Professional Documents
Culture Documents
UW-F4 Service Manual
UW-F4 Service Manual
Confidential
GLORY
Records of Revision
02 - -
03 - -
04 - -
05 - -
06 - -
07 - -
08 - -
09 - -
10 - -
11 - -
12 - -
13 - -
14 - -
15 - -
16 - -
17 - -
1. CONSTITUTION OF MACHINE P1
EXTERNAL APPEARANCE (UW-F4 series) P1
FEED, BILLVALIATION,
RJ TRANSPORT, OPTION BIL VALIDATION P2
TRANSPORT 1 P3
PLACEMENT OF ELECTRIC BOARDS P4
LAYOUT OF SENSORS AND ACTUATORS P5
NAME OF SENSOR AND ACTUATOR P6
EXTERNAL APPEARANCE (YUWF-10-ST,YUWF-11-ST) P7
TRANSPORT 2, TRANSPORT STACKER P8
PLACEMENT OF ELECTRIC BOARDS P9
LAYOUT OF SENSORS AND ACTUATORS P 10
NAME OF SENSOR AND ACTUATOR P 11
Appendix P 137
WIRING DIAGRAMS P 137
CONNECTOR LAYOUT DRAWING P 144
Maintenance unit, PCB and Parts compatibility with other Product P 148
SETTING LIST P 148
0. BEFORE MAINTAIN
BATTERY BATTERY
BATTERY
CAUTION
ATTENTION
2 1
CNBAT
1. CONSTITUTION OF MACHINE
UW-F4 series
EXTERNAL APPEARANCE
Feed
For setting notes.
Capacity: max. 2000 notes
Inter Face
For the other device.
Touch screen
Screen functioning as a
display as well as a key pad. Handle
Handle for opening the
Stacker upper body.
Stacker for the counted notes.
Capacity:300 notes (max.500notes)
RJ transport
Handle 2
To open the
upper transport.
Handle
To open the
upper transport part.
Handle 6 Handle 1
Handle for opening/closing Handle for opening the
the upper transport part. upper cover.
Transport 1
Handle
Handle for opening/closing
the lower transport.
9
11
7
8
12
10
6
5
4
3
△1
FAN FAN
YUWF-10-ST、YUWF-11-ST
EXTERNAL APPEARANCE
Stacker
Stacker for the counted notes. Handle
Capacity:100 notes (max.200notes) Handle for opening the
Front door.
Transport 2
Handle
To open the
Upper transport.
Transport stacker
Handle
To open the
Lower transport.
Photo Interrupter
There are the following three kinds of targets for software installation.
- Batch software installation of main section, mechanism control section and bill validation section
- Software installation for main section
- Software installation for main boot section
[1]
[2]
Group Items
Denomination Setting
SUSP Threshold Setting
FIT Threshold Setting
Stacker Pattern
Setting data Batch Number Setting
Machine Setting
BV Setting
Default Setting
Note Info Output Setting
All Machine Log
Service Log
Log
Mechanical Information Log
Application Log
Transaction Database
Database
Serial Number Database
(10) After finished, remove the machine SD card from the slot.
NOTE) The folder structure of the maintenance SD card refer to next page
Root
Backup1
Setting
UW_Setting_yyyymmddhhmmss_nnnnnn *1*2
Current
BatchCountConfiguration.xml Number of batch setting file
Fit-UnfitConfiguration.xml Threshold of Fitness setting file
MachineConfiguration.xml Machine setting file
NoteInformationOutputConfiguration.xml Serial number output setting file
StackerConfiguration.xml Stacker patterns setting file
True-FalseConfiguration.xml Threshold of authenticity setting file
Default
BatchCountConfiguration.xml Contents are same with "Currency"
…
UW_Log
UW_Log_yyyymmddhhmmss_nnnnnn *1*2
yyyymmdd
nn *3
log-yyyymmdd_nn_nnnnnn.static.txt *3*Application Log files
SerialNumberdb
yyyymmdd
SerialNumber.db Serial number database file
SerialManagement.db Serial number management file
Transactiondb
yyyymmdd
Transaction.db Transaction database file
TransactionManagement.db Transaction management file
UW_ALL.log All machine log file
UW_DBG.log Mechanical information log file
UW_SVS.log Service log file
BV_EVENT.log BV event log file
BV_STEP.log BV step log file
*1 “yyyymmddhhmmss“ shows the date and time log data was exported.
*2 “nnnnnn” shows serial number of the machine.
*3 "nn" shows serial number of each file.
*4 "nnnnnn" shows serial number of each file.
* Log analysis requires all files in "Backup1" folder and "UW_Log" folder.
* Delete old files in SD card/USB flash memory which are already stored.
[1]
[2]
Root
Conf
Current
BatchCountConfiguration.xml Number of batch setting file
Fit-UnfitConfiguration.xml Threshold of Fit-Unfit setting file
MachineConfiguration.xml Machine setting file
NoteInformationOutputConfiguration.xmSerial number output setting file
StackerConfiguration.xml Stacker patterns setting file
True-FalseConfiguration.xml Threshold of True-false setting file
Default
BatchCountConfiguration.xml Contents are same with "Currency"
…
SerialNumberDB
yyyymmdd
SerialNumber.db Serial Number Database file
SerialManagement.db Serial Number Management file
TransactionDB
yyyymmdd
Transaction.db Transaction Database file
TransactionManagement.db Transaction Management file
Group Items
Denomination Setting
SUSP Threshold Setting
FIT Threshold Setting
Stacker Pattern
Setting data Batch Number Setting
Machine Setting
BV Setting
Default Setting
Note Info Output Setting
Transaction Database
Database
Serial Number Database
(10) After finished, remove the maintenance SD card from the slot.
[1]
[2]
(8) After finished, remove the machine SD card from the slot.
NOTE) The folder structure of the maintenance SD after executing data backup is as follows
Root
BackupRestore
UW_nnnnnn *1
LanguageData Language Data folder
Machine Setting Folder No.1
Setting Setting Folder No.2
SerialNumberDB Serial Number Database folder
TransactionDB Transaction Database folder
[1]
[2]
(8) After finished, remove the machine SD card from the slot.
NOTE) The folder structure of the maintenance SD card refer to next page
No Tools
1 Penlight
2 Cloth
3 Cleaning brush
4 Blower
UW-F4 series
units contents of periodic inspection remark
Feed (1)check foreign object
(2)check rollers and clean
(3)check sensors and clean
Bill validation (1)check foreign object
(2)check sensors and clean
Op bill (1)check foreign object
validation (2)check sensors and clean
RJ transport (1)check foreign object
(2)check rollers and clean
(3)check sensors and clean
Transport 1 (1)check foreign object
(2)check rollers and clean
(3)check sensors and clean
(4)check dumper condition
(5)check Dust tray
Stacker (1)check foreign object
(2)check sensors and clean
(3)check reflection surface and clean
YUWF-10-ST、YUWF-11-ST
units contents of periodic inspection remark
(1)check foreign object
Transport 2 (2)check rollers and clean
(3)check sensors and clean
(1)check foreign object
Transport
(2)check rollers and clean
stacker
(3)check sensors and clean
(note)
Inspection cycle is 6 months.
Please lecture cleaning method to customers due to avoid from machine trouble.
When you clean up inner of the machine, mind to turn off power switch.
If you don't, it will cause electric shock or injury.
Don't use neutral detergent, benzine, thinner, compounded wax, etc. to clean
the product. It becomes to fade, damage and cause machine trouble.
Model UW-F4 series Visually check that notes are discharged, and prevent
Purpose
Part Feed error due to abnormal transfer of notes.
Necessary
Check feed none
Contents tools
condition
Operation time 3 min. Inspection cycle 6 months
No Procedure Drawing
(1) Lock feed roller and
gate roller
rotate the gate
roller direction of
pointing arrow A.
And check that A
it rotates smoothly.
gate roller
feed roller
handle4
(7) Clean these 8 sensors,
remove dust and
foreign object by
cleaning brush.
handle2
(4) Hold and open handle5
note)
・Do NOT use wet
cloth & alcohole.
・Do NOT get up any
magnetic material.
No Procedure Drawing
(6) Hold and open
handle6
handle6
handle
(2) Clean the dust tray dust tray
by cleaning brush
and blower.
handle
(2) Hold handle1 and
open the transport 1.
handle 1
Reflection surface
Model YUWF-1*-ST
Purpose Obviate errors of sensors
Part transport 2
Necessary
Cleaning Brush, Blower
Contents Clean sensors tools
Operation time 5 min. Inspection cycle 6 months
No Procedure Drawing
(1) Hold handle1 and
open the front cover.
handle1
Model YUWF-1*-ST
Purpose Obviate errors of sensors
Part transport stacker
Necessary
Cleaning Brush, Blower
Contents Clean sensors tools
Operation time 5 min. Inspection cycle 6 months
No Procedure Drawing
(1) Check visually that
foreign matter are not
in each Stacker unit.
handle1
handle2
(3) Clean these 8 sensors,
remove dust and
foreign object
by cleaning brush.
