Professional Documents
Culture Documents
Jis Piping Handbook
Jis Piping Handbook
Jis Piping Handbook
c om
Contents
Page
1. Classification 1-4
2. Piping System Abbreviation 7
3. Symbol 8- 24
4. Piping Drafting Symbol For Pipe & Pipe Fittings 25 - 26
5. Method For Identification Of Pipes And Its System 27
6. Installation Guidance 28 - 31
7. Pipe Insulation Standard 32 - 44
8. Pipe Expansion Loint Application Standard 45
9. Pipe 46 - 54
10. Flange 55 - 66
11. Sleeve/Socket/Union Joint 67 - 72
12. Elbow 73 - 77
13. Reducer 78 - 84
14. Tee Piece (Equal) 85 - 86
15. Tee Piece (Reducing) 87 -92
16. Expansion Joint 93 - 109
LRS
DNV
Table A2 Minimum nominal wall thickness for steel pipes (except pipes covered by Load Line Regulations)
Bilge, air, overflow and
sounding pipes through
Air, overflow and sounding Bilge, ballast and general ballast and fuel oil tanks,
Pipes in general
pipes for structural tanks seawater pipes ballast lines through fuel
External diameter D, mm 3), 4), 5),
1), 2), 3), 1), 3), 4), oil tanks and fuel oil lines
6), 7), 8)
5), 8), 9) 5), 7), 8) through ballast tanks
1), 2), 3), 4),
5), 7), 8), 9)
10.2 - 12 1.6
13.5 – 17.2 1.8
20 2
21.3 - 25 2 3.2
26.9 – 33.7 2 3.2
38 – 44.5 2 4.5 3.6 6.3
48.3 2.3 4.5 3.6 6.3
51 – 63.5 2.3 4.5 4 6.3
70 2.6 4.5 4 6.3
76.1 – 82.5 2.6 4.5 4.5 6.3
8.9 - 108 2.9 4.5 4.5 7.1
114.3 - 127 3.2 4.5 4.5 8
133 – 139.7 3.6 4.5 4.5 8
152.4 – 168.3 4 4.5 4.5 8.8
177.8 4.5 5 5 8.8
193.7 4.5 5.4 5.4 8.8
219.1 4.5 5.9 5.9 8.8
244.5 - 273 5 6.3 6.3 8.8
298.5 - 368 5.6 6.3 6.3 8.8
406.4 - 457 6.3 6.3 6.3 8.8
1) For pipes efficiently protected against corrosion, the thickness may be reduced by an amount up to not more than 1 mm.
2) For sounding pipes, except those for cargo tanks with cargo having a flash point less than 60° C, the minimum wall thickness is intended
to apply to the part outside the tank.
3) For threaded pipes, where allowed, the minimum wall thickness is to be measured at the bottom of the thread.
4) The minimum wall thickness for bilge lines and ballast lines through deep tanks and for cargo line is subject to special consideration.
5) For larger diameters the minimum wall thickness is subject to special consideration.
6) The wall thickness of pipes within cargo oil and ballast tanks in systems for remote control of valves is not to be less than 4mm.
7) For inlets and sanitary discharges see Pt. 3 Ch. 2 Sec. 11 K 100.
8) For stainless steel pipes the minimum wall thickness will be specially considered, but it is in general not to be less than given in Table A1
for pipes of copper alloys.
9) For air pipes on exposed decks, see Pt 3 Ch. 2 Sec. 11 K 300.
1) The wall thickness of pipes within cargo oil and ballast tanks in
systems forAl-Brass.
3 mm for remote control
2 mmoffor
valves
Cu-Niisand
not stainless
to be lesssteel.
than :
2
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 3/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
NK
Table D12.6(1) Minimum Thickness of Steel Pipes
3
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 4/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
1), 3)
Table D12.6 2) Minimum Thickness of Steel Pipes )
Notes:
1 Where the thickness of pipes specified in standards does not comply with the minimum thickness in this
Table, the standard pipe may be used if the difference is 0.4 mm or less.
2 Pipes are to be galvanized at least inside, except those fitted in the engine room.
3 For pipes with a nominal diameter other than shown in this Table, their minimum diameter will be
considered by the Society in each case.
4
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 5/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
SYMBOL...................................................................................................................................................................... 3
STANDARD VALVES.............................................................................................................................................3
SPECICAL VALVE .................................................................................................................................................4
REMOTE OPERATED VALVE...............................................................................................................................4
REMOTE & AUTOMATIC CONTROL VALVES..................................................................................................... 5
TRAPS.................................................................................................................................................................... 6
STRAINERS ...........................................................................................................................................................6
MOUTH PIECE.......................................................................................................................................................6
AIR ESCAPE HEADS.............................................................................................................................................6
FITTINGS................................................................................................................................................................7
GENERAL...............................................................................................................................................................9
REMOTE OPERATED REACH ROD PIECE......................................................................................................... 9
PUMP MARKS...................................................................................................................................................... 10
PUMPS .................................................................................................................................................................10
SWITCHES........................................................................................................................................................... 10
INSTRUMENTATION ...........................................................................................................................................10
FIRST CODE LETTER (MEASURING OBJECT).................................................................................................12
SUBSEQUENT CODE-LETTER (INSTRUMENT FUNCTION)............................................................................ 13
EXAMPLE............................................................................................................................................................. 13
6
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 7/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
NO SYSTEM ABBREVIATION
1 Ballast line WB/SW
2 Cooling sea water line CW/SW
3 Hydrant and wash deck line SW
SYMBOL
SYMBOL
NAME REMARKS
M
E For as fitted plan For key plan
T
I
Screw down
(globe & angle) Socket
check valve
Swing check
(with handle) Bat Welded
valve
S
E
V
Cock BITE union
L
A 3-way cock (T & L type)
V
D
R
A Sluice valve
D
N
A
T
S Sluice valve (water seal)
Butterfly valve
(vertical &
Storm valve
horizontal)
Valve manifold
8
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 9/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
SYMBOL
M
E NAME REMARKS
T
I
For as fitted plan For key plan
Surface valve
Needle valve
SYMBOL
M
E NAME REMARKS
T
I
For as fitted plan For key plan
Governor valve
Press-vacuum relief
(globe & angle)
valve
Miniature direct control
(with strainer)
valve
S
E Direct operated control valve (with handle) included
V
L
A
V
L Diaphragm control valve
O
R
T
N Diaphragm control valve (with handle)
O
C
C
I
T Diaphragm control valve (with positioner)
A
M
O
T Level control valve
U
A
&
E Level control valve (Hi-flo)
T
O
M
E Level control valve (ball tap)
R
10
SYMBOL
M
E NAME REMARKS
T
I
For as fitted plan For key plan
Syphon breaker
Bilge hat
Strainer (single)
S
R Strainer (duplex)
E
N
I
A
R Mud box
T
S
Rose box
Bell mouth
Air escape pipe bend (globe & angle) With filling cap
head (by reach rod)
S
D Air escape gooseneck head
A
E float check type without gauge wire net
H
E Air escape gooseneck head
P
A float check type with gauge wire net
C
S
E Air escape bonnet head
I
R without gauze wire net
A
Air escape bonnet head Screw type
with gauze wire net Flange type
11
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 12/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
SYMBOL
M
E NAME REMARKS
T
I
For as fitted plan For key plan
Off-set bend
Sounding cap
Hose flange
Normal
Blank flange
open
Normal
Spectacle flange
shut
Orifice
S Boss
G
IN
T
T
I
F Bottom plug (P1-type)
Drain hole
Anchoring piece
Seel pot
Reducer
12
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 13/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
SYMBOL
M
E NAME REMARKS
T
I
For as fitted plan For key plan
Tee piece
Penetrating piece
Phone
Special flange
Whistle
Hopper
Sleeve
Scupper piece without rose plate
type
13
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 14/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
SYMBOL
M
E NAME REMARKS
T
I
For as fitted plan For key plan
Waste pipe
Sprinkling pipe
L
A F.O. pipe with tracer
R
N
E
E Capillary tube
G
Hydraulic line
Electric wire
Overboard discharge
“U” seal
H
C
A
E
R
D E
E C
T E
A I
R P
E D
P O
O R
E
T
O
M
E
R
14
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 15/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
SYMBOL
M
E NAME REMARKS
T
I
For as fitted plan For key plan
Remote start
Remote stop
S
K
R Automatic start & stop
A
M
P
M Automatic start
U
P
Automatic stop
Automatic change
Hand pump
Priming pump
S Ejector
P
M
U
P Eductor
Thermal switch
S
E Limit switch
H
C
T
I
W Level switch
S
Pressure switch
SYMBOL
M
E NAME REMARKS
T
I
For as fitted plan For key plan
Thermometer pocket
Thermometer
Float gauge
Flow meter
Sight glass
N
O
I
T Ships draft gauge
A
T
N
E Flat glass oil level gauge
M
U
R
T Salinity cell
S
N
I
Electric type pressure indicator
With code-letter
Signal transmitter
when necessary
Relay
16
SYMBOL
M
E NAME REMARKS
T
I
For as fitted plan For key plan
A Composition
Particular composition
Co2
(carbon dioxide)
Particular composition
O2
(oxygen)
Particular composition
CL
(salinity)
Particular composition
PH
(hydroneum ion
)
T
C D Density
E
J
B
O
G F(Fr) Flow (Flow rate)
IN
R
U L Level
S
A
E
M
( M Humidity
R
E
T
T P Pressure
E
L
E
D Pd Pressure differential
O
C
T
S Q Heat calorie
R
I
F
S Speed
T Temperature
V Viscosity
W Weight
X Other variation
17
SYMBOL
M
E NAME REMARKS
T
I
For as fitted plan For key plan
)
N
O
I I Indication 1) Lettering order
T as follows :
C
N
U R Recorder
F I or R-C-S-A
T
N
E C Controller 2) In case of
M recorder
U
R monitor &
T S Counter
S logger letter
N
I( “ I “ not written
R A(WITH H OR L) Alarm (high or low)
E
T
T
E
L
- C/R Control console
E
O
D
C B/G Boiler gauge board
T
N
E
U E/R Main engine gauge board
Q
E
S
B W/H Wheel house
U
S
Pd
D1
Control panel pressure indicator
(pneumatic transmitted)
TC Temperature controller
E
L
P
M TA High temperature alarm
A H
X
E
LRCH
Level recording controller with high & low
ML alarm
P TO ACC
Pressure transitter (pneumatic) for A.C.C.
VALVE NOTES:
1) size of
SYMBOLS
to be
TYPE REMARK shown on
PLAN VIEW ELEVATION SECTION VIEW respective
plan and side
Direction of flow to view are taken
Globe valve be shown if from handle of
necessary valve size of
whichever
Angle valve greater
2) when there
Globe non-return is
valve arrangement
difficulty of
Angle non-return sluice valve on
valve plan and side
view, a sketch
Opening indicator of the valve
Sluice valve are to be shown in should be
principal included in
On plan and on
Gear control
section view show
sluice valve
such indicator
Globe non-return
hose valve
Anglevalve
hose non-return
Remote control
globe valve
Remote control
angle valve
Remote control
globe non-return
valve
Remote control
angle non-return
valve
19
VALVE Notes:
SYMBOLS
TYPE REMARK
PLAN VIEW ELEVATION SECTION VIEW
Emergency
closing valve
Screw globe
valve
Screw angle
valve
Lifting non-return
globe valve
Lifting non-return
angle valve
Lifting non-return
Foot valve
standing valve
Swing non-return
valve
Magnet valve
2-way cock
20
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 21/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
SYMBOLS
TYPE REMARK
PLAN VIEW ELEVATION SECTION VIEW
(L TYPE)
3-way cock
(T TYPE)
Butterfly valve
Storm valve
135
M
Electric motor M
operated globe
valve M
Electric motor M M
operated sluice
valve M
To be drawn reach
Reach rod rod and valve
number
Globe
Breather valve
Angle
21
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 22/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
SYMBOLS REMARK
TYPE
PLAN VIEW ELEVATION SECTION VIEW
Eductor
Single strainer
Duplex strainer
Y-type strainer
Mud box
Rose box
Steam trap
pass)
BY - PASS In case of with by-
Steam trap (with pass type must be
strainer) drawn “sentence”
Hand pump
Water cock
Swing type
22
SYMBOLS
TYPE REMARK
PLAN VIEW ELEVATION SECTION VIEW
Scupper
Box-type
scupper
Hopper
Hopper with
sight glass
Bell mouth
Sight glass
Flow direction to
be shown in
Expansion joint
accordance with
maker drawing
To be marked
Spectacle flange “SHUT” or
O(S) O(S) O(S) “OPEN”
Orifice
Flow meter
Fix-type
thermometer
Size of seat to
Thermometer beexample
For drawn
Seat
M - 20
23
SYMBOLS
TYPE REMARK
PLAN VIEW ELEVATION SECTION VIEW
Joining piece
Slot in welding
type
Penetration
piece
Penetrating Inbutt
case of
joint Deckflat
or In case of
penetration
sleeve
Jacket type
sleeve
Special flange
24
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 25/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
Single line Double line Single line Double line Single line
Top view
Elevation
90° Elbow
view
Bottom view
Top view
Elevation
45° Elbow
view
Bottom view
Top view
Elevation
T Joint
view
Bottom view
Top view
Elevation
Y Joint
view
Bottom view
25
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 26/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
Top view
Reducer
Elevation view
Single line
Flange joint
Double line
Double line
26
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 27/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
100CW-107-01
100SW-103-01
100SW-101-01 150SW-102-01
PIPE PIECE
MARK
SYSTEM REF.
TO K-PLAN
PIPING SYSTEM
100CW-01-107
100SW-01-103
100SW-01-101 150SW-01-102
SYSTEM NOS.
PIPING SYSTEM
27
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 28/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
INSTALLATION GUIDANCE
28
Note :
0
0
1
5
4 x 10Ø Holes
2
TANK TOP
0
0
3
0
0 TANK TOP
3
0
0
3
0
0
1
0
0
1 N=4
4
3 1
Bottom
29
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 30/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
0
0
0
1
4
1
3
TANK BOTTOM
30
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 31/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
)
0 R
5 L(
1
Deck H (m/m)
0.25L FWD
Upper Deck 760
Deck
5
1
Detail Detail
NOTE:
• Inclination of air escape pipe to be not less than 30 degrees from the horizontal plane.
31
INSULATION
COVER
MATERIAL
PIPE LINE APPLIED PLACES Flange, Flange, REMARKS
Pipe valve & Pipe valve &
etc etc
F.R.P.
Only the the
having parts of pipes of
possibility (Fibreglass
Weather parts Rock wool - reinforced - FIG - 1
contacting with human
Deck steam plastic)
body
line, exhaust (polytight)
line and tank Pipe above 10 FIG - 2
Accommodation Rock wool Rock wool Glass cloth Glass cloth
heat line mm FIG - 5
pump room , All
steering gear room pipes
Pipe dia 10 mm
& pipe passgae Not to be insulated
and below
F.R.P.
Domestic Weather parts All pipes Rock wool - (Polytight) - FIG -1
steam and
drain Glass cloth Glass cloth FIG - 5
Accommodation All pipes Rock wool Rock wool
(Note 1) (Note 1) FIG - 2
Note 1 :- Polytight to be applied to the pipes above one (1) meter from floor which are led in wet space
Note 2 :- PVC tubes not to be insulated
Note 3 :- Duct in the ceiling and/or lining not to be insulated.
32
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 33/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
Rock wool
154°C – 101°C 20 20 20 20 25 25 25 25 25 25 25 30 30
moulding
100°C – 60° C 20 20 20 20 20 20 20 25 25 25 25 25 25
33
Application :
Insulation Method
5 4 3 2
1
34
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 35/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
1. Application :
2. Insulation Method
3 3
2
1
35
1. Application :
2. Insulation Method
5
or
5 4 3 2
1
36
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 37/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
1. Application :
2. Insulation Method
1 2
37
1. Application :
Pipe fittings such as flange, valve, T-piece, socket, sleeve and support.
2. Insulation Method
A) FLANGE B) VALVE 5
5
4
4 2 3 3
1 1
c) T-PIECE D) SUPPORT
PENETRATING PIECE IS SIMILAR
2 3
4 5 TO PIPE SUPPORT.
MIN. 25 MM
TO ALLOW PIPES TO SLIDE
38
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 39/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
1. Application :
2. Insulation Method
2 3
1
3
2 4 5
6 & 6
1
4 AL-Foil
6 Coating for use in Ref. Prov, chamber (1.0 kg/m²) Elastonato T/# 9840
6’ Coating for use except above space 2 coat (1.3 kg/m²/2-coats) Seal FAS
4. Note : In case of freon pipe for vegetable,, fish and meat room, being led in lobby, these pipes to be insulated
with 25 mm thick foamed polyurethane and finished coat.
39
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 40/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
1. Application :
2. Insulation Method
4
5& 6
1
4
5& 6 3
3
1
3 Hard foam polyurethane Specific gravity : 0.1 g/cm³ JIS A9512 No 1 & above
4 AL-Foil
40
1. Application :
2. Insulation Method
1 2
41
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 42/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
1. Application :
2. Insulation Method
5 6 7 8
2
2 Adhesive
3 #11 Canvas
42
1. Application :
2. Insulation Method
SPIRAL DUCT
& FLEXIBLE DUCT 1 2 3 4 5
6 3 2 7 8 9
3 Adhesive Width : 50 mm
4 #11 Canvas
43
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 44/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
IS INSULATING METHOD OF PENETRATING PIECE FOR FIRE SAFETY MEASURE – (FIG – 11)
1. Application :
To be applied to penetrating piece to the A-15, A-30 and A-60 class bulkhead and deck.
