Professional Documents
Culture Documents
SD470Test2010
SD470Test2010
TEST
2009/2010 ACADEMIC YEAR
1st SEMESTER
INSTRUCTIONS
Closed book examination
Duration: 1 hour 45 minutes
Total marks: 100%
Answer all TWO questions given in this paper
Remember to indicate the question answered on the top page of the answer book
© Dr JK Makunza – 2010
2
Problem No. 1. (60%)
The bridge transversal section shown in Figure 1 has a longitudinal effective span of
15.00m. If the density of concrete is 24 kN/m3 and that of surfacing course material is 18
kN/m3, and assuming that the thickness of wearing course in 32mm at the ends, and that
there are 30 units of HB in which each unit is 2.5 kN per wheel, perform the following
tasks;
1.1 Calculate the ultimate loads considering transversal direction only, and sketch the
following:
i. HA loading alone
ii. Superimposed dead loads
iii. Dead loads
iv. HA + HB loading combination
1.2 Determine the transversal bending moment due to HA loading alone.
1.3 What is a scour effect in bridge operation? What precautions must be taken against
scour during design stage and construction of a bridge?
Table: 1: Notional lanes for design purposes according to the carriageway width
Carriage Width W(m) < 4.6 4.6-7.5 7.6-11.4 11.4-152 15.2-19.0
No.of Notional Lanes W/3 2 3 4 5
.
Table 2: HA Loading
Loaded length L (m) < 30m 30m - 379m > 379m
Uniform Load (k N/m/Lane) 30 151 L0.475 9
Knife edge load(kN/Lane) 120
HB Loading
The length of the vehicle is varied for the severest effect by dimensions shown in Figure 3.
Figure 2: HB Vehicle
Load Combinations
Principal Load Combinations
Combination 1: permanent + imposed loads
Combination 2: permanent + imposed + wind loads
Combination 3: permanent + imposed + constraining loads
Secondary Combinations
Combination 4: permanent + collision loads
Combination 5: permanent + friction loads at bearings
5
SOLUTIONS
Question No. 1
1.1 Calculations of ultimate loads
(i)HA Load alone
Loaded length = 15.00 m
Carriageway width = 6.00 m
Number of notional lanes = 2
Width of each lane = 3.00 m
(iv) HA with HB
UDL: 30 x 1.3/3.0 = 13.00 kN/m2
KEL: 120 x 1.3/3.0 = 52.00 kN/m (transversal line load)
(iv) HA + HB
Pedestrian Load
1.3 Scour occurs during the passage of high discharge, when the
velocity of the stream exceeds the limiting velocity that can be
withstood by the particles of the bed material, the effect of which
erosion of the river bed. Therefore, during design stage the scour
depth has to be determined and during construction, the
foundations must be below the scour depth so as to prevent its
occurrence.
Problem 2 (40%)
2.3 The function of wing walls is to retain the approach road embankment and to
Stabilize the abutment
2.5 Bearings are provided at the interface between the superstructure and the
substructure in bridges. The main functions of bearings are:
i) To transmit the vertical loads from the superstructure to the substructure like piers and
abutments
ii) To accommodate movements due to thermal changes resulting in expansion or
contraction
iii) To allow for rotation of the beams or bridge girders
2.7 The various alternatives for determining the severe case of loading for HA and HB are
as follows:
- Full HA on both lanes
- Full HA on one lane + HB on the second lane
- Full HA on single lane