Professional Documents
Culture Documents
SMAJ_ENG_DS
SMAJ_ENG_DS
SMAJ Series
Description
The SMAJ series is designed specifically to protect
sensitive electronic equipment from voltage transients
induced by lightning and other transient voltage events.
Features
t)BMPHFO'SFF t'BTUSFTQPOTFUJNF
t3P)4DPNQMJBOU typically less than 1.0ps
t'PSTVSGBDFNPVOUFE from 0 Volts to VBR min
applications to optimize t5ZQJDBM*R less than 1μA
board space above 12V
Agency Approvals t-PXQSPmMFQBDLBHF t)JHIUFNQFSBUVSF
t#VJMUJOTUSBJOSFMJFG soldering: 260°C/40
AGENCY AGENCY FILE NUMBER seconds at terminals
t(MBTTQBTTJWBUFEKVODUJPO
t5ZQJDBMNBYJNVN
E230531 t-PXJOEVDUBODF
temperature coefficient
t&YDFMMFOUDMBNQJOH ΔVBR = 0.1% x VBR@25°C x ΔT
capability
t1MBTUJDQBDLBHFIBT
Maximum Ratings and Thermal Characteristics t81FBL1VMTFQPXFS Underwriters Laboratory
(TA=25OC unless otherwise noted) capability at 10 x 1000μs Flammability 94V-O
waveform, repetition rate
t.BUUF5JO-FBEoGSFF
Parameter Symbol Value Unit (duty cycle): 0.01%
Plated
Peak Pulse Power Dissipation at
TA=25ºC by 10x1000μs waveform PPPM 400 W
(Fig.1)(Note 1), (Note 2)
Power Dissipation on infinite heat Applications
PM(AV) 3.3 W
sink at TA=50OC
Peak Forward Surge Current, 8.3ms TVS devices are ideal for the protection of I/O Interfaces,
IFSM 40 A VCC bus and other vulnerable circuits used in Telecom,
Single Half Sine Wave (Note 3)
Maximum Instantaneous Forward Computer, Industrial and Consumer electronic applications.
Voltage at 25A for Unidirectional VF 3.5V/6.5 V
only (Note 4)
Operating Junction and Storage
TJ , TSTG -65 to 150 °C
Temperature Range
Typical Thermal Resistance Junction
RuJL 30 °C/W
to Lead
Typical Thermal Resistance Junction
RuJA 120 °C/W
to Ambient
Notes:
1. Non-repetitive current pulse, per Fig.3 and derated above TA=25ºC per Fig. 2.
2. Mounted on 5.0x5.0mm copper pad to each terminal.
3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional
device only.
4. VF < 3.5V for VBR <
_ 200V and VF< 6.5V for VBR >
_ 201V.
Electrical Characteristics
For parts without A (VBR is ± 10% and VC is 5% higher than with A parts).
Figure 1 - Peak Pulse Power Rating Curve Figure 2 - Pulse Derating Curve
SMAJ Series
10 100
80
Derating in Percentage %
60
1
40
20
0.2x0.2" (5.0x5.0mm)
Copper Pad Area
0.1 0
0.000001 0.00001 0.0001 0.001 0 25 50 75 100 125 150 175
td-Pulse Width (sec.) TA-Ambient temperature (ºC)
150
tr=10μsec TJ=25°C
10000
IPPM- Peak Pulse Current, % IRSM
( )
IPPM IPPM
2
100
Figure 5 - Steady State Power Dissipation Derating Figure 6 - Maximum Non-Repetitive Forward Surge
Curve Current Uni-Directional Only
45
1.2
PM(AV), Steady State Power Dissipation (W)
40
1
35
0.8 30
25
(A)
0.6
20
0.4 15
10
0.2
5
0 0
1 10 100
0 25 50 75 100 125 150 175
TA - Ambient Temperature (ºC) Number of Cycles at 60 Hz
Soldering Parameters
Temperature (T)
- Time (min to max) (ts) oTFDT Ts(max)
Polarity Color band denotes cathode except Bipolar High Temp. Storage JESD22-A103
Dimensions
DO-214AC (SMA)
Inches Millimeters
Cathode Band
Dimensions
Min Max Min Max
A 0.049 0.065 1.250 1.650
A C
B 0.157 0.177 3.990 4.500
C 0.100 0.110 2.540 2.790
B D 0.078 0.090 1.980 2.290
SMAJ Series
XXX
5% VOLTAGE TOLERANCE
BI-DIRECTIONAL
F
VOLTAGE
SERIES
Littelfuse Logo
Marking Code
Packaging