Professional Documents
Culture Documents
Imprimante Balance Epson Tm u295 Bw Dotmatrix Printer
Imprimante Balance Epson Tm u295 Bw Dotmatrix Printer
Operator’s Manual
Use the scroll bar next to the bookmarks to find any topic you
want. Click a bookmark to instantly jump to its topic. (If you wish,
you can increase the size of the bookmark area by dragging the
dividing bar to the right.)
Use the scroll bar on the right side of this screen to move through
the text.
Use the zoom tools to magnify or reduce the page display.
Click the Find button if you want to search for a particular term.
(However, using the bookmarks is usually quicker.)
Complete online documentation for Acrobat Reader is located in the Help directory for Acrobat Reader.
400483605
(1)
(2)
(5)
(4)
(10)
(6) (10)
(7) (8) (9) (6)
(7) (8) (9)
TM-U295 TM-U295P
NOTICE: The contents of this manual are subject to change without notice.
WARNING
The connection of a non-shielded printer interface cable to this printer will invalidate
the FCC Verification of this device and may cause interference levels which exceed
the limits established by the FCC for this equipment.
You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to operate the
equipment.
GEREÄUSCHPEGEL
Gemäß der Dritten Verordrung zum Gerätesicherheitsgecsetz
(Maschinenlärminformations- Verordnung-3. GSGV) ist der arbeitsplatzbezogene
Geräusch-Emissionswert kleiner als 70 dB(A) (basierend auf ISO 7779).
ii
iii
iv
❏ Character directions: 4
❏ International character set selection
❏ Forward and backward paper feeding
❏ Command protocol based on ESC/POS®, a widely used standard
❏ Programmable paper feed amount
❏ Paper eject function
❏ Top Of Form (TOF) and Bottom Of Form (BOF) sensors
❏ Data reception during printing (improved throughput and less waiting time for
the host computer)
* In page mode, the print data for each page is stored in a specified printing
area in memory. After all the data for a page has been stored, it is printed.
Please be sure to read the instructions in this manual carefully before using your new
EPSON printer.
Reference
❏ Chapter 4 contains specifications
CAUTION:
Cautions must be observed to avoid minor injury to yourself or
damage to your equipment.
WARNING:
Warnings must be followed carefully to avoid serious bodily
injury.
vi
Chapter 1 Installation
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Removing the Transportation Damper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Connecting the Printer to the Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
TM-U295 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
TM-U295P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Connecting the Printer to the Drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Grounding the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Connecting the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Installing the Ribbon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Inserting Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
Running the Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Setting the DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
TM-U295 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16
TM-U295P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17
Chapter 3 Troubleshooting
Power problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Printing problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
vii
viii
Unpacking
When you unpack the TM-U295 or TM-U295P printer, make sure
you have these items.
Damper
Ribbon cassette
Note:
See the Note on page 1-3 for information about the screws.
Installation 1-1
1. Pull the damper out and remove the strip of tape from the top
of the printer, as shown below.
Note:
If you ever ship or store your printer, prepare it by performing these
steps: turn on the printer, press the RELEASE button, press the
FORWARD button, turn off the printer, and put the transportation
damper back where it was when you received the printer.
1-2 Installation
1. Make sure that the printer and the computer are turned off.
Then plug the cable into the connector on the back of the
printer, as shown.
Note:
Your printer comes with inch-type hexagonal lock screws installed.
If you plan to use an interface cable that requires millimeter-type
lock screws, replace the inch-type screws with the enclosed
millimeter-type screws by using a hex screwdriver (5 mm). To
distinguish the two types of screws, see the illustration below; the
screw on the right is the millimeter type.
Installation 1-3
TM-U295P
You need an appropriate parallel interface cable to connect your
computer to the printer.
1. Make sure that the printer and the computer are turned off.
Then plug the cable into the connector on the back of the
printer, as shown.
Note:
Squeeze the wire clips on the printer together until they lock in place
on both sides of the connector.
1-4 Installation
TM-U295
TM-U295P
CAUTION:
Do not connect a telephone line to the drawer kick out
connector.
Installation 1-5
TM-U295
TM-U295P
CAUTION:
Kein Telefonkabel an die Schnappsteckerbuchse
anschließen.
1-6 Installation
TM-U295
TM-U295P
Installation 1-7
CAUTION:
Using an incorrect power supply can cause serious damage
to the printer.
