Professional Documents
Culture Documents
Detail 8_Weld S275
Detail 8_Weld S275
Material
Steel S 355
Concrete C25/30, C32/40
Design
Name Detail 8
Description Inclined
Analysis Stress, strain/ simplified loading
Members
Geometry
X
Name Support Forces in
[mm]
M1 / end Node 0
1 / 12
Project: Detail - 8
Project no: CR202
Author: SK
Cross-sections
Name Material
1 - UC 356 x 406 x 634 S 355
6 - Iw600x600 S 355
Cross-sections
Name Material Drawing
6 - Iw600x600 S 355
Anchors
Diameter fy fu Gross area
Name
[mm] [MPa] [MPa] [mm2]
M36 Rebar 36 500.0 650.0 1018
2 / 12
Project: Detail - 8
Project no: CR202
Author: SK
Foundation block
Item Value Unit
CB 1
Dimensions 10046 x 17425 mm
Depth 2000 mm
Anchor M36 Rebar
Anchoring length 700 mm
Shear force transfer Shear lug
Cross-section of shear lug Iw600x600
Length of shear lug 800 mm
Mortar joint 50 mm
Check
Summary
Name Value Check status
Analysis 100.0% OK
Plates 0.1 < 5.0% OK
Anchors 80.3 < 100% OK
Welds 77.6 < 100% OK
Concrete block 7.2 < 100% OK
Shear 85.0 < 100% OK
Buckling Not calculated
Plates
tp σEd εPl σc,Ed
Name Material Loads Status
[mm] [MPa] [%] [MPa]
M1-bfl 1 S 355 77.0 LE1 127.6 0.0 0.0 OK
M1-tfl 1 S 355 77.0 LE1 169.8 0.0 0.0 OK
M1-w 1 S 355 47.6 LE1 140.1 0.0 0.0 OK
Member 2-tfl 1 S 355 50.0 LE1 335.2 0.1 0.0 OK
Member 2-bfl 1 S 355 50.0 LE1 335.0 0.0 0.0 OK
Member 2-w 1 S 355 50.0 LE1 256.1 0.0 0.0 OK
SP1 S 355 60.0 LE1 307.2 0.0 0.0 OK
WID2a S 355 - 1 25.0 LE1 132.3 0.0 0.0 OK
WID2b S 355 - 1 25.0 LE1 132.4 0.0 0.0 OK
WID2c S 355 - 1 25.0 LE1 219.2 0.0 0.0 OK
WID2d S 355 - 1 25.0 LE1 279.6 0.0 0.0 OK
RIB1a S 355 - 1 25.0 LE1 352.7 0.0 0.0 OK
RIB1b S 355 - 1 25.0 LE1 353.1 0.0 0.0 OK
3 / 12
Project: Detail - 8
Project no: CR202
Author: SK
Design data
fy εlim
Material
[MPa] [%]
S 355 335.0 5.0
S 355 - 1 355.0 5.0
γM 0
Where:
fyk = 335.0 MPa – characteristic yield strength
4 / 12
Project: Detail - 8
Project no: CR202
Author: SK
5 / 12
Project: Detail - 8
Project no: CR202
Author: SK
Design data
NRd,s
Grade
[kN]
M36 Rebar - 1 289.4
Following checks of anchors loaded in tension are not provided and should be checked using information in relevant European
Combined pull-out and concrete failure (for post-installed bonded anchors) - EN 1992-4 – 7.2.1.6
Concrete blow-out failure is provided only for anchors with washer plates.
