Professional Documents
Culture Documents
HARSHVARDHAN IT
HARSHVARDHAN IT
IT PROJECT-1
ON
Computer Network
This is to certify that Harshvardhan Singh has carried out the work
Network under my supervision and guidance. No part of this project has been
submitted for any other degree or diploma. The work included in this thesis is
The candidate has worked regularly and fulfilled all requirements as per the
I declare that the Computer Network has been written by me under the
guidance of Dr. Megha Vimal H.O.D of MBA Department No part of this thesis has
previously formed the basis for the award of any degree or fellowship.
Harshvardhan Singh
Acknowledgement
Secondly I would also like to thank my parents and friends who helped
INTRODUCTION
Networking
Networking is a practice of linking of two or more computing devices such as PCs,
printers, faxes etc., with each other Connection between two devices is through
physical media or logical media to share information, data and resources. Networks are
made with the hardware and software.
Cable/media
Fig1.1: Computer netwo rk
There are many different ways to connect your computer to another computer or a
network. Using Windows 2000, you can connect your computer to:
Types of Networking:
Page 1 of 45
Wired network
Wireless network
Wired networks:
Wired networks are almost always faster and less expensive than wireless networks.
Once connected, there is little that can disrupt a good-wired connection. Wired networks
come in many forms, but the most popular are HomePNA and Ethernet. HomePNA uses
the existing phone line wires in your home and Ethernet needs special network cabling.
Wireless Networks:
Mobile computers, such as notebook computers and personal digital assistants (PDAs)
are the fastest- growing segment of the computer industry. Many of the owner of these
computers have desktop machines on LANs and WANs back at the office and want to be
connected to their home base even when away from home or en route. Since having a
wired connection is impossible in cars and airplanes, there is a lot of interest in wireless
networks.
Page 2 of 45
Fig1.3: Wireless network
Models of Networking
Model means the connectivity of two computers. We have many types of networking
models.
(i) Client – Server Model
(ii) Peer to Peer Model (Workgroup Model)
(iii) Domain Model
Categories of Network
Local Area Network
(LAN)
LAN is a computer network that is used to connect computers and work station to share
data and resources such as printers or faxes. LAN is restricted to a small area such as
home, office or college. Devices used in LAN are: HUB and switch. Media for LAN is
UTP cables.
Networking components:
When a computer or device A is requesting a resource from another computer or device
B, the item A is referred to as a client. Because all or most items that are part of a network
live in association or cooperation, almost any one of them can be referred to as a client.
Based on this, there can be different types of clients. The most regularly used of them is
referred to as a workstation.
If you already have one or more computers that you plan to use as workstations, you can
start by checking the hardware parts installed in the computer. The computer must meet
the following requirements:
Processor:
An Intel Pentium or Celeron family of processors or an AMD K6/Athlon/Duron family
of processors. The processor should have a 300 megahertz clock speed. A higher speed is
recommended.
RAM:
The computer must have a memory of at least 64 megabytes (MB). As memory is not
particularly expensive nowadays, you should upgrade the computer's memory to at least
512MB.
Hard Drive:
Before installing Microsoft Windows XP Professional on an existing computer, make
sure the hard drive has the appropriate capacity to handle the OS. To find out how much
space your hard drive has, you can open Windows Explorer or My Computer, right-click
the C:\ drive and click Properties.
