Professional Documents
Culture Documents
EV30PSPE_C-41RANP
EV30PSPE_C-41RANP
EV30PSPE_C-41RANP
MODEL: Q S F - V 3 0P
Specifications
Specifications
Processable film sizes 135, 126, 110, 120, 220 and IX240
Circulation pumps Corrosion resistant magnetic pumps with sensors to detect pump
rotation.
Collection of waste solutions Waste solutions are pumped into inner waste solution tanks.
Solution upper level alarm is provided.
1
Approximate production capacity Film size Capacity (rolls/hour)*
120 32
220 18
126 (12 EXP.) 48
126 (24 EXP.) 32
135 (12 EXP.) 38
135 (24 EXP.) 26
135 (36 EXP.) 20
110 (12 EXP.) 50
110 (24 EXP.) 34
IX240 (15 EXP.) 34
IX240 (25 EXP.) 26
IX240 (40 EXP.) 18
2
Features
2. Developing time (processing speed) can be set to either the 3 step variable mode or to the stepless
variable mode.
6. Two different sizes of film can be processed at the same time using right and left lanes.
Since the film size is detected for each lane, any combination of sizes other than 120 and IX240 can be
processed, simultaneously. (120 film must be processed by itself or with another roll of 120 film. IX240 film
also must be processed by itself.)
7. Energy conservation
To save as much energy as possible, the dryer goes on and off automatically. This ensures that the dryer
is activated only when film is being processed.
3
12. Automatic film size detection
In accordance with a signal received from the sensor, the size of the film is detected automatically.
Then, in turn, the amount of replenisher and all other relevant decisions are made automatically.
16. All necessary maintenance can be carried out from the same side.
Since the machine can be completely checked and maintained from just one side, it can be installed close
to a wall, allowing for optimum use of valuable floor space.
4
1270
50 1010 210
540
147
5
658
1066
Dimensions
261
325
Unit: mm
1839 (Minimum height required
to remove the processing racks.)
Space required for installation
400 or more
100 or more
500 or more
400 or more
1866 or more
1140 or more
Unit: mm
6
Processing information
*1 When the processing speed changeover switch is set to channel 3, you can adjust the processing speed as you like with
the potentiometer on the switch panel. But be aware that the processing speed is to be within the range, 3'15" to 4'15".
Step C-41RANP
Capacity of CD 7.6
processing BL 3.1
tanks ( ) FIX 5.4
STB 5.7
Capacity of CD
replenisher BL
*2 12 each
tanks ( ) FIX
STB
Capacity of CD 2.4
waste solution BL 0.9
tanks ( ) FIX 4.3
STB 4.5
Cooling water 20℃, 2 /min
(When a chilling unit is not used.)
As long as the temperature surrounding the machine is kept
at 30℃ or below, cooling water is unnecessary.
But when it is higher than that, cooling water is required.
There are two ways of controlling solution temperatures, one
is by using city water and the other is by using a chilling unit
(sold separately). In either case, a cooling water unit (option)
must be attached to the machine.
Capacity of
refilling water *2 5
tanks
*2 When the amount of solution remaining in a replenisher tank reaches approximately 1 liter, an alarm is given.
7
Power requirements
・The values appearing in the table below show the capacity required when installing the power source.
・Supply voltage should be within a ±10% range of the specified voltage.
Wiring chart
Distribution box
Power source
(1P2W AC200 - 240V)
Ground
Film processor
8
Power requirements
・The values appearing in the table below show the capacity required when installing the power source.
・Supply voltage should be within a ±10% range of the specified voltage.
Wiring chart
Distribution box
Power source
(3P3W AC200 - 240V)
Ground
Film processor
8
Power requirements
・The values appearing in the table below show the capacity required when installing the power source.
・Supply voltage should be within a ±10% range of the specified voltage.
Wiring chart
Distribution box
Power source
(3P4W AC346 - 415V)
Ground
Film processor
8
Standard equipment
Film stocker 1
Castors Already attached.
Program timer Built-in
Film counter (total appears on display) Built-in
Film counter for each size (appears on display) Built-in
Automatic water replenisher Built-in
Loading box interlock system Built-in
Solution overheat prevention system Built-in
Automatic replenishment calculator Built-in
Surge absorber Built-in
Solution level alarm Built-in
Replenisher solution low level alarm Built-in
Circulation pump stop alarm Built-in
Waste solution level alarm Built-in
Drive stop alarm Built-in
Dryer fan stop alarm Built-in
Internal replenisher mixing unit Built-in
Waste solution tanks Buit-in
Floppy disk drive for data backup Built-in
9
Standard accessories
C-ring #4 10
C-ring #6 2
Bushing for processing rack 2
Swing film guide (There are 4 types.) 1 each
Drive gear 1
Idle gear 1
Bushing 2
Wiring angle bracket 1
Leader card 10
Splicing tape 1
Vinyl hose 1
Washing bottle (500 ml) 1
Rag 1
Slow-blow fuse (3.15A) 5
Slow-blow fuse (6.3A) 5
Slow-blow fuse (10A) 5
Nylon cable ground 1
Oil (35 ml) 1
Splicing gauge unit 1
Magazine (control strip) 1
Maintenance tool 1
O-ring 1
Wiring angle bracket 1
Nylon cable ground 1
Magazine adaptor 1
Stick 1
Check date entry sticker 1
10
Options
Option No. Item Description / Explanation
Z803957-01 Rewinding box Used as a light-tight box into which film
(120,126 or 110) is taken out of its
original cassette and is wound up.
