Professional Documents
Culture Documents
AquaArm PowerPrufe 900
AquaArm PowerPrufe 900
Product Description
AquaArm Power Prufe 900 is a 3 layer pre pre-applied HDPE Membrane, composed of one thick HDPE backing layer, an
aggressive pressure sensitive adhesive and trafficable weather resistant protective granular coating.
coating AquaArm Power
Prufe 900 provides a firm bonding to poured concrete, which prevents water ingress or migration.
Uses
Ver/5/PN/Oct 2019 1 of 4
W ATERPROOFING
Application Methodology
Step No 1: Substrate Preparation: Fastening through the selvedge using a small and
low profile head fastener so that membrane lays
Substrate must be smooth, sound and no voids or gaps flat and allows firmly rolled overlaps.
more than 10mm. Proper filling with self
self-flowing grout Ensure the underside of the succeeding sheet is
recommended around all penetrations for stability. clean, dry and free from contamination before
attempting to overlap.
Horizontal surface- PCC / monolithic concrete binding is
preferred. Angular profile is recommended. Remove all Roll firmly to ensure a watertight
watertigh seal.
protrusions and clean up the substrate. There should not Overlap all roll ends and cut edges by a minimum
be any standing water on surface during application. 75 mm and ensure the area is clean and free from
contamination, wiping with a damp cloth if
Step No 2 :Membrane Installation:
necessary.
Horizontal surface Allow to dry and apply AquaArm PowerPrufe
800centered over the lap edges and roll firmly.
Place the membrane HDPE film side to the
substrate with granular layer facing towards the Penetration sealing- Grout around penetration to hold
concrete pour. End laps should be staggered to tight to the penetration and seal around pipe with
avoid a build-up of layers. PowerPrufe
rufe DST Tape and WPU liquid PU membrane.
Accurately position succeeding sheets to overlap
the previous sheet 75 mm along the marked Pile Head Sealing – Prepare a smooth Pile head with
selvedge. Ensure the underside of the succeeding Non-Shrink
Shrink cementitious grout. Once grout dried up
sheet is clean, dry and free from contamination fully,
y, seal top of pile head with ArmGrout EP78 up to 8-
before attempting to overlap. 10mm thickness.
Ver/5/PN/Oct 2019 2 of 4
W ATERPROOFING
Formwork Removal
Peel Adhesion to
ASTM D 903 N/M 880+100
concrete AquaArm PowerPrufe 900 00 membrane can be applied to
removable
vable shuttering, such as slab perimeters, lift pits,
Low temperature 0 etc. Once the concrete is poured the formwork must
ASTM D1970 Deg C -25 C
flexibility remain in place until the concrete has gained sufficient
compressive strength to develop the surface bond.
AquaArm PowerPrufe 900 00 is not recommended for twin
Dimension
Stability
ASTM D 1204 % <1 sided wall shutters.
Width :1M&2M
Length : 20M
Available in 1.5mm thickness
Ver/5/PN/Oct 2019 3 of 4
W ATERPROOFING
Legal Note
The information, and, in particular, the recommendations relating to the application and endend-use
use of MYK Arment products, are given in
good faith based on MYK Arment current knowledge and experience of the products when properly stored, handled and applied under
normal conditions in accordance with MYK Arment’s recommendations. In practice, the difference in materials, substrates and a actual
site conditions are such that no warranty in respect of merchant ability or of fitness for a particular purpose, nor any liability arising out
of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, or ffrom any
other advice offered. the user of the product must test the product's suitability for the intended application & purpose. MYK Arment
reserves the right to change the properties of its products. the proprietary rights of third parties must be observed. All or orders are
accepted subject to our current terms of sale and delivery. Users must always refer to the most recent issue of the local product data
sheet for the product concerned, copies of which will be supplied on request.
Ver/5/PN/Oct 2019 4 of 4