Professional Documents
Culture Documents
OUTPUT CP Rev final
OUTPUT CP Rev final
PAGE NO. 1
****************************************************
* *
* STAAD.Pro CONNECT Edition *
* Version 22.00.00.15 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= MAY 30, 2024 *
* Time= 13:21:23 *
* *
* Licensed to: only @::LAVteam::® *
****************************************************
1. STAAD SPACE
INPUT FILE: D:\Salahuddin\komban\Tanajib refinary\Tanajib Refinery Car Parking Shed 6x6 Final.STD
2. START JOB INFORMATION
3. ENGINEER DATE 27-MAY-24
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. 1 0 0 0; 4 6 3.4 0; 7 0 0 6; 8 6 3.4 6; 20 0 3.1 0; 21 0 3.1 6; 24 1.5 3.175 0
9. 25 3 3.25 0; 26 4.5 3.325 0; 27 1.5 3.175 6; 28 3 3.25 6; 29 4.5 3.325 6
10. 30 0 3.25 0; 31 0 3.25 6; 32 0 2.9 0; 33 0 2.9 6
11. MEMBER INCIDENCES
12. 1 1 32; 8 7 33; 13 4 8; 23 20 30; 24 21 31; 25 21 27; 26 20 24; 27 20 21
13. 28 24 25; 29 25 26; 30 26 4; 31 27 28; 32 28 29; 33 29 8; 34 24 27; 35 25 28
14. 36 26 29; 37 32 20; 38 33 21; 39 33 28; 40 32 25; 41 32 33
15. DEFINE MATERIAL START
16. ISOTROPIC STEEL
17. E 2.05E+08
18. POISSON 0.3
19. DENSITY 76.8195
20. ALPHA 1.2E-05
21. DAMP 0.03
22. TYPE STEEL
23. STRENGTH RY 1.5 RT 1.2
24. END DEFINE MATERIAL
25. MEMBER PROPERTY AMERICAN
26. 1 8 23 24 37 38 TABLE ST W8X40
27. 25 26 28 TO 33 39 40 TABLE ST W8X24
28. MEMBER PROPERTY AMERICAN
29. 41 TABLE ST W8X18
30. MEMBER PROPERTY BRITISH
31. 13 27 34 TO 36 TABLE ST CH152X76
32. CONSTANTS
33. MATERIAL STEEL ALL
34. SUPPORTS
35. 1 7 FIXED
36. DEFINE WIND LOAD
*** NOTE: If any floor diaphragm is present in the model Wind Load definition
should be defined after Floor Diaphragm definition. Otherwise wind
load generation may be unsuccessful during analysis.
P R O B L E M S T A T I S T I C S
-----------------------------------
100. PARAMETER 1
101. CODE AISC UNIFIED 2016
102. MAIN 1 MEMB 13 27 34 TO 36
103. FYLD 250000 ALL
104. CAN 1 MEMB 25 26 28 TO 33
105. STEEL MEMBER TAKE OFF ALL
STEEL TAKE-OFF
--------------
The capacity results and intermediate results in the report follow the notations
and axes labels as defined in the AISC 360-16 code.
The analysis results are reported in STAAD.Pro axis convention and the AISC 360:16
design results are reported in AISC 360-16 code axis convention.
1. Section classification reported is for the cross section and loadcase that
produced the worst case design ratio for flexure/compression Capacity results.
2. Results for any Capacity/Check that is not relevant for a section/loadcase
based on the code clause in AISC 360-16 will not be shown in the report.
3. Bending results are reported as being “about” the relevant axis (X/Y), while
the results for shear are reported as being for shear forces “along” the axis.
E.g : Mx indicates bending about the X axis, while Vx indicates shear along
the X axis.
************************************************************
* For technical assistance on STAAD.Pro, please visit *
* http://www.bentley.com/en/support/ *
* *
* Details about additional assistance from *
* Bentley and Partners can be found at program menu *
* Help->Technical Support *
* *
* Copyright (c) 1997-2017 Bentley Systems, Inc. *
* http://www.bentley.com *
************************************************************