Z800016-01 Tape cutting gauge Used to cut splicing tape into preset
lengths.
A510260-01 Leader card Used to pull film through the processor.
Z890021-01 Check label dispenser Used to dispense labels to distinguish
different orders.
A662421-01 Splicing tape Used to splice leader cards to film.
A108695-01 Splicing tape (110)
A233402-01 Anti-contamination cover Used to prevent auxiliary solutions from
dripping into the CD solution when
removing processing racks, etc.
Z806851-01 Rack transportation tank Used to transport a processing rack
removed from the processing tanks to
prevent solution from dripping on the
floor.
Z803969-01 Floor tray Placed underneath the machine to
protect the floor.
H069139-00 Tape dispenser Used to supply splicing tape at a preset
length.
C101570-01 Turn rack vat Used when washing or soaking the turn
guide racks.
H029042-00 Filter cartridge Used to remove foreign substances from
solutions during operations.
Z801662-01 Magazine (110) Used when processing 110 film.
Z016846-01 Magazine (126) Used when processing 126 film.
A509002-01 Brush Used to wash the tanks. Its long handle
makes it possible to clean even the
bottom of the processing tanks.
H059028-00 Manual film leader extractor Used to manually extract the film tongue
from a cassette.
Z800008-01 Magazine (120) Used when processing 120 and 220
films.
Z806854-01 Digital flowmeter Used to measure the CD flow in the film
processor. Result is then shown on the
display.
A202513-01 Filler Graduated pitcher, 5 liter
L005112-00 Thermometer Mercury thermometer used to measure
solution temperatures.
L005253-00 Measuring cylinder (200 ml) Used to measure chemicals, etc.
Z810340-01 System service kit One set of spares for parts subject to
Z806952-01 Spare parts kit wear.
11
Option No. Item Description / Explanation
H069025-00 Check label (blue) Used to make it easy to return film to the
H069026-00 Check label (green) proper DP bag.
H069027-00 Check label (black)
H069028-00 Check label (red)
H069029-00 Check label (brown)
H069030-00 Check label (yellow)
Z806845-01 Cooling water unit Used to cool off processing solutions.
This unit is necessary when the chilling
unit is connected.
Z806846-01 Cooling water unit Used to cool off processing solutions.
This unit is necessary when the chilling
unit is not connected.
D203838-00 Emergency dark bag Used to cover the loading box if necessary.
Z810327-01 DP bag holder Holder used to put the DP bag in.
Z810333-01 Bar-code reader attaching kit. One kit for attaching the bar-code reader
to the splice gauge.
Z806868-01 Waste solution concentrator connecting kit This connecting kit is to be used to
(for individual waste solution collecting unit) connect the maste solution concentrator
to the film processor.
Z806870-01 Waste solution concentrator connecting kit This connecting kit is to be used to connect
(for individual waste solution collecting unit) the maste solution concentrator to the printer
processor.
B105882-01 Magazine adapter Used when developing 110 film.
Z810334-01 40 liter separate replenisher tanks Used to store replenisher solutions
(for 4 solutions) separately from the film processor.
Z810335-01 40 liter separate replenisher tanks
(for 5 solutions)
B210180-01 Leader card (IX240) Used to pull IX240 film through the film
B011437-01 Leader card, red (IX240) processor.
Z807181-01 Intermediate cartridge Used when developing film cartridge.
Z810353-01 Splicing gauge modification kit Parts needed to splice IX240 film with the
Z810354-01 Splicing gauge 2 modification kit present splicing gauges.
Z810329-01 Splicing gauge (IX240) Splicing gauge for splicing film (IX240
and others) to leader cards.
Z807148-01 Film processor modification parts Used to modify the film loading box to
develop IX240 film.
Z023440-01 Splicing gauge with bar-code reader Splicing gauge with the equipment
reading the bar-code on the film
cartridge of 135 film.
12
Note
・ Machines are to be used in a place where the relative humidity is from 30% to 75% and the temperature
is from 18 ℃ to 30 ℃ (64˚F to 86˚F).
・ The light which illuminates this machine should be the color of natural light and limited to 300 to 400 lux.
Direct light near this machine should be screened. A curtain or blind should be provided to keep sunlight
away from the equipment when necessary.
・ Do not install the machine in a place that is very dusty or where a lot of vibration is present.
・ The customer is requested to prepare the plumbing between the processor, drain, and cooling water
valve.
・ Connect the drain with reinforced PVC pipe and connect the cooling water supply valves with steel pipe or
reinforced PVC pipe.
・ Be sure to install a strainer (80 or 100 mesh) between the cooling water shut off valve and solenoid valve.
・ Do not raise the room temperature suddenly. If you do so, moisture in the air is likely to condense on the
machine, causing film jams, malfunctions in the electronics and PCBs, etc.
・ Although this machine is of waterless specification, it uses solution. Therefore, for the sake of safety,
please make the floor and walls waterproof. In addition, please install a drain in the room to facilitate
washing racks.
・ The castors on the bottom of the machine are for moving the machine a short distance, only. Once the
machine has been positioned, be sure to fix it in place with the jack bolts.
・ If each position of jack bolt on the floor is not uneven (difference: 15 mm or more), place a plate or the like
under the jack bolt to level the machine.
・ When the separate replenisher tank (option) is used, place it so that the solution level that the replenisher
poured upto the regular amount is lower than the replenisher outlet.
・ The standard value has been previously set to each mode in shipment for the machine. It may differ
depending on the ambient conditions. Change the value if necessary.
13