2. Insulation Method
T
PIPE OR DUCT
L
3. Material
Mark Material Remarks Note
0.8t Galv. Steel band ( Dia > 125 ) Pipe dia 125
1
#18 Galv. Iron wire ( Dia < 100 ) Pipe dia 100
4. Note :
Length “L”
L > 1.5 D (Dia above 100 mm)
L > 150 mm ( Dia 100 mm and under)
‘T” : Thickness of insulation
44
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 45/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
2.1 Dressor
- typepipe
For expansion
nominaljoint
size below 300A
1 piece is required for pipe length within 24M
- For deck machinery operation hydraulic line, 1 piece is required for pipe length within 40M
3. Expansion absorbing rate for expansion joint fitting.
TYPE ABSORBING RATE REMARKS
Bellow type 70 mm
- Due to the change of the temperature, the expansion rate base 1°C, will be 0.012mm pper 1m for
steel pipe and about 0.017mm per 1m for copper pipe.
45
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 46/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
PIPE
(1) Electric resistance welded steel pipe of group II and seamless carbon steel pipes of group I
6 1/8 10.5 2.0 0.419 1.7 0.369 2.4 0.479 1.7 0.369 2.4 0.479
8 ¼ 13.8 2.3 0.652 2.2 0.629 3.0 0.799 2.2 0.629 3.0 0.799
10 3/8 17.3 2.3 0.851 2.3 0.851 3.2 1.11 2.3 0.851 3.2 1.11
15 1/2 21.7 2.8 1.31 2.8 1.31 3.7 1.64 2.8 1.31 3.7 1.64 4.7 1.97
20 3/4 27.2 2.8 1.68 2.9 1.74 3.9 2.24 2.9 1.74 3.9 2.24 5.5 2.94
25 1 34.0 3.2 2.43 3.4 2.57 4.5 3.27 3.4 2.57 4.5 3.27 6.4 4.36
32 1 1/4 42.7 3.5 3.38 3.6 3.47 4.9 4.57 3.6 3.47 4.9 4.57 6.4 5.73
40 1 1/2 48.6 3.5 3.89 3.7 4.10 5.1 5.47 3.7 4.10 5.1 5.47 7.1 7.27
50 2 60.5 3.8 5.31 3.9 5.44 5.5 7.46 3.9 5.44 5.5 7.46 8.7 11.1
65 2 1/2 76.3 4.2 7.47 5.2 9.12 7.0 12.0 5.2 9.12 7.0 12.0 9.5 15.8
80 3 89.1 4.2 8.79 5.5 11.3 7.6 15.3 5.5 11.3 7.6 15.3 11.1 21.4
90 3 1/2 101.6 4.2 10.1 5.7 13.5 8.1 18.7 5.7 13.5 8.1 18.7 12.7 27.8
100 4 114.3 4.5 12.2 6.0 16.0 8.6 22.4 6.0 16.0 8.6 22.4 11.1 28.2 13.5 33.6
125 5 139.8 4.5 15.0 6.6 21.7 9.5 30.5 6.6 21.7 9.5 30.5 12.7 39.8 15.9 48.6
150 6 165.2 5.0 19.8 7.1 27.7 11.0 41.8 7.1 27.7 11.0 41.8 14.3 53.2 18.2 66.0
200 8 216.3 5.8 30.1 8.2 42.1 12.7 63.8 8.2 42.1 12.7 63.8 18.2 88.9 23.0 110
250 10 267.4 6.6 42.4 9.3 59.2 15.1 93.9 9.3 59.2 15.1 93.9 21.4 130 28.6 168
300 12 318.5 6.9 53.0 10.3 78.3 17.4 129.0 10.3 78.3 17.4 129 25.4 184 33.3 234
350 14 355.6 7.9 67.7 11.1 94.3 19.0 158 11.1 94.3 19 158 27.8 225 35.7 282
400 16 406.4 7.9 77.6 12.7 123 21.4 203 12.7 123 21.4 203 30.9 286 40.5 365
450 18 457.2 7.9 87.5 14.3 156 23.8 254 14.3 156 23.8 254 34.9 363 45.2 459
500 20 508.0 7.9 97.4 15.1 184 26.2 311 15.1 184 26.2 311 38.1 441 50.0 565
46
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 47/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
48
49
COPPER PIPES
1. Scope
This standard covers copper pipe used for general piping.
2. Dimensions
32 35 - - 2.3 2.10 - -
NOTE: 1) Pipe outside diameter 270 mm and smaller shall conform to JIS H3603
50
25 1 28.25 1.4 SWG 17 0.99 2.0 SWG 14 1.38 2.6 SWG 12 1.76
40 1½ 40.95 1.4 SWG 17 1.46 2.0 SWG 14 2.05 3.7 SWG 9 3.63
50 2 54.05 1.6 SWG 16 2.22 2.0 SWG 14 2.75 4.5 SWG 7 5.89
51
OUTSIDE PIPE
DIAMETER OF WALL THICKNESS S (mm) THEOR.
WEIGHT
NOMINAL ACTUAL (1) (kg/m)
(1) 2 3 4 5 6
(INCH) (mm)
SEAMLESS
¼ 14 • 1 2.5 0.36
½ 20 • 1 1.5 2 4 0.53
¾ 25 • 1.5 2 4 0.99
1 30 • 1.5 2 2.5 5 1.20
1¼ 38 • 1.5 2 3 6 1.55
2½ 76 • 2 2.5 - - 4 4.15
3 89 • 2 2.5 3 - 4 4.86
10 267 • 3 4 - 6 8 10 22.24
SEAM WELDED
10 267 • 3 4 - 6 8 10 22.24
32 813 • 6 7 11 135.00
36 914 • 8 12 203.57
Pipe in sizes and alloys other than the above and larger than 1016 mm are also available
• Selected sizes are in accordance with the pipe components as per DIN 86087 up to 86090
52
2. Dimension
THICKNESS & WEIGHT
NOMINAL DIAMETER OUTSIDE
DIAMETER 90/10 Cu-Ni
(mm)
Mm INCH THICKNESS (mm) * WEIGHT (kg/m)
53
FLANGE
JIS STANDARD 5 kg/cm² SLIP – ON WEDLING STEEL PIPE FLANGE (JIS B 2221)
FLANGE – JIS 5K
W1
W1 h a r
t b t
T
W2 W2
d 0
d 0
C C
D D
DIMENSION
NOM. OUT.
do D t T a b r C NO. h THREAD L W1 W2 (kg)
DIA. DIA.
10 17.3 17.8 75 9 - - - - 55 4 12 M10 35 5 2.5 0.27
1000 1016 1021 1195 32 60 1058 1066 5 1130 28 33 M30 100 14 9 88.5
JIS STANDARD 10 kg/cm² SLIP – ON WEDLING STEEL PIPE FLANGE (JIS B 2222)
W1
W1
h a r
h
t b t T
W2 W2
d0 d0
C C
D D
NOM.DIA 10 - 225 NOM.DIA 250 - 1000
DIMENSION
NOM. OUT.
do D t T a b r C NO. h THREAD L W1 W2 (kg)
DIA. DIA.
10 17.3 17.8 90 12 - - - - 65 4 15 M12 40 5 2.5 0.52
15 21.7 22.2 95 12 - - - - 70 4 15 M12 40 5 3 0.57
500 508 511 675 30 48 548 554 6 620 20 27 M24 100 14 8 37.6
550 558.8 562 745 32 52 604 610 6 680 20 33 M30 100 15 9 49.7
600 609.6 613 795 32 52 656 662 6 730 24 33 M30 110 16 10 52.6
650 660.4 664 845 34 56 706 712 6 780 24 33 M30 110 16 10 60.6
700 711.2 715 905 34 58 762 770 6 840 24 33 M30 110 17 10 70.6
750 762 766 970 36 62 816 824 6 900 24 33 M30 110 18 11 85.8
800 812.8 817 1020 36 64 868 876 6 950 28 33 M30 110 19 12 91.2
(850) 863.6 868 1070 36 66 920 928 6 1000 28 33 M30 110 19 12 98.6
900 914.4 919 1120 38 70 971 979 6 1050 28 33 M30 110 22 14 109
1000 1016 1021 1235 40 74 1073 1081 6 1160 28 39 M36 120 22 14 133
JIS STANDARD 16 kg/cm² SLIP – ON WEDLING STEEL PIPE FLANGE (JIS B 2223)
a
W1
r
b T
t
W2
d 0
C
D
90 101.6 102.6 210 18 30 120 124 6 170 8 23 M20 65 6.5 4.5 3.95
150 165.2 166.6 305 22 38 196 202 6 260 12 25 M22 75 8 5.5 9.62
200 216.3 218 350 22 40 244 252 6 305 12 25 M22 80 9 6.5 12.1
250 267.4 269.5 430 24 44 304 312 6 380 12 27 M24 85 9 6.5 20.0
300 318.5 321 480 26 48 354 364 8 430 16 27 M24 90 11 6.5 24.4
350 355.6 358.1 540 26 52 398 408 8 480 16 33 M30 x3 105 12 8 35.0
400 406.4 409 605 28 60 446 456 10 540 16 33 M30x3 110 12 8 46.2
450 457.2 460 675 30 64 504 514 10 605 20 33 M30 x3 115 16 9 61.9
73.2
500 508 511 730 30 68 558 568 10 660 20 33 M30x3 120 16 10
5
550 558.8 562 795 32 70 612 622 10 720 20 39 M36 x3 130 18 11 88.1
600 609.6 613 845 32 74 666 676 10 770 24 39 M36x3 135 18 11 98.8
57
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 58/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
JIS STANDARD 16 kg/cm² SLIP – ON WEDLING STEEL PIPE FLANGE (JIS B 2223)
45°
d0
DIMENSION
NOM. OUT.
do D t T a b r f g C No. h Thread L W1 W2 (kg)
DIA. DIA.
650 660.4 664 895 48 77 704 726 10 5 770 820 24 39 M 36x3 140 18 12 101
700 711.2 715 960 50 80 754 776 10 5 820 875 24 42 M 39x3 150 18 12 120
750 762.0 766 1020 52 83 806 832 10 5 880 935 24 42 M 39x3 150 18 12 141
800 812.8 817 1085 54 86 865 885 10 5 930 990 24 48 M 45x3 160 22 16 161
850 863.6 868 1135 56 89 916 936 10 5 980 1040 24 48 M 45x3 170 22 16 177
900 914.4 919 1185 58 93 968 986 10 5 1030 1090 28 48 M 45x3 170 22 16 191
1000 1016.0 1021 1320 62 99 1070 1098 12 5 1140 1210 28 56 M 52x3 180 22 16 230
1100 1117.6 1123 1420 66 105 1180 1200 12 5 1240 1310 32 56 M 52x3 190 26 19 289
1200 1219.2 1225 1530 70 112 1282 1302 12 5 1350 1420 32 56 M 52x3 200 26 19 348
58
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 59/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
d1
d3
d2
b h
125 5 254 163.5 143.6 22.2 185.7 215.9 36.5 8 22.2 M 20 x 70 6.8
150 6 279.4 192.1 170.7 23.8 215.9 241.3 39.7 8 22.2 M 20 x 75 8.6
200 8 342.9 246.1 221.5 27.0 269.9 298.4 44.4 8 22.2 M 20 x 80 13.6
250 10 406.4 304.8 276.3 28.6 323.8 361.9 49.2 12 25.4 M 22 x 85 19.5
300 12 482.6 365.1 327.1 30.1 381.0 431.8 55.6 12 25.4 M 22 x 90 29.1
350 14 533.4 400 359.1 33.3 412.7 476.2 57.1 12 28.6 M 24 x 95 38.6
400 16 596.9 457.2 410.5 34.9 469.9 539.7 63.5 16 28.6 M 24 x 100 42.2
450 18 635 504.8 461.8 38.1 533.4 577.8 68.3 16 31.7 M 27 x 110 54.5
500 20 698.5 558.8 513.1 41.3 584.2 635.0 73.0 20 31.7 M 27 x 120 70
600 24 812.8 663.6 615.9 46.0 692.1 749.3 82.5 20 34.9 M 30 x 130 95
700 28 927.1 781.0 717.5 50.8 793.7 863.6 87.3 28 34.9 M 30 x 140 123
750 30 984.2 831.8 768.3 52.4 857.2 914.4 88.9 28 34.9 M 30 x 145 138
900 36 1168.4 966.8 920.7 58.7 1022.3 1085.8 161.9 32 41.3 M 36 x 160 211
59
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 60/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
d1
d3
d2
b h
g
k
D
125 5 279.4 177.8 143.8 33.3 185.7 234.9 50.8 8 22.2 M 20 x 95 12.7
150 6 317.5 206.4 170.7 34.9 215.9 269.9 52.4 12 22.2 M 20 x 100 17.7
200 8 381 260.3 211.5 39.7 269.9 330.2 61.9 12 25.4 M 22 x 110 26.3
250 10 444.5 320.7 276.3 46.0 323.8 378.3 66.7 16 28.6 M 24 x 125 36.8
350 14 584.2 425.4 359.1 52.4 412.7 514.3 76.2 20 31.7 M 27 x 140 74
400 16 647.7 482.6 410.5 55.5 469.9 571.5 82.5 20 34.9 M 30 x 150 100
450 18 711.2 533.4 461.5 58.7 533.4 628.6 88.9 24 34.9 M 30 x 155 127
500 20 774.7 587.4 513.1 61.9 584.2 685.8 95.2 24 34.9 M 30 x 160 148
600 24 914.4 701.7 615.9 68.2 692.1 812.8 106.4 24 41.3 M 36 x 210 222
60
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 61/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
d1
d3
d2
b h
g
k
D
R.F = ¼” = 6.4 mm
STANDARD : ANSI B 16.5
MATERIAL : ASTM-A 105 N
80 3 209.5 117.5 90.7 31.7 127 168.3 52.4 8 22.2 M 20 x 100 7.3
100 4 273 152.4 116.1 38.1 157.2 215.9 60.4 8 25.4 M 22 x 115 16.8
150 6 355.6 222.2 170.7 47.6 215.9 292.1 73.1 12 28.6 M 24 x 135 36
200 8 419.1 273 221.5 55.6 269.9 349.2 82.6 12 31.7 M 27 x 155 52
250 10 508 342.9 276.3 63.5 323.8 431.8 92.1 16 34.9 M 30 x 175 80
300 12 558.8 400 327.1 66.7 381 488.9 98.5 20 34.9 M 36 x 180 98
400 16 685.8 495.3 410.5 76.2 469.9 603.2 112.8 20 41.3 M 36 x 205 166
450 18 743.0 546.1 461.8 82.6 533.4 654.1 117.3 20 44.5 M 39 x 220 173
500 20 812.8 609.6 513.1 88.9 584.2 723.9 127 24 44.5 M 39 x 235 220
600 24 939.8 717.6 616 101.6 692.2 838.2 139.7 24 50.8 M 45 x 265 312
61
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 62/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
d1
b
d2 h
d3
g
Øk
D
125 5 254 141.3 128.1 22.2 185.7 215.9 88.9 8 22.2 M 20 x 70 8.6
150 6 279.4 168.3 154.1 23.8 215.9 241.3 88.9 8 22.2 M 20 x 75 10.9
200 8 342.9 219.1 202.7 27.0 269.9 298.4 101.6 8 22.2 M 20 x 80 17.7
250 10 406.4 273 254.4 28.6 323.8 361.9 101.6 12 25.4 M 22 x 85 23.6
300 12 482.6 323.9 304.9 30.1 381 431.8 114.3 12 25.4 M 22 x 90 36.3
350 14 533.4 355.6 336.6 33.3 412.7 476.2 127 12 28.6 M 24 x 95 46.3
400 16 569.9 406.4 387.4 34.9 469.9 539.7 127 16 28.6 M 24 x 100 57.7
450 18 635 457.2 438.2 38.1 533.4 577.8 139.7 16 31.7 M 27 x 110 63.6
500 20 698.5 508 489 41.3 584.2 635 144.5 20 31.7 M 27 x 120 77.2
600 24 812.8 609.6 590.6 46.0 692.1 749.3 152.4 20 34.9 M 30 x 130 118
750 30 984.2 762 743 52.4 857.2 914.4 130.2 28 34.9 M 30 x 145 153
900 36 1168.4 914.4 895.4 58.7 1022.3 1085.8 161.9 32 41.3 M 36 x 160 242
62
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 63/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
d1
b
d2 h
d3
g
Øk
D
125 5 254 141.3 122.3 22.2 185.7 215.9 88.9 8 22.2 M 20 x 70 8.6
150 6 279.4 168.3 146.3 23.8 215.9 241.3 88.9 8 22.2 M 20 x 75 10.9
200 8 342.9 219.1 193.7 27.0 269.9 298.4 101.6 8 22.2 M 20 x 80 17.7
250 10 406.4 273 247.6 28.6 323.8 361.9 101.6 12 25.4 M 22 x 85 23.6
300 12 482.6 323.9 298.5 30.1 381 431.8 114.3 12 25.4 M 22 x 90 36.3
350 14 533.4 355.6 330.2 33.3 412.7 476.2 127 12 28.6 M 24 x 95 46.3
400 16 569.9 406.4 381 34.9 469.9 539.7 127 16 28.6 M 24 x 100 57.7
450 18 635 457.2 431.8 38.1 533.4 577.8 139.7 16 31.7 M 27 x 110 63.6
500 20 698.5 508 482.6 41.3 584.2 635 144.5 20 31.7 M 27 x 120 77.2
600 24 812.8 609.6 584.2 46.0 692.1 749.3 152.4 20 34.9 M 30 x 130 118
63
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 64/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
d1
d2 b
h
d3
g
Øk
D
150 6 279.4 168.3 124.5 25.4 215.9 241.3 88.9 8 22.4 M 20 x 80 10.6
200 8 342.9 219.1 206.4 27.0 269.9 298.4 101.6 8 22.2 M 20 x 80 17.7
250 10 406.4 273 260.3 28.6 323.8 361.9 101.6 12 25.4 M 22 x 85 23.6
300 12 482.6 323.9 311.2 30.1 381 431.8 114.3 12 25.4 M 22 x 90 36.3
200 8 342.9 219.1 205.1 27.0 269.9 298.4 101.6 8 22.2 M 20 x 80 17.7
250 10 406.4 273 257.4 28.6 323.8 361.9 101.6 12 25.4 M 22 x 85 23.6
300 12 482.6 323.9 311.2 30.1 381 431.8 114.3 12 25.4 M 22 x 90 36.3
300 12 482.6 323.9 303.3 31.8 381 431.8 114.3 12 25.4 M 22 x 95 36.5
350 14 533.4 355.6 333.4 35.1 412.8 476.3 127.0 12 28.4 M 24 x 100 48.4
300 12 482.6 323.9 288.9 31.8 381.0 431.8 114.3 12 25.4 M 22 x 95 36.5
400 16 596.9 406.4 363.6 36.8 469.9 539.8 127 16 28.4 M 24 x 105 60.6
500 20 698.5 508 455.6 42.9 584.2 635.0 144.5 20 31.8 M 27 x 120 84.5
600 24 812.8 609.6 547.6 47.8 692.2 749.3 152.4 20 35.1 M 30 x 135 115.0
64
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 65/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
d1
d2 b
h
d3
g
Øk
D
STANDARD : ANSI B 16.5
MATERIAL : ASTM-A 105 N
WELDING-NECK 150 LBS Sched 160
NOM. DIA. SCREWS WEIGHT
Mm INCH D d1 d3 b g k H NO. d2 MxL (kg)
150 6 279.4 168.3 131.7 25.4 215.9 241.3 88.9 8 22.4 M 20 x 80 10.6
200 8 342.9 219.1 173.1 28.4 269.7 298.5 101.6 8 22.4 M 20 x 85 17.7