(2) Please make service log clear. ※Refer to RAS [Clear Service Log]
UW-F4 series
Maintenance module Item name Item code pcs Periodic replacement cycle
- GAS SPRING H6M2Z1911Z0 2 2 years
FEED ROLLER MV80LB210Z0 4 30 million pieces or 2 years
FEED BLOCK GATE ROLLER N140B00F0Z0 4 30 million pieces or 2 years
KICK BELT 314901660 3 15 million pieces
FLAT BELT 31430530 2 30 million pieces or 2 years
FLAT BELT J610J5211Z0 2 30 million pieces or 2 years
RJ TRANSPORT FLAT BELT 31430714 2 30 million pieces or 2 years
UNIT FLAT BELT 3143T221 2 30 million pieces or 2 years
FLAT BELT 31431063 2 30 million pieces or 2 years
FLAT BELT 31430528 2 30 million pieces or 2 years
FLAT BELT 31431241 2 30 million pieces or 2 years
TRANSPORT 1 FLAT BELT 31431002 2 30 million pieces or 2 years
UNIT FLAT BELT H810F2307Z0 2 30 million pieces or 2 years
FLAT BELT 31431530 2 30 million pieces or 2 years
YUWF-10-ST、YUWF-11-ST
Maintenance module Item name Item code pcs Periodic replacement cycle
FLAT BELT 31430718 2 30 million pieces or 2 years
FLAT BELT 3143T221 2 30 million pieces or 2 years
FLAT BELT 31431094 2 30 million pieces or 2 years
ADDITIONAL
FLAT BELT DE42M1151Z0 2 30 million pieces or 2 years
STACKER UNIT
FLAT BELT 31431476 2 30 million pieces or 2 years
FLAT BELT 31430340 2 30 million pieces or 2 years
FLAT BELT 31430714 2 30 million pieces or 2 years
No Tools
1 Phillips screwdriver
2 Flathead screwdriver
3 Phillips screwdriver(small)
4 Flathead screwdriver(small)
5 Phillips screwdriver(long shaft)
6 Ratchet type screwdriver
7 Precision driver
8 Long nose pliers
9 Pliers
10 Nipper
11 Wrench (M3-M8)
12 Ratchet type wrench (M3-M8)
13 Hexagonal wrench (M3-M10)
14 Scale (150mm)
15 Penlight
16 Digital type tester
17 Cloth
18 Thickness gauge (t=0.06,0.07,0.08mm)
19 Grease (*1)
20 Thickness gauge (t=1.0,1.2mm)
21 Tension gauge (Spring scale)
22 Screw Lock
23 Cleaning brush
24 Blower
25 HP ADJUST TOOL SET(QH10H1070Z0)
26 GSP SHAFT FOR EXCHANGE(JB50Z1194Z0)
27 ROLLER ADJUST TOOL(JB50B1999Z0)
Replacement
No. Replacement procedure Reference diagram
target unit
1 2
GSP GAS SPRING Make sure remove all the banknote from screw A
handle
the machine, and power off the machine.
HP cover
1 Hold handle and open the Front cover.
3,4
4 Hold handle and close the Front cover.
handle
Replacement
No. Replacement procedure Reference diagram
target unit
5 6
GSP GAS SPRING 5 Hold handle and open the upper unit.
Replacement
No. Replacement procedure Reference diagram
target unit
Replacement
No. Replacement procedure Reference diagram
target unit
10
GSP GAS SPRING 10 Unlock the damper, and pull out 2 pins.
11
PULL
screw D
Shaft
Replacement
No. Replacement procedure Reference diagram
target unit
13 14
GSP GAS SPRING After replacing damper, check screw A
dimensions by following procedure,If it is handle
not within dimension, adjust according to
"GSP-19~GSP-24" procedure. HP cover
screw A
Cover R
15 Remove 4 screws
F(ABW4X8,black),and take off Cover L.
15
screw F
screw F
Cover L
Replacement
No. Replacement procedure Reference diagram
target unit
A B
Replacement
No. Replacement procedure Reference diagram
target unit
GSP GAS SPRING 19 Remove the Gas spring by the procedure 20 21 Cover C
"GSP-1~GSP-12".
Cover R
screw H screw H
Replacement
No. Replacement procedure Reference diagram
target unit
1, 3,4
FEED FEED Make sure remove all the banknote from
ROLLER the machine, and power off the machine.
1 2
bearing WW8
Replacement
No. Replacement procedure Reference diagram
target unit
5
FEED FEED 5 Remove the Feed assy while removing
ROLLER the Timing belt.
6 Spacer Bearing
E-6
Feed roller
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度
品 名 調 整 値 条 件 保守基準値 条 件 Pass through adjust tool into hole of shafts
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD N140
adjust tool (JB50B1999Z0)
MV80LB210Z0 フィードローラとキック 右図のゴム位置で 調整 未達成時の不具合: B0004
フィードローラセット ローラの位相 それぞれの軸に 繰出し不良 N140
N140B0003Z0 治具が貫通するこ B0003
A キック1ローラ と ← ←
N140B0004Z0
キック2ローラ MV80
LB210
NNN0A51E0Z0 adjustment of Pass through adjustment Possible problem:
Feed Roller timing Kicker adjust tool into Miss feeding
N140B0003Z0 Roller and Feed hole of shafts
A Kicker Roller 1 when rubber ← ←
Roller
NF70A21L1Z0 places in drawing
Kicker Roller 2
QH10
A2131
QH10
A2121
QH10
A2111
TMB6-9362
Page 50
Replacement
No. Replacement procedure Reference diagram
target unit
2
GATE GATE Make sure remove all the banknote from
handle
ROLLER the machine, and power off the machine.
bush
Replacement
No. Replacement procedure Reference diagram
target unit
4
GATE GATE 4 Remove 3 screws B(CRW3X8),and take
ROLLER off the Gate roller assy.
screw B
Replacement
No. Replacement procedure Reference diagram
target unit
5 6
GATE GATE 5 Remove screw C(TSPP3X8), and take off Bearing
ROLLER the Arm plate and Bearing.
No printing side
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 品質特性 備 考
PART No. STANDARD VALUE A arrow view
度
品 名 調 整 値 条 件 保守基準値 条 件
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
QH10
QH10A22F1Z0 取付位置 右図のハンドルの穴 目視 未達成時の不具合:
からカムの穴(赤丸 繰出し不良 A22D1
ハンドル
QH10A22D1Z0 部)が見えること
A カム ← ←
QH10
QH10A22F1Z0 Attach position The cam hole (red Visually Possible problem: A22F1
Handle circle) can be seen Miss feeding
QH10A22D1Z0 from the handle A
A Cam hole on the right ← ←
figure
Standard setting
QH10A22F1Z0 Attach position Turn the handle to Possible problem:
Handle fix it in the ・Miss feeding
position shown ・Increase RJ by SKEW
A ← ← and CHAIN
If Increase RJ by CHAIN and Double 1 If Increase RJ by SKEW or feel that hard to feed bills repetitive
TMB6-9362
Confidential Page 54
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 品質特性 備 考 Pushing
PART No. STANDARD VALUE
度
品 名 調 整 値 条 件 保守基準値 条 件
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
QH10A10F1Z0 取付位置 矢印方向に寄せ 確認 未達成時の不具合:
ストッパー て取り付け 繰出し不良
斜行 QH10
31500176
ローラ A=0.5mm以下 A10F1
N140B0003Z0 サツオセを降ろした
キック1ローラ 状態で、サツオサエ
A のローラとキック1ローラ ← ←
がA寸法以下であ
る事を確認
Adjusting screw Arrow
3150
0176
N140
B0003
TMB6-9362
Page 55
Replacement
No. Replacement procedure Reference diagram
target unit
2 3
KICK KICK BELT Make sure remove all the banknote from Width
the machine, and power off the machine. regulating
plate
1 Remove Feed unit by the procedure "A-1
~ A11".
2 Remove 4 screws A(CRW3X6), and take
off the width regulating plate.
3 Disconnect the CNA12 connector.
CNA12
4 Remove 2 screws B(CRW4X8), and take
off the Under guide.
screw A
5 Detatch Kick belt in the direction of
arrow A.
6 To mount Kick belt, check the direction
of kick belt and reverse the procedure.
4 5
High Low
A
Kick belt
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度
品 名 調 整 値 条 件 保守基準値 条 件
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
QH10A21E1Z0 取付位置 A方向に当て付け 目視 未達成時の不具合:
シタガイド2 繰出し不良
斜行
A ← ←
QH10
A21E1
TMB6-9362
Page 57
Replacement
No. Replacement procedure Reference diagram
target unit
1 2
A FEED UNIT Make sure remove all the banknote from screw A
handle
the machine, and power off the machine.
HP cover
1 Hold handle and open the front cover.
3 4
4 Remove 2 screws B(CRW3X6,black),and
take off the BV driving cover.
Replacement
No. Replacement procedure Reference diagram
target unit
5 6
A FEED UNIT 5 Remove a screw C(CRW3X6,black),and
take off the Connector cover.
A
A arrow view
7 7
screw D screw D
Replacement
No. Replacement procedure Reference diagram
target unit
8 Cover C
A FEED UNIT 8 Remove 5 screws E(ABW4X8,black),
and detatch Cover C.
screw E
9 10
Press
Timing belt
FEED UNIT
Replacement
No. Replacement procedure Reference diagram
target unit
12
A FEED UNIT 12 Disconnect the CAN11,CAN17
connectors.