TM-U295
TM-U295P
1-8 Installation
Note:
For instructions on replacing a used ribbon, see Chapter 2.
1. Turn the printer on using the power switch on its left side.
2. Press the RELEASE button to turn the light on. This puts the
printer in the paper release mode.
Installation 1-9
1-10 Installation
7. Then push firmly on the right side and then the left side of the
ribbon cartridge until each side clicks into place.
Installation 1-11
Inserting Paper
Note:
Do not use wrinkled or curled paper. For full information and
specifications on the paper you can use, see Chapter 4.
3. Press the RELEASE button. The RELEASE light comes on, which
indicates that the printer is in the paper release mode. In this
mode, the printer can accept paper and paper can be removed
from it.
1-12 Installation
5. Check the PAPER OUT light. When you insert the paper
correctly, the PAPER OUT light goes out. If the PAPER OUT light
is still on, remove the paper and re-insert it.
The self test checks the control circuits, printer mechanisms, print
quality, RAM, ROM version, and DIP switch settings.
Installation 1-13
***completed***
The printer ejects the paper; then enters the normal mode.
1-14 Installation
Installation 1-15
7
See Transmission Speeds table below.
8
Transmission Speeds
Speed in Bits per Second SW 7 SW 8
1200 ON ON
2400 OFF ON
4800 ON OFF
1-16 Installation
Normally Normally
1 Auto-line feed
enabled disabled
3 Undefined
4 Undefined
5 Undefined
6 Undefined
7 Undefined
8 Undefined
9 Undefined
Note:
If you change any DIP switch settings while the printer is turned
on, the new settings will not take effect until you turn the printer off
and back on or reset it.
Installation 1-17
Buttons
All three of these buttons can be disabled or enabled by the ESC c 5
command.
RELEASE
Pressing this button moves the rollers so that paper can be inserted
or removed.
REVERSE
Feeds the paper backward based on the line feed amount set by
ESC 2 and ESC 3.
FORWARD
Feeds the paper forward based on the line feed amount set by
ESC 2 and ESC 3.
You can also use the RELEASE button to start a self test.
See Chapter 1 for details.
Indicator Lights
POWER
This light is on whenever power is supplied to the printer.
❏ Paper jam
❏ Timing error
If this light blinks, turn off the printer, make sure that no paper is
jammed in it, and then turn it back on. If the light is still blinking,
contact a qualified service person.
PAPER OUT
This light is on when paper is not inserted or is not inserted
correctly.
Power problems
Make sure that the power supply cables are correctly plugged into
the printer, the power unit, and to the power outlet.
Make sure that power is supplied to the power outlet. If the outlet
is controlled by a switch or timer, use another outlet.
Printing problems
If the PAPER OUT light is on, the paper is not inserted or is not
inserted correctly.
This indicates an error condition. Turn off the printer, make sure
that no paper is jammed in it, and then turn it back on. If the
RELEASE light is still flashing, contact a qualified service person.
Troubleshooting 3-1
Printing Specifications
Printing Method: Impact dot matrix
Character Specifications
Number of Alphanumeric characters: 95
characters Extended graphics: 128 x 3
International characters: 32
Combina- 3 sheets
tion of maximum (1
normal original and 2
paper and copies) (0.09 to
pressure 0.35 mm (.0035 to
sensitive .0138”))
paper:
Backing paper:
0.07 to 0.20 mm
(.0028 to .0079”)
Copy and original
paper:
0.04 to 0.07 mm
(.0016 to .0028”)
Carbon copy
paper:
Approximately
0.035 mm (.0014”)
❏ Glue area should be located at the top or left edge of the slip
paper.
❏ Since TOF and BOF sensors are optical sensors, paper having
holes at the sensor positions or translucent paper should not be
used normallly. When using these papers, be sure to disable the
paper sensors by ESC c 4.
2.3 (.09")
10 (.39")
NOTE 2. TOF sensor (fixed)
Adjustable
26.5 (1.04")
Printing position at minimum top margin
Reverse paper feed
Forward paper feed
27.3 (1.07")
NOTE 2. BOF sensor (fixed) 12.5 (.49")
Notes
1. The mechanical form stopper is adjustable in the range 26.5 to
36.5 mm (1.04 to 1.44”).
2. The TOF and BOF sensors are fixed and cannot be adjusted.
3. After slip paper is set at the mechanical form stopper, the top
margin can be shortened up to 21.2 mm (.83”) by feeding the
paper backwards (ejection feeding).