250 10 406.4 273 215.8 30.2 323.9 362 101.6 12 25.4 M 22 x 90 24.0
125 5 279.4 141.3 128.1 33.3 185.7 234.9 98.4 8 22.2 M 20 x 95 15.1
150 6 317.5 168.3 154.1 34.9 215.9 269.9 98.4 12 22.2 M 20 x 100 19.1
200 8 381 219.1 202.7 39.7 269.9 330.2 111.1 12 25.4 M 22 x 110 29.9
250 10 444.5 273 254.4 46.0 323.8 387.3 117.5 16 28.6 M 24 x 125 42.7
300 12 520.7 323.9 304.9 49.2 381 450.8 130.2 16 31.7 M 27 x 135 61.8
350 14 584.2 355.6 336.6 52.4 412.7 514.3 142.9 20 31.7 M 27 x 140 85.8
400 16 647.7 406.4 387.4 55.5 469.9 571.5 146 20 34.9 M 30 x 150 106
450 18 711.2 457.2 438.2 58.7 533.4 628.6 158.7 24 34.9 M 30 x 155 131
500 20 774.7 508 489 61.9 584.2 685.8 161.9 24 34.9 M 30 x 160 158
600 24 914.4 609.6 590.6 68.2 692.1 812.8 168.3 24 41.3 M 36 x 210 230
d1
d2 b
h
d3
g
Øk
D
STANDARD : ANSI B 16.5
MATERIAL : ASTM-A 105 N
WELDING-NECK 150 LBS Sched 160
NOM. DIA. SCREWS WEIGHT
Mm INCH D d1 d3 b g k h NO. d2 MxL (kg)
200 8 381 219.1 205 39.7 269.9 330.2 111.1 12 25.4 M 22 x 110 30.5
250 10 444.5 273 257 46.0 323.9 387.3 117.5 16 28.4 M 24 x 125 42.7
300 12 520.7 323.9 307.1 49.2 381 450.8 130.2 16 31.7 M 27 x 135 62.5
350 14 584.2 355.6 333.4 53.8 412.7 514.3 142.7 20 31.7 M 27 x 145 85.8
500 20 774.7 508 477.8 63.5 584.2 685.8 162.0 24 35.0 M 30 x 165 158
600 24 914.4 609.6 574.6 69.8 692.1 812.8 168.1 24 41.1 M 36 x 185 230
300 12 520.7 323.9 288.9 50.8 381 450.8 130.0 16 31.7 M 27 x 135 61.8
400 16 647.7 406.4 363.6 57.1 469.9 571.5 146 20 35 M 30 x 150 106
100 4 254 114.3 87.3 30.1 157.2 200 85.7 8 22.2 M 20 x 90 11.3
150 6 317.5 168.3 131.7 36.5 215.9 269.9 98.4 12 22.3 M 20 x 100 19.1
200 8 381 219.1 173.1 41.1 269.9 330.2 111.1 12 25.4 M 22 x 110 29.9
66
SLEEVE/SOCKET/UNION JOINT
SLEEVE TYPE JOINTS FOR STEEL PIPE
1. SCOPE: THIS STANDARD COVER SLEEVE TYPE JOINTS USED FOR GROUP II AND III PIPES
2. CONSTRUCTION, SHAPE AND DIMENSION TYPE S1 FOR JOINTS
WEIGHT
DIMENSION REFERENCE
API PIPE (KG)
NOM. DIA.
OUT.DIA
D d T L S1 2C W
67
DIMENSION REFERENCE
API WEIGHT (KG)
NOM.
PIPE D T L CUT DIA W2 (kg)
DIA. D
O.D
S2 S3 S2 S3 S2 S3 S2 S3 S2 S3 2C W
300 323.8 352.8 358.8 326.8 13.0 16.0 130 130 13.94 17.31 355 361 3.0 12
350 355.6 384.6 390.6 358.6 13.0 16.0 130 130 15.49 19.21 387 393 3.0 12
400 406.4 435.4 441.1 409.4 13.0 16.0 150 150 20.31 25.20 438 444 3.0 12
450 457.2 486.2 492.2 460.2 13.0 16.0 150 150 22.75 28.20 489 495 3.0 12
500 508.0 537.0 543.0 511.0 13.0 16.0 150 150 25.20 31.20 540 546 3.0 12
550 558.8 588.3 594.3 562.3 13.0 16.0 150 150 27.66 34.30 590 596 3.5 12
600 609.6 639.1 645.1 613.1 13.0 16.0 150 150 30.11 37.30 642 648 3.5 12
650 660.4 689.9 695.9 663.9 13.0 16.0 200 200 43.40 53.70 692 698 3.5 12
700 711.2 740.7 746.7 714.7 13.0 16.0 200 200 46.66 57.80 744 750 3.5 12
750 762.0 791.5 797.5 765.5 13.0 16.0 200 200 49.91 61.80 794 800 3.5 12
800 812.8 842.3 848.3 816.3 13.0 16.0 200 200 53.17 65.80 845 851 3.5 12
850 863.6 893.1 899.1 867.1 13.0 16.0 200 200 56.43 69.80 896 902 3.5 12
900 914.4 943.9 949.9 917.9 13.0 16.0 200 200 59.69 73.70 947 953 3.5 12
68
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 69/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
DIMENSIONS
NOM. PIPE WT
DIA. O.D B C T (kg)
A D L l S
(MIN) (MIN) (MIN)
6 10.5 11.0 17.8 9.6 7.1 25.6 6.4 3.4 3.4 0.03
10 17.3 17.8 26.8 9.6 12.7 25.6 6.4 4.5 4.5 0.07
15 21.7 22.2 32.6 9.6 16.1 28.7 9.5 5.2 5.2 0.12
20 27.2 27.7 38.7 12.7 21.4 34.5 9.5 5.5 5.5 0.18
25 34.0 34.5 46.9 12.7 27.2 38.1 12.7 6.2 6.2 0.28
32 42.7 43.2 57.0 12.7 35.5 38.1 12.7 6.9 6.9 0.37
40 48.6 49.1 62.9 12.7 41.2 38.1 12.7 6.9 6.9 0.42
50 60.5 61.1 75.9 15.9 52.7 50.9 19.1 7.4 7.4 0.75
65 76.3 77.1 93.1 15.9 65.9 50.9 19.1 8.0 8.0 1.24
69
DIMENSIONS
NOM. PIPE WT
DIA. O.D B C T (kg)
A D L l S
(MIN) (MIN) (MIN)
15 21.7 22.2 35.4 9.6 12.3 28.7 9.5 6.6 6.6 0.16
20 27.2 27.7 43.1 12.7 16.2 34.9 9.5 7.7 7.7 0.26
25 34.0 34.5 52.5 12.7 21.2 38.1 12.7 9.0 9.0 0.43
32 42.7 43.2 61.2 12.7 29.9 38.1 12.7 9.0 9.0 0.52
40 48.6 49.1 69.1 12.7 34.4 38.1 12.7 10.0 10.0 0.65
50 60.5 61.1 85.5 15.9 43.1 50.9 19.1 12.2 12.2 1.31
65 76.3 77.1 103.7 15.9 57.3 50.9 19.1 13.3 13.3 2.47
70
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 71/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
71
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 72/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
1 1
4 5 D 5 2
d d S d
d S D
b H a
L1 L
3 2 4 1
10 17.3 10 M 30 x 2 6 22 26 7 4 12 24 36 18 3 22 27 20 3 0.24
25 34.0 25 M 48 x 2 10 40 39 16 4 15 41 55 24 5 40 45 26 4 0.75
40 48.6 40 M 65 x 2 14 57 53 23 5 20 60 75 31 6 56 62 34 5 2.22
NO COMPONENT MATERIAL
1 BODY
2 UNION NUT JIS G 3101 – SS41
3 NIPPLE
4 GASKET JIS F 7102
72
ELBOW
WELDABLE 90° SHORT STEEL ELBOW
(ASTM STANDARD)
73
74
XS - 12.7 120
- 20 7.9 99.9
STD - 9.5 119
450 18 457.2 685.8
XS - 12.7 157
- 60 19.05 117
STD 20 9.5 147
500 20 508 762
XS - 12.7 190
STD 20 9.5 212
600 24 609.6 914.4
XS - 12.7 275
750 30 762 1143 STD - 9.5 333
900 36 914.4 1371.6 STD - 9.5 472.2
75
A
45° ELBOW
CAP
K
D
A
A
B E
D
D D
P
DIMENSION
NOMINAL OUTSIDE Ø 45 Ø 90 Ø 180 Ø 180
DIAMETER DIA. (MM) ELBOW ELBOW ELBOW ELBOW
D (B) (A) (P) (K) CAP
MM INCH LONG LONG SHORT LONG SHORT LONG SHORT
100 4 114.3 63.1 152.4 101.6 304.8 203.2 209.6 158.8 63.5
125 5 139.8 78.9 190.5 127 381 254 260.4 196.9 76.2
150 6 165.2 94.7 228.6 152.4 457.2 304.8 311.2 235 88.9
200 8 216.3 126.3 304.8 203.2 609.6 406.4 413 311.4 101.6
250 10 267.4 157.8 381 254 762 508 514.7 387.7 127
300 12 318.5 189.4 457.2 304.8 914.4 609.6 616.5 464.1 152.4
350 14 355.6 220.9 533.4 355.6 1066.8 711.2 711.2 533.4 165.1
400 16 406.4 252.5 609.6 406.4 1219.2 812.8 812.8 609.6 177.8
450 18 457.2 284.1 685.8 457.2 1371.6 914.4 914.4 685.8 203.2
500 20 508 315.6 762 508 1524 1016 1016 762 228.6
76
ANGLE
DIMENSION “H” ON LONG RADIUS ELBOW
N.D 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 900
°D R
76 95 114 152 191 229 305 381 457 533 610 686 762 914 1143 1372
30° 20 25 31 41 51 61 82 102 123 143 163 184 204 245 306 368
1 21 26 32 42 53 64 85 106 127 148 169 190 211 253 317 380
2 22 27 33 44 55 66 87 109 131 153 175 197 218 262 328 393
3 23 28 34 45 57 68 90 113 135 158 181 203 226 271 339 406
4 23 29 35 46 58 70 93 116 140 163 186 210 233 279 349 419
35° 24 30 36 48 60 72 96 120 144 168 192 216 240 288 360 433
6 25 31 37 49 62 74 99 124 149 173 198 223 248 297 371 446
7 25 32 38 51 64 77 102 127 153 178 204 230 255 306 382 459
8 26 33 39 52 66 79 105 131 157 184 210 236 262 315 394 472
9 27 34 40 54 68 81 108 135 162 189 216 243 270 324 405 486
40° 28 35 41 55 70 83 111 139 166 194 222 250 277 333 416 499
1 28 36 43 57 71 86 114 142 171 199 228 256 285 342 427 513
2 29 36 44 58 73 88 117 146 175 205 234 263 293 351 439 527
3 30 37 45 60 75 90 120 150 180 210 240 270 300 360 450 540
4 31 38 46 61 77 93 123 154 185 215 246 277 308 369 462 554
45° 31 39 47 63 79 95 126 158 189 221 253 284 316 379 473 568
6 32 40 48 65 81 97 129 162 194 226 259 291 323 388 485 582
7 33 41 50 66 83 100 133 166 199 232 265 298 331 397 497 597
8 34 42 51 68 85 102 136 170 203 237 272 305 339 407 509 611
9 35 43 52 69 87 104 139 174 208 243 278 313 347 417 521 625
50° 35 44 53 71 89 107 142 178 213 248 284 320 355 426 533 640
1 36 45 54 73 91 109 145 182 218 254 291 327 363 436 545 654
2 37 46 56 74 93 112 148 186 223 260 298 335 372 446 557 669
3 38 47 57 76 95 114 152 190 228 266 304 342 380 456 570 684
4 39 48 58 77 97 117 155 194 233 272 311 350 388 466 582 699
55° 40 49 59 79 99 119 159 198 238 277 318 357 397 476 595 714
6 40 51 61 81 102 122 162 203 243 283 324 365 405 486 608 730
7 41 52 62 83 104 124 166 207 248 289 331 372 414 496 621 745
8 42 53 63 84 106 127 169 211 253 295 338 380 422 507 634 761
9 43 54 64 86 108 130 172 216 259 302 345 388 431 517 647 776
60° 44 55 66 88 110 132 176 220 264 308 352 396 440 528 660 792
1 45 56 67 90 113 135 180 224 269 314 359 404 449 538 673 808
2 46 57 68 91 115 138 183 229 275 320 366 412 458 549 687 824
3 47 58 70 93 117 140 187 233 280 327 373 420 467 560 700 841
4 47 59 71 95 119 143 191 238 286 333 381 429 476 571 714 857
65° 48 61 73 97 121 146 194 243 291 340 388 437 485 582 728 874
6 49 62 74 99 124 149 198 247 297 346 396 445 494 594 742 891
7 50 63 75 101 126 152 202 252 303 353 404 454 504 605 757 908
8 51 64 77 103 129 154 206 257 308 360 411 463 514 617 771 925
9 52 65 78 104 131 157 210 262 314 366 419 471 524 628 786 943
70° 53 67 80 106 134 160 214 267 320 373 427 480 534 640 800 961
1 54 68 81 108 136 163 218 272 326 380 435 489 544 652 815 979
2 55 69 83 110 139 166 222 277 332 387 443 498 554 664 830 997
3 56 70 84 112 141 169 226 282 338 394 451 508 564 676 846 1015
4 57 72 85 115 144 173 230 287 344 402 459 517 574 689 861 1034
75° 58 73 87 117 147 176 234 292 351 409 468 526 585 701 877 1053
6 59 74 89 119 149 179 238 298 357 416 477 536 595 714 893 1072
7 60 76 91 121 152 182 243 303 364 424 485 546 606 727 909 1091
8 62 77 92 123 155 185 247 309 370 432 494 556 617 740 926 1111
9 63 78 94 125 157 189 251 314 377 439 503 565 628 753 942 1131
80° 64 80 96 127 160 192 256 320 384 447 512 576 639 767 959 1151
1 65 81 97 130 163 196 260 325 390 455 521 586 651 781 976 1172
2 66 83 99 132 166 199 265 331 397 463 530 596 662 795 994 1193
3 67 84 101 134 169 203 270 337 404 472 540 607 674 809 1011 1214
4 68 86 103 137 172 206 275 343 411 480 549 618 686 823 1029 1235
85° 70 87 104 139 175 210 279 349 419 488 559 629 698 838 1047 1257
6 71 89 106 142 178 214 284 355 426 497 569 640 710 852 1056 1279
7 72 90 108 144 181 217 289 362 434 506 579 651 723 867 1085 1302
8 73 91 110 147 184 221 295 368 441 515 589 662 736 883 1104 1325
9 75 93 112 149 188 225 300 374 449 524 599 674 749 898 1123 1348
90° 76 95 114 152 191 229 305 381 457 533 610 686 762 914 1143 1372
77
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 78/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
78
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 79/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
79
80
81
82
83
84
T
M
D1
C C
OUTSIDE DISTANCE
NOMINAL SIZE DIA. FROM STD THICKNESS
WEIGHT
(MM) CENTER XS SCHEDULE (MM)
(kg/PC)
XXS T
MM INCH D1=D2 C=M
85
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 86/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
T
M
D1
C C
OUTSIDE DISTANCE
NOMINAL SIZE DIA. FROM STD THICKNESS
WEIGHT
(MM) CENTER XS SCHEDULE (MM)
(kg/PC)
XXS T
MM INCH D1=D2 C=M
20 6.4 22.7
STD - 8.2 27.7
XS - 12.7 34.5
200 8 219.1 177.8 - 120 18.3 52
XXS - 22.23 54.55
- 160 23.0 60
- 30 7 22.8
20 6.4 32
STD - 9.3 41.3
- 80 15.1 68
250 10 273 215.9
XS 12.7 58.5
- 120 21.4 98
- 160 28.6 120
20 6.4 41
STD - 9.5 66.7
- 40 10.3 64
300 12 323.9 254
XS 12.7 84.8
- 80 17.5 91
86
TEE (REDUCING)
(ASTM STANDARD)
ANSI B 16.9
ASTM-A 234
D2
T2 T1
3
M
1 2
D1
C C
87
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 88/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
TEE (REDUCING)
(ASTM STANDARD)
ANSI B 16.9
ASTM-A 234
D2
T2 T1
3
M
1 2
D1
C C
88
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 89/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
TEE (REDUCING)
(ASTM STANDARD)
ANSI B 16.9
ASTM-A 234
D2
T2 T1
3
M
1 2
D1
C C
89
TEE (REDUCING)
(ASTM STANDARD)
ANSI B 16.9
ASTM-A 234 D2
T2 T1
3
M
1 2
D1
C C
8x8x6 200 x 200 x 150 219.1 168.3 177.8 168.3 XS 80 12.7 11.0 34.1
- 160 23.0 18.3 51.82
XXS - 22.2 21.9 51.36
90
TEE (REDUCING)
(ASTM STANDARD)
ANSI B 16.9
ASTM-A 234 D2
T2 T1
3
M
1 2
D1
C C
12 x 12 x 5 300 x 300 x 125 323.9 141.3 254 215.9 XS - 12.7 9.5 75.0
- 160 33.3 15.9 155
91
TEE (REDUCING)
(ASTM STANDARD)
ANSI B 16.9
ASTM-A 234 D2
T2 T1
3
M
1 2
D1
C C
92
EXPANSION JOINT
SHIP’S CAST IRON PIPE SLEEVE TYPE EXPANSION JOINTS
F 3016-1980
UNIT: MM
3 2 4 6
5 1
All o w ab le ex p an sio n
9 8 7
Exam p le: 5k -40
No Component Material
1 Body JIS G 5501-FC 20
5 Gland bush
JIS G 4303-SUS 420 J 2 or JIS H 5111-BC6
6 Gland bush
93
F 3016-1980
UNIT: MM
FLANGE
SLIDING
BOLT HOLE NOMINAL LENGTH
NOMINAL NOM. CYLINDER
SIZE OF FOR
PRESSURE DIA OUTER DIA. OUTER DIA. DIA. OF PITCH SCREW FITTING S
D D1 CIRCLE C DIA. h THREADS
NO. ON BOLT
40 48.6 120 95 4 15 M 12 450
94
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 95/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
F 3017-1980
UNIT: MM
3 2 4 6
5 1
All o w ab le ex p an sio n
9 8 7
Exam p le: 5k -40
No Component Material
5 Gland bush
JIS G 4303-SUS 420 J 2 or JIS H 5111-BC6
6 Gland bush
95
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 96/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
F 3017-1980
UNIT: MM
FLANGE
SLIDING
BOLT HOLE NOMINAL LENGTH
NOMINAL NOM. CYLINDER
SIZE OF FOR
PRESSURE DIA OUTER DIA. OUTER DIA. DIA. OF PITCH SCREW FITTING S
D D1 CIRCLE C DIA. h THREADS
NO. ON BOLT
40 48.6 120 95 4 15 M 12 450
96
1. SCOPE
This standard covers dresser type coupling for electric cable steel pipe.