Network Cables:
Cable is used to connect computers. Although we are planning to use as much wireless as
possible, you should always have one or more cables around. In our network, we will use
Category 5 cable RJ-45. The ends of the cable appear as follows:
Routers:
Routers are networking devices that forward data packets between networks using
headers and forwarding tables to determine the best path to forward the packets. Routers
work at the network layer of the TCP/IP model or layer 3 of the OSI model. Routers also
provide interconnectivity between like and unlike media. Here is an example of a router:
Network Cards:
In order to connect to a network, a computer must be equipped with a device called a
network card. A network card, or a network adapter, also called a network interface card,
or NIC, allows a computer to connect to the exterior. If you buy a computer from one of
those popular stores or big companies on the Internet, most of their computers have a
network card tested and already. You can reliably use it. If you go to a store that sells or
manufactures computers, you can ask them to install or make sure that the computer has a
network card. When it comes to their installation, there are roughly two categories of
network cards: internal and external. An internal network card looks like a printed circuit
board with some objects "attached" or "glued" to it and it appears as follows:
Switch:
A network switch or switching hub is a computer networking device that
connects network segments. A network switch is a small hardware device that joins
multiple computers together within one local area network (LAN). Technically, network
switches operate at layer two (Data Link Layer) of the OSI model.
Network switches appear nearly identical to network hubs, but a switch generally
contains more intelligence (and a slightly higher price tag) than a hub. Unlike hubs,
network switches are capable of inspecting data packets as they are received, determining
the source and destination device of each packet, and forwarding them appropriately. By
delivering messages only to the connected device intended, a network switch conserves
network bandwidth and offers generally better performance than a hub.
Server:
A network server is a computer designed to process requests and deliver data to other
(client) computers over a local network or the Internet. Examples include Web servers,
proxy servers, and FTP servers. Not only should you learn about servers on the Internet,
private network servers for business and personal use are also becoming more common.
Figure 2.6: Server
Access Point:
In computer networking, a wireless access point (WAP) is a device that allows wireless
devices to connect to a wired network using Wi-Fi, Bluetooth or related standards. The
WAP usually connects to a router (via a wired network), and can relay data between the
wireless devices (such as computers or printers) and wired devices on the network.
IP Addressing:
PROJECT TECHNIQUES
An IP (Internet Protocol) address is a unique identifier for a node or host connection on
an IP network. An IP address is a 32 bit binary number usually represented as 4 decimal
values, each representing 8 bits, in the range 0 to 255 (known as octets) separated by
decimal points. This is known as "dotted decimal" notation. Example: 140.179.220.200 It
is sometimes useful to view the values in their binary form. 140 .179 .220 .200
10001100.10110011.11011100.11001000 Every IP address consists of two parts, one
identifying the network and one identifying the node. The Class of the address and the
subnet mask determine which part belongs to the network address and which part belongs
to the node address. The four numbers in an IP address are called octets, because they
each have eight positions when viewed in binary form. If you add all the positions
together, you get 32, which is why IP addresses are considered 32-bit numbers. Since
each of the eight positions can have two different states (1 or 0) the total number of
possible combinations per octet is 28 or 256. So each octet can contain any value between
0 and 255. Combine the four octets and you get 232 or a possible 4,294,967,296 unique
values. Out of the almost 4.3 billion possible combinations, certain values are restricted
from use as typical IP addresses. For example, the IP address 0.0.0.0 is reserved for the
default network and the address 255.255.255.255 is used for broadcasts. Understanding
IP Addresses
An IP address is an address used in order to uniquely identify a device on an IP network.
The address is made up of 32 binary bits, which can be divisible into a network portion
and host portion with the help of a subnet mask. The 32 binary bits are broken into four
octets (1 octet = 8 bits). Each octet is converted to decimal and separated by a period
(dot). For this reason, an IP address is said to be expressed in dotted decimal format (for
example, 172.16.81.100).
The value in each octet ranges from 0 to 255 decimal, or 00000000 - 11111111 binary.
Here is how binary octets convert to decimal: The right most bit, or least significant bit,
of an octet holds a value of 20. The bit just to the left of that holds a value of 21. This
continues until the left-most bit, or most significant bit, which holds a value of 27. So if
128 64 32 16 8 4 2 1 (128+64+32+16+8+4+2+1=255) Here is a sample octet conversion
when not all of the bits are set to 1. 0 1 0 0 0 0 0 1 0 64 0 0 0 0 0 1
(0+64+0+0+0+0+0+1=65) And this is sample shows an IP address represented in both
binary and decimal. 10. 1. 23. 19 (decimal) 00001010.00000001.00010111.00010011
(binary) There are five IP classes plus certain special addresses:
Default Network :-
The IP address of 0.0.0.0 is used for the default network.
