTER
CDJ-900 DJM-2000NXS
! Similarly, check the other DJ players.
22 En
Checking the connected device(s)
1 Press one of the medium select buttons to check the connection with the respective device.
— To use a computer (Mac/Windows) connected by wired LAN: Press the [LINK] button.
— When a storage device (USB/SD) set to other players where LINK is connected is to be used: Press the [LINK] button.
— To use a USB device connected by wire to the USB (A terminal): Press the [USB] button.
— To use an SD memory card: Press the [SD] button.
! The following describes an example for when using a computer (Mac/Windows) connected by wired LAN (for when the [LINK] button is pressed).
LINK
USB
DISC
TIME AUTO
MODE CUE
rekordbox (Mac/Windows)
The files, folders and lists loaded into the respective devices are displayed on the DJ player’s screen.
rekordbox (Mac/Windows)
This completes checking the connections.
En 23
Connecting DJ player (Group B) and DJ
5
mixer (Group B)
Connecting rekordbox via cable/Setting the storage device (USB/SD)
Equipment used
! CDJ-2000/CDJ-900 (1 to 4)
! Switching hub
! Computer (Mac/Windows) on which rekordbox is installed
! Storage device (USB/SD) on which the music files analyzed by rekordbox are stored.
! DJM-900NXS or DJM-900SRT
! Audio cable
! LAN cables (one for each DJ player + two more)
0
DISC EJECT TRIM TRIM TRIM TRIM DISC EJECT
SD SD
OVER OVER OVER OVER OVER CH SELECT
1 2 3 4
10 10 10 10 10
DISC MIC 1 MIC A B MS T DISC
7 9 7 9 7 9 7 9 7 PARAMETER
DIRECTION TEMPO NOISE CRUSH FILTER LOW HI LOW HI LOW HI LOW HI DIRECTION TEMPO
L R
6 10 16 WIDE 6 10 16 WIDE
FWD FLANGER PHASER FWD
LINK CUE CUE CUE CUE CUE
FILTER ROBOT
REV TRANS MELODIC REV
REVERB SLIP ROLL
CUE
MASTER SPIRAL ROLL MASTER
TEMPO MONO STEREO ECHO REV ROLL TEMPO
FADER START DELAY MIDI LFO
SND/ RTN
TRACK SEARCH TRACK SEARCH
1 2 3 4 4 MIC
3 CF.A
10 10 10
2 CF.B
HEADPHONES 9 9 9 BOOTH MONITOR
1 MASTER
8 8 8
MONO SPLIT STEREO
7 7 7
SEARCH 6 6 6 SEARCH
5 5 5 TIME
4 4 4
MIXING 0
3 3 3
2 2 2
1 1 1
EQ CURVE
ISOLATOR EQ
0 0 0
Audio cable
CUE MASTER
LEVEL LEVEL / DEPTH
0 CH FADER 0
A THRU B A THRU B A THRU B A THRU B
CUE TEMPO CUE TEMPO
RESET RESET
0 MIN MAX
A B
TEMPO TEMPO
MULTI PLAYER
CDJ-2000 MULTI PLAYER
CDJ-2000
Connection procedure
1 Remove the LAN cable from the equipment and unplug the storage device (USB/SD) from the DJ player.
! When storage device (USB/SD) is set, and when LINK connection is established, [PLAYER No.] settings cannot be changed.
24 En
Connecting the cables (LAN cable and audio cables)
CH 3 CH 2
LINE CD/ LINE LINE CD/ LINE
L L
CH 4 CH 3 CH 2 CH 1
R R R R
MASTER1 R MASTER2 REC OUT BOOTH R DIGITAL
R L LINK USB R
SEND
L (MONO)
R L L
MASTER2 REC OUT
R
L TRS
L BOOTH
LINK MASTER
CH2 CH1
R L LINK USB
OUT
IN
L L L TRS
L R
R R L RR
AC IN 2 HOT
CH4 CH3
1 GND
3 COLD
Checking the DJ player’s link established by LAN connection (for the CDJ-2000)
Check that the player number indicated on the DJ player’s screen is lit in white.
Connecting to LINK Cannot connect to LINK
! In case the player No. lights up gray, LINK connection is not established. When there is a DJ player that is lighted up in gray, redo the connection procedure once again.
! Similarly, check the other DJ players.