13 Remove 4 screws F(ABW4X8,black).
CNA11
CNA17
Press
13
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度
品 名 調 整 値 条 件 保守基準値 条 件
RANK OBJECT REMARKS
PART NAME ASSEMBLINGMETHOD MAINTENANCE METHOD Standard setting
QH10A22F1Z0 取付位置 ハンドルを回して 目視 未達成時の不具合:
ハンドル 図の位置に固定 ・繰出し不良
する ・斜行、連鎖
A ← ←
If Increase RJ by CHAIN and Double 1 If Increase RJ by SKEW or feel that hard to feed bills repetitive
TMB6-9362
Confidential Page 62
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 品質特性 備 考 Pushing
PART No. STANDARD VALUE
度
品 名 調 整 値 条 件 保守基準値 条 件
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
QH10A10F1Z0 取付位置 矢印方向に寄せ 確認 未達成時の不具合:
ストッパー て取り付け 繰出し不良
斜行 QH10
31500176
ローラ A=0.5mm以下 A10F1
N140B0003Z0 サツオセを降ろした
キック1ローラ 状態で、サツオサエ
A のローラとキック1ローラ ← ←
がA寸法以下であ
る事を確認
Adjusting screw Arrow
3150
0176
N140
B0003
TMB6-9362
Page 63
Replacement
No. Replacement procedure Reference diagram
target unit
B1 BILL Make sure remove all the banknote from Rear cover
2 3
VALIDATION the machine, and power off the machine.
UNIT
1 Remove the FEED unit by the procedure
"A-1~A-11".
USB
Connector cover Nylatch CABLE CNBV
Replacement
No. Replacement procedure Reference diagram
target unit
6
B1 BILL 6 Remove a screw C(ABW4X8,black) of A B
A arrow view
VALIDATION tension bearing to loose tension of timing
UNIT belt and detach Bill validation.
7 Remove 4 screws D(ABW4X8,black),
and detatch Bill validation unit.
7
B arrow view
f
screw D
Replacement
No. Replacement procedure Reference diagram
target unit
1 2,3
B2 OP BILL Make sure remove all the banknote from handle handle 1
VALIDATION the machine, and power off the machine.
UNIT
1 Hold handle and open the front cover.
4 Rear cover
4 Remove 2 screws B(ABW4X10,black),
and detatch Rear cover.
screw B
Replacement
No. Replacement procedure Reference diagram
target unit
A arrow view
Replacement
No. Replacement procedure Reference diagram
target unit
6 B
B2 OP BILL 6 Remove 4 screws D(ABW4X8,black),
B arrow view
VALIDATION and detatch OP Bill validation unit.
UNIT
screw D
screw D
Replacement
No. Replacement procedure Reference diagram
target unit
7
B2 OP BILL 7 To mount OP bill validation unit,
C arrow view
VALIDATION positioning the below and reverse the
UNIT procedure.
press
press
D arrow view
press
Replacement
No. Replacement procedure Reference diagram
target unit
1 2
C RJ Make sure remove all the banknote from handle 1
TRANSPORT the machine, and power off the machine. handle
UNIT
1 Hold handle and open the front cover.
3 Rear cover
screw A
Replacement
No. Replacement procedure Reference diagram
target unit
CNC10,CNC20,CNC30
6 Clamp the CNC10,CNC20,CNC30
connectors. 6
4
Connector
cover
clamp
screw B
Replacement
No. Replacement procedure Reference diagram
target unit
7
C RJ 7 Remove 4 screws C(ABW4X8,black).
TRANSPORT
UNIT
screw C
screw C
screw C
Replacement
No. Replacement procedure Reference diagram
target unit
8
C RJ 8 Close Left cover,
TRANSPORT hold handle5 and open OP Bill validation
UNIT unit.
Left cover
10 To mount Rj transport unit, reverse the
procedure. Rj transport unit
9
A arrow view
11 Turn power on and execute sensor
adjustment of Rj transport unit
A
(RAS-Adjust sensors by unit /Rj transport
unit).
screw D
Replacement
No. Replacement procedure Reference diagram
target unit
1 2
D TRANSPORT Make sure remove all the banknote from
1 UNIT the machine, and power off the machine.
Stacker cover
handle
3 4
4 Remove 4 screws B(ABW4X8,black),and
take off Under rear cover.
CND16
screw B Under rear cover
Replacement
No. Replacement procedure Reference diagram
target unit
5 6
Replacement
No. Replacement procedure Reference diagram
target unit
7
D TRANSPORT 7 Remove 4 screws D(ABW4X8,black) and
1 UNIT detach Transport 1 unit. Transport 1 unit
screwD
screw D
Replacement
No. Replacement procedure Reference diagram
target unit
8
D TRANSPORT 8 Remove 4 screws E(ABW4X8,black),and Spring-Balance
1 UNIT take off Under right cover.
Adjustmen
t
Replacement
No. Replacement procedure Reference diagram
target unit
2
E STACKER Make sure remove all the banknote from
CNE10 CNE20 CNE30 CNE40
UNIT the machine, and power off the machine.
CNE51 CNE52 CNE53 CNE54
1 Remove the Transport 1 unit.
※ Refer to D-1~D-7.
3
3 Remove 2 screws A(ABW4X8,black) for
each stacker and detach each Stacker unit.
screw A
Screws position are common
Replacement
No. Replacement procedure Reference diagram
target unit
1 2
Z2-1 ADDITIONAL Make sure remove all the banknote from
STACKER 1 the machine, and power off the machine.
UNIT
1 Remove 2 screws A(ABW4X8,black),and
take off the bracket.
AC POWER CORD
Left cover
CNOP1
CNOP2
CNOP3
Replacement
No. Replacement procedure Reference diagram
target unit
CNE1
CNE2
6 remove 2 screws E(ABW3X6,black).
CNZ2
7 Remove YUWF-10-ST.
screw D Bracket
6 7
PULL
screw E YUWF-10-ST
Replacement
No. Replacement procedure Reference diagram
target unit
8
Z2-1 ADDITIONAL 8 Hold handle and open the Front door. 9
STACKER 1 screw F
UNIT
Harness cover
9 Remove a screw F(CRW3X6), and take
off the Harness cover.
Remove a screw G(BTSS3X6). screw G
11
screw H
Bracket
Replacement
No. Replacement procedure Reference diagram
target unit
12
Z2-1 ADDITIONAL 12 Remove the Front door after 2 pins
STACKER 1 remove from 2 holes.
UNIT
PWR 5
Replacement
No. Replacement procedure Reference diagram
target unit
13 14
Z2-1 ADDITIONAL 13 Hold handle and open the Top front Top front cover
STACKER 1 cover.
UNIT
14 Remove 4 screws I(ABW4X8,black),and
take off the Under Front cover.
handle
screw I
15 Remove 2 screws J(ABW4X8,black), and
take off the Top front cover.
Left cover
screw L
screw L
Replacement
No. Replacement procedure Reference diagram
target unit
17
Z2-1 ADDITIONAL 17 Remove 6 screws L(ABW4X8,black).
STACKER 1 screw L
UNIT
DETACH
Replacement
No. Replacement procedure Reference diagram
target unit
1 2
Z2-2 ADDITIONAL Make sure remove all the banknote from
STACKER 2 the machine, and power off the machine.
UNIT
1 Remove 4 screws A(ABW4X8,black),and
screw B
take off the Rear cover.
CNPW
CNOP21
(back side)
CNOP31
(front side)
Replacement
No. Replacement procedure Reference diagram
target unit
4
Z2-2 ADDITIONAL 4 Remove a screw C(ABW4X8,black).
STACKER 2
UNIT
screw C
screw D
Replacement
No. Replacement procedure Reference diagram
target unit
8 Remove YUWF-11-ST.
screw E
7 8
PULL
Bracket screw F
YUWF-11-ST
Replacement
No. Replacement procedure Reference diagram
target unit
screw F
Z2-2 ADDITIONAL 9 10
If YUWF-11-ST is replaced
STACKER 2
UNIT
9 Hold handle and open the Front door.
screw F
Replacement
No. Replacement procedure Reference diagram
target unit
Replacement
No. Replacement procedure Reference diagram
target unit
1 2
Z2-3 ADDITIONAL Make sure remove all the banknote from
STACKER 2 the machine, and power off the machine.
UNIT
1 Remove 4 screws A(ABW4X8,black),and
screw B
take off the Rear cover.
screw A
CNPW
CNOP21
(back side)
CNOP31
(front side)
Replacement
No. Replacement procedure Reference diagram
target unit
4
Z2-3 ADDITIONAL 4 Remove a screw C(ABW4X8,black).
STACKER 2
UNIT
screw C
screw D
Replacement
No. Replacement procedure Reference diagram
target unit
6
Z2-3 ADDITIONAL 6 Remove a screw E(ABW4X8,black).
STACKER 2
UNIT
8 Remove YUWF-11-ST.
screw E
7 8
PULL
screw F
YUWF-11-ST
Replacement
No. Replacement procedure Reference diagram
target unit
screw F
Z2-3 ADDITIONAL 9 10
If YUWF-11-ST is replaced
STACKER 2
UNIT
9 Hold handle and open the Front door.
screw F
Replacement
No. Replacement procedure Reference diagram
target unit
Replacement
No. Replacement procedure Reference diagram
target unit
ON ON
[Normal position]
bit1 : ON
others : OFF
8 7 6 5 4 3 2 1
OFF OFF OFF OFF OFF OFF OFF
ON
2. Turn on the power switch and touch the cursor as shown in Figure 2
and conduct the calibration of the touch panel.