Class A :-
This class is for very large networks, such as a major international company might have.
IP addresses with a first octet from 1 to 126 are part of this class. The other three octets
are used to identify each host. This means that there are 126 Class A networks each with
16,777,214 (224 -2) possible hosts for a total of 2,147,483,648 (231) unique IP addresses.
Class A networks account for half of the total available IP addresses. In Class A
networks, the high order bit value (the very first binary number) in the first octet is
always 0.
Loopback:-
The IP address 127.0.0.1 is used as the loopback address. This means that it is used by
the host computer to send a message back to itself. It is commonly used for
troubleshooting and network testing.
Class B:-
Class B is used for medium-sized networks. A good example is a large college campus.
IP addresses with a first octet from 128 to 191 are part of this class. Class B addresses
also includes the second octet as part of the Net identifier. The other two octets are used
to identify each host. This means that there are 16,384 (214) Class B networks each with
65,534 (216 -2) possible hosts for a total of 1,073,741,824 (230) unique IP addresses.
Class B networks make up a quarter of the total available IP addresses. Class B networks
have a first bit value of 1 and a second bit value of 0 in the first octet.
Class C:–
Class C addresses are commonly used for small to mid-size businesses. IP addresses with
a first octet from 192 to 223 are part of this class. Class C addresses also include the
second and third octets as part of the Net identifier. The last octet is used to identify each
host. This means that there are 2,097,152 (221) Class C networks each with 254 (28 -2)
possible hosts for a total of 536,870,912 (229) unique IP addresses. Class C networks
make up an eighth of the total available IP addresses. Class C networks have a first bit
value of 1, second bit value of 1 and a third bit value of 0 in the first octet.
Class D:–
Used for multicasts, Class D is slightly different from the first three classes. It has a first
bit value of 1, second bit value of 1, third bit value of 1 and fourth bit value of 0. The
other 28 bits are used to identify the group of computers the multicast message is
intended for. Class D accounts for 1/16th (268,435,456 or 228) of the available IP
addresses.
Class E:–
Class E is used for experimental purposes only. Like Class D, it is different from the first
three classes. It has a first bit value of 1, second bit value of 1, third bit value of 1 and
fourth bit value of 1. The other 28 bits are used to identify the group of computers the
multicast message is intended for. Class E accounts for 1/16th (268,435,456 or 228) of
the available IP addresses.
Fig 3.1 IP address
Broadcast:-
Messages that are intended for all computers on a network are sent as broadcasts. These
messages always use the IP address 255.255.255.255.
Address:-
The unique number ID assigned to one host or interface in a network.
Subnet:-
A portion of a network sharing a particular subnet address.
Subnet mask:-
A 32-bit combination used to describe which portion of an address refers to the subnet
and which part refers to the host.
IP addressing:
Given an IP address, its class can be determined from the three high-order bits. Figure
shows the significance in the three high order bits and the range of addresses that fall into
each class. For informational purposes, Class D and Class E addresses are also shown.
❖ IP Header Length (IHL)- Indicates the datagram header length in 32-bit words
❖ Total Length Specifies the length, in bytes, of the entire IP packet, including
the data and header.
❖ Fragment Offset- Indicates the position of the fragment’s data relative to the
beginning of the data in the original datagram, which allows the destination IP
process to properly reconstruct the original datagram.