Peak - approx.
5.5 A at 24 VDC
(full-column
printing and data
transmission of
ANK characters)
Standby: approx.
100 mA (at 24
VDC, 25°C (77°F)
Reliability
Life: 3,000,000 lines
Interface Specifications
Serial interface: RS-232 compatible
Note:
The interface is a factory installed option. One of the interfaces
(serial or parallel) is already installed.
Note:
Refer to the EPSON TM-U295/U295P Specification for details.
Command Notation
[Name] The name of the command.
[Format] The code sequence.
ASCII indicates the ASCII equivalents.
Hex indicates the hexadecimal equivalents.
Decimal indicates the decimal equivalents.
[ ]k indicates the contents of the [ ] should be repeated k times.
[Range] Gives the allowable ranges for the arguments.
[Description] Describes the function of the command.
[Notes] Provides important information on setting and using the printer
command, if necessary.
[Default] Gives the default values, if any, for the command parameters.
[Reference] Lists related commands.
[Example] Provides examples using the command.
Commands 5-1
LF
[Name] Print and line feed
[Format] ASCII LF
Hex 0A
Decimal 10
[Description] Prints the data in the print buffer and feeds one line based on the
current line spacing.
[Note] This command sets the print position to the beginning of the line.
[Reference] ESC 2, ESC 3
FF
[Name] ➀Print and eject sheet (in standard mode)
➁Print and return to standard mode (in page mode)
[Format] ASCII FF
Hex 0C
Decimal 12
This command functions differently depending on the printer mode selected.
➀When standard mode is selected:
[Description] Prints the data in print buffer and ejects the sheet.
[Notes] • When the eject length has been set by ESC C, the printer ejects the
sheet based on the current eject length. Otherwise, the printer
ejects the sheet completely. If a paper out is detected during
ejection, the printer stops ejecting the sheet even if the specified
amount of paper has not been ejected.
• The ejecting direction is specified by ESC F.
[Reference] ESC F, ESC C
➁When page mode is selected:
5-2 Commands
CR
[Name] Print and carriage return
[Format] ASCII CR
Hex 0D
Decimal 13
[Description] When auto-line feed is enabled, this command functions in the same
way as LF. When auto-line feed is disabled, this command is ignored.
[Notes] • This command sets the print position to the beginning of the line.
• This command is available only with a parallel interface and is
ignored with a serial interface.
DLE EOT n
[Name] Real-time status transmission
[Format] ASCII DLE EOT n
Hex 10 04 n
Decimal 16 4 n
[Range] 1≤ n ≤ 3, n = 5
[Description] Transmits the selected printer status specified by n in real time,
according to the following parameters:
n = 1: Transmit printer status
n = 2: Transmit off-line status
n = 3: Transmit error status
n = 5: Transmit slip paper status
[Notes] • The printer executes this command upon receiving it.
• When transmitting status, the printer transmits only 1 byte
without confirming the condition of the DSR signal.
• With the serial interface model, this command is executed even in
off-line or receive buffer-full state. However, with the parallel
interface model, this command is not executed in off-line or
receive buffer-full state because the printer is busy and unable to
receive this command from the host.
• The status is transmitted whenever the data sequence of
<10>H<04>H<n> (1 ≤ n ≤ 3, n = 5) is received even if it appears as
part of another command. For example,
In ESC ✻ m n L n H [d] n L+256✕n H, d1=<10>H, d2=<04>H,
d3=<1>H
Commands 5-3
Off 00 0 On-line.
3
On 08 8 Off-line.
Off 00 0 Undefined.
5
On 20 32 Undefined.
Off 00 0 Undefined.
6
On 40 64 Undefined.
n = 2: Off-line status
Off 00 0 Undefined.
2
On 04 4 Undefined.
5-4 Commands
Off 00 0 No error.
6
On 40 64 Error occurs.
Off 00 0 Undefined.
2
On 04 4 Undefined.
Off 00 0 Undefined.
3
On 08 8 Undefined.
Off 00 0 Undefined.
6
On 40 64 Undefined.
Commands 5-5
Bit 3: Becomes Off (not waiting) just before actual slip selection takes place
after slip paper is detected
Bit 5 and 6: Transmits the current status of the TOF and BOF sensors.
[Reference] ESC u, ESC v, GS a
CAN
[Name] Cancel print data in page mode
[Format] ASCII CAN
Hex 18
Decimal 24
[Description] In page mode, deletes all the print data in the current printable area.