6 / 12
Project: Detail - 8
Project no: CR202
Author: SK
γM s
= 289.4 kN ≥ NEd =
232.2 kN
NRk,s = c ⋅ As ⋅ fuk =
451.4 kN
Where:
c = 0.85 – reduction factor for cut thread
As =
817 mm2 – tensile stress area
γM s = 1.56
– safety factor for steel
γM s = 1.2 ⋅ ffuk
yk
≥ 1.4 , where:
Interaction of tensile and shear forces in steel (EN 1992-4 – Table 7.3)
2 2
( NNRd,s
Ed
) + ( VVRd,s
Ed
) =
0.64 ≤ 1.0
Where:
NEd = 232.2 kN – design tension force
Interaction of tensile and shear forces in concrete (EN 1992-4 – Table 7.3)
Ed 1.5 Ed 1.5
( NNRd,i
) + ( VVRd,i
) =
0.00 ≤ 1.0
Where:
NEd
– the largest utilization value for tension failure modes
NRd,i
VEd
– the largest utilization value for shear failure modes
VRd,i
NEd,g
= 0% – concrete breakout failure of anchor in tension
NRd,c
NEd
NRd,p
= 0% – concrete pullout failure
NEd
NRd,cb
= 0% – concrete blowout failure
VEd
VRd,c
= 0% – concrete edge failure
VEd
VRd,cb
= 0% – concrete pryout failure
7 / 12
Project: Detail - 8
Project no: CR202
Author: SK
Welds
Tw L σw,Ed εPl σ⏊ τ⏊ τ|| Ut Utc
Item Edge Loads Detailing Status
[mm] [mm] [MPa] [%] [MPa] [MPa] [MPa] [%] [%]
◢ 30.0
SP1 M1-bfl 1 423 LE1 91.6 0.0 39.0 42.9 -21.2 22.6 22.6 OK OK
◣
◢ 30.0
423 LE1 187.6 0.0 -25.5 -104.2 25.6 46.4 44.9 OK OK
◣
◢ 30.0
SP1 M1-tfl 1 423 LE1 142.4 0.0 -23.8 -61.3 53.0 35.2 27.0 OK OK
◣
◢ 30.0
423 LE1 120.4 0.0 -49.6 62.8 -7.9 29.7 21.2 OK OK
◣
◢ 30.0
SP1 M1-w 1 685 LE1 184.3 0.0 92.0 92.0 6.6 45.5 24.2 OK OK
◣
◢ 30.0
685 LE1 184.5 0.0 92.0 -92.0 -6.8 45.6 23.4 OK OK
◣
Member 2-tfl ◢ 30.0
SP1 599 LE1 314.1 0.0 -171.4 -121.2 -91.6 77.6 69.2 OK OK
1 ◣
◢ 30.0
599 LE1 159.8 0.0 -11.3 61.4 68.5 39.5 35.7 OK OK
◣
Member 2-bfl ◢ 30.0
SP1 599 LE1 223.4 0.0 38.3 124.9 23.8 55.2 30.7 OK OK
1 ◣
◢ 30.0
599 LE1 233.4 0.0 175.1 -88.6 9.3 57.7 40.3 OK OK
◣
Member 2-w ◢ 30.0
SP1 499 LE1 128.7 0.0 18.3 18.3 71.2 31.8 17.9 OK OK
1 ◣
◢ 30.0
499 LE1 128.4 0.0 18.2 -18.2 -71.1 31.7 17.0 OK OK
◣
◢ 20.0
SP1 WID2a 399 LE1 75.1 0.0 30.1 21.2 -33.6 18.5 13.6 OK OK
◣
◢ 20.0
399 LE1 205.3 0.0 -3.3 -97.9 -66.9 50.7 36.8 OK OK
◣
M1-bfl
WID2a - 450 - - - - - - - - OK OK
1
◢ 20.0
SP1 WID2b 399 LE1 198.2 0.0 -5.0 96.6 61.4 49.0 34.7 OK OK
◣
◢ 20.0
399 LE1 72.2 0.0 30.1 -21.7 31.0 17.8 13.2 OK OK
◣
M1-bfl
WID2b - 450 - - - - - - - - OK OK
1
◢ 20.0
SP1 WID2c 398 LE1 131.5 0.0 47.1 38.2 -59.7 32.5 25.0 OK OK
◣
◢ 20.0
399 LE1 313.0 0.0 1.8 -180.6 5.0 77.3 55.8 OK OK
◣
M1-tfl 1 WID2c - 450 - - - - - - - - OK OK
◢ 20.0
SP1 WID2d 398 LE1 311.3 0.0 -5.2 175.8 -37.3 76.9 51.3 OK OK
◣
◢ 20.0
398 LE1 136.3 0.0 -0.6 22.1 75.5 33.7 22.2 OK OK
◣
M1-tfl 1 WID2d - 450 - - - - - - - - OK OK
8 / 12
Project: Detail - 8
Project no: CR202
Author: SK
Design data
fu βw σw,Rd 0.9 σ
Material