Subnetting:
By extending the mask to be 255.255.255.224, you have taken three bits (indicated by
"sub") from the original host portion of the address and used them to make subnets. With
these three bits, it is possible to create eight subnets. With the remaining five host ID bits,
each subnet can have up to 32 host addresses, 30 of which can actually be assigned to a
device since host ids of all zeros or all ones are not allowed (it is very important to
remember this). So, with this in mind, these subnets have been created. 204.17.5.0
255.255.255.224 host address range 1 to 30
204.17.5.32 255.255.255.224 host address range 33 to 62
204.17.5.64 255.255.255.224 host address range 65 to 94
204.17.5.96255.255.255.224 host address range 97 to 126
204.17.5.128 255.255.255.224 host address range 129 to 158
204.17.5.160255.255.255.224 host address range 161 to 190
204.17.5.192 255.255.255.224 host address range 193 to 222
204.17.5.224 255.255.255.224 host address range 225 to 254
Types of Subnetting:
Fixed Length Subnet Mask (FLSM)
Variable Length Subnet Mask (VLSM)
FLSM:
Steps of Subnetting for FLSM
For IP address 192.168.10.0 (Class C)
Identify the total no. of subnets 2^n = no.of subnets
Where n are the no.s and borrowed bytes from host ID portion. Let we are given
that we have to make 4 subnets. Therefore 2^n =4 i.e n=2
To idettify the total no. of the valid hosts for each subnet.
2^m-2= no.of valid hosts. Where m are the remaining no. of bits in host ID 2^6-
2=62
Calculate the subnet mask and range
Subnet mask for n/w 192.168.10.0/26 is
11111111.11111111.11111111.1100000000 ie 255.255.255.192
range=> 256-192=64
Identify the total no of subnets, no. of valid hosts and the broadcast address.
VLSM
In VLSM to allocate IP addresses to subnets depending upon the no. of hosts. The
network having more no of hosts is given priority and the one having least no of host
comes at last and for each network the subnet is assigned separately.
Frame Relay:
Frame Relay is still one of the most popular WAN services deployed over the past
decade, and there’s a good reason for this—cost. By default, Frame Relay is classified as
a non-broadcast multi-access (NBMA) network, meaning it doesn’t send any broadcasts
like RIP updates across the network. Frame Relay has at its roots a technology called
X.25, and it essentially incorporates the components of X.25 that are still relevant to
today’s reliable and relatively “clean” telecommunications networks while leaving out
the no-longer-needed error-correction components. It’s substantially more complex than
the simple leased-line networks you learned about when I discussed the HDLC and PPP
protocols, but is still relevant when looking at event the most commonly used networks
from providers such as o2, or other similar companies. The leased-line networks are easy
to conceptualize - but not so much when it comes to Frame Relay. It can be significantly
more complex and versatile, which is why it’s often represented as a “cloud” in
networking graphics.
You won’t be using the encapsulation HDLC or encapsulation PPP command to
configure it.Frame Relay doesn’t work like a point-to-point leased line (although it can be
made to look and act like one).Frame Relay is usually less expensive than leased lines
are, but there are some sacrifices to make to get that savings.
If, for example, you had to add seven remote sites to the corporate office and had only
one free serial port on your router—it’s Frame Relay to the rescue! Of course, I should
probably mention that you now also have one single point of failure, which is not so
good. But Frame Relay is used to save money, not to make a network more resilient.
Take a look at Fig. 43 to get an idea of what a network looked like before and after Frame
Relay.
Bridging loops form because parallel switches (or bridges) are unaware of each other.
STP was developed to overcome the possibility of bridging loops so that redundant
switches and switch paths could be used for their benefits. Basically, the protocol enables
switches to become aware of each other so they can negotiate a loop-free path through
the network.
Loops are discovered before they are made available for use, and redundant links are
effect shut down to prevent the loops from forming. In the case of redundant links,
switches can be made aware that a link shut down for loop prevention should be brought
up quickly in case of a link failure.
STP is communicated among all connected switches on a network. Each switch executes
the spanning-tree algorithm based on information received from other neighbouring
switches. The algorithm chooses a reference point in the network and calculates all the
reduct paths to that reference point. When redundant paths are found, the spanning-tree
algorithm picks one path by which to forward frames and disables, or blocks, forwarding
on the other redundant paths.