5. DESIGNATION
WT
MARK ITEM MATERIAL QTY. REMARKS
(kg)
1 MIDDLE RING STEEL SS 41 OR STPG 38 1
97
8
FIG.1 11
5 7 3
2 1 4
9 10
L
H1
1
d2 d-
T N
H2
L2
L1
(ABOUT)
. 35
Ød 15 B
.D
O ØD ØC
E
PI
P
S 10
UNIT : MM
TABLE 1
NOM. PIPE 1 2 4 6 AB’T WT
B
SIZE O.D L (kg)
L1 L2 T d D C H1 H2 MATERIAL N-d1 S N-d2
40 48.6 127 105 5.1 50 120 94 14 6 FCD45 4-M12 175 2-M12 147 230 3.8
50 60.5 127 103 5.5 62 132 106 14 6 FCD45 4-M12 175 2-M12 147 230 4.2
65 76.3 127 103 7.0 78 148 122 15 6 FCD45 4-M12 185 2-M12 150 230 6.2
80 89.1 127 100 7.6 91.5 161 135 18 6 FCD45 4-M12 185 2-M12 154 230 7.8
100 114.3 178 148 8.6 117 198 168 24 7 FCD45 4-M16 240 2-M16 210 330 10.7
125 139.8 178 148 9.5 142 229 197 24 7 FCD45 4-M16 240 2-M16 210 330 17.9
150 165.2 178 134 12.7 168 263 231 25 9 FCD45 6-M16 240 2-M16 213 330 22.6
200 216.3 178 134 12.7 219 320 289 25 9 FCD45 6-M16 240 2-M16 213 330 28.6
250 267.4 178 134 12.7 271 373 339 28 9 FCD45 8-M16 240 2-M16 213 330 33.6
300 318.5 178 134 12.7 322 425 391 29 9 FCD45 8-M16 240 2-M16 213 330 41.6
350 355.6 178 134 12.7 359 473 433 40 13 SS41 8-M16 250 2-M16 216 330 50.2
400 406.4 178 134 12.7 410 524 484 40 13 SS41 10-M16 270 2-M16 225 330 58
98
m 5C
m K.L K.L E
n
C1
FIG 2. m/2 11
FOR NOM.SIZE 40-65
8
d4
10
t
b tR
a
h
3
d
t 9
50 110l 45
m
5C
m E
n
C1
11
FIG 3. d4
FOR NOM.SIZE 8
80 AND OVER t
10
h
b tR
a t
3 9
d
m/2
l
TABLE 2
NOM. 8 11 9 NOM. 8 11 9
SIZE SIZE
mxt l a b E C1 n d3 d4 h mxt l a b E C1 n d3 d4 h
99
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 100/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
1. SCOPE
This standard covers dresser type coupling for electric cable steel pipe.
5. DESIGNATION
WT
MARK ITEM MATERIAL QTY. REMARKS
(kg)
1 MIDDLE RING STEEL SS 41 OR STPG 38 1
101
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 101/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
FIG.1 1 8
4 11
2
9 10
L
H1
1
d-
T N
H2
L2
L1
(ABOUT)
. Ød 35
D. 15 B
O ØD ØC
E
PI
P
S 10
L/2
UNIT : MM
TABLE 1
NOM. PIPE 1 2 4 AB’T WT
B
SIZE O.D L (kg)
L1 L2 T d D C H1 H2 MATERIAL N-d1 S
40 48.6 127 105 5.1 50 120 94 14 6 FCD45 4-M12 175 147 230 3.8
50 60.5 127 103 5.5 62 132 106 14 6 FCD45 4-M12 175 147 230 4.2
65 76.3 127 103 7.0 78 148 122 15 6 FCD45 4-M12 185 150 230 6.2
80 89.1 127 100 7.6 91.5 161 135 18 6 FCD45 4-M12 185 154 230 7.8
100 114.3 178 148 8.6 117 198 168 24 7 FCD45 4-M16 240 210 330 9.9
125 139.8 178 148 9.5 142 229 197 24 7 FCD45 4-M16 240 210 330 17.4
150 165.2 178 134 12.7 168 263 231 25 9 FCD45 6-M16 240 213 330 22.6
200 216.3 178 134 12.7 219 320 289 25 9 FCD45 6-M16 240 213 330 28.6
250 267.4 178 134 12.7 271 373 339 28 9 FCD45 8-M16 240 213 330 33.6
300 318.5 178 134 12.7 322 425 391 29 9 FCD45 8-M16 240 213 330 41.6
350 355.6 178 134 12.7 359 473 433 40 13 SS41 8-M16 250 216 330 50.2
400 406.4 178 134 12.7 410 524 484 40 13 SS41 10-M16 270 225 330 58
450 457.2 178 134 12.7 461 575 535 40 13 SS41 12-M16 270 225 330 66
500 508 178 134 12.7 512 626 586 40 13 SS41 12-M16 270 225 330 71
550 558.8 178 134 12.7 563 677 637 40 13 SS41 14-M16 270 230 330 77
600 609.6 178 134 12.7 614 728 688 40 13 SS41 14-M16 270 230 330 83
650 660.4 178 134 12.7 665 779 739 40 13 SS41 14-M16 270 230 330 90
700 711.2 178 134 12.7 716 830 790 40 13 SS41 16-M16 270 230 330 98
750 762 178 134 12.7 767 881 841 40 13 SS41 16-M16 280 230 330 110
800 812.8 178 134 12.7 818 932 892 40 13 SS41 18-M16 280 230 330 123
850 863.6 178 134 12.7 869 983 943 40 13 SS41 18-M16 280 230 330 131
900 914.4 178 134 12.7 920 1034 994 40 13 SS41 18-M16 280 230 330 142
101
m 5C
m K.L K.L E
n
C1
FIG 2. m/2 11
FOR NOM.SIZE 40-65
8
d4
10
t
b tR
a
h
3
d
t
9
50 110 45
l
m 5C
m E
n
C1
11
FIG 3.
FOR NOM.SIZE
80 AND OVER d4
8 10
t
h
b tR
t
a 9
3
d
m/2
l
UNIT: MM
TABLE 2
NOM. 8 11 9 NOM. 8 11 9
SIZE SIZE
mxt l a b E C1 n d3 d4 h mxt l a b E C1 n d3 d4 h
102
ROD TYPE EXP. JOINT FOR EXHAUST STEAM AND FEED WATER (5K FLANGE)
1. SCOPE
This standard covers rod type expansion joint for exhaust steam and auxiliary feed pump suction.
3. MATERIALS
The material shall be as shown in table 1.
4. PRESSURE RATING
The relation between fluid condition and maximum working pressure are given in the following
table.
5. ALLOWANCE OF EXPANSION
COMPRESSION -20 mm
EXPAND + 10 mm
LATERAL + 5 mm
BODY 12 kg /cm²
103
ROD TYPE EXP. JOINT FOR EXHAUST STEAM AND FEED WATER (5K FLANGE)
5 6 3 2 4
P n-hØ HOLES
1
t1
1t
t2
FLOW
4-8Ø DRILL Ø Ø CØ
d d
DRAIN HOLES
Ø
o
d
T
TOTAL FREE LENGTH 290
SETTING LENGTH 300
UNIT: mm
NOM FLANGE BELLOWS INSIDE TUBE WEIGHT
SIZE D C h n T d P d1 l t1 NLxNo d t2 (kg)
125 235 200 19 8 16 136.6 28 198.2 47 0.8 x 2 196 x 7 120 1.0 25.8
150 265 230 19 8 18 161.2 32 235.2 49 1.0 x 2 192 x 6 145 1.2 28.5
200 320 280 23 8 20 212.3 32 286.3 49 1.0 x 2 192 x 6 196 1.2 31.7
250 385 345 23 12 22 263.4 32 337.4 49 1.0 x 2 192 x 6 248 1.2 45.2
TABLE 1 MATERIAL
6 NUT CARBON STEEL (SS41) 18
WORK SPARE
MARK ITEM MATERIAL REMARKS
QUANTITY
104
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 105/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
ROD TYPE EXP. JOINT FOR EXHAUST STEAM AND FEED WATER (10K FLANGE)
1. SCOPE
This standard covers rod type expansion joint for exhaust steam and auxiliary feed pump suction.
3. MATERIALS
The material shall be as shown in table 1.
4. PRESSURE RATING
The relation between fluid condition and maximum working pressure are given in the following table.
5. ALLOWANCE OF EXPANSION
COMPRESSION -20 mm
EXPAND + 10 mm
LATERAL + 5 mm
BODY 12 kg /cm²
105
ROD TYPE EXP. JOINT FOR EXHAUST STEAM AND FEED WATER (10K FLANGE)
FIG.1
NOM.DIA 50-250
5 6 3 2 1
7
n-hØ HOLES
30
30
P
B.N t1
1t
t2 DoØ
Ø
Ø 1
d d Ø
o
d
T
TOTAL FREE LENGTH 290
4 SETTING BOLT & NUTS
SETTING LENGTH 300
UNIT: mm
NO INSIDE
FLANGE BELLOWS SETTING ROD
M TUBE WT
SIZ BN x (kg)
E D C h n T d P d1 l t1 NLxNo d t2 Bh Do Co
No
200 x
50 155 120 19 4 16 58.5 20 110.5 45 1.0 46 1.0 M12 250 215 M14 x 4 19
10
65 175 140 19 4 18 72.6 24 124.2 49 0.8 x 2 192 x 8 60 1.0 M12 270 235 M14 x 4 23
80 185 150 19 8 18 85.9 28 147.5 47 0.8 x 2 196 x 7 70 1.0 M12 280 245 M16 x 4 26
100 210 175 19 8 18 111.1 28 172.7 47 0.8 x 2 196 x 7 98 1.0 M12 310 270 M16 x 4 30
125 250 210 23 8 20 136.6 28 198.2 47 0.8 x 2 196 x 7 120 1.0 M16 350 310 M20 x 4 45
150 280 240 23 8 22 161.2 32 235.2 49 1.0 x 2 192 x 6 145 1.2 M16 380 340 M20 x 4 51
200 330 290 23 12 22 212.3 32 286.3 49 1.0 x 2 192 x 6 196 1.2 M16 430 390 M20 x 4 56
250 400 355 25 13 24 263.4 32 337.4 49 1.0 x 2 192 x 6 248 1.2 M16 500 460 M20 x 4 74
TABLE 1 MATERIALS
7 STOPPER CARBON STEEL (S G P) 4
WORK SPARE
MARK ITEM MATERIAL REMARKS
QUANTITY
106
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 107/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
TOLERANCE
COUPLING PIPE D x AVE NO OFF IF NO. DIA x STD RING MAX TEST APPROX.