Figure 2
①Touch top-left of touch panel screen
① ③ ②Touch bottom-left of touch panel screen
⑤ ③Touch top-right of touch panel screen
④Touch bottom-right of touch panel screen
⑤Touch top-center of touch panel screen
② ④
Replacement
No. Replacement procedure Reference diagram
target unit
Make sure remove all the banknote from
1 5
Y-1 CPU+I/O-PC the machine. UPPER
BOARD REAR COVER
UNIT 1 Execute RAS [ MACHINE VERSION ],
and check the software versions. SD card slot
【 APCPU 】U-BOOT, OS, GUI APL,
Main Module,SN Module
9 Disconnect the
CNSD1 CNPW CNSD2
CNLVD,CNLCD,CNSW,CNRC,CNPW CNRC
connectors.
GLORY Class TMB6 Number 9362
Page 97
Replacement
No. Replacement procedure Reference diagram
target unit
screw D
Replacement
No. Replacement procedure Reference diagram
target unit
Replacement
No. Replacement procedure Reference diagram
target unit
Make sure remove all the banknote from
Y-2 CTRL-U the machine.
3 UPPER
BOARD REAR COVER
1 Execute RAS [ MACHINE VERSION ],
and check the software versions.
【 FPGA 】FPGA(CTRL-U)
4 Disconnect the
CNA1,CNA2,CNA3,CNMN1,CNMN2,
CNC1,CNC2,CNC3 connectors.
4
CNA1 CTRL-U BOARD CNC1
CNA2
CNC2
CNA3
CNC3
CNMN2 CNMN1
Replacement
No. Replacement procedure Reference diagram
target unit
5
Y-2 CTRL-U 5 Remove 6 screws J(CRW3X15) and take
BOARD off the CTRL-U BOARD.
FPGA(CTRL-U) is automatically
installed.
Therefore start usually takes time screw J
NOTE more only in the first time.
Replacement
No. Replacement procedure Reference diagram
target unit
Make sure remove all the banknote from
Y-3 MAINCPU the machine. 3
BOARD
UNDER
UNIT 1 Execute RAS [ MACHINE VERSION ], REAR COVER
and check the software versions.
【 MCCPU 】IPL, APL,
【 FPGA 】FPGA(MAIN)
CNE5
screw B
CNFAN,
CND3
MAINCPU BOARD
CNPW1,
Replacement
No. Replacement procedure Reference diagram
target unit
Replacement
No. Replacement procedure Reference diagram
target unit
Replacement
No. Replacement procedure Reference diagram
target unit
Make sure remove all the banknote from
Y-4 ST-V the machine. 3 ※YUWF-10-ST ※YUWF-10-ST/YUWF-11-ST
BOARD
※YUWF- 1 Execute RAS [ MACHINE VERSION ],
10/11-ST and check the software versions.
【 FPGA 】FPGA(ST-V)
REAR COVER
2 Turn off the power switch.
3 ※ YUWF-10-ST
Remove 2 screws A(ABW4X8,black),and
screw A BRACKET
take off the BRACKET. screw A
※ YUWF-10-ST/YUWF-11-ST
Remove 4 screws A(ABW4X8,black),and
4 CNE3 CND4 CND2 CND1
take off the REAR COVER.
ST-V BOARD
4 Disconnect the CNMN1,CNPW1, CNZ1
CNPW2,CNST1,CNZ1,CNZ2,CND1,
CND2,CND3,CND4,CNE1,CNE2, CND3
CNE3 connectors.
CNE1
CNE2
CNZ2
CNMN1
Replacement
No. Replacement procedure Reference diagram
target unit
5
Y-4 ST-V 5 Remove 6 screws H(CRW3X14) and take
BOARD off the ST-V BOARD.
※YUWF-
10/11-ST 6 Assemble the ST-V BOARD in reverse
procedure [Y-4-4 ~ Y-4-5].
screw H
7 Set SW1 as shown in the figure.
FPGA(ST-V) is automatically
installed.
Therefore start usually takes time
NOTE more only in the first time.
7
9 Execute RAS [ MACHINE VERSION ],
and check the software versions.
【 FPGA 】FPGA(ST-V)
※ Make sure that it's the same versions SW1
as procedure [Y-4-1].
Replacement
No. Replacement procedure Reference diagram
target unit
Make sure remove all the banknote from
5
Y-5 POWER the machine.
SUPPLY UNIT
※UW-F4 1 Turn off the power switch and CN1
Replacement
No. Replacement procedure Reference diagram
target unit
Make sure remove all the banknote from
3
Y-6 POWER the machine.
SUPPLY UNIT
※YUWF-10- 1 Turn off the power switch and
ST unplugging the power cord.
Do not touch power supply at
least 2 minutes after unplugging CNMN1 CNPW1 CNPW2 CNST1
the power cord.
CAUTION
CAUTION!
Do not touch the backside of the POWER SUPPLY BOARD.
There is the risk of electric shock..
Replacement
No. Replacement procedure Reference diagram
target unit
Make sure remove all the banknote from
Y-7 LCD the machine. 2 screw B
UNIT
COVER
1 Turn off the power switch.
CN3
Lock lever
CN1
Lock lever
Replacement
No. Replacement procedure Reference diagram
target unit
handle
Replacement
No. Replacement procedure Reference diagram
target unit
Make sure remove all the banknote from
Y-8 TPC BOARD the machine. 3,4
screw D
1 Turn off the power switch.
Replacement
No. Replacement procedure Reference diagram
target unit
Make sure remove all the banknote from
1
Y-9 INTERNAL the machine. SD card slot
SD CARD
1 Remove the machine SD card from the
SD card slot of the right side, insert the
maintenance SD card for saving the log
data.
Then execute RAS [ EXPORT ].
※ Refer to "HOW TO EXPORT DATA"
Replacement
No. Replacement procedure Reference diagram
target unit
9
Y-9 INTERNAL 8 Set the serial number of the machine
SD CARD checked by [ Y-9-2 ].
CNSD1
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度 ※<164mm pattern>
品 名 調 整 値 条 件 保守基準値 条 件 Target country
RANK OBJECT REMARKS ①China
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD ⑪Canada
QH10A10D0Z0 取付位置 図の位置に固定 目視 未達成時の不具合: ②Euro ⑫South Africa
ハバキセイイタLセット する 繰出し不良 ③Japan ⑬Philippines
QH10A10E0Z0 A方向に当て付け 斜行 ④America
A ← ← ⑭Norway
ハバキセイイタRセット ⑤Venezuela ⑮England
⑥Russia ⑯Sweden
⑦Brazil ⑰Australia
QH10A10D0Z0 Attach position Fix to the position Visually Problem when it fails:
⑧Indonesia A A
Width regulation shown Miss feeding
plate L set To impose in A Skew ⑨Mexico
A QH10A10E0Z0 direction ← ← ⑩Nigeria
Width regulation QH10 QH10
plate R set A10D0 A10E0
※<169mm pattern>
Target country
①Iran
②Thailand
③Denmark
④Romania
⑤Korea
⑥Hong Kong / Macao
A A
QH10 QH10
A10D0 A10E0
※<184mm pattern>
Target country
①India
②Taiwan
③Switzerland
QH10
A10E0
QH10
A10D0
A-1
TMB6-9362
Confidential Page 114
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度
品 名 調 整 値 条 件 保守基準値 条 件
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
31421248 ベルトテンション A=2.0 ± 0.3N 調整後、ベル QH10C1051Z0の位置
タイミングベルト B=5.0mm トを2,3回転さ で
C=(90)mm せテンション テンション調整を行う。 3142
QH10C1051Z0 値の確認後、 1464
モーターブラケット NGの場合再 未達成時の不具合:
度調整の事。 ・歯飛び
A 調整後にネ ← ← ・プーリ、ベルトの摩耗
ジロックの ・寿命の低下
事。 ・負荷トルク増大
・ベルト外れ
・異音
31421248
Timing belt
Adjust the belt
tension.
A=2.0 ± 0.3N
B=5.0mm
After adjust,
move the belt
Perform the tension
adjustment by
A
C=(90)mm a few laps. QH10C1051Z0
Then check
QH10C1051Z0 the belt Ploblem when if fails:
Motor bracket tension. If the ・Jumping timing belt.
A belt tension is ← ← ・Wear timing pullies
out of and timing belt.
tolerance ・Reduce life
range, adjust ・Increase load torque
the belt ・Detachment of timing
tension again. belt.
N i
QH10
C1051
C-1
TMB6-9362
Confidential Page 115
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
QH10
度 QH10
C10A0
品 名 調 整 値 条 件 保守基準値 条 件 C10A0
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
QH10C10A0Z0 取付位置 A方向にガタがあ 確認 未達成時の不具合:
ブンキジクセット る事。 ・分岐軸の渋りによる
QH10C10E1Z0 ジャム
カップリング
A ← ←
QH10C10A0Z0
Turning shaft set
Attach position There is the
backlash in the
Check Problem when if fails:
Malfunction of the A A
QH10C10E1Z0 direction shown by Turning shaft set.
Coupling the arrow A Jam
A ← ←
QH10
C10K1
QH10
C10L1
C-2
TMB6-9362
Confidential Page 116
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度
品 名 調 整 値 条 件 保守基準値 条 件
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
QH10C5021Z0 取付位置 矢印方向に調整 確認 未達成時の不具合:
ウシロカバー すること。 ・外観不良
直線Aのズレ:
B ±0.5mm ← ←
QH10C5021Z0
Rear cover
Attatch position Adjust the
direction of the
Check Problem when it fails:
Assembly failure
Line A B
arrow.