As its name implies, STP computes a tree structure that spans all switches in a subnet or
network. Redundant paths are placed in a Blocking or Standby state to prevent frame
forwarding.
The switched network is then in a loop-free condition. However, if a forwarding port fails
or becomes disconnected, the spanning-tree algorithm re computes the spanning tree
topology so that the appropriate blocked links can be reactivated.
MAC Address (6 bytes)—The MAC address used by a switch can come from the
Supervisor module, the backplane, or a pool of 1,024 addresses that are assigned to every
supervisor or backplane, depending on the switch model. In any event, this address is
hard-coded and unique, and the user cannot change it.
As an example, consider the small network shown in Figure. For simplicity, assume that
each Catalyst switch has a MAC address of all 0s, with the last hex digit equal to the
switch label.
Fig 3.5: MAC address
In this network, each switch has the default bridge priority of 32,768. The switches are
interconnected Fast Ethernet links. All three switches try to elect themselves as the
root, but all of them have equal Bridge Priority values. The election outcome produces
the root bridge, determined by the lowest MAC address—that of Catalyst A.
Catalyst A
Because this switch is the root bridge, all its active ports are designated ports, by
definition. At the root bridge, the root path cost of each port is 0.
Catalyst B
Catalyst A port 1/1 is the DP for the Segment A–B because it has the lowest root path cost
(0). Catalyst B port 1/2 is the DP for segment B–C. The root path cost for each end of this
segment is 19, determined from the incoming BPDU on port 1/1. Because the root path
cost is equal on both ports of the segment, the DP must be chosen by the next criteria—
the lowest sender bridge ID. When Catalyst B sends a BPDU to Catalyst C, it has the
lowest MAC address in the bridge ID. Catalyst C also sends a BPDU to Catalyst B, but
its sender bridge ID is higher. Therefore, Catalyst B port 1/2 is selected as the segment’s
DP.
Catalyst C
Catalyst A port 1/2 is the DP for Segment A–C because it has the lowest root path cost
(0). Catalyst B port 1/2 is the DP for Segment B–C. Therefore, Catalyst C port 1/2 will be
neither a root port nor a designated port. As discussed in the next section, any port that is
not elected to either position enters the Blocking state.
STP States
To participate in STP, each port of a switch must progress through several states. A port
begins its life in a Disabled state, moving through several passive states and, finally, into
an active state if allowed to forward traffic. The STP port states are as follows:
Listening—A port is moved from Blocking to Listening if the switch thinks that the port
can be selected as a root port or designated port. In other words, the port is on its way to
begin forwarding traffic.
In the Listening state, the port still cannot send or receive data frames. However, the port
is allowed to receive and send BPDUs so that it can actively participate in the Spanning
Tree topology process. Here, the port finally is allowed to become a root port or
designated port because the switch can advertise the port by sending BPDUs to other
switches. If the port loses its root port or designated port status, it returns to the Blocking
state.
Learning—After a period of time called the Forward Delay in the Listening state, the
port is allowed to move into the Learning state. The port still sends and receives BPDUs
as before. In addition, the switch now can learn new MAC addresses to add to its address
table. This gives the port an extra period of silent participation and allows the switch to
assemble at least some address information. The port cannot yet send any data frames,
however.
Forwarding—After another Forward Delay period of time in the Learning state, the port
is allowed to move into the Forwarding state. The port now can send and receive data
frames, collect MAC addresses in its address table, and send and receive BPDUs.
The port is now a fully functioning switch port within the spanning-tree topology.
Remember that a switch port is allowed into the Forwarding state only if no redundant
links (or loops) are detected and if the port has the best path to the root bridge as the root
port or designated port.