ON O.D L A B C
REF O.D. THICKNESS SPECIFIED LENGTH NO. SUPPLIED PRESSURE WEIGHT
FOR DIST L
MM MM MM MM MM MM MM atm KG
NO IN
IN IN IN IN IN IN IN lbs/in² LBS
44.5 +0.8 -0.40 152 118 146 111 82.5 x 5.6 68 1.7
MU 1 2 0.5 x 5.25 1573 Q
1.75 +0.031 -0.016 6 4.625 5.75 4.375 3.25 x 0.219 1000 3.75
48.3 +0.8 -0.40 152 121 146 111 82.5 x 5.6 68 1.75
MU 1 2 0.5 x 5.25 A1574 Q
1.906 +0.031 -0.016 6 4.75 5.75 4.375 3.25 x 0.219 1000 3.875
MU 57 +0.8 -0.40 152 133 146 121 82.5 x 6.4 1 2 0.5 x 5.25 A 1599 Q 68 2.2
2.25 +0.031 -0.016 6 5.25 5.75 4.75 3.25 x 0.25 1000 4.75
60.3 +0.8 -0.80 152 133 146 121 82.5 x 6.4 68 2.2
MT 1 2 0.5 x 5.25 1500 Q
2.375 +0.031 -0.031 6 5.25 5.75 4.75 3.25 x 0.25 1000 4.75
63 +0.8 -0.80 102 137 172 127 102 x 6.4 68 2.3
MP 1 2 0.5 x 6.25 A 1582 Q
2.48 +0.031 -0.031 4 5.375 6.75 5 4 x 0.25 1000 5.07
70 +0.8 -0.80 102 143.5 172 127 102 x 6.4 68 2.5
MP 1 2 0.5 x 6.25 1565 Q
2.75 +0.031 -0.031 4 5.65 6.75 5 4 x 0.25 1000 5.5
73 +0.8 -0.80 102 148 172 127 102 x 6.4 68 2.6
MP 1 2 0.5 x 6.25 804
2.875 +0.031 -0.031 4 5.812 6.75 5 4 x 0.25 1000 5.75
76.1 +0.8 -0.80 102 148 172 127 102 x 6.4 68 2.6
MP 1 2 0.5 x 6.25 1560 Q
3 +0.031 -0.031 4 5.812 6.75 5 4 x 0.25 1000 5.75
32.5 +0.8 -0.80 102 157.5 172 127 102 x 6.4 68 3.6
MP 1 4 0.5 x 6.25 1567 Q
3.25 +0.031 -0.031 4 6.2 6.75 5 4 x 0.25 1000 8.0
38.9 +0.8 -0.80 102 162 172 127 102 x 6.4 68 3.5
MP 1 3 0.5 x 6.25 1501 Q
3.5 +0.031 -0.031 4 6.375 6.75 5 4 x 0.25 1000 7.75
101.6 +0.8 -0.80 102 176 172 127 102 x 6.4 68 3.9
MP 1 4 0.5 x 6.25 1564 Q
4 +0.031 -0.031 4 6.929 6.75 5 4 x 0.25 1000 8.6
108 +0.8 -0.80 102 184.5 172 127 102 x 6.4 68 4.3
MP 1 4 0.5 x 6.25 A 1596 Q
4.25 +0.031 -0.031 4 7.264 6.75 5 4 x 0.25 1000 9.5
110 +0.8 -0.80 102 184.5 172 127 102 x 6.4 68 4.4
MP 1 4 0.5 x 6.25 1561 Q
4.331 +0.031 -0.031 4 7.264 6.75 5 4 x 0.25 1000 9.62
114.3 +0.8 -0.80 102 192 172 127 102 x 6.4 68 4.4
MP 1 4 0.5 x 6.25 A 1593 Q
4.5 +0.031 -0.031 4 7.562 6.75 5 4 x 0.25 1000 9.62
120.7 +0.8 -0.80 102 195.5 172 127 102 x 6.4 68 4.5
MP 1 4 0.5 x 6.25 549
4.75 +0.031 -0.031 4 7.688 6.75 5 4 x 0.25 1000 10
127 +0.8 -0.80 102 202 172 127 102 x 6.4 68 4.9
MP 1 4 0.5 x 6.25 1538 Q
5 +0.031 -0.031 4 7.937 6.75 5 4 x 0.25 1000 10.75
133 +1.6 -0.80 102 216 172 133 102 x 7.2 68 6.1
MO 1 4 0.5 x 6.25 1563 Q
5.25 +0.062 -0.031 4 8.5 6.75 5.25 4 x 0.281 1000 13.5
140 +1.6 -0.80 102 224 172 133 102 x 7.2 68 6.6
MO 1 4 0.5 x 6.25 A 1598 Q
5.5 +0.062 -0.031 4 8.812 6.75 5.25 4 x 0.281 1000 14.52
141.3 +1.6 -0.80 102 224 172 133 102 x 7.2 68 6.6
MO 1 4 0.5 x 6.25 A 1503 Q
5.562 +0.062 -0.031 4 8.812 6.75 5.25 4 x 0.281 1000 14.52
159 +1.6 -0.80 102 246 172 133 102 x 7.2 61 8.6
LO 1 4 0.5 x 6.25 A 1559 Q
6.25 +0.062 -0.031 4 9.687 6.75 5.25 4 x 0.281 900 19
165.1 +1.6 -0.82 102 252 172 133 102 x 7.2 61 8.8
LO 1 4 0.5 x 6.25 A 1585 Q
6.5 +0.062 -0.032 4 9.937 6.75 5.25 4 x 0.281 900 19.5
LO 168.3
6.625 +1.6
+0.062 -0.84
-0.033 102
4 254
10.143 172
6.75 133
5.25 102 x 7.2
4 x 0.281 1 4 0.5 x 6.25 A 1595 Q 61
900 9
19.75
193.7 +1.6 -0.97 102 281 172 133 102 x 7.2 58 10
LO 1 4 0.5 x 6.25 A 1507 Q
7.625 +0.062 -0.038 4 11.062 6.75 5.25 4 x 0.281 850 22
219.1 +1.6 -1.0 102 309 172 133 102 x 7.2 58 11.6
LO 1 5 0.5 x 6.25 A 1597 Q
8.628 +0.062 -0.039 4 12.187 6.75 5.25 4 x 0.281 850 25.5
107
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 108/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
TOLERANCE
COUPLING PIPE D x AVE NO OFF IF NO. DIA x STD RING MAX TEST APPROX.
ON O.D L A B C
REF O.D. THICKNESS SPECIFIED LENGTH NO. SUPPLIED PRESSURE WEIGHT
FOR DIST L
MM MM MM MM MM MM MM atm KG
NO IN
IN IN IN IN IN IN IN lbs/in² LBS
244.5 +1.6 -1.0 102 337 172 133 102 x 8.7 54 14.1
KN 2 6 0.5 x 6.25 1511 Q
9.625 +0.062 -0.039 4 13.25 6.75 5.25 4 x 0.344 800 31
273 +1.6 -1.0 102 367 172 133 102 x 8.7 47 15.4
KN 2 6 0.5 x 6.25 A 1557 Q
10.75 +0.062 -0.039 4 14.437 6.75 5.25 4 x 0.344 700 34
273 +1.6 -1.0 152 397 273 235 178 x 11.1 98 30.8
A2E 2 12 0.625 x 9.75 J 132 M
10.75 +0.062 -0.034 6 15.67 10.75 9.25 7 x 0.437 1438 68.0
KN 323.9 +1.6 -1.0 102 419 172 133 102 x 8.7 2 8 0.5 x 6.25 A 1558 Q 47 18.6
12.75 +0.062 -0.039 4 16.5 6.75 5.25 4 x 0.344 700 41
323.9 +1.6 -1.0 152 448 273 235 178 x 11.1 83 35.8
A2E 2 12 0.625 x 9.75 J 101 M
12.75 +0.062 -0.034 6 17.68 10.75 9.25 7 x 0.437 1220 79.0
355.6 +1.6 -1.6 152 460 254 216 178 x 8.7 46.6 31.1
CF6 2 6 0.625 x 9.5 J 51 L
14 +0.062 -0.062 6 18.11 10 8.5 7 x 0.344 675 68.5
355.6 +1.6 -1.6 152 460 254 216 178 x 8.7 77.7 32.9
CF10 2 10 0.625 x 9.5 J 51 L
14 +0.062 -0.062 6 18.11 10 8.5 7 x 0.344 1125 72.5
355.6 +1.6 -1.6 152 480 273 235 178 x 11.1 106.4 51.5
A2E 2 18 0.625 x 10.25 J 102 M
14 +0.062 -0.062 6 18.897 10.75 9.25 7 x 0.437 1540 113.5
406.4 +1.6 -1.6 152 511 254 216 178 x 8.7 40.7 34.7
CF6 2 6 0.625 x 9.5 J 53 L
16 +0.062 -0.062 6 20.125 10 8.5 7 x 0.344 590 76.5
406.4 +1.6 -1.6 152 511 254 216 178 x 8.7 68.4 36.7
CF10 2 10 0.625 x 9.5 J 53 L
16 +0.062 -0.062 6 20.125 10 8.5 7 x 0.344 990 81
406.4 +1.6 -1.6 152 530 273 235 178 x 11.1 92.9 56.9
A2E 2 18 0.625 x 10.25 J 104 M
16 +0.062 -0.062 6 20.866 10.75 9.25 7 x 0.437 1345 125.5
457 +1.6 -1.6 152 562 254 216 178 x 8.7 48.7 39.5
CF8 3 8 0.625 x 9.5 J 55 L
18 +0.062 -0.062 6 22.125 10 8.5 7 x 0.344 705 87
457 +1.6 -1.6 152 562 254 216 178 x 8.7 60.8 40.4
CF10 3 10 0.625 x 9.5 J 55 L
18 +0.062 -0.062 6 22.125 10 8.5 7 x 0.344 880 89
457 +1.6 -1.6 152 581 273 235 178 x 11.1 82.5 62.4
A2E 3 18 0.625 x 10.25 J 106 M
18 +0.062 -0.062 6 22.874 10.75 9.25 7 x 0.437 1195 137.5
508 +1.6 -1.6 152 613 254 216 178 x 8.7 54.9 44.2
CF 3 10 0.625 x 9.5 J 57 L
20 +0.062 -0.062 6 24.125 10 8.5 7 x 0.344 795 97.5
508 +1.6 -1.6 152 632 273 235 178 x 11.1 74.2 67.8
A2E 3 18 0.625 x 10.25 J 108 M
20 +0.062 -0.062 6 24.881 10.75 9.25 7 x 0.437 1075 149.5
559 +1.6 -1.6 152 664 254 216 178 x 8.7 50.1 47.8
CF 3 10 0.625 x 9.5 J 59 L
22 +0.062 -0.062 6 26.125 10 8.5 7 x 0.344 725 105.5
559 +1.6 -1.6 152 683 273 235 178 x 11.1 67.7 73.3
A2E 3 18 0.625 x 10.25 J 110 M
22 +0.062 -0.062 6 26.889 10.75 9.25 7 x 0.437 980 161.5
610 +1.6 -1.6 152 714 254 216 178 x 8.7 45.9 51.5
CF 3 10 0.625 x 9.5 J 60 L
24 +0.062 -0.062 6 28.125 10 8.5 7 x 0.344 665 113.5
610 +1.6 -1.6 152 734 273 235 178 x 11.1 61.8 78.7
A2E 3 18 0.625 x 10.25 J 111 M
24 +0.062 -0.062 6 28.897 10.75 9.25 7 x 0.437 895 173.5
660 +1.6 -1.6 152 765 254 216 178 x 8.7 12.5 55.3
CF 3 10 0.625 x 9.5 J 61 L
26 +0.062 -0.062 6 30.125 10 8.5 7 x 0.344 615 122
660 +1.6 -1.6 152 784 273 235 178 x 11.1 57.0 84.1
A2E 3 18 0.625 x 10.25 J 112 M
26 +0.062 -0.062 6 30.866 10.75 9.25 7 x 0.437 825 185.5
CF 711 +1.6 -1.6 152 816 254 216 178 x 8.7 3 10 0.625 x 9.5 J 63 L 39.4 58.9
28 +0.062 -0.062 6 32.125 10 8.5 7 x 0.344 570 130
711 +1.6 -1.6 152 835 273 235 178 x 11.1 53.2 89.6
A2E 3 18 0.625 x 10.25 J 113 M
28 +0.062 -0.062 6 32.874 10.75 9.25 7 x 0.437 770 197.5
762 +1.6 -1.6 152 871 254 222 178 x 8.7 38.7 73.5
YF 3 12 0.625 x 9.5 J 64 L
30 +0.062 -0.062 6 34.291 10 8.75 7 x 0.344 560 162
762 +1.6 -1.6 152 886 273 235 178 x 11.1 49.4 95.3
A2E 3 18 0.625 x 10.25 J 115 M
30 +0.062 -0.062 6 34.881 10.75 9.25 7 x 0.437 715 210
813 +1.6 -1.6 152 922 254 222 178 x 8.7 36.3 77.8
YF 3 12 0.625 x 9.5 J 65 L
32 +0.062 -0.062 6 36.299 10 8.75 7 x 0.344 525 171.5
813 +1.6 -1.6 152 937 273 235 178 x 11.1 46.3 100.7
A2E 3 18 0.625 x 10.25 J 123 M
32 +0.062 -0.062 6 36.889 10.75 9.25 7 x 0.437 670 222
864 +1.6 -1.6 152 973 254 222 178 x 8.7 34.2 82.1
YF 3 12 0.625 x 9.5 J 66 L
34 +0.062 -0.062 6 38.307 10 8.75 7 x 0.344 495 181
864 +1.6 -1.6 152 988 273 235 178 x 11.1 43.5 106.1
A2E 3 18 0.625 x 10.25 J 116 M
34 +0.062 -0.062 6 38.897 10.75 9.25 7 x 0.437 630 234
914 +1.6 -1.6 152 1024 254 222 178 x 8.7 32.5 86.4
YF 3 12 0.625 x 9.5 J 67 L
36 +0.062 -0.062 6 40.315 10 8.75 7 x 0.344 470 190.5
914 +1.6 -1.6 152 1038 273 235 178 x 11.1 41.1 111.6
A2E 3 18 0.625 x 10.25 J 117 M
36 +0.062 -0.062 6 40.866 10.75 9.25 7 x 0.437 595 246
1016 +1.6 -1.6 152 1125 254 222 178 x 8.7 29.0 95.9
YF 3 14 0.625 x 9.5 J 71 L
40 +0.062 -0.062 6 44.291 10 8.75 7 x 0.344 420 211.5
1016 +1.6 -1.6 152 1140 273 235 178 x 11.1 37.0 122.5
A2E 3 18 0.625 x 10.25 J 119 M
40 +0.062 -0.062 6 44.882 10.75 9.25 7 x 0.437 535 270
1067 +1.6 -1.6 152 1176 254 222 178 x 8.7 27.6 100.2
YF 3 14 0.625 x 9.5 J 72 L
42 +0.062 -0.062 6 46.299 10 8.75 7 x 0.344 400 221
1067 +1.6 -1.6 152 1191 273 235 178 x 11.1 35.2 127.9
A2E 3 18 0.625 x 10.25 J 119 M
42 +0.062 -0.062 6 46.889 10.75 9.25 7 x 0.437 510 282
1118 +1.6 -1.6 152 1227 254 222 178 x 8.7 26.6 104.5
YF 3 14 0.625 x 9.5 J 73 L
44 +0.062 -0.062 6 48.307 10 8.75 7 x 0.344 385 230.5
1118 +1.6 -1.6 152 1242 273 235 178 x 11.1 33.8 133.3
A2E 3 18 0.625 x 10.25 J 120 M
44 +0.062 -0.062 6 48.897 10.75 9.25 7 x 0.437 490 294
1220 +1.6 -1.6 152 1343 273 235 178 x 11.1 30.7 144.2
A2E 3 18 0.625 x 10.25 J 121 M
48 +0.062 -0.062 6 52.874 10.75 9.25 7 x 0.437 445 318
1220 +1.6 -1.6 152 1350 286 238 178 x 14.3 37.6 173.3
AD 3 24 0.625 x 10.75 J 176 H
48 +0.062 -0.062 6 53.149 11.25 9.375 7 x 0.563 545 382
1270 +1.6 -3.2 152 1394 273 235 178 x 11.1 29.7 149.7
A2E 3 18 0.625 x 10.25 J 122 M
50 +0.062 -0.125 6 54.882 10.75 9.25 7 x 0.437 430 330
AD 1270
50 +1.6
+0.062 -3.2
-0.125 152
6 1400
55.118 286
11.25 238
9.375 178 x 14.3
7 x 0.563 3 24 0.625 x 10.75 J 176 H 36.3
525 179.8
396.5
1321 +1.6 -3.2 152 1445 273 235 178 x 11.1 28.3 155.4
A2E 3 18 0.625 x 10.25 J 124 M
52 +0.062 -0.125 6 56.889 10.75 9.25 7 x 0.437 410 342.5
1321 +1.6 -3.2 152 1451 286 238 178 x 14.3 34.9 186.2
AD 3 24 0.625 x 10.75 J 177 H
52 +0.062 -0.125 6 57.125 11.25 9.375 7 x 0.563 505 410.5
108
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 109/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
109
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 110/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
PENETRATION PIECE
SHIP’S 5K AND 10K DECK AND BULKHEAD PIECES FOR PIPE CONNECTION (JIS F 3009)
1
OD
OC
Unit : mm
5K 10K
FLANGE FLANGE
NOM. OUTSIDE
DIA BOLT HOLE DIA.
DIA OF THREAD THREAD
PIPE DIA OF DIA OF
PITCH NO DIA. ON BOLT PITCH NO DIA. ON BOLT
CIRCLE CIRCLE
D t C h (D1) l D t C h (D1) l
50 60.5 130 14 105 4 15 M12 185 100 155 16 120 4 19 M16 210 100
65 76.3 155 14 130 4 15 M12 210 100 175 18 140 4 19 M16 230 100
80 89.1 180 14 145 4 19 M16 235 100 185 18 150 8 19 M16 240 100
(90) 101.6 190 14 155 4 19 M16 245 100 195 18 160 8 19 M16 250 100
100 114.3 200 16 165 8 19 M16 255 100 210 18 175 8 19 M16 265 100
125 139.8 235 16 200 8 19 M16 290 120 250 20 210 8 23 M20 305 120
150 165.2 265 18 230 8 19 M16 370 120 280 22 240 8 23 M20 385 120
200 216.3 320 20 280 8 23 M20 425 120 330 22 290 12 23 M20 435 120
Remarks: 1. Plate thickness (t1) of item No. 2 shall, as a rule, to be equivalent to the thickness (t2) of wall to
be fitted or more (t1> t2).
2. When fitted to division for fire protection or where thermal insulation is applied, dimension l shall
be extended as necessary.
TABLE 2
NO COMPONENT MATERIAL
110
1. SCOPE : This standard cover penetrating sleeve used for copper pipe
L
STEEL SLEEVE BRASS BRAZING
(SS41) OR TIG WELD
C D.