B Deviation of the ← ←
straight line A:
±0.5mm
QH10C5041Z0 取付位置 矢印方向に調整 確認 未達成時の不具合:
ヒダリコテイカバー すること。 ・外観不良
2.4mm<B3.4mm
B ← ←
C-3
TMB6-9362
Confidential Page 117
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 品質特性 備 考 QH10
PART No. STANDARD VALUE C5051
度
品 名 調 整 値 条 件 保守基準値 条 件 QH10
RANK OBJECT REMARKS C5081
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
QH10C5051Z0 取付位置 矢印方向に寄せ 確認 未達成時の不具合:
ヒダリトビラカバー て取付けのこと。 ・外観不良
直線Aのズレ:
B ±0.5mm ← ←
Line A
C-4
TMB6-9362
Confidential Page 118
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度
品 名 調 整 値 条 件 保守基準値 条 件 QH10 QH10
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD D1051 D1130
QH10D1130Z0 取付位置 A方向にガタがあ 確認 未達成時の不具合:
ブンキジクセット ること。 ・分岐軸の渋りによる
QH10D1101Z0 ジャム
A カップリング ← ←
QH10
D1130
D-1
TMB6-9362
Confidential Page 119
機種 YUWF-10-ST/YUWF-11-ST
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度 QH11
品 名 調 整 値 条 件 保守基準値 条 件 D2130
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
QH11D2130Z0 取付位置 A方向にガタがあ 確認 未達成時の不具合:
ブンキジクセット る事。 ・分岐軸の渋りによる
QH10D1101Z0 ジャム
カップリング
A ← ←
QH11
D2130
QH11D2130Z0 Attach position There is the Check Problem when if fails:
Turning shaft set backlash in the Malfunction of the
QH10D1101Z0 direction shown by Turning shaft set.
A
Coupling the arrow A
← ←
Jam A
QH10
D1101
QH11D2130Z0 Attach position B=6.5±0.5mm Check Problem when if fails:
Turning shaft set (C=2.5±0.5mm) Malfunction of the
QH11D21A1Z0 Turning shaft set.
Solenoid bracket The tip of turning Jam
A shaft must not ← ←
stick out from
transfer face.
QH11
D21A1
D2-1
TMB6-9362
Confidential Page 120
機種 YUWF-10-ST/YUWF-11-ST
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 品質特性 備 考
度
PART No. STANDARD VALUE
3142 A
品 名 調 整 値 条 件 保守基準値 条 件 1238
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
31421238 ベルトテンション A=2.0 ± 0.3N 調整後、ベル QH11E2141Z0の位置
タイミングベルト B=3.5mm トを2,3回転さ で
C=(57.5)mm せテンション テンション調整を行う。
QH11D2191Z0 値の確認後、
モーターブラケット NGの場合再 未達成時の不具合:
度調整の事。 ・歯飛び
A ← ← ・プーリ、ベルトの摩耗
・寿命の低下
・負荷トルク増大
・ベルト外れ
・異音
31421238 Adjust the belt A=2.0 ± 0.3N After adjust, Perform the tension
Timing belt tension. B=3.5mm move the belt adjustment by
C=(57.5)mm a few laps. QH11E2141Z0
Then check
QH11D2191Z0 the belt Ploblem when if fails:
Motor bracket tension. If the ・Jumping timing belt.
A belt tension is ← ← ・Wear timing pullies
out of and timing belt.
tolerance ・Reduce life
range, adjust ・Increase load torque
the belt ・Detachment of timing
tension again. belt.
N i
QH11
D2191
D2-2
TMB6-9362
Confidential Page 121
機種 YUWF-10-ST/YUWF-11-ST
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
QH10
度
D1101
品 名 調 整 値 条 件 保守基準値 条 件
RANK
PART NAME
OBJECT
ASSEMBLING METHOD MAINTENANCE METHOD
REMARKS A
QH11E21A0Z0 取付位置 A方向にガタがあ 確認 未達成時の不具合:
ブンキジクセット る事。 ・分岐軸の渋りによる
QH10D1101Z0 ジャム
カップリング
A ← ←
E2-1
TMB6-9362
Confidential Page 122
機種 YUWF-10-ST/YUWF-11-ST
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度 QH11
RANK
品 名
OBJECT
調 整 値 条 件 保守基準値 条 件
REMARKS
E2141
A
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
31420944 ベルトテンション A=2.0 ± 0.3N 調整後、ベル QH11E2141Z0の位置
タイミングベルト B=1.5mm トを2,3回転さ で
C=(24.5)mm せテンション テンション調整を行う。
QH11E2141Z0 値の確認後、
モーターブラケット NGの場合再 未達成時の不具合:
度調整の事。 ・歯飛び
A 調整後にネ ← ← ・プーリ、ベルトの摩耗
ジロックの ・寿命の低下
事。 ・負荷トルク増大
・ベルト外れ
・異音
31420944 Adjust the belt A=2.0 ± 0.3N After adjust, Perform the tension
Timing belt tension. B=1.5mm move the belt adjustment by
C=(24.5)mm a few laps. QH11E2141Z0
QH11
Then check
E21E0
QH10C1051Z0 the belt Ploblem when if fails: 3142
Motor bracket tension. If the ・Jumping timing belt. 0944
A belt tension is ← ← ・Wear timing pullies
out of and timing belt.
tolerance ・Reduce life
range, adjust ・Increase load torque φ3
the belt ・Detachment of timing
tension agein. belt.
31421443 ベルトテンション D=2.0 ± 0.3N 調整後、ベル N i
QH11E21E0Z0の位置 D
タイミングベルト E=8mm トを2,3回転さ で
F=(140)mm せテンション テンション調整を行う。 3142
QH11E21E0Z0 値の確認後、 1443
アイドラプーリブラ NGの場合再 未達成時の不具合:
ケットセット 度調整の事。 ・歯飛び
A 調整後にネ ← ← ・プーリ、ベルトの摩耗
ジロックの ・寿命の低下
事。 ・負荷トルク増大
・ベルト外れ
・異音
31421443 Adjust the belt D=2.0 ± 0.3N After adjust, Perform the tension
Timing belt tension. E=8mm move the belt adjustment by
F=(140)mm a few laps. QH11E21E0Z0
QH11E21E0Z0 Then check
Idler pulley the belt Ploblem when if fails:
bracket set tension. If the ・Jumping timing belt.
A belt tension is ← ← ・Wear timing pullies
out of and timing belt.
tolerance ・Reduce life
range, adjust ・Increase load torque
the belt ・Detachment of timing E2-2
tension agein. belt. TMB6-9362
N i
Confidential Page 123
機種 YUWF-10-ST/YUWF-11-ST
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度
品 名 調 整 値 条 件 保守基準値 条 件
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
QH11E2351Z0 取付位置 ローラとソコイタセットが 確認 未達成時の不具合:
ホジョブラケット 面一になる位置で 開閉動作不良
3792T064 ホジョブラケットを固
A ローラ 定する ← ←
QH11Z11A0Z0
ソコイタセット
QH11E2351Z0 Attach position Fix the Bracket at Confirmation Possible problem:
Bracket the position where Opening and closing
3792T064 the roller and the operation failure
A ← ←
Roller Bottom plate set
QH11Z11A0Z0 are flush
Bottom plate set 3792
QH11E23A0Z0 取付位置 ホジョブラケット固定 確認 未達成時の不具合: T064
ベースブラケットセット 後の隙間(参考値)
QH11E21C0Z0 A=(10mm)
A マエソクバンセット ← ←
QH11
E23A0
QH11
E21C0
E2-3
TMB6-9362
Confidential Page 124
機種 YUWF-10-ST/YUWF-11-ST
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度
品 名 調 整 値 条 件 保守基準値 条 件
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
H4G0S2304Z0 取付位置 QH11Z12E0Z0と 調整 未達成時の不具合:
マグネットキャッチ QH11D24A1Z0の 外観不良
隙間
A A=2±0.5 ← ←
H4G0
S2304
QH11
D24A1
QH11
Z1211
A
Z2-1
TMB6-9362
Confidential Page 125
機種 YUWF-10-ST/YUWF-11-ST
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度
品 名 調 整 値 条 件 保守基準値 条 件
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD QH11 QH11
QH11Z1261Z0 取付位置 A=0~0.1mm 確認 未達成時の不具合: Z1261 E23A0
アテイタ 動作不良
QH11E23A0Z0
A ベースブラケットセット ← ←
Z2-2
TMB6-9362
Confidential Page 126
機種 YUWF-10-ST/YUWF-11-ST
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度
品 名 調 整 値 条 件 保守基準値 条 件 QH11
RANK OBJECT REMARKS D24A1
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
QH11Z1411Z0 取付位置 A=A'=(2mm) 確認 未達成時の不具合:
マエカバー 均等隙間のこと 外観不良
QH11D24A1Z0
A ウシロカバー ← ←
QH11
QH11Z1411Z0 Attach position Mounted closer Check Problem when it fails:
Z1411
Front cover to the B direction Assembly failure
QH11D1421Z0 (4 places)
A Left cover ← ←
QH11 B
Z1421
Z2-3
TMB6-9362
Confidential Page 127
機種 YUWF-10-ST/YUWF-11-ST
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度
品 名 調 整 値 条 件 保守基準値 条 件
RANK OBJECT REMARKS
PART NAME ASSEMBLING
METHOD MAINTENANCE METHOD
QH11Z1451Z0 取付位置 A方向に寄せて 確認 未達成時の不具合:
ウエカバー 取付け 外観不良
QH11D24A1Z0
A ウエカバー ← ←
A
QH11 QH11
Z1451 D24A1
Z2-4
TMB6-9362
Confidential Page 128
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度
品 名 調 整 値 条 件 保守基準値 条 件
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
QH10Z1106Z0 取付位置 基板を取り付けた 確認 未達成時の不具合:
キバンブラケット 状態で図の方向 部品破損
に当て付け
A ※スリット2箇所(差 --- ---
し込み)
QH10
Z1106
Abutting
TMB6-9362
Page 129
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度 BAT1
品 名 調 整 値 条 件 保守基準値 条 件 CPU+I/O-PC BOARD
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
QH10ZEA00Z0 DIPSW設定 図1の通り 電源OFF状 未達成時の不具合:
CPU+I/O-PC 態で実施す 予期せぬ動作不良
ASSY ること
A --- ---
SW2
QH10ZEA00Z0 Setting of DIP Set like Figure 1. Turn off the Problem when it
CPU+I/O-PC switch power fails:an unexpected
A ASSY (SW1-3) switch. --- --- error occurred SW1
QH10ZEA00Z0 Connect button Connect button Turn off the Problem when it
CNSD2
CPU+I/O-PC cell cell to BAT1 power fails:an unexpected
A ASSY switch. --- --- error occurred
TMB6-9362
Page 130
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度 MAINCPU(G-7355) BOARD
品 名 調 整 値 条 件 保守基準値 条 件 SW1
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
QH10ZE100Z0 リチウム一次電 CNBATに接続 電源OFF状 未達成時の不具合:
MAINCPU 池の接続 すること 態で実施す 予期せぬ動作不良
ASSY ること
A --- ---
QH10ZE100Z0 Connect lithium Connect lithium Turn off the Problem when it
MAINCPU primary battery primary battery power fails:an unexpected
A ASSY of switch. --- --- error occurred
the MAINCPU
BOARD to
CNBAT
QH10ZE100Z0 DIPSW設定 図1の通り 電源OFF状 未達成時の不具合:
MAINCPU 態で実施す 予期せぬ動作不良
ASSY ること
A --- ---
QH10ZE100Z0 Setting of DIP Set like Figure 1. Turn off the Problem when it
MAINCPU switch power fails:an unexpected
A ASSY (SW1) switch. --- --- error occurred
CNBAT
bit SW1
1 OFF
2 OFF
3 OFF
4 OFF
5 OFF
6 OFF
7 OFF
8 OFF
TMB6-9362
Page 131
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度 HP Sensor(PSA1) adjustment
品 名 調 整 値 条 件 保守基準値 条 件 HP sensor(PSA1)
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
QH10ZE200Z0 HPセンサ調整 RASにて調整 機内に紙幣 RAS仕様書参照
CTRL-U ASSY (PSA1) なきこと 未達成時の不具合:
--- HPセンサ動作不良
A ---
Sensor position
Show as ①Remove a dirt and dust of the PSA1 sensor top surface.