Routing:
Routing is the process of directing packets from a source node to a destination node on a
different network. It is of two types:
Static routing:
The process of manually adding routes in each router's routing table. The administrator
configures the destination network, next hop, and appropriate metrics. The route doesn't
change until the network administrator changes it.
Advantages:-
No overhead on router CPU.
Disadvantages:-
Administrator must really understand internetwork and how each router is
connected.
Dynamic routing:
Dynamic routes adjust to changes within the internetwork environment automatically.
When network changes occur, routers begin to converge by recalculating routes and
distributing route updates. The route update messages spread through the network, which
causes other routers to recalculate their routes. The process continues until all routes have
converged. Uses protocols to find and update routes on a routing table. It uses CPU time
and consumes bandwidth between links. The routing protocol defines the rules used by
the routers when they communicate with each other. There are two types of routing
protocols on internetworks, Interior Gateway Protocol (IGP) and Exterior Gateway
Protocol (EGP). IGP is used in networks in the same administrative domain. EGPs are
used to communicate between the domains.
Routed protocols:
Routed protocols are nothing more than data being transported across the networks.
Routed protocols include:
Internet Protocol
Telnet
SNMP
SMTP
Novell IPX
DECnet
Appletalk
Banyan Vines
Routing protocols:
Routing Protocols are the software that allow routers to dynamically advertise and learn
routes, determine which routes are available and which are the most efficient routes to a
destination. Routing protocols used by the Internet Protocol suite include:
Routing Information Protocol (RIP and RIP II)
TELNET:
Telnet is a protocol which is part of the TCP/IP suite. It is quite similar to the UNIX
rlogin program. Telnet allows you to control a remote computer from your own one. It is
terminal emulation software. In the old days hard drives were humongous and expensive
and there were no personal computers. To make use of existing computers you had to
lease hard rive space and use terminals to operate the system. For developers this was
great because computing became lots cheaper. You needed a server and many
connections could be made. With telnet u can emulate this type of distributed computing
and for example operate a supercomputer from a distance.
Introduction:
The project is a communication model which represents a mesh of networking elements
including routers, switches, servers (DHCP and DNS in this model), frame relay, access
points, computers and different types of cables to connect them. The project is based on
the technology of Hardware and Networking, typically on CCNA (Cisco Certified
Network Associate). The essence of this project lies in the configuration of these network
elements so that they can communicate with each other as required by the network
administrator.
The kind of access rights given to each network element and the services each computer
can use depends on the configuration done by the network administrator. The project
typically shows the communication model for an organization with its two branches and
one headoffice. The objective of planning such a network model is to make easy the task
of actual set up of a network. The communication model prepared (as in this project) acts
as a guide while connecting the real computers and other network devices like routers,
switches, and different types of servers. The detailed objectives are given as:
Easy to set up actual network:
It becomes so easy to set up an network that is
prepared in the model. It acts in similar way as a map of a building to be built. As it is so
difficult job to construct a house whose map is not available, similarly it is very
cumbersome job to start connecting a lot of networking devices available in absence of a
model.
IP addressing:
Assigning the IP addresses to the network is the first and the most
important task. IP addresses are actually unique addresses to each network element. It is
the unique code that identified the network element in the network. In the network model,
we have all the elements visible to us at a time, so we can assign them IP addresses
easily, but the same job will be difficult to do on a group of computers, at different
locations.
Easy to make changes and extend the network:
It becomes easy to make further
changes in the network if is network model is available. We can have a look on the
settings and the implementations already done on it and so can modify it. the same job is
really hectic to be done on actual network and can result the introduction of errors in it.
Easy to understand:
A network can be easily understood for its structure,
characteristics and configuration from the network model. In the absence of this, each
network element will need to be visited at different locations and checked for its
configuration.
Estimation of the computers and hardware required:
Any organization first prepares a
network model, before actual set up. The main things like number of departments, ad
number of computers in each department etc. are taken care of while preparing the
network model. After the network model is ready, the organization can easily estimate
the cost required to have such network, the type of network elements required and the
number of these, thereby avoiding the wastage.
