Professional Documents
Culture Documents
4M16 HILTI fail
4M16 HILTI fail
0
Company: PT. Whidia Bharaya Page: 1
Specifier: Engineer Project: Colo HCPT rev.6
Address: JL. Katalia I no. 20, Palmerah, Jak-Bar Sub-Project I Pos. No.: Rumah Makan Mutiara
Phone I Fax: 021-565 5775 | 021-565 5775 Date: 25/06/2024
E-Mail: admin@whidia-bharaya.co.id
1 Input data
Anchor type and diameter: HIT-RE 500 V3 + HAS-U 5.8 M16
Effective embedment depth: hef,act = 216 mm (hef,limit = - mm)
Material: 5.8
Evaluation Service Report: ESR-3814
Issued I Valid: 1/1/2020 | 1/1/2021
Proof: Design method ACI 318-14 / Chem
Stand-off installation: eb = 0 mm (no stand-off); t = 20 mm
Anchor plate: lx x ly x t = 200 mm x 200 mm x 20 mm; (Recommended plate thickness: not calculated
Profile: Flat bar, 100 x 10; (L x W x T) = 100 mm x 10 mm
Base material: cracked concrete, , fc' = 2,611 psi; h = 340 mm, Temp. short/long: 30/30 °C
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: tension: condition B, shear: condition B; no supplemental splitting reinforcement present
edge reinforcement: none or < No. 4 bar
R
- The anchor calculation is based on a rigid anchor plate assumption.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.html Profis Anchor 2.9.0
Company: PT. Whidia Bharaya Page: 2
Specifier: Engineer Project: Colo HCPT rev.6
Address: JL. Katalia I no. 20, Palmerah, Jak-Bar Sub-Project I Pos. No.: Rumah Makan Mutiara
Phone I Fax: 021-565 5775 | 021-565 5775 Date: 25/06/2024
E-Mail: admin@whidia-bharaya.co.id
Anchor forces are calculated based on the assumption of a rigid anchor plate.
3 Tension load
Load Nua [kN] Capacity f Nn [kN] Utilization bN = Nua/f Nn Status
Steel Strength* 11.225 51.025 22 OK
Bond Strength** 44.901 73.818 61 OK
Sustained Tension Load Bond Strength* N/A N/A N/A N/A
Concrete Breakout Strength** 44.901 54.953 82 OK
* anchor having the highest loading **anchor group (anchors in tension)
Variables
Ase,N [mm2] futa [N/mm2]
157 500.00
Calculations
Nsa [kN]
78.500
Results
Nsa [kN] f steel f Nsa [kN] Nua [kN]
78.500 0.650 51.025 11.225
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.html Profis Anchor 2.9.0
Company: PT. Whidia Bharaya Page: 3
Specifier: Engineer Project: Colo HCPT rev.6
Address: JL. Katalia I no. 20, Palmerah, Jak-Bar Sub-Project I Pos. No.: Rumah Makan Mutiara
Phone I Fax: 021-565 5775 | 021-565 5775 Date: 25/06/2024
E-Mail: admin@whidia-bharaya.co.id
Nag = (AA ) y
Na
Na0
ec1,Na y ec2,Na y ed,Na y cp,Na Nba ACI 318-14 Eq. (17.4.5.1.b)
f Nag ≥ Nua ACI 318-14 Table 17.3.1.1
ANa = see ACI 318-14, Section 17.4.5.1, Fig. R 17.4.5.1(b)
ANa0 = (2 cNa)2 ACI 318-14 Eq. (17.4.5.1c)
cNa = 10 da √ t uncr
1100
ACI 318-14 Eq. (17.4.5.1d)
( )
1
y ec,Na = e' ≤ 1.0 ACI 318-14 Eq. (17.4.5.3)
1+ N
cNa
y ed,Na = 0.7 + 0.3 ( ) ca,min
cNa
≤ 1.0 ACI 318-14 Eq. (17.4.5.4b)
y cp,Na = MAX ( )
ca,min cNa
,
cac cac
≤ 1.0 ACI 318-14 Eq. (17.4.5.5b)
Nba = l a · t k,c · p · da · hef ACI 318-14 Eq. (17.4.5.2)
Variables
2 2
t k,c,uncr [N/mm ] da [mm] hef [mm] ca,min [mm] aoverhead t k,c [N/mm ]
15.37 16 216 160 1.000 8.76
ec1,N [mm] ec2,N [mm] cac [mm] la
0 0 515 1.000
Calculations
cNa [mm] ANa [mm2] ANa0 [mm2] y ed,Na
227 269,357 205,592 0.912
y ec1,Na y ec2,Na y cp,Na Nba [kN]