1. CONSTITUTION OF MACHINE - ②Place the HP sensor adjustment dummy on the PSA1 sensor.(※)
[LAYOUT OF SENSORS AND ACTUATORS] (Don't move until adjustment completion.)
③HP sensor adjustment by RAS.
RAS login→MACHIN RAS→Adjust Sensors→Hopper sensor
※Refer to "RAS specifications".
④After adjustment completion, remove the HP sensor adjustment dummy.
TMB6-9362
Confidential Page 132
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度
品 名 調 整 値 条 件 保守基準値 条 件
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
4L230208 取付位置 右図参照 確認 未達成時の不具合:
LCD ※ねじに当て付け
A=(4.5)
A ← ←
Abutting
※Both up and down
4L23
0208
QH10
Z1210
TMB6-9362
Page 133
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考 TP
度 MAINCPU(G-7355) BOARD
+24V
品 名 調 整 値 条 件 保守基準値 条 件
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
QH10ZE100Z0 Check +24V TP+24V +22.8V Problem when it
MAINCPU ⇔ ~ fails:an unexpected
ASSY TP1 or 2 +25.2V error occurred
A --- ---
TP
TP2 -12V
QH10ZE100Z0 Check +12V TP+12V +11.4V Problem when it (GND1)
MAINCPU ⇔ ~ fails:an unexpected
ASSY TP1 or 2 +12.6V error occurred
A --- ---
TMB6-9362
Page 134
機種 UW-F4 series
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度 CTRL-U(G-7356) BOARD
品 名 調 整 値 条 件 保守基準値 条 件
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD
TP TP TP
QH10ZE200Z0 Check +24V TP24V +22.8V Problem when it
~
3.3V -12V GND1A
CTRL-U ASSY ⇔ fails:an unexpected
TPGND1A +25.2V error occurred
A --- ---
or GND1B
TMB6-9362
Page 135
機種 YUWF-10-ST/YUWF-11-ST
QA表Ⅱ MODEL
注 記
重 品目コード 特 性 値
要 PART No.
品質特性 STANDARD VALUE
備 考
度 ST-V(G-7360) BOARD
品 名 調 整 値 条 件 保守基準値 条 件
RANK OBJECT REMARKS
PART NAME ASSEMBLING METHOD MAINTENANCE METHOD TP
QH10ZE500Z0 Check +12V TP12V +11.4V Problem when it 1.2V
ST-V ASSY ⇔ ~ fails:an unexpected
TPGND +12.6V error occurred
A --- ---
1-1
TP
-12V
QH10ZE500Z0 Check +5V TP5V +4.75V Problem when it
ST-V ASSY ⇔ ~ fails:an unexpected
A ---
TPGND +5.25V
---
error occurred TP
1-1 12V
TMB6-9362
Page 136
8. RAS SPECIFICATIONS
9. TROUBLE SHOOTING
A:繰出し部
FEED UNIT
A A
PSA2
LDA2
札高さ検知 ST3582
G3582
(遠)
札押さえ上位置検知 札押さえ位置検知
ZHR-3
ZHR-3
B PIA3 PIA2 B
KI1365-GR02LF KI1365-GR02LF
ZHR-5 ZHR-5
(近) (近)
C C
D D
AH200 AH700
札押え駆動
CNA2 CNA20 CNA20 CNA17 CNA17
DMA1
M TZ040E
E B26B-PUDSS-1(LF)(SN) PUDP-26V-S DF1B-26DES-2.5RC DF1B-26DEP-2.5RC SMP-02V-NC SMR-02V-N E
NF70AHA00Z0流用
繰出し搬送駆動 繰出し駆動
BMA2 BMA1
M 48M053K010 M 48M053K010
PAP-11V-S PAP-11V-S
F F
前扉部へ
for LCD UNIT
上部前扉セット検知
AH800
CNA30 CNA30 PIZ1
KI1365-GR02LF
G G
AH300
CNA3 CNA32 CNA32
FAN2
FAN D06A-24TUB(K)
504187-1870 504186-1800 SMP-03V-NC SMR-03V-N
CNA4
B16B-PUDSS-1(LF)(SN)
CNA31 CNA3
SWZ2
H SDK-1-2 札押さえSW H
SMP-02V-NC SMR-02V-N
DATE DESIGN DRAW MODEL PAGE
JB50AH300Z0流用 2016-03-08 MAEDA UTO UW-X 1/7
CTRL_U
G-7356
Manual
Number TMB69362
Circuit
Name Wiring Diagram
1 2 3 4 5 6 7 8 9 10 11 12
C:RJ搬送部
CH300 CH600 RJ TRANSPORT UNIT
CNC1 CNC10 CNC10 CN1 LED
抜取り通知LED
A G-7034 LEDC1 A
504187-4070 504186-4000 504186-1600 505265-1600 PAP-02V-S SM02B-PASS-TBT(LF)(SN)
紙幣通過検知1S 紙幣通過検知1C
(BV後) (BV後)
LDC1S LDC1C
C G3582 G3582 C
ZHR-3 ZHR-3
(近) (近)
PSC1S PSC1C
ST3582 ST3582
CH400 CH700
ZHR-3 ZHR-3
CNC2 CNC20 CNC20
SMR-05V-N SMP-05V-NC
CH500 CH800
CNC3 CNC30 CNC30
BMC1
M RJ搬送駆動
E 48M053K010 E
B24B-PUDSS-1(LF)(SN) PUDP-24V-S DF1B-24DEP-2.5RC DF1B-24DES-2.5RC PAP-11V-S
SMC1
SM KH42HM2B115羽根車駆動
PHR-11
CNC31 4S020121
RSC1
SD RSE32/47-C038 RJ搬送分岐
SMP-02V-NC SMR-02V-N
CNC32 4S020121
RSC2
SD RSE32/47-C038 拡張分岐
F SMP-02V-NC SMR-02V-N F
CH900
FGC1 FGC2
SRA-21T-3 FN1.25-M3
CH100
G FGC3 G
CNU1 CNMN1
SRA-21T-3
CH200
CNU2 CNMN2
H H
DATE DESIGN DRAW MODEL PAGE
MAINCPU CTRL_U
2016-03-08 MAEDA UTO UW-X 2/7
G-7355 G-7356
Manual
Number TMB69362
Circuit
Name C部(RJ TRANSPORT UNIT)
H
G
F
E
D
C
B
A
1
G-7355
MAINCPU
B13B-PASK-N(LF)(SN)
CND3
B08B-PASK-N(LF)(SN)
CND2
504187-4070
CND1
DH300
DH200
DH100
PAP-13V-S
PAP-08V-S
2
504186-4000
PID1
STLD
G-7380
SRA-21T-3
FGD1
KI1365-GR02LF
上部セット検知
SRA-21T-3
FGD2
BM04B-GHS-TBT(LF)(SN)
CNST1
ZHR-5
3
DH400 DH500
GHR-04V-S
PAP-11V-S
SMR-11V-N SMP-11V-NC SMP-09V-NC SMR-09V-N
GHR-04V-S
M
BMD1
48M053K010
CNST1
4
STLD
中間搬送駆動
G-7380
BM04B-GHS-TBT(LF)(SN)
5
DH600
CND10 CND10
SMR-05V-N SMP-05V-NC
ST3582
PSD1S
ST3582
PSD1C
G3582
LDD1C
G3582
LDD1S
4S020121 紙幣通過検知1C
CND20
RSD1 (スタッカ1前)
SD (近)
6
RSE32/47-C038
SMP-02V-NC SMR-02V-N スタッカ1分岐
SRA-21T-3
FGD3
紙幣通過検知1S
(スタッカ1前)
(近)
DH700
CND11 CND11
SMR-05V-N SMP-05V-NC
DH900
ST3582
PSD2S
ST3582
PSD2C
G3582
LDD2C
G3582
LDD2S
7
4S020121 紙幣通過検知2C
CND21
RSD2 (スタッカ1入口)
SD RSE32/47-C038 (近)
FGD4
SMP-02V-NC SMR-02V-N スタッカ2分岐
