Professional Documents
Culture Documents
Παράρτημα
Παράρτημα
Αξιοπιστία Κίτρινο 4
Ανοχή Πράσινο 5
Αριθμός μηδενικών
Μπλε 6
2ος αριθμός
1ος αριθμός Μωβ 7
Στον Πίνακα Ι.1 φαίνεται η αντιστοιχία των χρωμάτων των δακτυλίων με αριθμούς.
Π.χ. αν οι δακτύλιοι μιας αντίστασης έχουν κατά σειρά τα χρώματα: πορτοκαλί,
λευκό, κίτρινο, χρυσαφί (όπως στην αντίσταση του σχ.Ι.1), τότε η τιμή της
αντίστασης θα είναι 390000 Ω (ή 390kΩ) ±5%.
ΠΑΡΑΡΤΗΜΑ ΙI
Παλμογράφος
Ο παλμογράφος είναι ένα όργανο με το οποίο μπορούμε να αποτυπώνουμε και να
μετράμε τάσεις και συγκεκριμένα το δυναμικό ενός σημείου του κυκλώματος ως προς
τη «γη».
Με τον παλμογράφο μπορούμε να μετρήσουμε τόσο συνεχείς όσο και μεταβλητές
τάσεις.
Σε ένα περιοδικό σήμα μπορούμε να μετρήσουμε την τιμή από κορυφή σε κορυφή
(pp), το πλάτος, τη χρονική μέση τιμή (συνεχή-DC συνιστώσα) και την περίοδο.
3. SPECIFICATION
GFG- GFG-
GFG- GFG- 8215A/8216A/8217A/8219A 8250A/8255A
8215A/8216A/8217A/8219A 8250A/8255A 5.CMOS Output
1.Main 4Vpp±1Vpp~14.5Vpp 4Vpp±1Vpp~14.5Vpp
Level
Frequency Range 0.3Hz~3MHz(7 Range) 0.5Hz~5MHz(7 Range) ±0.5Vpp adjustable ±0.5Vpp adjustable
Amplitude ≧10Vpp(into 50Ωload) ≧10Vpp(into 50Ωload) Rise or Fall Time ≦120ns ≦120ns
Impedance 50Ω±10% 50Ω±10% 6.TTL Output
Attenuator -20dB±1dB×2 -20dB±1dB×2 Level ≧3Vpp ≧3Vpp
<-5V~>5V <-5V~>5V Fan Out 20 TTL load 20 TTL load
DC Offset Rise or Fall Time ≦25ns ≦25ns
(into 50Ωload) (into 50Ωload)
80%:20%:80% to 1MHz 80%:20%:80% to 1MHz 7.VCF
Duty Control
Continued variable Continued variable Input voltage 0V~10V±1V(100:1) 0V~10V±1V(100:1)
6 digits LED display Input Impedance 10kΩ±10% 10kΩ±10%
Display *GFG-8215A does not have 6 digits LED display 8.GCV(for GFG-8219A/8255A only)
display. To set the voltage between To set the voltage between
±5%+1Hz(at 3.0 position) Output voltage 0V~2V as per different 0V~2V as per different
Range Accuracy ----------------------------
*only for GFG-8215A. frequency. frequency.
2.Sine Wave 9.Sweep Operation(for GFG-8217A/8219A/8255A only)
Sweep/Manual Switch selector Switch selector
Sweep/Rate 100:1 ratio max. and adjustable 100:1 ratio max. and adjustable
Distortion ≦1%,0.3Hz~200kHz ≦1%,0.5Hz~100kHz
Sweep/Time 0.5Sec~30Sec adjustable 0.5Sec~30Sec adjustable
Sweep/Mode Lin./Log. switch selector Lin./Log. switch selector
<0.3dB,0.3Hz~300kHz ≦0.3dB,below 500kHz 10.Amplitude Modulation(for GFG-8219A/8255A only)
Flatness <0.5dB,300kHz~3MHz ≦1dB,below 5MHz Depth 0~100% 0~100%
3.Triangle Wave MOD.Freq. 400Hz(INT),DC~1MHz(EXT) 400Hz(INT),DC~1MHz(EXT)
≧98%,0.3Hz~100kHz ≧98%,0.5Hz~100kHz Carrier BW 100Hz~3MHz(-3dB) 100Hz~5MHz(-3dB)
Linear ≦10Vpp for 100% modulation ≦10Vpp for 100% modulation
≧95%,100kHz~3MHz ≧95%,100kHz~5MHz EXT Sensitivity
4.Square Wave
Symmetry ±2%,0.3Hz~100kHz ±2%,1Hz~100kHz
≦100ns at maximum output. ≦50ns at maximum output
Rise or Fall Time
(into 50Ωload) (into 50Ωload)
7 8
FUNCTION GENERATOR-SERIES FUNCTION GENERATOR-SERIES
INSTRUCTION MANUAL INSTRUCTION MANUAL
GFG- GFG-
GFG- GFG- 8215A/8216A/8217A/8219A 8250A/8255A
GTL-101×2 GTL-101×2
8215A/8216A/8217A/8219A 8250A/8255A Accessories *GTL-101×1 for GFG-8215A Instruction manual×1
11.Frequency Modulation (for GFG-8219A/8255A only) Instruction manual×1
Deviation 0~±5% 0~±5% Dimension 251(W)×91(H)×291(D) m/m 251(W)×91(H)×291(D) m/m
MOD.Freq. 400Hz(INT),DC~20kHz(EXT) 400Hz(INT),DC~20kHz(EXT) Approx. 2.0kgs-GFG-8215A Approx. 2.3kgs-GFG-8250A
2.1kgs-GFG-8216A 2.4kgs-GFG-8255A
EXT Sensitivity ≦10Vpp for 10% modulation ≦10Vpp for 10% modulation Weigh
2.15kgs-GFG-8217A
12.Frequency Counter 2.2kgs-GFG-8219A
Int./Ext. Switch selector Switch selector Measurement category I is for measurements performed on circuits not
0.3Hz~3MHz 0.5Hz~5MHz directly connected to MAINS.
Range
(5Hz~150MHz EXT) (5Hz~150MHz EXT) Measurement category II is for measurements performed on circuits directly
Accuracy Time base accuracy±1count Time base accuracy±1count connected to the low voltage installation.
±20ppm(23℃±5℃) after ±20ppm(23℃±5℃) after Measurement category III is for measurements performed in the building
Time base
30 minutes warm up 30 minutes warm up installation.
The maximum resolution is 10nHz The maximum resolution is Measurement category IV is for measurements performed at the source of
Resolution for 1Hz and 10nHz for 1Hz and the low-voltage installation.
0.1Hz for 100MHz. 0.1Hz for 100MHz.
Input Impedance 1MΩ/150pF 1MΩ/150pf WARNING : To avoid electrical shock, the power cord
≦35mVrms(5Hz~100MHz) ≦35mVrms(5Hz~100MHz) protective grounding conductor must be connected to ground.
≦45mVrms(100MHz~150MHz) ≦45mVrms(100MHz~150MHz)
Sensitivity CAUTION:To avoid damaging the instrument, do not use it
*GFG-8215A does not have
Frequency Counter function. In a place where ambient temperature exceeds 40℃.
13.General CAUTION:To avoid damaging the instrument, do not input
Power Source AC115V, 230V±15%,50/60Hz AC115V, 230V±15%,50/60Hz more than DC15V to V.C.F.(V.C.G.).
Indoor use, altitude up to 2000m.
Ambient Temperature 0℃ to 40℃. CAUTION:To avoid damaging the instrument, do not input
Operation more than AC150V to Frequency Counter (for GFG-8216A,
Environment Relative Humidity 80%(Maximum).
Installation category II GFG-8217A, GFG-8219A, GFG-8250A, and GFG-8255A).
Pollution Degree 2
Storage temperature -10℃ to 70℃. CAUTION:To avoid damaging the instrument, do not input
& Humidity 70% (Maximum). more than AC10Vpp when proceed EXT modulation
operation (for GFG-8219A, GFG-8255A).
9 10
FUNCTION GENERATOR-SERIES FUNCTION GENERATOR-SERIES
INSTRUCTION MANUAL INSTRUCTION MANUAL
11 12
FUNCTION GENERATOR-SERIES FUNCTION GENERATOR-SERIES
INSTRUCTION MANUAL INSTRUCTION MANUAL
6. Gate Time Indicate the current Gate time (external. counter mode 11. DC Offset Control Pull out the knob to select any DC level of the
Indicator use only). waveform between ± 10V, turn clockwise to set a
positive DC level waveform and invert for a negative
7. Frequency Range To select the required frequency range by pressing the DC level waveform.
Selector relevant push button on the panel as shown in
Table 1 and Table 2. 12. Output Amplitude Turn clockwise for MAX. output and invert for a –20dB
Control with output. Pull the knob out for an additional 20dB output
Attenuation attenuation.
Operation
13 14
FUNCTION GENERATOR-SERIES FUNCTION GENERATOR-SERIES
INSTRUCTION MANUAL INSTRUCTION MANUAL
12a. 20dB Attenuation Press the knob to adjust a –20dB output. 19. EXT. Counter Accepts external signals for measurement.
Input Terminal
13 MANU/SWEEP Press and turn clockwise the knob for MAX frequency
Selector and and invert for MIN frequency. (Keep the pointer within 20. TTL/CMOS TTL/CMOS compatible signal output
Frequency the scale range on the panel.). Output Terminal
Adjustment Pull out the knob to start the auto sweep operation; the
(Sweep On/Off) upper frequency limit is determined by the knob 21. VCF/MOD Used to connect the input voltage required to perform
position. Input Terminal the “voltage control frequency” operation or the EXT
modulation operation.
14 Sweep Time (1) Rotate the knob clockwise to adjust sweep time for
Control and MAX, or invert for MIN. 22. Main Output Main signal output.
LIN/LOG (2) To proceed Linear sweep mode by pushing in the Terminal
Selector knob, or select LOG sweep mode by pulling out the
knob. 23. GCV Output This is DC voltage output and its voltage amount will
follow the change of Frequency.
15. Control MOD Pull out the knob, the output can be modulated by
ON/OFF Selector internal 400Hz Sine wave or an external signal via 24. Power Switch 115V and 230V selectable.
VCF/MOD in connector 21 .
z Remark:
16. Sweep Width & (1) Sweep width can be controlled from 0 to 1000 times. (1) The functions of item 2, 2a, 3, 4, 5, 6, 14, 15, 16, 17, 19 and 23 can
Modulation (2) To adjust modulation ratio by turning the knob
not be applied to model GFG-8215A.
Carrier &AM/FM clockwise for MAX, or invert for MIN.
Selector &FM (3) Press the knob to get AM function or pull it out for (2) The functions of item 14, 15, 16, 17 and 23 can not be applied to
Selector FM function. GFG-8216A, and GFG-8250A.
(3) The function of item 15, 16-2, 16-3, 17 and 23 can not be applied to
17 INT/EXT MOD When press the button once, the indicator will lighten,
Selector then the EXT MOD has been selected. Press the key GFG-8217A.
again, the indicator will be off, then INT MOD has been (4) The function of item 20 for GFG-8216A/8250A can be selected
selected. from front panel.
(5) The function of item 20 and 21 for GFG-8215A can be selected
18. INT/EXT Counter Select internal counter mode (count the frequency of
Selector model) or select EXT counter mode for an independent from front panel.
counter (input signal from BNC 19 ).
15 16
FUNCTION GENERATOR-SERIES FUNCTION GENERATOR-SERIES
INSTRUCTION MANUAL INSTRUCTION MANUAL
5-1.First-step check:
(1) Ensure that the voltage of the main supply is compatible with this
instrument. The label on the rear panel states the required AC
voltage.
(2) Connect the instrument to the main supply using the power cord
supplied.
(3) Press PWR switch 1 and ensure all the rotary controls are pushed in,
then rotate AMPL 12 knob to make the indication point up forward.
(4) Rotate the FREQ 13 control fully anticlockwise.
17 18
FUNCTION GENERATOR-SERIES FUNCTION GENERATOR-SERIES
INSTRUCTION MANUAL INSTRUCTION MANUAL
19 20
FUNCTION GENERATOR-SERIES FUNCTION GENERATOR-SERIES
INSTRUCTION MANUAL INSTRUCTION MANUAL
5-8.AM/FM operation
(1) Select function 8 first; then select Range 7 , rotate FREQ 13 to set z Figure 2.
required frequency range.
(2) Connect output terminal 22 to oscilloscope for observing output
signal.
(3) Press MOD 15 and pull out (press) MOD 16 to obtain FM/AM
modulation mode.
(4) Adjust MOD 16 to achieve required modulation ratio.
21 22
FUNCTION GENERATOR-SERIES FUNCTION GENERATOR-SERIES
INSTRUCTION MANUAL INSTRUCTION MANUAL
6. APPLICATION NOTE
(D) Using the Square wave test the characteristics of amplifier circuit.
This section describes the application of the Function Generators in It can’t actually explain the transient response of amplifier by using
details as well as a brief description relating to the block diagram. Only for Sine wave for the frequency response curve observation, but using the
the essential application method. high order poly-wave, Square wave, instead to display its waveform
from the oscilloscope can show up many characteristics of amplifier.
(A) Trouble-shooting using signal-tracing method. (a) Using the circuit of figure 5, the 50 Ω connector trim the
This method is similar to signal replacing way. The signal of model oscillation effect of Square wave.
will be fixedly sent to input terminal. Observing its signal wave on the (b) Use the output of Triangle wave, adjust the amplitude until there
oscilloscope from front stage to rear stage orderly until appear a signal are no clipping happened in the applied frequency.
with normal input but with abnormal output. (c) Select Square wave, adjust frequency, choose to watch the wave-
form of middle of amplifier pass band, like 20Hz, 1kHz, 10kHz
(B) Use as bias source and signal source circuit. and etc.
Utilize the Figure 4 of connecting type, which can provide bias of a (d) The output waveform of (c), must get something with frequency
transistor and signal input. The output waveform can be observed from Figure 6 shows some possible conditions.
oscilloscope. Adjust to the best condition with output max. amplitude
and no distortion. Adjust DC OFFSET to see the different effect of CAUTION: The composed poly-wave frequency of
different bias condition. Square wave is quite large, so it’s not suitable for the
narrow band amplifier testing.
(C) Amplifier over-load characteristics
The Sine wave input will be different from output the overload point. (E) Test of logic circuit
Using Triangle wave will easily observe the display of oscilloscope. It This equipment is suitable for logic circuit testing. Using Square or
can decide the linear range of output waveform. And the largest no- Pulse wave can analyze or watch the frequency waveform of a
distortion output amplitude. designed testing circuit. Also the DC Offset effect, drive the plug-in
model board or logic circuit trouble-shooting and etc. Used as signal
tracing and signal replacing operation:
23 24
FUNCTION GENERATOR-SERIES FUNCTION GENERATOR-SERIES
INSTRUCTION MANUAL INSTRUCTION MANUAL
(a) Connect the lines as Figure 7. (1) Series connect a R1 to the network under test as in Figure 9.
(b) According to the operation guide in this manual, set Square wave or (2) Get voltage read out in E1, E2, adjust R1 until E2 is equal to one
Pulse wave output. half of E1.
(c) Use the label TTL, CMOS output terminal testing TTL logic circuit. (3) Under this frequency, the impedance network is the same as the
(d) To test CMOS circuit by pulling up the switch of TTL/CMOS, and R1.
adjust CMOS level by rotating the switch to set the proper level
(e) Use dual-trace scope to show the input-output timing relation (G)Act as automatic test of speaker
judged by the two waves shown in Figure 4. Because there provide the auto feature in this equipment, the output can
drive to amplifier for testing the frequency response of speaker.
(F)Testing of speaking and impedance network (a) Set Auto/Manual to Auto position.
This equipment can be used to test the frequency characteristics of (b) Set function to Sine wave
speaker or any impedance network. It also can get the resonant (c) Set Range to 20kHz
frequency of network. (d) Sweep mode (LIN, LOG), sweep width, sweep time can be set in
(a) Connect the device under test as in Figure 8, can use oscilloscope in any value.
stead of voltmeter. (e) The line connected is showed in Figure 11.
(b) When use voltmeter, adjust the frequency of instrument record
down voltage relative to frequency.
(c) When testing speaker, if there is a peak volt value, when in low
freq., this must be the resonant freq. of this speaker, see Figure 10.
Whether installation may cause any effect to this frequency or not?
The proper design of case-installation will cause two small ramps
on both sides of this sharp ramp.
(d) In testing other impedance network, the resonant may not occur in
low frequency. But in approaching the resonant frequency, there
are still increasing in voltage, then the impedance can be tested as
following:
25 26
FUNCTION GENERATOR-SERIES FUNCTION GENERATOR-SERIES
INSTRUCTION MANUAL INSTRUCTION MANUAL
z FIGURE 4 z FIGURE 5
27 28
FUNCTION GENERATOR-SERIES FUNCTION GENERATOR-SERIES
INSTRUCTION MANUAL INSTRUCTION MANUAL
z FIGURE 7
z FIGURE 6
z FIGURE 8
29 30
FUNCTION GENERATOR-SERIES FUNCTION GENERATOR-SERIES
INSTRUCTION MANUAL INSTRUCTION MANUAL
z FIGURE 9 z FIGURE 11
z FIGURE 10
31 32
ΠΑΡΑΡΤΗΜΑ ΙV
Ο τελεστικός ενισχυτής LM741.
1FEATURES DESCRIPTION
•
2 Overload Protection on the Input and Output The LM741 series are general purpose operational
amplifiers which feature improved performance over
• No Latch-Up When the Common Mode Range industry standards like the LM709. They are direct,
is Exceeded plug-in replacements for the 709C, LM201, MC1439
and 748 in most applications.
The amplifiers offer many features which make their
application nearly foolproof: overload protection on
the input and output, no latch-up when the common
mode range is exceeded, as well as freedom from
oscillations.
The LM741C is identical to the LM741/LM741A
except that the LM741C has their performance
ensured over a 0°C to +70°C temperature range,
instead of −55°C to +125°C.
Connection Diagrams
LM741H is available per JM38510/10101
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2 All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 1998–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
LM741
SNOSC25C – MAY 1998 – REVISED MARCH 2013 www.ti.com
Typical Application
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
(1) “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits.
(2) For military specifications see RETS741X for LM741 and RETS741AX for LM741A.
(3) If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
(4) For operation at elevated temperatures, these devices must be derated based on thermal resistance, and Tj max. (listed under “Absolute
Maximum Ratings”). Tj = TA + (θjA PD).
(5) For supply voltages less than ±15V, the absolute maximum input voltage is equal to the supply voltage.
(6) Human body model, 1.5 kΩ in series with 100 pF.
(1) Unless otherwise specified, these specifications apply for VS = ±15V, −55°C ≤ TA ≤ +125°C (LM741/LM741A). For the LM741C/LM741E,
these specifications are limited to 0°C ≤ TA ≤ +70°C.
2 Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Thermal Resistance CDIP (NAB0008A) PDIP (P0008E) TO-99 (LMC0008C) SO-8 (M)
θjA (Junction to Ambient) 100°C/W 100°C/W 170°C/W 195°C/W
θjC (Junction to Case) N/A N/A 25°C/W N/A
SCHEMATIC DIAGRAM