Professional Documents
Culture Documents
JS8
JS8
JS8
JS8-无钥匙进入和无钥匙启动
1 左后门状态 Left rear door status 24 左前转向灯 Left front turning light
2 右后门状态 Right rear door status 25 高位刹车灯 High-mount brake light
3 尾门状态 Tail door status 27 副驾驶门状态 Passenger seat door status
4 机械钥匙解锁开关 Mechanical key unlock switch 28 迎宾灯输出 Welcome light output
5 尾门解锁开关 Tail door unlock switch 31 前雨刮高速继电器 Front wiper high-speed relay
6 后视镜折叠打开 Rearview mirror folds open 34 LIN1 LIN1
7 主驾门锁反馈 Driver side door lock feedback 35 右前转向灯 Right front turning light
8 信号地4 Signal grounding 36 倒车灯 Reverse light
11 后雾灯 Rear foglight 37 碰撞信号 Collision signal
12 内顶灯 Internal roof light 39 主驾驶门状态 Driver door status
13 刹车灯开关 Brake light switch 40 引擎盖开关 Engine hood switch
15 主驾座椅加热 Main seat heating 41 近光灯继电器 Low beam relay
16 副驾座椅加热 Passenger seat heating 42 报警喇叭继电器 Alarm horn relay
17 前雨刮低速继电器 Front wiper low-speed relay 44 后外侧转向灯反馈 Rear outside turn light feedback
18 远光灯继电器 High beam relay 46 LIN2 LIN2
21 前雨刮归位开关 Front wiper return switch 47 左日间行车灯 Left daytime running light
23 位置灯+牌照灯 Position light + license plate light 48 制动灯 Brake light
2 Main Components 主要部件
l Body controller Module 车身控制器(3608100S5504)
BCM(PEPS)
ID E 钥匙码
ID E1 钥匙码1 ID E1
Write into PEPS 钥匙码1
ID、SK
写入PEPS
ID、SK
ID E2 钥匙码2
ID E3 钥匙码3
ID E4 钥匙码4
ID E2
ID、SK
钥匙码2
2 Main Components 主要部件
l Low-frequency antenna 低频天线
BCM
+ -
low-frequency antenna
低频天线
2 Main Components 主要部件
l Spare antenna 备用天线
BCM
Note: The spare antenna is installed below the armrest box of the sub-instrument panel. When using the spare start function, the
key should be placed at the key pattern in the armrest box (under the rubber pad).
注:备用天线安装在副仪表台扶手箱的下方,使用备用启动功能时,钥匙需放置在扶手箱内的钥匙图案处(橡胶垫下)
2 Main Components 主要部件
l Button-type ignition switch 按键式点火开关
7 / /
1 B+ 电源+
2 Grounding 地
3 / /
5 IG1 IG1电
7 CAN-H CAN高
8 CAN-L CAN低
3 Working Principle 工作原理
l Unlock/lock - Using door handle 开锁/闭锁-使用门把手
3
BCM receive the signal, drive HUS 6
125KHz LF 2 BCM接到信号,驱动HUS
BCM
Judge Legality
5 判断合法性
BCM
433.42MHz RF
1 Door handle unit Judge Legality
门把手单元 2 判断合法性
3 Working Principle 工作原理
l Unlock/lock - Using door handle 开锁/闭锁-使用门把手
After closing the driver door, the user can insert the mechanical key in the lockset and turn to lock that door. This event will be detected
by BCM which, if all other doors are closed, will lock all other doors so that the vehicle will be locked. If at least one door was not closed,
BCM will unlock the driver door to tell the user to close all doors before attempting to lock the vehicle
关闭驾驶员车门后,用户可以将机械钥匙插入锁具中并转动以锁定该车门。BCM将检测到该事件,如果所有其他车门关闭,BCM
将锁定所有其他车门,从而锁定车辆。
If the vehicle is unlocked, press the switch and BCM will unlock the vehicle directly without checking whether an identifier exists in the
area covered by the bumper antenna
如果车辆已经解锁,此时按下尾门开关,BCM将直接解锁车辆,而不检查保险杠天线覆盖区域是否存在标识符
Low-frequency antenna
433.42MHz RF 低频天线 4
3
3 Working Principle 工作原理
l Start/stop - Standby start 启动/停机-备用启动
Low-frequency antenna
433.42MHz RF 低频天线 6
3
2
3
5
Spare antenna
备用天线
3 Working Principle 工作原理
l Start/stop - Emergency start 启动/停机-紧急启动
Ø In P gear position, it can start engine in emergency without pressing down brake pedal by keep press start button for 15
seconds.