Checking the DJ player’s link established by LAN connection (for the CDJ-900)
Touch and hold the [MENU/UTILITY] button of DJ player for 1 second or more to open the [UTILITY] screen, and confirm that
[LINK STATUS] is set to [CONNECTED].
Connecting to LINK Cannot connect to LINK
UTILITY UTILITY
PLAYER No. 2 PLAYER No. 2
LINK STATUS CONNECTED LINK STATUS NOT CONNECTED
AUTO STANDBY ON AUTO STANDBY ON
MIDI CHANNEL – MIDI CHANNEL –
! In case [NOT CONNECTED] is displayed, LINK connection is not established. In case of the DJ player where [NOT CONNECTED] is displayed, redo the connection proce-
dure once again.
! Similarly, check the other DJ players.
Checking that the LAN cable and audio cables are synchronized
Load a music file, then operate the DJ players that are connected by link to play and pause the track repeatedly.
Check that the player number displayed on the DJ player’s screen is the same as the channel number that lights on the DJ mixer’s channel level indicator.
If it does not match, the connection is considered to be incorrect. Redo the connection procedure once again.
TRIM TRIM
OVER OVER
10 10
7 9 7 9
4 HI 4 HI
2 2
1 1
CDJ-2000 0
-26 /
0
-26 /
6 6
-1 -1
MID MID
-2 -2
-3 EQ/ -3 EQ/
ISO ISO
-5 -5
- 7 -26 / 6 - 7 -26 / 6
-10
LOW -10
LOW
-15 -15
-24 -24
CDJ-900 DJM-900NXS
! Similarly, check the other DJ players.
En 25
Checking the connected device(s)
1 Press one of the medium select buttons to check the connection with the respective device.
— To use a computer (Mac/Windows) connected by wired LAN: Press the [LINK] button.
— When a storage device (USB/SD) set to other players where LINK is connected is to be used: Press the [LINK] button.
— To use a USB device connected by wire to the USB (A terminal): Press the [USB] button.
— To use an SD memory card: Press the [SD] button.
! The following describes an example for when using a computer (Mac/Windows) connected by wired LAN (for when the [LINK] button is pressed).
LINK
USB
SD
DISC
TIME AUTO
MODE CUE
rekordbox (Mac/Windows)
The files, folders and lists loaded into the respective devices are displayed on the DJ player’s screen.
rekordbox (Mac/Windows)
This completes checking the connections.
26 En
Connecting DJ player (Group B) and other
6
DJ mixers
Connecting rekordbox via cable/Setting the storage device (USB/SD)
Equipment used
! CDJ-2000/CDJ-900 (1 to 4)
! Switching hub
! Computer (Mac/Windows) on which rekordbox is installed
! Storage device (USB/SD) on which the music files analyzed by rekordbox are stored.
! Other DJ mixers (DJ mixers other than DJM-2000NXS/DJM-2000/DJM-900NXS/DJM-900SRT)
! Audio cable
! LAN cables (one for each DJ player + one more)
BROWSE TAG LIST INFO MENU POWER BROWSE TAG LIST INFO MENU
OFF OFF
POWER ON POWER ON
LINK STANDBY LINK STANDBY
USB
MIC USB MASTER MIDI USB
STOP UNLOCK LOCK LEVEL ON/ OFF START STOP UNLOCK LOCK
MIC1 CD/LINE PHONO USB CD/LINE LINE USB CD/LINE LINE USB CD/LINE PHONO USB / STOP
UTILITY
USB 1/2 3/4 5/6 7/8 USB
OVER
DISC DISC
10 10 10 10 10
SD 9 9 9 9 SD
7 7 7 7 7
TIME AUTO MIC 1 HI HI HI HI CH SELECT TIME AUTO
MODE CUE MODE CUE
4 4 4 4 4 1 2 3 4
HOT CUE HOT CUE
VINYL 0 LEVEL VINYL
2 2 2 2 2
MIC A B MST
SPEED ADJUST PARAMETER
SPEED ADJUST
TOUCH / BRAKE MIC 2 1 1 1 1 1 AUTO TOUCH / BRAKE
TAP BPM
0 0 -26 / 6 0 -26 / 6 0 -26 / 6 0 -26 / 6 0 %
ms
-1 MID -1 MID -1 MID -1 MID -1