紙幣通過検知2S
(スタッカ1入口)
SRA-21T-3
(近)
SMR-05V-N SMP-05V-NC
ST3582
PSD3S
ST3582
PSD3C
G3582
LDD3C
G3582
LDD3S
Number
Manual
DATE
4S020121 紙幣通過検知3C
CND22
RSD3 (スタッカ2入口)
SD RSE32/47-C038 (近)
SMP-02V-NC SMR-02V-N スタッカ3分岐
紙幣通過検知3S
(スタッカ2入口)
MAEDA
TMB69362
DESIGN
(近)
9
SMR-05V-N SMP-05V-NC
ST3582
PSD4S
ST3582
PSD4C
G3582
LDD4C
G3582
LDD4S
Name
Circuit
紙幣通過検知4C
(スタッカ3入口)
(近)
10
紙幣通過検知4S
(スタッカ3入口)
(近)
UW-X
SMR-05V-N SMP-05V-NC
ST3582
PSD5S
ST3582
PSD5C
G3582
LDD5C
G3582
LDD5S
ZHR-3 ZHR-3
11
ZHR-3 ZHR-3
紙幣通過検知5C
(スタッカ4入口)
(近)
紙幣通過検知5S
(スタッカ4入口)
D:中間搬送部
D部(TRANSPORT 1 UNIT)
(近)
3/7
PAGE
12
TRANSPORT 1 UNIT
H
G
F
E
D
C
B
A
1 2 3 4 5 6 7 8 9 10 11 12
CNE1 EH100
E:スタッカ部
504187-2670 504186-2600 STACKER UNIT
CNE2
A A
504187-2870 504186-2800
CNE3
504187-3070 504186-3000
CNE4
504187-3270 504186-3200
CNE5 EH200
B B26B-PUDSS-1(LF)(SN) PUDP-26V-S B
EH400
CNE50 CNE50 CNE50 CNE50
QH10EH400Z0流用 QH10EH400Z0流用 QH10EH400Z0流用
SMR-09V-N SMR-09V-N SMR-09V-N SMR-09V-N
FGE10 FGE20 FGE30 FGE40
FN1.25-M3 FN1.25-M3 FN1.25-M3 FN1.25-M3
羽根車駆動 羽根車駆動 羽根車駆動 羽根車駆動
C SME1 SME2 SME3 SME4 C
KH42HM2B115 SM KH42HM2B115 SM KH42HM2B115 SM KH42HM2B115 SM
505265-2600
505265-2600
505265-2600
505265-2600
PHR-11 PHR-11 PHR-11 PHR-11
CNE20
CNE30
CNE40
SRA-21T-3 SRA-21T-3 SRA-21T-3 SRA-21T-3
504186-2600
CNE10
504186-2600
CNE10
504186-2600
CNE10
504186-2600
D D
羽根車回転検知 羽根車回転検知
羽根車回転検知 羽根車回転検知
PIE3 PIE4
PIE1 PIE2
KI1365-GR02LF KI1365-GR02LF
KI1365-GR02LF KI1365-GR02LF
ZHR-5 ZHR-5
ZHR-5 ZHR-5
E 504193-0400 504195-0470 504195-0570 504193-0500 504193-0400 504195-0470 504195-0570 504193-0500 504193-0400 504195-0470 504195-0570 504193-0500 504193-0400 504195-0470 504195-0570 504193-0500 E
Manual
Number TMB69362
Circuit
Name E部(STACKER UNIT)
1 2 3 4 5 6 7 8 9 10 11 12
FGZ1 FGZ2
SRA-21T-3 SRA-21T-3
A A
CNBL
B2P-VH(LF)(SN) VHR-2N
4W900331
CNLVD CNL1C CNDFS CN1
B B
ZH100
CNPC1 CNPW
CNLI CNLO LCD
+24 → +12V(for LCD) キョウセラ
55917-1030 51353-1000 51353-1000 55917-1030
PAP-04V-S SM04B-PASS-TBT(LF)(SN) 504195-0870 504193-0800 TCG104SVLPAAFA-AA20
B-LIGHT 10.4インチSVGA
G-7357 タッチパネル付
ZH200
ZH800
CNPC2 CNRC
CNZ CNZ
C USB_I/F CN4 C
B05B-PASK-N(LF)(SN) PAP-05V-S PAP-06V-S B06B-PASK-N(LF)(SN)
DF1B-12DEP-2.5RC DF1B-12DES-2.5RC タッチパネルコントローラボード
S5B-PH-K-S(LF)(SN)
CNSD2
CNRA
SDK-9BNS-K13-GS-TB(LF)(SN
MJ-66J-RD315(LF)(SN)
CNRB
I/F RS232C X 3
CN1 CN1
MJ-66J-RD315(LF)(SN)
FGZ3
61082-181409LF 61083-184409LF SRA-21T-3 CNROP
F F
ZH600
CNIF CNIF MJ-66J-RD315(LF)(SN)
CN2 CN2
HVD-310 HVD-310_OP
G USB2_TypeMini-B CNUSB G
UB-M5BR-S14-4S(LF)(SN) ZHA00
CNOPU CNOP1
CNIFS
B20B-PUDSS-1(LF)(SN) PUDP-20V-S
504186-3000 504189-3070
H BVCPU HVD-310_op H
MAINCPU
G-7234 G-XXXX DATE DESIGN DRAW MODEL PAGE
G-7355 2016-03-08 MAEDA UTO UW-X 5/7
Manual
Number TMB69362
Circuit
Name LCD
1 2 3 4 5 6 7 8 9 10 11 12
A PHA00 A
CN4 CN4
FGZ5
緑
SRT-51T-3FE
FGZ1 緑/黄
ELR-02V シロイロ ELP-02V シロイロ
SRT-51T-4FE
緑/黄 FGZ3
SRT-51T-3FE
NF1-E STO-61T-250N
B2P3-VH(LF)(SN) VHR-3N
PH500
CNAC3
緑 FGZ4
C SRT-51T-4FE C
B2P3-VH(LF)(SN) VHR-3N
AC-DIV
G-7358
PH700
DC POWER SUPPLY
PHB00 CN1 CN2 CNPW2
MEAN WELL
CN6 CN6
緑/黄 FGZ2 EPS-15-5
緑/黄 SRT-51T-3FE VHR-5N B3P5-VH(LF)(SN) B2P-VH(LF)(SN) VHR-2N VHR-2N B2P-VH(LF)(SN)
ELP-02V シロイロ ELR-02V シロイロ
IN:AC100-240V
OUT:DC5V
15W
D D
E E
PH800
空冷ファン
CNFAN
FAN1
D06A-24TUB(K) FAN
PAP-06V-S B06B-PASK-N(LF)(SN)
オプションへ
CNACOUT
◎縦型スタッカ
F F
◎反転ユニット ELR-03V シロイロ
◎帯封ユニット(UW-X2)
G G
MAINCPU
G-7355
H H
DATE DESIGN DRAW MODEL PAGE
2016-03-08 MAEDA UTO UW-X 6/7
Manual
Number TMB69362
Circuit
Name POWER SUPPLY UNIT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
増設スタッカ進入
紙幣通過検知C
FN1.25-M3
505265-2200
RSE32/47-C038
RSE32/47-C038
LDD8C 4S020121 CND21
SMR-05V-N
FGE1
RSD5
EH200 G3582 SD
CNTX USS-TX USS-RX CNRX ZHR-3
DH100
CND11
ZH300
CNZ21
SD
G-7364 G-7365 FGE2 (近) SMR-02V-N SMP-02V-NC
SRA-21T-3
504193-0500 504195-0570 504195-0470 504193-0400 PSD8C BMD2
SMR-02V-N
横搬送駆動
4S020121
ST3582 48M053K010
FGE3
ZHR-3
残留検知 羽根車駆動 SRA-21T-3 スタッカ5入口 DH200
CND11
SMP-05V-NC
CNZ21
504186-2200
M
USE5 SME5 紙幣通過検知S CND31 CND31
SM PAP-11V-S
C KH42HM2B115 LDD8S
C
PHR-11
G3582
ZHR-3 SMR-10V-N SMP-10V-NC
CND41
SMP-02V-NC
SRA-21T-3
(近)
E:スタッカ部 QH11EH100Z0流用
残留検知 残留検知 PSD8S CNDS1
FGZ7
ST3582
LDE6B LDE6A
ZHR-3
G3582 G3582 504186-2200 504189-2270
ZHR-3 ZHR-3
(遠) (遠)
PSE6B PSE6A スタッカ6入口 CNDS2
ST3582 ST3582 紙幣通過検知C
LDD9C
ZHR-3 ZHR-3 CNE11 CNE12 504186-2000 504189-2070
FN1.25-M3
ST3582
ソレノイド
ZHR-3
スタッカ6入口 DH300
FGE1
FGZ6
SRA-21T-3
RSE32/47-C038
CNTX USS-TX USS-RX CNRX
紙幣通過検知S CND32 CND32
G-7364 G-7365
RSD6
FGE2
LDD9S
SD
SRA-21T-3