[MPa] [-] [MPa] [MPa]
S 275 430.0 0.85 404.7 309.6
⊥ ∥
314.1 MPa
σ⊥,Rd = 0.9 fu / γM 2 =
309.6 MPa ≥ ∣σ⊥ ∣ =
174.0 MPa
where:
fu = 430.0 MPa – Ultimate strength
βw = 0.85
– Correlation factor EN 1993-1-8 – Tab. 4.1
Stress utilization
σ ∣σ⊥ ∣
Ut = max( σw,Ed ; ) = 0.78 ≤ 1.0
w,Rd
σ⊥,Rd
Where:
σw,Ed = 314.1 MPa – Maximum normal stress transverse to the axis of the weld
σ⊥ = -174.0 MPa
– Normal stress perpendicular to the throat
c Aeff σ kj fjd Ut
Item Loads Status
[mm] [mm2] [MPa] [-] [MPa] [%]
9 / 12
Project: Detail - 8
Project no: CR202
Author: SK
fjd =
42.9 MPa ≥ σ= 3.1 MPa
Where:
fjd – concrete block design bearing strength:
σ= N
Aef f
, where:
N = 849.3 kN – compressive normal force acting on concrete block
Aef f = 276524 mm2 – effective area on which normal force is distributed
5124.0 kN
Where:
Avy = 60000 mm2 – shear area Ay of shear lug cross-section
fy = 355.0 MPa
– anchor yield strength
γM 0 = 1.00
– safety factor
10 / 12
Project: Detail - 8
Project no: CR202
Author: SK
Vc,Rd = AσRd,max =
8371.3 kN
Where:
A = lb = 450005 mm2 – projected area of the shear lug excluding the portion above concrete
l = 750 mm – length of the shear lug excluding the portion above concrete
b = 600 mm – projected width of the shear lug in the direction of shear load
σRd,max = k1 v′ f
ck /γc
= 18.6 MPa – maximum stress which can be applied at the edges of the node
k1 = 1.00
– factor - EN 1992-1-1 - Equation (6.60)
γc = 1.50
– safety factor
Utilization in shear
V
Ut = max( VRd,y
y
, VVRd,z
z
, VVcRd ) = 0.85 ≤ 1
Buckling
Buckling analysis was not calculated.
11 / 12
Project: Detail - 8
Project no: CR202
Author: SK
Code settings
Item Value Unit Reference
Safety factor γM0 1.00 - EN 1993-1-1: 6.1
Safety factor γM1 1.00 - EN 1993-1-1: 6.1
Safety factor γM2 1.25 - EN 1993-1-1: 6.1
Safety factor γM3 1.25 - EN 1993-1-8: 2.2
Safety factor γC 1.50 - EN 1992-1-1: 2.4.2.4
Safety factor γInst 1.20 - EN 1992-4: Table 4.1
Joint coefficient βj 0.67 - EN 1993-1-8: 6.2.5
Effective area - influence of mesh size 0.10 -
Friction coefficient - concrete 0.25 - EN 1993-1-8
Friction coefficient in slip-resistance 0.30 - EN 1993-1-8 tab 3.7
Limit plastic strain 0.05 - EN 1993-1-5
Detailing Yes
Distance between bolts [d] 2.20 - EN 1993-1-8: tab 3.3
Distance between bolts and edge [d] 1.20 - EN 1993-1-8: tab 3.3
Concrete breakout resistance check None EN 1992-4: 7.2.1.4 and 7.2.2.5
Use calculated αb in bearing check. Yes EN 1993-1-8: tab 3.4
Cracked concrete Yes EN 1992-4
Local deformation check Yes CIDECT DG 1, 3 - 1.1
Local deformation limit 0.03 - CIDECT DG 1, 3 - 1.1
Geometrical nonlinearity (GMNA) Yes Analysis with large deformations for hollow section joints
Braced system No EN 1993-1-8: 5.2.2.5
12 / 12