COPPER PIPE IA
ØD Ød O
D
E
PI T
P CU
W DK OR B.H.D
111
1 BULKHEAD OR
CONDUIT DECK 2 CARBON STEEL
MADE FROM FLANGE
SEAM JOINT
STEEL PIPE
BY BRAZING
CSD SEALING
5
PLUG FRR
4 COPPER
S NICKEL
INNER
FLANGE
(WELDING
COLLAR)
DIMENSION
MATERIALL LIST
112
CARBON STEEL
5 BULKHEAD OR DECK
MIDDLE FLANGE
L4
COPPER NICKEL
4
SLEEVE
L2
d2
S1
d1 d6 ØK
COPPER NICKEL
3
COPPER NICKEL PIPE
2 CARBON STEEL
INNER FLANGE 1
OUTER FLANGE
WEIGHT
OUTSIDE DIA BOLT
d6 a L4 S1 L2 d1 k d2 kg/STUCK
OF PIPE HOLES
PN Kg/PIECE
NOM NOM
MM MM MM MM MM MM MM MM MM MM
MM MM
20 25 86 62 4 11
25 30 92 68 4 11
MATERIALL LIST
113
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 114/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
A B
80R 70R 80R 105R 100R 150R 185R 230R 270R 345R 420R 500R 650R
10Ø 15Ø 20Ø 25Ø 32Ø 40Ø 50Ø 65Ø 80Ø 100Ø 125Ø 150Ø 200Ø
E
E
R A B C A B C A B C A B C A B C A B C A B C A B C A B C A B C A B C A B C A B C
G
E 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
D 0 5 1 0 5 1 0 5 1 0 5 1 5 5 2 1 2 5 1 2 5 3 5 5 6 3 8 8 0 2 6 5 6 3 3 3 3 7 3
7 1 1 7 1 1 7 1 1 7 1 1 8 1 1 1 1 1 1 1 1 1 2 2 1 2 2 1 3 3 2 3 2 3 4 3 4 4 4
AL H AL H AL H AL H AL H AL H AL H AL H AL H AL H AL H AL H AL H
1° 1 1 1 1 1 1 2 1 2 1 3 1 3 2 4 2 4 2 6 3 7 4 8 5 11 5
2° 2 1 2 1 3 1 4 2 3 2 5 3 7 3 8 4 9 5 12 6 14 7 17 10 22 11
3° 4 2 4 2 4 2 6 3 5 3 7 4 10 5 12 6 15 7 18 9 20 10 25 14 33 17
4° 5 3 5 2 5 3 8 4 7 4 9 5 13 7 16 8 18 9 23 12 28 15 33 18 44 23
5° 7 4 6 3 7 4 9 5 8 4 12 7 16 8 19 11 23 12 29 15 35 18 42 22 55 28
6° 8 4 7 4 8 4 11 6 10 5 15 8 20 10 23 12 27 14 35 18 42 22 50 26 65 34
7° 9 5 8 4 10 5 13 7 12 6 17 9 23 11 27 14 31 17 41 21 48 26 59 31 76 40
8° 10 6 9 5 11 6 15 7 13 7 20 10 26 14 31 16 36 19 47 24 56 29 66 35 87 45
9° 12 6 10 6 12 6 16 8 15 8 23 12 29 15 35 18 40 21 52 27 63 33 75 39 98 51
10° 14 7 12 6 14 7 18 9 17 9 26 13 31 16 39 20 46 24 58 30 70 37 84 44 109 57
11° 15 8 13 7 15 8 20 10 18 10 28 14 35 18 43 22 50 26 64 33 78 40 92 48 120 62
12° 16 8 14 7 16 8 21 11 20 11 31 16 38 20 47 24 55 28 70 36 84 44 100 53 131 68
13° 17 9 15 8 18 9 23 12 22 11 33 17 41 21 50 26 59 31 76 39 91 48 109 57 142 74
14° 18 10 16 9 19 10 25 13 23 12 36 18 44 23 54 28 64 33 82 42 99 52 118 61 153 79
15° 21 10 18 9 20 11 27 14 25 13 39 20 47 24 58 30 68 36 89 45 105 55 126 66 164 85
16° 21 11 18 10 22 11 28 15 27 14 42 21 50 26 62 32 72 38 93 48 110 59 134 70 175 91
17° 22 12 19 10 23 12 30 16 28 15 44 22 53 28 66 34 77 40 99 52 118 63 142 75 185 97
18° 23 13 20 11 24 13 32 17 30 16 47 24 57 29 70 36 82 43 105 55 125 67 150 79 196 103
19° 24 13 21 12 26 13 34 18 32 17 49 25 60 31 74 38 86 45 111 58 132 70 158 84 207 109
20° 26 14 22 12 27 14 35 19 33 18 52 26 63 33 78 41 90 48 116 61 139 74 166 88 218 113
21° 28 15 24 13 28 15 37 20 35 19 54 28 66 34 81 43 95 50 122 64 147 78 176 93 229 120
22° 29 16 25 14 30 16 39 21 37 19 57 29 68 36 85 45 99 52 128 67 154 82 182 97 240 126
23° 30 16 26 14 31 16 41 22 39 20 59 31 72 38 89 47 103 55 134 70 162 85 190 102 251 132
24° 32 17 28 15 32 17 43 23 40 21 62 32 75 39 92 49 108 57 140 73 169 89 198 106 262 138
25° 34 18 30 16 34 18 44 24 42 22 64 33 78 41 97 51 113 60 146 77 174 93 208 111 273 144
26° 36 18 31 16 35 19 46 25 44 23 67 35 81 43 101 53 118 62 151 80 183 97 214 115 284 150
27° 37 19 32 17 37 19 48 26 45 24 69 36 85 44 105 55 123 65 157 83 190 101 222 120 295 156
28° 38 20 33 17 38 20 50 27 47 25 72 37 88 46 108 57 128 67 163 86 197 105 231 125 306 162
29° 40 20 34 18 39 21 52 28 49 26 75 39 91 48 112 59 132 70 169 89 205 109 242 129 317 168
30° 41 21 35 19 41 21 53 29 50 27 77 40 94 50 116 62 137 72 175 92 211 113 251 134 328 174
31° 42 22 36 19 42 22 55 30 51 28 80 42 97 51 120 64 141 75 180 96 217 116 259 139 338 180
32° 43 23 37 20 43 23 57 31 54 29 82 43 100 53 124 66 146 77 186 99 224 120 267 143 349 186
33° 44 24 38 21 45 24 59 32 55 30 85 44 103 55 128 68 150 80 192 102 231 124 276 148 360 192
34° 45 24 39 21 46 25 61 33 57 31 87 46 107 57 132 70 155 83 198 106 238 128 284 153 371 198
35° 46 25 40 22 47 25 62 34 59 32 90 47 110 58 136 73 160 85 204 109 244 132 292 158 382 205
36° 47 26 41 23 49 26 64 35 60 33 92 49 113 60 140 75 164 88 210 112 251 136 301 162 393 211
37° 49 27 42 23 50 27 66 36 62 34 95 50 116 62 143 77 168 90 215 115 259 141 309 167 404 217
38° 50 28 43 24 51 28 68 37 64 34 99 52 119 64 147 79 173 93 221 119 267 145 317 172 415 224
39° 52 28 45 25 53 28 69 38 65 35 100 53 122 65 151 81 177 96 227 122 274 149 326 177 426 230
40° 53 29 46 25 54 29 71 39 67 36 102 55 126 67 155 84 181 98 233 126 281 153 334 182 437 237
41° 54 30 47 26 55 30 73 40 69 37 105 56 129 69 159 86 186 101 239 129 286 157 343 187 449 243
42° 55 31 48 27 57 31 75 41 70 38 107 58 132 71 163 88 191 104 244 132 301 161 351 192 458 250
80R 70R 80R 105R 100R 150R 185R 230R 270R 345R 420R 500R 650R
10Ø 15Ø 20Ø 25Ø 32Ø 40Ø 50Ø 65Ø 80Ø 100Ø 125Ø 150Ø 200Ø
E
E
R A B C A B C A B C A B C A B C A B C A B C A B C A B C A B C A B C A B C A B C
G
E 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
D 0 5 1 0 5 1 0 5 1 0 5 1 5 5 2 1 2 5 1 2 5 3 5 5 6 3 8 8 0 2 6 5 6 3 3 3 3 7 3
7 1 1 7 1 1 7 1 1 7 1 1 8 1 1 1 1 1 1 1 1 1 2 2 1 2 2 1 3 3 2 3 2 3 4 3 4 4 4
AL H AL H AL H AL H AL H AL H AL H AL H AL H AL H AL H AL H AL H
43° 58 32 50 28 58 32 76 42 72 39 110 59 135 73 167 91 196 106 250 136 306 165 360 197 469 256
44° 60 32 52 28 59 32 78 43 74 40 112 61 138 75 171 93 200 109 256 139 312 170 368 202 480 263
45° 62 33 54 29 61 33 80 44 75 41 115 62 142 77 174 95 204 112 262 143 318 174 378 207 491 269
46° 64 34 56 30 62 34 82 45 77 42 117 64 145 79 178 98 209 115 268 146 324 178 386 212 502 276
47° 65 35 57 30 64 35 84 46 79 44 120 65 148 80 182 100 213 117 274 150 330 183 394 217 513 283
48° 66 36 58 31 65 36 85 47 80 45 122 67 151 82 186 102 218 120 279 154 336 187 403 223 524 290
49° 68 36 60 32 66 36 87 48 82 46 125 68 154 84 190 105 222 123 285 157 343 191 411 228 535 296
50° 69 37 62 33 68 37 89 49 84 47 127 70 157 86 194 107 227 126 291 161 350 196 420 233 546 303
51° 71 38 64 33 69 38 91 50 85 48 130 72 160 88 198 110 231 129 297 165 357 200 428 238 556 310
52° 72 39 65 34 71 39 92 51 87 49 132 73 163 90 202 113 236 132 303 168 364 205 437 243 567 317
53° 74 40 66 35 72 40 94 52 89 50 135 75 166 92 206 115 241 135 309 172 371 209 445 249 578 325
54° 75 41 67 36 73 41 96 53 90 51 137 76 170 94 210 117 244 138 314 176 378 214 454 255 589 332
55° 76 42 68 36 74 42 98 55 92 52 140 78 173 96 214 120 249 141 320 180 385 219 462 260 601 339
56° 78 43 70 37 76 43 100 56 94 53 142 80 176 98 217 122 254 144 326 183 392 223 470 266 612 346
57° 79 43 71 38 77 43 101 57 95 54 145 81 179 100 221 125 259 147 332 187 400 228 478 271 622 354
58° 81 44 72 39 78 44 103 58 97 55 147 83 182 102 225 127 263 150 338 191 407 233 487 277 633 360
59° 82 45 73 40 80 45 105 59 99 57 150 85 185 105 229 130 269 153 343 195 414 238 495 283 644 368
60° 83 46 74 40 81 46 107 61 1 00 58 153 87 189 107 232 133 273 156 349 199 421 242 503 289 655 378
61° 85 47 75 41 82 47 108 62 1 02 59 155 88 192 109 236 135 277 159 355 203 426 247 511 295 666 383
62° 86 48 76 42 84 48 110 63 1 04 60 158 90 195 111 240 138 281 162 361 207 433 252 518 300 677 390
63° 88 49 77 43 85 49 112 64 1 06 61 160 92 197 113 244 141 286 165 367 211 441 257 526 306 688 398
64° 89 50 78 44 86 50 114 66 1 07 62 163 94 200 115 248 144 291 169 374 216 448 262 534 312 699 406
65° 90 51 79 45 88 51 116 67 1 09 64 166 96 202 118 252 146 294 172 378 220 455 268 543 319 710 414
66° 92 52 80 45 89 52 117 68 1 11 65 169 97 206 120 256 149 299 175 384 224 462 273 552 325 720 422
67° 93 53 81 46 91 53 119 70 1 12 66 171 99 210 122 260 152 304 179 390 228 469 278 561 331 731 430
68° 94 54 82 47 92 54 121 71 114 68 174 101 214 125 264 155 309 182 396 233 476 283 569 337 742 438
69° 96 55 83 48 93 55 123 72 116 69 176 103 217 127 268 158 314 186 402 237 483 289 578 344 753 446
70° 97 56 84 49 95 56 124 74 117 70 179 105 220 129 272 161 318 189 407 242 492 294 585 350 764 455
71° 99 57 85 50 96 57 126 75 119 71 181 107 223 132 275 164 323 193 413 246 500 300 594 357 775 466
72° 100 58 86 51 97 58 128 76 1 21 73 183 109 226 134 279 167 327 196 419 251 507 305 602 363 786 472
73° 101 59 87 52 99 59 130 78 1 22 74 186 111 229 137 283 170 332 200 425 255 515 311 611 370 796 480
74° 103 60 88 53 1 00 60 132 79 1 24 75 188 113 232 139 287 173 337 203 431 260 522 316 619 377 807 491
75° 104 61 89 54 1 01 61 133 81 1 26 77 191 115 236 142 291 177 341 207 437 265 530 322 628 384 818 499
76° 106 63 90 55 1 03 63 135 82 1 27 78 194 117 238 145 294 180 345 211 442 270 536 328 636 391 830 508
77° 107 64 91 56 1 04 64 137 84 1 29 80 196 119 242 147 299 183 350 215 448 274 544 334 642 398 841 518
78° 108 65 92 57 1 05 65 139 85 1 31 81 199 121 245 150 302 186 355 219 454 279 550 340 654 405 852 527
79° 110 66 93 58 1 07 66 140 87 1 32 82 201 124 248 152 306 190 359 223 460 284 558 346 662 412 862 536
80° 111 67 94 59 1 08 67 142 88 1 34 84 204 126 251 155 310 193 363 227 466 289 565 352 670 420 873 545
81° 113 68 95 60 1 09 68 144 90 1 36 85 207 128 254 158 314 196 368 231 471 295 572 359 680 427 884 556
82° 114 70 96 61 1 11 70 146 91 1 37 87 209 130 258 160 318 200 373 235 477 300 579 365 690 435 895 565
83° 115 71 97 62 1 12 71 148 93 1 39 89 212 133 260 163 322 204 378 239 483 305 586 372 697 442 905 576
84° 117 72 99 63 1 13 72 149 95 1 41 90 214 135 264 166 326 207 383 245 489 311 594 378 706 450 916 586
85° 118 7 3 101 64 115 73 151 96 142 92 2 17 137 267 169 330 210 387 247 495 316 600 385 715 458 928 596
86° 120 7 5 103 65 116 75 153 98 144 93 2 20 140 270 172 334 214 391 252 501 322 608 392 722 466 939 606
87° 121 76 105 66 118 76 155 100 146 95 2 22 142 273 175 338 218 395 256 506 328 614 399 731 474 949 617
88° 122 77 107 68 119 77 156 101 147 97 2 25 145 276 178 342 222 399 261 512 333 622 406 740 483 960 628
89° 124 79 108 69 120 79 158 103 149 98 2 27 147 279 183 345 226 404 265 518 339 630 413 750 491 971 638
90° 125 80 110 70 122 80 160 105 151 100 229 150 283 185 349 230 409 270 524 345 636 420 758 500 982 650
115
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 116/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
θ θ
( AL = x 2πR) (H = R x Tan )
360 2
BEND R 60R 70R 85R 100R 125R 150R 150R 225R 255R 305R 320
CLAMP L A B C A B C A B C A B C A B C A B C A B C A B C A B C A B C A B
0 0 0 0 0 0 0 5 0 0 0 5 0 0 0 0 0 0
0 0 5
MARK 5
6
5
6
5
0 0 0 1 0 2 5 1 5 3 0 6 0 4 0 5
1 1 2 1 1 1 1 1 1 1 1 1 2 1 3 1 3 1
ANGLE AL H AL H AL H AL H AL H AL H AL H AL H AL H AL H AL
5° 5 3 6 3 7 4 8 5 11 6 12 7 12 7 20 10 22 11 27 13 28
10° 10 5 12 6 14 7 18 9 22 11 26 13 26 13 39 20 45 22 53 27 56
15 16 8 18 9 21 11 26 13 33 16 39 20 39 20 59 30 67 34 80 40 84
50° 52 28 61 33 72 40 87 47 109 52 127 70 127 70 197 105 222 119 266 142 279
55° 58 31 67 37 79 44 96 52 120 65 140 78 140 78 216 117 244 133 293 159 307
60° 63 35 73 40 87 49 104 58 131 73 153 87 153 87 236 130 267 147 319 176 335
65° 68 38 79 45 94 54 115 64 143 80 166 96 166 96 257 143 292 163 346 194 366
70° 73 42 86 49 101 60 123 70 154 88 179 105 179 105 277 157 314 179 373 214 395
75° 79 46 92 54 109 65 130 77 164 96 191 115 191 115 296 178 334 196 399 234 420
80° 84 50 98 59 118 71 140 84 174 105 204 126 204 126 316 188 356 214 426 256 447
85° 89 55 104 64 126 78 149 94 187 115 217 137 217 137 337 203 382 234 452 279 478
90° 94 60 110 70 134 85 157 100 196 125 229 150 229 150 356 225 400 255 479 305 502
117
CASE 1
α
P V
θ
BENDING ANGLES
X Cosθ XCosθ
Cos α = =
(V² + X²) P
V
Tanβ =
X
TWIST ANGLES
± 90°
117
CASE II
α
θ
β P V
BENDING ANGLES
X Sinθ XSinθ
Cosα = =
(V² + X²) P
β = 90°
TWIST ANGLES
V Tan θ
Tan λ =
P
118
CASE III
β
V
P Ø
Z
θ
α
BENDING ANGLES
Z Cos θ ZCosθ
Cos α = =
(V² + Z² P
Z Cos φ Z Cos φ
Cos β = =
P
(V² + Z²
Cos 2φ = (V/Z)²
TWIST ANGLES
V Tan θ
Tan λ = λ = λ −λ
2 P 2 1
119
CASE IV
BENDING ANGLES
IN TERM OF ANGLE θ
WHEN θ ≠ 90°
X − Y Cosθ
Cos α =
( V ² + Z ²)
Y − X Cosθ
Cosβ =
( V ² + Z²)
P
α Z β Y − X Cosθ
V y =
θ
P
WHEN θ = 90°
X
X Y
Cosα = =
( V ² + Z ²) P
Y Y
Cosβ = =
( V ² + Z ²) P
TWIST ANGLES
VZ
( X Sinα)² + ( Y Sinβ)² − ( )²
Cosλ = P
2( X Sinα)( Y Sinβ)
α Z CosΦ Z CosΦ
Cosα = =
P β ( V ² + Z²) P
V Z ρ y
θ Z Cosρ Z Cosρ
φ Cosβ = =
( V ² + Z²) P
X
Cos 2Φ = ( V Z )² = Cos 2ρ
WHEN θ = 90°
V²
Cos 2Φ = = Cos 2ρ
Y ² + X²
120
CASE IV
BENDING ANGLES
Z Cosθ Z Cosθ
Cosα = =
( V ² + X²) P
β = 90°
V
P
TWIST ANGLES
V
Tanλ =
P Tanθ
α θ z
θ < 90° 0° + λ
θ > 90° 0° + ( − λ )
α = 90°
β = 90°
Y BENDING ANGLES
φ CosΦ = V² Z²
−
V V² + Z²
V
FINDING LENGTH Y AND X
z
Z
θ X=Y=
Sin Φ
TWIST ANGLES
λ = 0° + (180° − θ)
121
TWIST BEND
ANGLE ANGLE
+90°
PIPE
0°
BENDER
180°
NOTE
-90° 1. TWIST ANGLE OF SIDE L 1 & 3 IS INDICATE
TWIST ANGLE OF FLANGE.