IN / CUE OUT RELOOP/EXIT NEEDLE SEARCH HI -2 -2 -2 -2 -2 IN / CUE OUT RELOOP /EXIT NEEDLE SEARCH
CUE / LOOP DELETE MEMORY CUE / LOOP DELETE MEMORY
EQ/ EQ/ EQ/ EQ/
LOOP CALL -3 ISO -3 ISO -3 ISO -3 ISO -3 LOOP CALL
RELEASE / START 12 12 EQ RELEASE / START
DJM-2000NXS/
REC / CALL -24 -24 -24 -24 -24 REC / CALL
LOOP CUTTER LOOP CUTTER
VINYL AUTO VINYL
LIGHT HEAVY
JOG dB -26 / 6 dB -26 / 6 dB -26 / 6 dB -26 / 6 L dB R / TAP TAP LIGHT HEAVY
JOG
MODE BEAT BEAT BEAT BEAT MODE
CDJ CDJ
COLOR COLOR COLOR COLOR BALANCE
NOISE CUTTER
DJM-2000/
DIRECTION DIRECTION
TEMPO SOUND COLOR FX CUE TEMPO
6 10 16 WIDE 6 10 16 WIDE
FWD FWD
CRUSH FILTER L R
LOW HI LOW HI LOW HI LOW HI
REV REV
DJM-900NXS/
FILTER FLANGER
MASTER TRANS PHASER MASTER
TEMPO CUE CUE CUE CUE CUE TEMPO
FADER START REVERB ROBOT
SPIRAL SLIP ROLL
TRACK SEARCH 1 2 3 4 PITCH ECHO ROLL TRACK SEARCH
MONO STEREO ECHO REV ROLL
DELAY SND/ RTN
DJM-900SRT
4 MIC
10 10 10 3 CF.A
HEAD PHONES 9 9 9
BOOTH MONITOR
2 CF.B
SEARCH 8 8 8 SEARCH
MONO SPLIT STEREO 1 MASTER
7 7 7
6 6 6
5 5 5
4 4 4 TIME
MIXING
3 3 3 0
2 2 2
EQ CURVE
Audio cable
1 1 1 ISOLATOR EQ
0 0 0
0 0
CUE MASTER
PHONES
TEMPO TEMPO
A B
MULTI PLAYER
CDJ-2000 MULTI PLAYER
CDJ-2000
CDJ-2000 CDJ-2000
Connection procedure
1 Remove the LAN cable from the equipment and unplug the storage device (USB/SD) from the DJ player.
! When storage device (USB/SD) is set, and when LINK connection is established, [PLAYER No.] settings cannot be changed.
En 27
Checking the connections
Checking the DJ player’s link established by LAN connection (for the CDJ-2000)
Check that the player number indicated on the DJ player’s screen is lit in white.
Connecting to LINK Cannot connect to LINK
! In case the player No. lights up gray, LINK connection is not established. When there is a DJ player that is lighted up in gray, redo the connection procedure once again.
! Similarly, check the other DJ players.
Checking the DJ player’s link established by LAN connection (for the CDJ-900)
Touch and hold the [MENU/UTILITY] button of DJ player for 1 second or more to open the [UTILITY] screen, and confirm that
[LINK STATUS] is set to [CONNECTED].
Connecting to LINK Cannot connect to LINK
UTILITY UTILITY
PLAYER No. 2 PLAYER No. 2
LINK STATUS CONNECTED LINK STATUS NOT CONNECTED
AUTO STANDBY ON AUTO STANDBY ON
MIDI CHANNEL – MIDI CHANNEL –
! In case [NOT CONNECTED] is displayed, LINK connection is not established. In case of the DJ player where [NOT CONNECTED] is displayed, redo the connection proce-
dure once again.
! Similarly, check the other DJ players.
1 Press one of the medium select buttons to check the connection with the respective device.
— To use a computer (Mac/Windows) connected by wired LAN: Press the [LINK] button.
— When a storage device (USB/SD) set to other players where LINK is connected is to be used: Press the [LINK] button.
— To use a USB device connected by wire to the USB (A terminal): Press the [USB] button.
— To use an SD memory card: Press the [SD] button.
! The following describes an example for when using a computer (Mac/Windows) connected by wired LAN (for when the [LINK] button is pressed).
LINK
USB
SD
DISC
TIME AUTO
MODE CUE
rekordbox (Mac/Windows)
28 En
The files, folders and lists loaded into the respective devices are displayed on the DJ player’s screen.
En 29