Ø 紧急启动:P档,不踩制动踏板按住启动开关15s,可以紧急启动车辆
Ø When engine is running and vehicle speed is lower than 4 km/h, depressing Engine button will stop the engine
Ø 当发动机运转且车速低于4公里/小时时,按下发动机按钮将停止发动机
Ø In P gear position, engine is idling running, keep press start button for 3 seconds or press it 3 times within 3 seconds, can let the
engine off in emergency.
Ø 紧急停机:长按启动开关3s或者在3s内连续按下启动开关3次,可以紧急关闭发动机
4 Maintenance Points 维修要点
l Match learning 匹配学习
Ø Matching reason: once the controller is replaced, the information inside the controller is lost and needs to be matched again
匹配原因:控制器一旦更换,控制器内部的信息就丢失需要重新匹配
KEYID(1~4)
SC SC
KEY ID SC
VIN
SK SK V_Coad.ESCL VIN
SK
ID SK
BCMID VIN
V_Coad.ESCL
1. JDS can be used to write the SK and ID into the key from BCM JDS通过指令可以把 BCM的密钥码SK和ID写入到钥匙里
2. BCM reads the key identifier KeyID and stores it BCM读取钥匙的标志码KeyID并存储
3. If it is found that the data already exists in the key during the writing process, then compare whether the data stored in BCM and the data stored in the
key are the same, it will continue to match if the data is same, otherwise it will fail to match. 若在写入过程中发现钥匙内已经存在数据,则对比BCM
内存储的数据和钥匙内存储的数据是否相同,相同则继续匹配,不同则匹配失败。
4 Maintenance Points 维修要点
l Match learning 匹配学习
JDS can delete the KeyID of all keys in the BCM.The information in the key is not processed
JDS通过指令可以删除BCM内所有钥匙的KeyID。钥匙内信息不作处理
4 Maintenance Points 维修要点
l Match learning 匹配学习
1. JDS uses the command to reset the BCM and delete all the keyIDs. JDS通过指令把BCM复位,删掉所有KeyID
2. Manually input the PIN code and write it into BCM. 手动输入PIN码,并写入BCM
3. Teach the SK to BCM from EMS and overwrite the SK1 of BCM . 从EMS中将密钥码SK教给BCM,并覆盖BCM出厂的密钥码SK1
4. The smart key should be added if the BCM is replaced. 钥匙和BCM要一起更换,增加智能钥匙
4 Maintenance Points 维修要点
l Match learning 匹配学习
1. JDS can be used to learn SK and PIN code to EMS form BCM . JDS通过指令把BCM的密钥码SK和PIN码交给EMS
2. Write the SK and PIN code to the new EMS. 把密钥码SK和PIN码写入新EMS
4 Maintenance Points 维修要点
l Match learning 匹配学习
1. JDS can be used to learn SK and PIN code to TCU form BCM . JDS通过指令把BCM的密钥码SK和PIN码交给TCU
2. Write the SK and PIN code to the new TCU. 把密钥码SK和PIN码写入TCU
4 Maintenance Points 维修要点
l Match learning 匹配学习
After receiving the JDS instruction, BCM teaches the V_CODE value to ESCL. 在接到JDS指令后,BCM将V_CODE值交给ESCL
4 Maintenance Points 维修要点
l JDS function JDS功能
4 Maintenance Points 维修要点
l PEPS alarm prompt PEPS报警提示
Communication with BCM lost Anti-theft controller has not saved the key
U014087 B130500
与 BCM 通讯丢失 在防盗控制器中没有保存钥匙
ESCL communication lost Driver's side door handle antenna open circuit
U021287 B150013
ESCL 通信丢失 驾驶侧门把手天线开路
PSE Internal EEPROM module error Front inner low-frequency antenna open circuit
B130000 B150213
PSE 内部 EEPROM 模块异常 车内前低频天线开路
PSE Internal EEPROM module error Rear inner low-frequency antenna open circuit
B130000 B150413
PSE 内部 EEPROM 模块异常 车内后低频天线开路
5 Typical Faults 典型故障
l PEPS DTC code PEPS故障码
missing message BCM_VehSt2 DC Motor doesn't reach its destination position in time
U014687 B120674
BCM_VehSt2 报文丢失 直流电机未在指定时间内完成动作