45° 2
45°
122
K3
H3
d
K1 AL3
H1 H2 c
AL
1
K2
AL
2
K
a
GRIPPING
A
B
a = K − H1
b = K 1 − H1 − H 2 + AL 1
c = K 2 − H 2 − H 3 + AL 2
d = K 3 − H 3 + AL 3
C
NOTE: ALLOWANCE
Usually b > c > a
2
K
H
2 c
a = K − H1
2 b = K 1 − H1 − H 2 + AL 1
AL
c = K 2 − H 2 + AL 2
K1
b
L1
A
a
H1
123
T
S
U
N R-
OI T I
° ° E T
T ° 4 ° 2 900 S N
C 1 7 1 7 1 A
REI 1 1
3L 2L
D R
0 0 E
H C 5 0
3
0
6 MI
. R
Y P
T
9
8 Q
N 0 0 0 0 L s
e
IO 0 2 7 4 A rr
2 5 0 5 T e t
in
TI 2 3 3 C a
S = = = = O ti. P
O 1 1 1 1 D T T n
P L L L L N NI A
E O
B P T
L SB 4 N
C 4
° is E
G 3 s
e t M
E 1
R ni T
L t a A
a P E
D G e
N IN H Ø Ø Ø Ø H R
E T T
D G 0 7 T 5 5 5 5 E
E L 0 0 0 0 6 6 6 6 L
N PI
1
P E N - - - - 4010
PI W LE 3 2 OIJ 1 1 1 1 n P
S S S S oi
t
T al
. NI 3540 0 u
s
0
D 'G O
0
7 2 In
N L J F A 3 0
E F 3 0
2
K E E 5
N V G 2
E N E 4
A E N - H
P L L A - T g
O B S L G ni
= = F S S N in .
= = 0 9 E L V
L
O X S F 0 3 0 0 L 4 4 4 4 A
6 7 . 4 9 4 4 G
H 1 1 1 2 E
C DI
N S
.
A T
T R el U
NI T 2 B k O
ic :
O NI 0 5 P M
P O 8- 6-
P 1 1 K
G - S 5 . 172°
NI G 1
R IA
T NI D c c c c
R D B 0 0 . 5 5 5 5 174°
- 1 4 0 .
TA NE C 04 73 0 9 MO 6 6 6 6 lva
S S N G
0
8
°
1
S F
1 S
S m
c/
T C O g Y
B .k IT
NI pi t . °) P.
T
O H r u
2 O H 4 15
0 200
T.
J T :r :C
G C T T T 31 N
G e w T D N ( 250
W A
N d o SI N A Y U
n lb E Q
E e E R
K L B W B B
E R
T g
nli
PI A a
N P e
OI M n
n
T 7 1 4 1 1 A
A 5
6 .0 0
L B 7 2
U R 0
C G 8 T .
L L H SI
p
s
A 5 C In
C I 9 0 L y
S 7 .
FO AP 80 7.6 474 2= YT -Ra
. B Q 5 X
X 6
E Y N G X
L . NI R 0
B OI L E E 8 G
t
T K AI IA s ht ht T 5 E 5 0 C . ig
h
M D s g g E TI G 6 W V 6 8 K e
E C C R . e
n
n
e
n
e ZI F N - O E - - U N 7 Wl
S E O E kc L L S A K B E 1 1 D O 9.
S R L T M i f. t. L L E C 7 at
A E A O h e u R 5 L S S
8 o
B N
T R C F E S R T
M
S e
UI gr
D a
h
A C
R In
G
NI L
D AI
T N R
H R E E
W GI E B T
K O A D T A
RA BL RT EN O M
E S B H
M =
= = =
E S B Y
124
PIPE SUPPORT
SKETCH APPLICATION
(SO-0088110C : U1 TYPE)
SUPPORT
1 - NUT
(SO-0088120B : U2 TYPE)
SUPPORT
2 - NUTS
SUPPORT
(SO-0088130B – U3 TYPE)
2 - NUTS RUBBING PIECE
U-BOLT 1. PIPING IN FOT, LOT AND VOID SPACE IN ENGINE ROOM, AND
STERN TO BE CWT.
SUPPORT
126
SKETCH APPLICATION
BOLT &
NUT
SUPPORT
COPPER TUBE FOR COPPER PIPE OF DECK STEAM AND EXHAUST LINE
COPPER
PLATE
U-BOLT (STEEL) 50mm ~ 350mm PIPE DIA
BRASS PLATE
SMALL COPPER PIPE
(SO-0087230 B)
IN CASE OF 5~6 PIPES
BRASS PLATE
BRASS
SHEET
127
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 128/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
SKETCH APPLICATION
NEOPRENE
65 mm AND ABOVE
BOLT &
NUT
SUPPORT
(SO-0087320A : A2 TYPE)
BRASS PLATE
D D
0 D 0 D
. . . .
NI X IN X
A A
M M
M M
128
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 129/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
SKETCH APPLICATION
129
NOM. DIMENSION
ANGLE SHAPE APPLICATION
DIA. h B C
10 8 90
42 L40 x 5
(36) PIPE : 80Ø & BELOW
15 11 100
48 A : 500 & BELOW
(45)
25 17 120
58
(52) L40 x 5
40 25 130
62 (L50 x 6)
(58) PIPE : 80Ø & BELOW
50 30 140 A : 500 & BELOW
68 L50 x 6
(66)
65 38 170
76
(72)
80 45 82 180
(90) L65 x 8
100 57 230
101 (L75 x 9) PIPE : 100Ø & BELOW
(103) A : 500 & BELOW
125 70 260
115
(116)
150 83 280
127
(147)
200 108 360
L75 x 9
(173) (L75 x 9)
250 134 410
L90 x 10 IT CAN BE USED FOR ALL SIZE OF
(205) PIPE
300 160 490
L90 x 10
(223)
350 178 530
L100 x 10
(249)
400 203 580
(284)
450 229 680
(310)
500 254 730
L150 x 12
(335)
550 280 780
(370)
600 305 860
(395)
650 330 920
IT CAN BE USED FOR ALL CASES
(420)
700 356 970
(446)
750 380 1030
REMARKS
1. If there are more than 4 pipes on the common type band, the band to be increased by one step from the usual standard and in case of
more than 8 pipes the size to be increased by two steps from the usual standard.
2. Dimension with bracket in the b dimension column shows lower limit length.
130
NOMINAL PIPE DIA STEEL PIPE NOMINAL PIPE DIA NONFERROUS PIPE
15Ø AND UNDER ABOUT 1500 mm 4Ø – 10Ø ABOUT 600 – 1000 mm
80Ø – 200Ø ABOUT 3000 – 4000 mm 20Ø – 65Ø ABOUT 1500 – 2000 mm
80Ø – 200Ø ABOUT 2500 mm
250Ø AND OVER - 5500 mm 250Ø AND OVER ABOUT 2500 – 3000 mm
NOTE: As for larger pipe such as cargo pipe, interval of pipe support to be determined on the basic of
strength of pipe and pipe support in each case
h
Detail of bolt hole
U-bolt U-bolt
(Steel) (Steel)
15 500
50 650
65 700
80 750
125 850
150 900
250 1100
350
400
131
1. SCOPE: THIS STANDARD COVERS THE U-BOLT (WITH SINGLE NUT) FOR STEEL PIPE
R
G
S K
d
2
E
3. MATERIALS
MARK ITEM MATERIAL QUANTITY REMARKS
1 U-BOLT STEEL SS 1
132
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 133/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
1. SCOPE: THIS STANDARD COVERS THE U-BOLT (WITH DOUBLE NUT) FOR STEEL PIPE
R
G
d
2
E
K
800 32 812.8 M42 4.5 413 110 868 870 760 27.44
850 34 863.6 M42 4.5 438 110 918 920 810 28.84
900 36 914.4 M42 4.5 463 110 968 970 860 30.24
1000 40 1016.0 M42 4.5 515 110 1072 1070 960 33.07
1100 44 1117.6 M42 4.5 561 110 1164 1170 1060 35.94
133
1. SCOPE: THIS STANDARD COVERS THE U-BOLT (U3 TYPE) FOR STEEL PIPE
SPECIAL CASES.
R
3. MATERIALS
F
STEEL
2 NUT 4 JISB1181
SS41
T
1 U-BOLT STEEL 1
S MARK ITEM MAT'L QTY REMARKS
d
E 2
K
RUBBING PIECE (IN OTHER ARR'T)
t= 9 OR 12
∆
200 219.1 M20 2.5 112 65 242 ±1.0 261 1.92 265 1.95
250 273.0 M20 2.5 140 65 300 ±1.0 ∆ 316 2.24 321 2.28
300 323.8 M24 3 166 80 356 ±1.3 ∆ 372 3.81 376 3.86
350 355.6 M24 3 181 80 386 ±1.3 ∆ 403 4.15 407 4.20
400 406.4 M24 3 207 80 438 ±1.3 ∆ 454 4.62 458 4.63
450 457.2 M30 3.5 233 100 496 ±1.5 ∆ 510 8.30 516 8.16
500 508.0 M30 3.5 259 100 548 ±1.5 ∆ 564 9.02 570 9.15
550 558.8 M30 3.5 284 100 598 ±1.5 621 9.87
800 812.8 M42 4.5 413 130 868 ±1.5 888 27.82
+2.0
850 863.6 M42 4.5 438 130 918 939 29.24
-1.0
+2.0
900 914.4 M42 4.5 463 130 968 990 30.87
-1.0
+2.0
1000 1016.0 M42 4.5 515 130 1072 1092 33.54
-1.0
+2.0
1100 1117.6 M42 4.5 561 130 1164 1194 36.33
-1.0
134
1. SCOPE: THIS STANDARD COVERS THE U-BOLT (U4 TYPE) FOR HEATING PIPE IN TANK
3. MATERIAL
MARK ITEM MATERIAL QTY WT. (KG) REMARKS
135
1. SCOPE: THIS STANDARD COVERS PIPE BAND FOR COPPER PIPE NOMINAL SIZE 50 AND UNDER.
NOM. SIZE 6 ~ 50
B
t
3 1
4 R
d H
2
r
P
L
t
~
B
h
NOM. OUT l
R L P H B r t h d
DIA DIA
T=5
3. MATERIAL
MARK ITEM MATERIAL QTY WT. (KG) REMARKS
136
1
t1
t 2 TO BE ADHERED
BOLT AND
U - NUT 4 R
H 3
r 4/
60° R
D
t1
T
P
L
2-d
5C
3. MATERIAL
MARK ITEM MATERIAL QTY WT. (KG) REMARKS
3 1 -
137
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 138/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
b
SW11
c 0
a SW 11 3
M6 0
3
e
29 28
c GROUP 0
GROUP 0 GROUP 0
b SW11
d L L L b b
2 a
0 0
1 3 3
c
a
a a d
d d M6 b e
e d
GROUP GROUP
GROUP 1-5 1-5 1-5
138
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 139/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
0
3
38 0 c
3 m
48
9 .5
GROUP 0 28 4
1
d d
d GROUP 0 12 2
0 Ø11
3 0
3 h
m
0 0 h
3 3
e
d b b 3
e
f b
a
e GROUP
1-5
GROUP
1-5
WELDED PLATE
LONG WELD
EXTERNAL SCREW SAFETY
PLATE
GROUP UBE HEX-HEAD INTERNAL BUSH PLATE
BUILD UP SHORT
D HEX-HEAD
a d e f d e d e b d a b c m a h
6
8
10
12
0 - 48 38 - 61 - 298 28 -
R 1/8
¼
5/16
3/8
6
8
10
12
1 20 54 44 20 71 20 349 34 20
R 1/8
¼
5/16
3/8
14
15
16
18 427
2 26 60 50 26 86 26 2 40 26
R¼ 508
R 3/8
28 11
½
28 14 26 11
5/8 28 11 12 M6
30 30 26 26
20
22
23
516
3 25 33 68 58 33 104 33 2 48 33
723
R½
¾
1
28
4 30 40 77 67 40 120 40 297 57 40
R¾
32
35
38
40
5 42 52 90 80 52 145 52 370 70 52
R1
R1¼
1¼
1½
139
PAD
TYPE DIMENSION
WEIGHT
APPLICATION REMARKS
(kg)
MARK SKETCH A B R T
G2 80 38 19 6 0.14 50 x 6 F.B.
H2 90 50 25 9 0.31 50 x 9 F.B.
L1 65 65 15 6 0.13 40 x 40 x 5, 40 x 40 x 3L
L2 R 75 75 15 6 0.17 50 x 50 x 6, 50 x 50 x 4L
L3 95 95 20 9 0.42 65 x 65 x 8, 65 x 65 x 6L
C5
ØA 130 - - 9 0.94 80 STEEL PIPE
140
d=M6 NUT WEIGHT 0.0025 kg d=M8 NUT WEIGHT 0.0054 kg d=M10 NUT WEIGHT 0.012 kg
11.5 x 10 15 x 13 19.6 x 17
6 8 0
8 6. 1 5.
M 9. M 21 M 61
R R R
.5 .5 .8
2 5 G 0 2.5 6.5 G 0 3 8 G 0
l 4 l 5.5 l 7
44 55 0.045
49 60 0.048
d=M12 NUT WEIGHT 0.017 kg d=M14 NUT WEIGHT 0.025 kg d=M16 NUT WEIGHT 0.034 kg
2 4 6
1 8 1 1 1 3
M 1 M 2 M 2
R R R
.8 .8 .2
3.5 10 G 0 4 11 G 0 4 13 G 1
l 8 l 9 l 10
68 85 0.164
73 90 0.171
78 95 0.180
141
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 142/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
34.6 x 30 37 x 32 41.6 x 36
0 2 4
2 9 2 1 2 4
M 2 M 3 M 3
2R .2
R
6R
1. .
5 16 G 5 18 G 1 6 19 G 1
l 13 l 14 l 15
d=M27 NUT WEIGHT 0.16 kg d=M30 NUT WEIGHT 0.23 kg d=M33 NUT WEIGHT 0.289 kg
7 0 3
2 9 3 4 3 8
M 3 M 4 M 4
R R
.6 .6 2R
6 22 G 1 7 24 G 1 7 26 G
l 17 l 19 l 21
94 125 0.913
99 130 0.935
142
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 143/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
d = M36 NUT WEIGHT 0.395 kg d = M39 NUT WEIGHT 0.502 kg d= M42 NUT WEIGHT 0.653 kg
63.5 x 55 69.3 x 60 75 X 65
6 9 2
3 3 3 7 4 2
M 5 M 5 M 6
2R 2R 2R
8 29 G 8 31 G 9 34 G
l 23 l 25 l 26
143
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 144/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
d=M10 NUT WEIGHT 0.012 Kg d=M12 NUT WEIGHT 0.017 Kg d=M14 NUT WEIGHT 0.025 Kg
l 12 l 15 l 18
18 22 25
1.5 1.75 2
1.5 1.75 2
Ø Ø Ø
d d d
1.5 8 G 1.75 10 G 2 11 G
22.4 36 0.040
d=M16 NUT WEIGHT 0.034 Kg d=M20 NUT WEIGHT 0.064 Kg d=M22 NUT WEIGHT 0.079 Kg
l 20 l 25 l 25
28 32 36
2 2.5 2.5
2 2.5 2.5
Ø
Ø Ø d
d d
2.5 18 G
2 13 G 2.5 16 G
39 60 0.188
144
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 145/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
d=M24 NUT WEIGHT 0.11 Kg d=M27 NUT WEIGHT 0.16 Kg d=M30 NUT WEIGHT 0.23 Kg
l 27 l 30 l 33
40 42 45
3 3 3.5
3 3 3.5
Ø Ø Ø
d d d
3 19 G 3 22 G 3.5 24 G
d=M33 NUT WEIGHT 0.289 Kg d=M36 NUT WEIGHT 0.395 Kg d=M39 NUT WEIGHT 0.502 Kg
l 36 l 40 l 40
50 56 60
3.5 4 4
3.5 4 4
Ø Ø Ø
d d d
3.5 26 G 4 29 G 4 31 G
145
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 146/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
BELLMOUTH
FIG 1 TYPE A
Ød
0
0 ØD1
1
t
1
H
50
C
ØD2
Ø16
A-A
Unit : mm
OUTSIDE DIA
BODY REFERENCE
OF
NOMINAL SUCTION
APPLICABLE CALCULATED
SIZE AREA RATIO
PIPE D1 D2 H1 C t MASS
d (kg)
50 60.5 63 110 28 13 4.5 2.28 1.3
REMARKS: 1. In place of sleeve joint pipe, flange joint may be used, or the pipe may be welded directly to
the cone.