Cabling:
Different network elements needed to be connected by different types of
cables. In actual, mistake can be done while connecting different elements with wrong
type of cables and on the wrong interfaces as well. But a network model provides the
types of cables and the detail of interfaces on which they should be connected, which
helps a lot while its actual implementation.
Configuration of network:
A lot of computers, routers and switches connected together can’t
be called a network. Configuration is to be done on each network element that decides
the
working of network. All that configuration is already done in the network model. It is
easy to do the configuration on the model itself than to do the same on the actual network
first time. This will cause a lot of time waste and errors as well. When we have a network
model, we can easily see the configuration done in the model and can implement the
same on the actual network. This reduces the errors and saves the time.
Routing protocols:
Whenever a group of elements are connected in a network, a routing
protocol must be used in order to tell each network element the way or path to use for
transmitting a packet from a particular source to the destination. The routing protocols
are also implemented in a communication model much easily. The software used for the
development of the project is “cisco packet tracer” whose opening window is shown
below in the figure. This work area is used to prepare the network model. Here we can
select the necessary hardware needed to prepare the model and also can alter its
properties such as, we can add interfaces to the routers, wireless LAN cards to the
computers.
two similar kind of devices, eg both DTE or DCE, then a cross cable (shown with dotted
lines) will be used. And when different types of devices are being connected, like one
DTE and other DCE, the n serial cables will be used (with an exception of routers).
Project Details:
The network model which we are designing will be consisting of routers, switches,
computers, servers, hubs. All the above elements together represent an organization. In
project, different technology of networking is implemented. These technologies are like
named below:
Routing protocol : OSPF (Open Shortest Path First Protocol)
HTTP
DNS
DHCP server
Here in the figure, the complete model is shown which has been constructed in the
project. Each part of the organization has been given a different background color and
according to the configuration done on it.
Fig 4.4: Project Outlay
When ever any computer in the communication model is selected, packet tracer shows
the window, shown in the figure below. This window basically shows the options that
any computer have. E.g. command prompt, option to allocate IP address etc. we can use
any of the service to ensure that the terminal connected is working correctly in the
network.
Fig 4.5: The options available for a Laptop/ Terminal
Below is the example given to check if one computer is communicating to another. This
is done by using “ping” command in the command prompt. Typing the keyword “ping”
and then the IP address shows the result. The reply is shown from the address to which
we wanted to communicate, if they are connected in right manner, or not blocked
explicitly, otherwise, failure is shown.
Fig 4.6: Using Ping Command
Chapter 5
Conclusion and Future Scope
Computer Networking is a very vast project in the present developing era of electronics
and communication. Now days, computers are used in a wider range. All the
organizations are using multiple computers within their departments to perform their day
to day work. Computer network allows the user to share data, share folders and files with
other users connected in a network. Computer Networking has bound the world in a very
small area with it wide networking processes like LAN, MAN, WAN. Networking inside
your organization is valuable also. In larger companies, many people never meet others in
the organization that can facilitate solving problems or getting resources. This project is
forward compatible as we can add more branches at low cost and high efficiency with
effective communication between head office and various branches of an organization.
References
The following web links are visited for the theory reference:
http://www.cisco.com/web/learning/netacad/course_catalog/PacketTracer.html
http://www.cisco.com/web/learning/netacad/index.html
http://www.cisco.com/en/US/docs/internetworking/technology/handbook/ito_doc.html
http://netcert.tripod.com/ccna/routers/routeprotocols.html
http://www.livinginternet.com/i/iw_route.htm
http://en.wikipedia.org/wiki/Dynamic_Host_Configuration_Protocol
http://www.isc.org/software/dhcp
http://www.cisco.com/web/IN/products/routers/index.html
http://www.webopedia.com/TERM/R/router.html