1.000 1.000 1.000 95.075
Results
Nag [kN] f bond f Nag [kN] Nua [kN]
113.566 0.650 73.818 44.901
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.html Profis Anchor 2.9.0
Company: PT. Whidia Bharaya Page: 4
Specifier: Engineer Project: Colo HCPT rev.6
Address: JL. Katalia I no. 20, Palmerah, Jak-Bar Sub-Project I Pos. No.: Rumah Makan Mutiara
Phone I Fax: 021-565 5775 | 021-565 5775 Date: 25/06/2024
E-Mail: admin@whidia-bharaya.co.id
Ncbg = (AA ) y
Nc
Nc0
ec,N y ed,N y c,N y cp,N Nb ACI 318-14 Eq. (17.4.2.1b)
f Ncbg ≥ Nua ACI 318-14 Table 17.3.1.1
ANc see ACI 318-14, Section 17.4.2.1, Fig. R 17.4.2.1(b)
ANc0 = 9 h2ef ACI 318-14 Eq. (17.4.2.1c)
( )
1
y ec,N = 2 e'N ≤ 1.0 ACI 318-14 Eq. (17.4.2.4)
1+
3 hef
y ed,N = 0.7 + 0.3 (
ca,min
1.5hef )
≤ 1.0 ACI 318-14 Eq. (17.4.2.5b)
y cp,N = MAX (
ca,min 1.5hef
cac
,
cac )
≤ 1.0 ACI 318-14 Eq. (17.4.2.7b)
1.5
Nb = kc l a √fc hef
'
ACI 318-14 Eq. (17.4.2.2a)
Variables
hef [mm] ec1,N [mm] ec2,N [mm] ca,min [mm] y c,N
216 0 0 160 1.000
Calculations
ANc [mm2] ANc0 [mm2] y ec1,N y ec2,N y ed,N y cp,N Nb [kN]
436,832 419,904 1.000 1.000 0.848 1.000 95.817
Results
Ncbg [kN] f concrete f Ncbg [kN] Nua [kN]
84.543 0.650 54.953 44.901
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.html Profis Anchor 2.9.0
Company: PT. Whidia Bharaya Page: 5
Specifier: Engineer Project: Colo HCPT rev.6
Address: JL. Katalia I no. 20, Palmerah, Jak-Bar Sub-Project I Pos. No.: Rumah Makan Mutiara
Phone I Fax: 021-565 5775 | 021-565 5775 Date: 25/06/2024
E-Mail: admin@whidia-bharaya.co.id
4 Shear load
Load Vua [kN] Capacity f Vn [kN] Utilization bV = Vua/f Vn Status
Steel Strength* 3.025 28.200 11 OK
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout Strength (Concrete Breakout 12.098 118.360 11 OK
Strength controls)**
Concrete edge failure in direction y-** 12.098 25.594 48 OK
* anchor having the highest loading **anchor group (relevant anchors)
Variables
Ase,V [mm2] futa [N/mm2]
157 500.00
Calculations
Vsa [kN]
47.000
Results
Vsa [kN] f steel f Vsa [kN] Vua [kN]
47.000 0.600 28.200 3.025
( )
1
y ec,N = 2 e'N ≤ 1.0 ACI 318-14 Eq. (17.4.2.4)
1+
3 hef
y ed,N = 0.7 + 0.3 (
ca,min
1.5hef )
≤ 1.0 ACI 318-14 Eq. (17.4.2.5b)
y cp,N = MAX (
ca,min 1.5hef
cac
,
cac )
≤ 1.0 ACI 318-14 Eq. (17.4.2.7b)
1.5
Nb = kc l a √fc hef
'
ACI 318-14 Eq. (17.4.2.2a)
Variables
kcp hef [mm] ec1,N [mm] ec2,N [mm] ca,min [mm]
2 216 0 0 160
Calculations
ANc [mm2] ANc0 [mm2] y ec1,N y ec2,N y ed,N y cp,N Nb [kN]
436,832 419,904 1.000 1.000 0.848 1.000 95.817
Results
Vcpg [kN] f concrete f Vcpg [kN] Vua [kN]
169.086 0.700 118.360 12.098
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.html Profis Anchor 2.9.0
Company: PT. Whidia Bharaya Page: 6
Specifier: Engineer Project: Colo HCPT rev.6
Address: JL. Katalia I no. 20, Palmerah, Jak-Bar Sub-Project I Pos. No.: Rumah Makan Mutiara
Phone I Fax: 021-565 5775 | 021-565 5775 Date: 25/06/2024
E-Mail: admin@whidia-bharaya.co.id
Vcbg = (AA ) y
Vc
Vc0
ec,V y ed,V y c,V y h,V y parallel,V Vb ACI 318-14 Eq. (17.5.2.1b)
f Vcbg ≥ Vua ACI 318-14 Table 17.3.1.1
AVc see ACI 318-14, Section 17.5.2.1, Fig. R 17.5.2.1(b)
AVc0 = 4.5 c2a1 ACI 318-14 Eq. (17.5.2.1c)
( )
1
y ec,V = 2e'v ≤ 1.0 ACI 318-14 Eq. (17.5.2.5)
1+
3ca1
y ed,V = 0.7 + 0.3 (ca2