In such cases the dimensions of neck shall suitably be modified.
2. The legs made from round steel bar may be replaced with ribs made from steel plate.
146
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 147/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
FIG 2 TYPE B
N - Ød1
2
D
ØD3
ØD1
5
0
°
C
B 8
ØD 4
A-A
Unit : mm
BODY FLANGE REFERENCE
SUCTION
NOMINAL RIB CALCULATED
AREA
SIZE B
H D1 D4 C D3 D2 T N d RATIO MASS
(kg)
REMARKS: 1. The flange shall conform to JIS B 2210 nominal pressure 10K, but the pipe flange, nominal
pressure 5K, may be used if necessary.
2. The ribs shall be attached at the points which divide the circumference into three equal arcs.
147
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 148/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
FIG 3 TYPE C
a B
A A
Y
B-B B
Ød
0
0 ØD
1
t
l 1
H
Ø16 C
X
a-a A-A
Unit : mm
OUTSIDE DIA
BODY REFERENCE
OF SUCTION
NOMINAL LEG
APPLICABLE AREA CALCULATED
SIZE I
PIPE D H1 X Y C t RATIO MASS
d (kg)
200 216.3 220 340 750 450 25 10 50 1.70 45.0
450 457.2 462 360 900 600 100 12 200 1.65 84.6
500 508.0 512 450 1100 600 100 12 200 1.54 114.1
550 558.8 563 440 1100 700 120 12 240 1.58 120.1
600 609.0 614 540 1300 700 130 12 260 1.62 158.0
REMARKS: 1. In place of sleeve joint, pipe flange may be used, or the pipe may be welded directly to the
cone. In such cases, the dimensions of neck shall suitably be modified.
2. The legs made from round steel bar may be replaced with ribs made from steel plate.
3. The bellmouths of nominal sizes 250S and 300S are for stripping purpose
4. Material of bell mouth : Steel plate
148
STPG 38 SCH 80
USED PIPE: NOMINAL DIA 40 OUT DIA THICKNESS
48.6 5.1
PIPE LENGTH / ONE ROLL 1193.2 MM
0
HEATING AREA / 1M 0.1528 M²
0
1
0
0
1
0
0
1
0
0
1
2. MATERIAL USED
0 0
0 0
5 1
0 WEIGHT
0
1 MARK ITEM MATERIAL QTY REMARK
0 PER
0 TOTAL
1 ONE
STEEL
0
0
HEATING
0 1 PIPE 1 30.1
1 5 COIL
STPG 38
60 STEEL
2 SOCKET PIPE 2 0.437 0.774
25 350 STPG 38
50
12
5 R 2 25
R 5
12
0 .5
2 R
12 5
3 6 6.5
5
5 R
12
MAX.
)8
Ø Ø 1.6 Ø 3
1. 5. 6.
3 0 8 G
6 5 4 P
T
S(
25 350
1.
5
149
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 150/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
E2 E2
E1 E2
150
D D
D D
D D
D D D D D D D D D D A D A D A D A
50 65 80 100 135 160 160 160 170 160 35 180 45 180 45 190 45
65 80 96 125 160 180 180 185 195 180 40 200 50 200 50 205 50
80 95 115 130 185 190 205 195 215 205 45 230 45 230 55 230 50
100 120 145 145 160 210 220 235 240 265 230 40 240 45 255 55 260 55
125 145 170 170 180 245 260 280 265 290 260 45 285 55 300 65 285 55
150 170 200 200 230 275 290 315 290 330 300 50 320 55 330 70 320 55
200 220 255 255 285 330 340 360 355 390 350 50 380 55 380 65 380 60
250 270 305 305 320 395 410 440 420 455 410 60 450 65 460 80 450 65
300 320 355 355 380 440 455 490 495 530 460 55 500 60 510 80 510 80
350 360 390 395 400 490 500 550 545 595 540 60 520 65 570 90 560 85
400 410 440 445 450 550 570 615 610 660 570 65 600 75 630 95 620 90
450 460 490 495 500 615 640 685 645 630 70 650 80 700 110 660 90
500 510 545 545 560 665 685 740 710 680 70 700 80 760 110 730 95
550 565 595 600 600 730 755 805 760 750 80 770 90 820 115
600 615 650 660 660 780 805 855 825 800 80 820 90 870 115 840 100
950 1250
151
1. APPLICATION:
This standard is to ensure the necessary working space available and also to decide the limitation dimension
inside the engine room for the normal commercial vessel such as piping arrangement, installation of out fitting,
welding and hull reinforcement work.
MIN. 25mm
l MIN. 25mm
MIN. 100mm
Using JIS 5K and 10K (ANSI 150 LB) flanges and without l dimension refer to TABLE –1.
l
MIN. 25mm
152
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 153/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
2) In way of high pressure pipe flanges, sufficient room to be provided for the flanges area as
shown on the figure below for retightening or renewal of packing in case of leakage. Standard
dimension is 500MM but not to be less than 300mm.
(Applicable for flange part with 600 LB above)
0
50 IN.
(M m)
0m
30
.
m
0 IN m
5 M 0
0
3
FLAT FLAT
50 300
0 0
0
IN CASE OF
5 3
50 50
(IN CASE OF GROUND STAGE, DO NOT
INSTALL PIPE NEAR TO THE PILLAR)
153
BHD STIFFENER
50 50
50 50
MIN.
50
50 50
50
50
50
50
100 100
100
SIDE WEB
SHELL 100
10
0
SIDE
SHELL
SIDE
SHELL
6) Penetration fitting
BHD BUTT
OR
30 100 D SEAM
SIDE
SHELL
D > 50mm
=
SIDE
SHELL
300
300
300
154
WALL
A 0
5
K
UN
TR
50
PIPE
SECTION
SIDE VIEW
CABLE CABLE
. .
IN 0
0 IN 0
0
M 2 M 4
INSULATION O.D.
INSULATION O.D.
Welding work required space in way of confine space to be refer to SOT IS-SOT-A327003 minimum
dimension for welding work in way of confine space.
155
MIN. MIN.
50 50
MIN.
50
100
5
2 FRAME OR BULKHEAD
.
IN
M
NOTE:
2) IN CASE OF OBSTRUCTION BY
OUTFITTING, SAME METHOD TO
BE FOLLOWED.
PENETRATION FITTING
MIN. 250
156
G G
T IN T IN
IT IT
TF TF
OU O U
100 100
G
TIN
T
TFI
OU
150
157
158
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 159/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
The minimum space required for the hull reinforcement work to be ensured during the design stage with the
following dimension.
0
0
8
MINIMUM WORKING
SPACE
0
60
600
159
TABLE –1
NOM.
10 15 20 25 40 50 65 80 100 125 150 200 225 250 300
DIA.
10 48
54
49 51
15 57 59
56
52 54 57
20 59 61 64
61 64
57 59 62 65
25 72 74 77 80
66 69 72 TOP : 5K
69 71 74 77 85 MID. : 10K
40 79 81 84 87 95
75 78 71 89 BTM. :150PSI
50 74
87 76
89 79
92 82
95 90
102 96
108
88 91 94 102 108
87 89 92 95 102 108 116
65 97 99 102 105 112 118 126
100 103 106 114 120 128
99 101 104 107 115 121 129 135
80 102 104 107 110 117 123 131 137
107 110 113 121 127 135 141
109 111 114 117 125 131 139 145 158
100 114 116 119 122 130 136 144 150 163
126 129 132 140 146 154 160 173
127 129 132 135 142 148 156 163 175 188
125 134 136 139 142 150 156 164 170 183 195
138 141 144 152 158 166 172 185 197
150 142
149 144
151 147
154 150
157 157
165 163
171 171
179 178
185 190
198 203
210 216
223
151 154 157 165 171 179 185 198 210 223
169 171 174 177 185 191 199 205 218 230 243 269
200 174 176 179 182 190 196 204 210 223 235 246 275
183 186 189 197 203 211 217 230 242 255 281
182 184 187 190 197 203 211 218 230 243 256 281 294
225 184 186 189 192 200 206 214 220 233 245 258 285 296
202 204 207 210 217 223 231 238 250 263 276 301 314 327
250 209 211 214 217 225 231 239 245 258 270 283 310 321 334
215 218 221 229 235 243 249 262 274 287 313 338
224 226 229 232 240 246 254 260 273 285 293 325 336 349 375
300 232 234 237 240 247 253 261 268 280 293 306 331 344 357 382
253 256 259 267 273 281 288 300 312 325 351 376 402
160
TABLE –2
NOM.
10 15 20 25 32 40 50 65 80 90 100 125 150 200 250 300
DIA.
300 319
161
0.914 1.829
1.2 9.42 15.8 — — VENTILATION TRUNKING
( 3’ ) ( 6’ )
1.524 6.096
SS41 4.5 35.32 328 — — TANK
( 5’ ) ( 20’ )
162
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 163/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
1.524 6.096
7 54.95 511 — STEEL DOOR
( 5’ ) ( 20’ )
583
8 62.80 TANK, FUNNEL
1.884
656
9 70.65 TANK, FUNNEL
2.120
729
10 78.50 TANK, FUNNEL
2.355
875
12 94.20 TANK
2.826
1.021
14 109.9 — TANK, EYE PLATE
3.297
1.167
16 125.6 — EYE PLATE
1.524 x 6.096 3.768
( 5’) x ( 20’)
2.500 x 12.00 1.386
19 149.2 — EYE PLATE, EQ. SEAT
4.475
NOTE: 1) Plate thickness more than 32 mm are not regularly use and excluded from this standard.
2) Figure shown in ( ) are mainly use for blind flange.
3) This standard base on < IS >: SOT-001000A
163
∆ 8 62.80 583 —
∆ 9 70.65 656 —
NOTE: 1) Plate thickness more than 32 mm are not regularly use and excluded from this standard.
2) This standard base on < IS >: SOT-001000A
1.219 2.438
3.2 26.83 79.7 FLOOR GRATING AND STEP
( 4’ ) ( 8’ )
1.219 2.438
4.5 37.04 110 FLOOR GRATING AND STEP
( 4’ ) ( 8’ )
1.524 3.048
∆ 4.5 37.04 172 FLOOR GRATING AND STEP
( 5’ ) ( 10’ )
1.524 3.048
6 48.81 227 FLOOR GRATING AND STEP
( 5’ ) ( 10’ )
NOTE: Base on kawasaki steel data
164
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 165/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
GALVANIZE PLATE
DIMENSION UNIT WT WEIGHT
FITTING CODE USAGE
THICKNESS WIDTH LENGTH (kg/m²) (kg)
1.219 x 2.438
2.3 18.44 54.80 VENTILATION TRUNKING
( 4’) x ( 8’ )
0.914 x 1.829
0.5 4.17 6.97 — FOR DUCTING USED
( 3’ ) x ( 6’ )
1.219 x 2.438
2.3 ( 4’) x ( 8’ ) 18.44 54.80 VENTILATION TRUNKING
165
R2
H R1
R2
166
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 167/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
2
t
t1 H
B
H-BEAM : SS41
DIMENSION UNIT WT FITTING CODE
∆ 150 75 5 7 14.0 Ο
∆
350 175 7 11 49.6
∆ 340 250 9 14 79.7
∆ 400 200 8 13 66
167
t2
(B-t1)/2
t1
H
H/2
t2
t1 H
B
I-BEAM : SS41
DIMENSION UNIT WT FITTING CODE
LENGTH USAGE
H B t1 t2 (kg/²) SS41 SS
168
∆ 65 12 6.12 33.7 Ο Ο
∆ 75 12 7.06 38.8 Ο Ο
∆ 90 6 4.24 23.3 Ο Ο
∆ 90 12 8.48 46.6 Ο Ο
169
9 0.499 2.74
Ο FOR SMALL RING, HOOK
170
IL
P
125 x 50 x 20 x 3.2 6.13 Ο INCLINE LADDER
171
55 18.7 103
60 22.2 122
∆ 65 26.0 143
70 30.2 166
∆ 75 34.7 191
80 39.5 217
∆ 85 44.5 245
S 25 C 90 49.9 274
∆ 95 55.5 306
172
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 173/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
METRIC (I.S.O.)
NOMINAL NOMINAL NOMINAL
DIA OF DIA OF PITCH (P) TAPPING DIA OF PITCH (P) TAPPING
THREADS PITCH (P) TAPPING THREADS MM DRILL DIA MM THREADS MM DRILL DIA MM
MM MM DRILL DIA MM MM MM
M 2.0 0.25 1.75 M 11.0 1.00 10.00 M 25.0 1.50 23.50
M 2.0 0.40 1.60 M 11.0 1.50 9.50 M 25.0 2.00 23.00
M 2.2 0.25 1.95 M 12.0 1.00 11.00 M 27.0 1.50 25.50
M 2.2 0.45 1.75 M 12.0 1.25 10.80 M 27.0 3.00 24.00
M 2.5 0.35 2.15 M 12.0 1.50 10.50 M 28.0 1.50 26.50
M 2.5 0.45 2.05 M 12.0 1.75 10.20 M 30.0 1.50 28.50
M 3.0 0.35 2.65 M 14.0 1.00 13.00 M 30.0 3.50 26.50
M 3.0 0.50 2.50 M 14.0 1.25 12.80 M 32.0 1.50 30.50
M 3.5 0.35 3.15 M 14.0 1.50 12.50 M 33.0 2.00 31.00
M 3.5 0.60 2.90 M 14.0 2.00 12.00 M 33.0 3.50 29.50
M 4.0 0.50 3.50 M 16.0 1.00 15.00 M 36.0 3.00 33.00
M 4.0 0.70 3.30 M 16.0 1.50 14.50 M 36.0 4.00 32.00
M 4.5 0.50 4.00 M 16.0 2.00 14.00 M 39.0 3.00 36.00
173
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 174/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
NOMINAL DIA OF PITCH (P) TAPPING DRILL DIA NOMINAL DIA OF PITCH (P) TAPPING DRILL DIA
T.P.I T.P.I
THREADS mm MM THREADS mm MM
1/8” 0.907 28 8.60 1/8” 0.0250 40 2.55
¼” 1.337 19 11.50 3/16” 0.0417 24 3.70
3/8” 1.337 19 15.00 ¼” 0.0500 20 5.10
½” 1.814 14 18.75 5/16” 0.0556 18 6.50
¾” 1.814 14 24.25 3/8” 0.0625 16 7.90
1” 2.309 11 30.40 7/16” 0.0714 14 9.30
1 ¼” 2.309 11 39.00 ½” 0.0833 12 10.50
1 ½” 2.309 11 45.00 9/16” 0.0833 12 12.10
2” 2.309 11 56.75 5/8” 0.0909 11 13.50
11/16” 0.0909 11 15.00
¾” 0.1000 10 16.25
BRITISH STANDARD 7/8” 0.1111 9 19.25
PIPE FASTENING (B.S.P.F) G 1” 0.1250 8 22.00
NOMINAL DIA OF PITCH (P) TAPPING DRILL DIA 1 1/8” 0.1429 7 24.75
T.P.I
THREADS mm MM 1 ¼” 0.1429 7 28.00
1/8” 0.907 28 8.80 1 ½” 0.1667 6 33.50
¼” 1.337 19 11.80 1 ¾” 0.2000 5 39.00
3/8” 1.337 19 15.25 2” 0.2222 4.5 44.50
½” 1.814 14 19.00
5/8” 1.814 14 21.00
BRITISH STANDARD FINE (B.S.F)
¾” 1.814 14 24.50
7/8” 1.814 14 28.25 NOMINAL DIA OF PITCH (P) TAPPING DRILL DIA
T.P.I
1” 2.309 11 30.75 THREADS mm MM
1 ¼” 2.309 11 39.50 3/16” 0.0312 32 4.00
1 ½” 2.309 11 45.00 7/32” 0.0357 28 4.60
1 ¾” 2.309 11 51.00 ¼” 0.0385 26 5.30
2” 2.309 11 57.00 9/32” 0.0385 26 6.10
5/16” 0.0455 22 6.80
3/8” 0.0500 20 8.30
7/16” 0.0556 18 9.70
½” 0.0625 16 11.10
9/16” 0.0625 16 12.70
5/8” 0.0714 14 14.00
11/16” 0.0714 14 15.50
¾” 0.0833 12 16.75
7/8” 0.0909 11 19.75
1” 0.1000 10 22.75
1 1/8” 0.1111 9 25.50
1 ¼” 0.1111 9 28.50
1 3/8” 0.1250 8 31.50
1 ½” 0.1250 8 34.50
174
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 175/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
175
http://slide pdf.c om/re a de r/full/jis-piping-ha ndbook 176/177
5/21/2018 JIS Piping Ha ndbook - slide pdf.c om
U.S
U.S STEEL WIRE(old)
STANDARD : STEEL WIRE EXCEPT
: STAINLESS STEEL MUSIC WIRE:
SHEETS,
SWG: ENGLISH LEGAL STANDARD WIRE GAUGE ;
MANUFACTURERS’ STANDARD: UNCOATED STEEL SHEETS.