504193-0500 504195-0570 504195-0470 504193-0400 G3582
FGE3 ZHR-3 SMR-05V-N SMP-05V-NC
SRA-21T-3 (近)
SMR-02V-N
4S020121
残留検知 羽根車駆動 QH11EH200Z0流用
PSD9S
USE6 SME6 SM ST3582
KH42HM2B115
E PHR-11 ZHR-3 E
E:スタッカ部 QH11EH100Z0流用
CND42
SMP-02V-NC
残留検知 残留検知
FN1.25-M3
ST3582
ZHR-3
FGE1
スタッカ7分岐 スタッカ7入口
CNTX USS-TX USS-RX CNRX
ソレノイド 紙幣通過検知S
FGE2 CND32 CND33
G-7364 G-7365
SRA-21T-3 LDD10S
RSE32/47-C038
504193-0500 504195-0570 504195-0470 504193-0400 G3582
FGE3 ZHR-3 SMR-05V-N SMP-05V-NC
RSD7
SD
SRA-21T-3 (近)
残留検知 羽根車駆動 QH11EH200Z0流用
PSD10S
USE7 SME7
SMR-02V-N
SM ST3582
4S020121
KH42HM2B115
PHR-11 ZHR-3
G G
E:スタッカ部 QH11EH100Z0流用
残留検知 残留検知
CND43
SMP-02V-NC
LDE8B LDE8A
QH11DH300Z0流用
G3582 G3582
ZHR-3 ZHR-3 CNDS1
(遠) (遠) スタッカ8入口
PSE8B PSE8A
紙幣通過検知C
ST3582 ST3582
LDD11C 504186-2200 504189-2270
ZHR-3 ZHR-3 CNE11 CNE14 G3582
ZHR-3 CNDS2
(近)
縦搬送駆動
DF1B-14DEP-2.5RC DF1B-14DES-2.5RC PSD11C
48M053K010
504189-2070
FN1.25-M3
ST3582
BMD3
H DISP H
M
ZHR-3 G-7362
FGE1
スタッカ8入口
CNTX USS-TX USS-RX CNRX FGE2 紙幣通過検知S CND32 CND34
G-7364 G-7365 SRA-21T-3 LDD11S 前扉セット検知
PIZ2
PAP-11V-S
G3582
504193-0500 504195-0570 504195-0470 504193-0400 FGE3 ZHR-3 SMR-05V-N SMP-05V-NC
KI1365-GR02LF
SRA-21T-3 (近)
QH11EH200Z0流用 ZHR-5
残留検知 羽根車駆動 PSD11S
USE8 SME8 SM ST3582
KH42HM2B115 PHR-11 ZHR-3
J J
504186-3800
504186-3400
504186-3200
504186-2000
PUDP-26V-S
PUDP-20V-S
PUDP-16V-S
PUDP-14V-S
PAP-08V-S
ZH800
ZH700
ZH600
ZH500
ZH400
ZH200
ZH100
CNE3
B26B-PUDSS-1(LF)(SN)
CNE2
504187-3870
CNE1
504187-3470
CND4
B20B-PUDSS-1(LF)(SN)
CND3
504189-3070
CND2
B16B-PUDSS-1(LF)(SN)
CND1
B14B-PUDSS-1(LF)(SN)
CNZ2
504187-2070
CNZ1
B08B-PASK-N(LF)(SN)
CNE3
B26B-PUDSS-1(LF)(SN)
CNE2
504187-3870
CNE1
504187-3470
CND4
B20B-PUDSS-1(LF)(SN)
CND3
504189-3070
CND2
B16B-PUDSS-1(LF)(SN)
CND1
B14B-PUDSS-1(LF)(SN)
CNZ2
504187-2070
CNZ1
B08B-PASK-N(LF)(SN)
CNE3
B26B-PUDSS-1(LF)(SN)
CNE2
504187-3870
CNE1
504187-3470
CND4
B20B-PUDSS-1(LF)(SN)
CND3
504187-3270
CND2
B16B-PUDSS-1(LF)(SN)
CND1
B14B-PUDSS-1(LF)(SN)
CNZ2
504187-2070
CNZ1
B08B-PASK-N(LF)(SN)
B05B-PASK-N(LF)(SN)
B05B-PASK-N(LF)(SN)
B05B-PASK-N(LF)(SN)
B10P-VH(LF)(SN)
B10P-VH(LF)(SN)
B10P-VH(LF)(SN)
B9P-VH(LF)(SN)
B9P-VH(LF)(SN)
B9P-VH(LF)(SN)
504187-2870
504187-2870
504187-2870
K K
53398-1171
53398-1171
53398-1171
CNST1
CNFPG
CNMN1
CNPW1
CNPW2
CNST1
CNFPG
CNMN1
CNPW1
CNPW2
CNST1
CNFPG
CNMN1
CNPW1
CNPW2
ST-V ST-V ST-V
G-7360 G-7360 G-7360
504186-2800
PAP-05V-S
VHR-9N
504186-2800
VHR-10N
VHR-9N
504186-2800
VHR-10N
ZHC00
VHR-9N
PH300
VHR-10N
PH200
QH10PHA00Z0流用
DC POWER SUPPLY
ZHD00 本体部 CN81
TDK-Lambda
CNPW CNPW CNPW CNPW CNPW OP-IF MAINCPU
ZH900 CNOP1 RWS600B-24/R
G-7361 G-7355
PHDR-10VS S10B-PHDSS(LF)(SN)
ELR-09V シロイロ ELP-09V シロイロ ELR-09V シロイロ QH11ZHC00Z0流用 ELP-09V シロイロ ELR-09V シロイロ ACN
504186-2800 504187-2870 N1.25-5 N
ELP-02V シロイロ
ZHE00
SRT-51T-3FE
L +V1 ~ +V4 L
CNOP32 CNOP32 CNOP32 CNOP21 CNOP21 ZHA00 CNOP2 +V
L ACL for UW-F4
CNOP CNOP
CN4
N1.25-5 ACFG
IN:AC100-240V
FG2
505265-3000 504186-3000 505265-3000 504186-3000 505265-3000 504186-3200 504187-3270 FG
ZHF00 -V1 ~ -V4 FG1
-V OUT:DC24V SRA-51T-3.7
CNOP31 CNOP31 CNOP31 ZHB00 CNOP3 DY11-100S-4 DY01-100S SRT-51T-3FE
600W SRA-51T-3.7
SRA-51T-3.7
ELR-02V シロイロ
CN4
504186-3200 504186-3200 505265-3200 504186-3400 504187-3470
DATE DESIGN DRAW MODEL PAGE
QH11ZHC00Z0流用
CNOP4 2016-03-08 MAEDA UTO UW-X 7/7
QH11ZHD00Z0流用
QH11ZHE00Z0流用
M QH11ZHF00Z0流用 504187-3670
Manual
Number TMB69362
Circuit
Name YUW-10/11-ST M
Page 144
IO-PC(G-6957)ASSY
CNIF
CNLVD
CNLAN
LCD UNIT
connector CNLCD
CNSW
CNSD1
MAINCPU
connectors
CNSD2
CNPW CNRC
CTRL-U(G-7356)ASSY
CNC1
CNA1
HP UNIT CNC2
connector
CNA2
MAINCPU RJ UNIT
connectors connector CNC3
CNMN2 CNMN1
MAINCPU(G-7355)ASSY
CNSW CNPC1 CNPC2 CNBV CNU2 CNU1 CNE1 CNE2 CNE3 CNE4
CNBL
CNPW1 CNPW2
ST-V(G-7360)ASSY
CNE1
CNZ1
CNE2
Parts code
Unit Name Board Name Board No. Compatible Model
Restriction
RJ TRANSPORT NF70DE100Z0
LED BOARD G-7034 UHS-10,USF-200
UNIT Nothing
-
other BOARD Compatible Board is nothing
-
Parts code
Unit Name Parts Name Compatible Model
Restriction
4B000138
CABINET UNIT FUSE UHS-10,USF-200
-
PCB ASSY:CONTROL 4Z591424
(LCD) UHS-10,USF-200
(TPC BOARD) -
-
other Parts Compatible Parts are nothing
-
SETTING LIST
Calibrating
BOARD NAME Software update Sensors adjustment
the touch panel
CPU+I/O-PC BOARD ○ ○
CTRL-U BOARD ○
MAINCPU BOARD ○ ○
LCD ○
TPC BOARD ○
INTERNAL SD CARD ○
ST-V BOARD ○
※TPC=touch panel controller
・ Software update
Refer to "HOW TO INSTALL A SOFTWARE".
・ Sensors adjustment
Execute RAS [ Adjust sensors ].
Refer to "RAS SPECIFICATIONS".