1.5ca1 )
≤ 1.0 ACI 318-14 Eq. (17.5.2.6b)
y h,V = √
1.5ca1
ha
≥ 1.0 ACI 318-14 Eq. (17.5.2.8)
(( ) )
0.2
l 1.5
Vb = 7 e √da l a √f'c ca1 ACI 318-14 Eq. (17.5.2.2a)
da
Variables
ca1 [mm] ca2 [mm] ecV [mm] y c,V ha [mm]
160 350 0 1.000 340
Calculations
AVc [mm2] AVc0 [mm2] y ec,V y ed,V y h,V Vb [kN]
139,200 115,200 1.000 1.000 1.000 30.259
Results
Vcbg [kN] f concrete f Vcbg [kN] Vua [kN]
36.563 0.700 25.594 12.098
6 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.).
This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is
assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum
required anchor plate thickness with FEM to limit the stress of the anchor plate based on the assumptions explained above. The proof if the
rigid anchor plate assumption is valid is not carried out by PROFIS Anchor. Input data and results must be checked for agreement with the
existing conditions and for plausibility!
• Condition A applies when supplementary reinforcement is used. The Φ factor is increased for non-steel Design Strengths except Pullout
Strength and Pryout strength. Condition B applies when supplementary reinforcement is not used and for Pullout Strength and Pryout
Strength. Refer to your local standard.
• Design Strengths of adhesive anchor systems are influenced by the cleaning method. Refer to the INSTRUCTIONS FOR USE given in the
Evaluation Service Report for cleaning and installation instructions
• Checking the transfer of loads into the base material and the shear resistance are required in accordance with ACI 318 or the relevant
standard!
• Installation of Hilti adhesive anchor systems shall be performed by personnel trained to install Hilti adhesive anchors. Reference ACI 318-14,
Section 17.8.1.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.html Profis Anchor 2.9.0
Company: PT. Whidia Bharaya Page: 7
Specifier: Engineer Project: Colo HCPT rev.6
Address: JL. Katalia I no. 20, Palmerah, Jak-Bar Sub-Project I Pos. No.: Rumah Makan Mutiara
Phone I Fax: 021-565 5775 | 021-565 5775 Date: 25/06/2024
E-Mail: admin@whidia-bharaya.co.id
7 Installation data
Anchor plate, steel: - Anchor type and diameter: HIT-RE 500 V3 + HAS-U 5.8 M16
Profile: Flat bar, 100 x 10; (L x W x T) = 100 mm x 10 mm Installation torque: 0.080 kNm
Hole diameter in the fixture: df = 18 mm Hole diameter in the base material: 18 mm
Plate thickness (input): 20 mm Hole depth in the base material: 216 mm
Recommended plate thickness: not calculated Minimum thickness of the base material: 252 mm
Drilling method: Hammer drilled
Cleaning: Compressed air cleaning of the drilled hole according to
instructions for use is required
100 100
50
100
3 4
100
x
100
1 2
50
50 100 50
Coordinates Anchor mm
Anchor x y c-x c+x c-y c+y
1 -50 -50 - 450 160 -
2 50 -50 - 350 160 -
3 -50 50 - 450 260 -
4 50 50 - 350 260 -
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.html Profis Anchor 2.9.0
Company: PT. Whidia Bharaya Page: 8
Specifier: Engineer Project: Colo HCPT rev.6
Address: JL. Katalia I no. 20, Palmerah, Jak-Bar Sub-Project I Pos. No.: Rumah Makan Mutiara
Phone I Fax: 021-565 5775 | 021-565 5775 Date: 25/06/2024
E-Mail: admin@whidia-bharaya.co.id
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan