Professional Documents
Culture Documents
sikaflex-255-fc (fincapé nelo)
sikaflex-255-fc (fincapé nelo)
Sikaflex®-255 FC
Fast curing direct glazing adhesive for commercial vehicles
1/2
CURE MECHANISM Consider the viscosity increase at low temper- BASIS OF PRODUCT DATA
Sikaflex®-255 FC cures by reaction with atmo- ature. For easy application, condition the ad- All technical data stated in this document are
spheric moisture. At low temperatures the wa- hesive at ambient temperature prior to use. To based on laboratory tests. Actual measured
ter content of the air is generally lower and the ensure a uniform thickness of the bondline it is data may vary due to circumstances beyond
curing reaction proceeds somewhat slower (see recommend to apply the adhesive in form of a our control.
diagram 1). triangular bead (see figure 1).
ENVIRONMENTAL, HEALTH AND
SAFETY
For further information and advice regarding
transportation, handling, storage and disposal
of chemical products, user should refer to the
actual Safety Data Sheets containing physical,
environmental, toxicological and other safety
related data. User must read the current actual
Figure 1: Recommended bead configuration Safety Data Sheets before using any products.
In case of an emergency, call CHEMTREC at 1-
Sikaflex®-255 FC can be processed with manu- 800-424-9300, International 703-527-3887.
al, pneumatic or electric driven piston guns as
well as pump equipment. The open time is sig- LEGAL DISCLAIMER
nificantly shorter in hot and humid climate. The Prior to each use of any product of Sika Corpor-
glass must always be installed within the open ation, its subsidiaries or affiliates (“SIKA”), the
Diagram 1: Curing speed Sikaflex®-255 FC
time. Never install a glass after the adhesive user must always read and follow the warnings
has built a skin. and instructions on the product’s most current
CHEMICAL RESISTANCE product label, Product Data Sheet and Safety
Sikaflex®-255 FC is generally resistant to fresh For advice on selecting and setting up a suit-
able pump system, contact the System Engin- Data Sheet which are available at usa.sika.com
water, seawater, diluted acids and diluted
eering Department of Sika Industry. or by contacting SIKA’s Technical Service De-
caustic solutions; temporarily resistant to fuels,
partment via email at tsmh@us.sika.com.
mineral oils, vegetable and animal fats and oils;
Removal Nothing contained in any SIKA literature or ma-
not resistant to organic acids, glycolic alcohol,
concentrated mineral acids and caustic solu- Uncured Sikaflex®-255 FC can be removed from terials relieves the user of the obligation to
tions or solvents. tools and equipment with Sika® Remover-208 read and follow the warnings and instructions
or another suitable solvent. Once cured, the for each SIKA product as set forth in the current
METHOD OF APPLICATION material can only be removed mechanically. product label, Product Data Sheet and Safety
Surface Preparation Hands and exposed skin have to be washed im- Data Sheet prior to use of the SIKA product.
Surfaces must be clean, dry and free from mediately using a suitable industrial hand SIKA warrants this product for one year from
cleaner and water. date of installation to be free from manufactur-
grease, oil, dust and contaminants.
Do not use solvents on skin. ing defects and to meet the technical proper-
Surface treatment depends on the specific
ties on the current Product Data Sheet if used
nature of the substrates and is crucial for a long FURTHER INFORMATION as directed within the product’s shelf life. User
lasting bond. Suggestions for surface prepara- The information herein is offered for general determines suitability of product for intended
tion may be found on the current edition of the guidance only. Advice on specific applications is use and assumes all risks. User’s and/or buyer’s
appropriate Sika® Pre-treatment Chart. Con- available on request from the Technical Depart- sole remedy shall be limited to the purchase
sider that these suggestions are based on ex- ment of Sika Industry. price or replacement of this product exclusive
perience and have in any case to be verified by Copies of the following publications are avail- of any labor costs. NO OTHER WARRANTIES EX-
tests on original substrates. able on request: PRESS OR IMPLIED SHALL APPLY INCLUDING
▪ Safety Data Sheets ANY WARRANTY OF MERCHANTABILITY OR FIT-
Application
▪ Sika Pre-treatment Chart NESS FOR A PARTICULAR PURPOSE. SIKA SHALL
Sikaflex®-255 FC can be processed at temperat-
For 1-component Polyurethanes NOT BE LIABLE UNDER ANY LEGAL THEORY FOR
ures (climate and product) between 10 °C and ▪ General Guidelines
35 °C (50 °F and 95 °F) but changes in reactivity SPECIAL OR CONSEQUENTIAL DAMAGES. SIKA
Bonding and Sealing with 1-component SHALL NOT BE RESPONSIBLE FOR THE USE OF
and application properties have to be con- Sikaflex®
sidered. The optimum temperature for sub- THIS PRODUCT IN A MANNER TO INFRINGE ON
strate and sealant is between 15 °C and 25 °C PACKAGING INFORMATION ANY PATENT OR ANY OTHER INTELLECTUAL
(59 °F and 77 °F). PROPERTY RIGHTS HELD BY OTHERS. Sale of
Cartridge 300 ml SIKA products are subject to the Terms and
Conditions of Sale which are available at ht-
Unipack 600 ml
tps://usa.sika.com/en/group/SikaCorp/term-
Drum 200 l sandconditions.html or by calling +1 800-933-
7452.
2/2