Professional Documents
Culture Documents
ABAQUS-AQUA_tutorial-basics
ABAQUS-AQUA_tutorial-basics
XXX
Table of contents
The challenge
Model Set-Up
Defining offshore environment: current and waves
Defining load due to current and waves
Requesting output for visualisation
Results: reaction force in fully constrained model
Results: stress and deformation in beam fixed to ocean floor
Interested in discussing your challenge with us, to see if we can be of help with our FEA consulting
services?
Offshore structures are often loaded due to water and wind. The loads on the structure may vary in
time and with position. It is possible to specify such loads in Abaqus directly. When applying these
types of loads to beams, it may be easier to use Abaqus/Aqua.
Within Abaqus/Aqua the environment of a structure can be defined including a steady current,
waves and a wind profile. Based on this environment, loads due to drag, buoyancy and inertia can
be defined.
The Abaqus/Aqua options are not available from the CAE. In this blog, I will show how to define a
current and Airy waves and apply a drag load based on this using the keyword editor.
The challenge
As example a circular beam with a diameter of 0.2 m and a length of 60 m is simulated. It is fixed to
the ground and partially under water; the still water level is at 44 m. A current is specified in x-
direction with a velocity of 0 at the ocean floor which increases linearly with height to 0.1 m/s at 44
m. Two sets of Airy waves are defined. One has a height of 0.25 m and a wavelength of 2 m. It
travels in the x-direction. The other has a height of 0.2 m, a wavelength of 1.5 m and it travels at an
angle of 45 degrees with respect to the x-axis in the x-y plane.
Model Set-Up
A part is defined for the beam. This must be a wire, to allow Abaqus/Aqua loads to be calculated. A
material model, profile and section are created and assigned. The part is instanced into the assembly
and oriented in such a way the z-direction corresponds to the vertical direction. This is assumed by
Abaqus/Aqua for 3D simulations; for 2D simulations the y-direction should correspond to the
vertical direction. A step is created and appropriate boundary conditions are applied.
To visualise the waves, a shell part is created besides the beam. A mesh of surface elements are used
for this part, and no properties are assigned to it. It is placed in such a way that is forms the still
water surface, so horizontally at the still water height.
The environment is defined using the *AQUA keyword. As can be checked in the Abaqus
Keywords Reference Guide, the keyword should be placed at the model level (for example just
before the step definition) and the syntax is as follows:
*AQUA
Elevation of the seabed, elevation of the still fluid surface, gravitational constant, mass density of
the fluid
Steady velocity of the fluid in the X-direction, steady velocity of the fluid in the Y-direction, Steady
velocity of the fluid in the Z-direction (only relevant for 3D cases), elevation, X-coordinate defining
the location where the velocity applies (if this value is omitted the velocity is assumed to be
independent of X-direction), Y-coordinate defining the location where the velocity applies (only
relevant for 3D; if omitted, velocity is assumed to be independent of Y)
This last line can be repeated as often as required to define the velocity of the current at different
positions.
So, for the specified problem, where the seabed is at z=0 and SI units are used, this leads to:
Note that the specified velocity is interpolated linearly between the points at which it is defined.
With this the current is defined, but the waves are not. This required the *WAVE keyword. For Airy
waves (linear waves with small height compared to water depth) the syntax is as follows:
*WAVE, TYPE=AIRY
Wave component amplitude, wavelength of this component, phase angle of this component, x-
direction cosine defining the direction of travel for this wave component, y-direction cosine
defining the direction of travel for this wave component (not needed in 2D cases).
The last line can be repeated as often as necessary to define all wave trains. The direction cosine is
the cosine of the angle between the vector corresponding to the direction of travel of the wave and
the specified direction (x- or y-axis). In two-dimensional cases only one directional cosine is
needed, where +1.0 indicates a wave travelling in the direction of increasing x, while -1.0 indicates
a wave travelling in the direction of decreasing x.
*DLOAD
Element number or set, FDD, magnitude, effective outer diameter of the member, drag coefficient,
structural velocity factor, amplitude for scaling current velocities, amplitude for wave velocities.
Here FDD specifies that it is a fluid drag load. The calculated force is multiplied by the specified
magnitude and amplitude, as is common for other loads in Abaqus as well. The effective outer
diameter can differ from the beam diameter, to take into account material providing drag, but not
influencing structural properties. In this example, the effective outer diameter will be taken to match
the diameter of the beam. The structural velocity factor defaults to 1, and this value is used in this
simulation. This leads to:
First an element set corresponding to all surface elements in the part is made on the part level. In
this case, the set is named Set-1. The following syntax can then be used:
No loads or boundary conditions should be applied to the surface. If displacement output is
requested for it, the deformation of the sea surface due to the waves will be visible in the .odb.
VIDEO1
VÍDEO2
website: https://simulation-blog.technia.com/simulation/modelling-loads-of-steady-current-and-
waves-with-abaqus-aqua