[Notes] • This command is enabled only in page mode.
• If data that existed in the previously specified printable area also
exists in the currently specified printable area, it is deleted.
[Reference] ESC W
ESC SP n
[Name] Set right-side character spacing
[Format] ASCII ESC SP n
Hex 1B 20 n
Decimal 27 32 n
[Range] 0 ≤ n ≤ 32
5-6 Commands
ESC ! n
[Name] Select print mode(s)
[Format] ASCII ESC ! n
Hex 1B 21 n
Decimal 27 33 n
[Range] 0 ≤ n ≤ 255
[Description] Selects print mode(s) using n as follows:
Off 00 0 Undefined.
1
On 02 2 Undefined.
Off 00 0 Undefined
2
On 04 4 Undefined.
Off 00 0 Undefined.
3
On 08 8 Undefined.
Off 00 0 Undefined.
6
On 40 64 Undefined.
Commands 5-7
ESC % n
[Name] Select/cancel user-defined character set
[Format] ASCII ESC % n
Hex 1B 25 n
Decimal 27 37 n
[Range] 0 ≤ n ≤ 255
[Description] Selects or cancels the user-defined character set.
When the Least Significant Bit (LSB) is 0, the user-defined character
set is cancelled.
When the LSB is 1, the user-defined character set is selected.
[Notes] • When the user-defined character set is cancelled, the internal
character set is automatically selected.
[Default] n=0
[Reference] ESC &
5-8 Commands
p1 p2 p3 p4 p5 p6
MSB
LSB
Commands 5-9
p1 p2 p3 p4 p5 p6 p7 p8 p9 p10
MSB
LSB
5-10 Commands
Commands 5-11
7 6 5 4 3 2 1 0
Print data
Top
Bottom
Bit image data
ESC 2
[Name] Select 1/6-inch line spacing
[Format] ASCII ESC 2
Hex 1B 32
Decimal 27 50
[Description] Selects 1/6-inch line spacing.
[Note] The line spacing can be set independently in standard mode and in
page mode.
[Reference] ESC 3
ESC 3 n
[Name] Set line spacing
[Format] ASCII ESC 3 n
Hex 1B 33 n
Decimal 27 51 n
[Range] 0 ≤ n ≤ 255
[Description] Sets the line spacing to n/60 inches.
[Notes] • This command sets values independently in standard mode and
in page mode.
[Default] n = 10 (1/6 inch)
[Reference] ESC 2
ESC = n
[Name] Set device
[Format] ASCII ESC = n
5-12 Commands
Off 00 0 Undefined.
1
On 02 2 Undefined.
Off 00 0 Undefined.
2
On 04 4 Undefined.
Off 00 0 Undefined.
3
On 08 8 Undefined.
Off 00 0 Undefined.
4
On 10 16 Undefined.
Off 00 0 Undefined.
5
On 20 32 Undefined.
Off 00 0 Undefined.
6
On 40 64 Undefined.
Off 00 0 Undefined.
7
On 80 128 Undefined.
[Notes] • When the printer is not selected, the printer ignores all received
data until it is selected by this command.
• Even if the printer is disabled, it may go off-line due to printer
operation.
[Default] n=1
ESC @
[Name] Initialize printer
[Format] ASCII ESC @
Hex 1B 40
Decimal 27 64
[Description] Clears the data in the print buffer and resets the printer mode to the
mode that was in effect when the power was turned on.
Commands 5-13
ESC C n
[Name] Set cut sheet eject length
[Format] ASCII ESC C n
Hex 1B 43 n
Decimal 27 67 n
[Range] 0 ≤ n ≤ 127
[Description] Sets the eject length for a cut sheet to n lines.
[Notes] • When n = 0, no eject length is set.
• The previously specified eject length does not change, even if the
line spacing changes.
• This command is available only when FF is executed.
[Default] n=0
[Reference] FF
5-14 Commands
ESC F n
[Name] Set/cancel cut sheet reverse eject
[Format] ASCII ESC F n
Hex 1B 46 n
Decimal 27 70 n
[Range] 0 ≤ n ≤ 255
[Description] Sets or cancels the cut sheet reverse eject specified by FF.
• When the LSB of n is 0, reverse eject is canceled and forwqrd eject
is set.
• When the LSB of n is 1, reverse eject is set.
[Note] When n cancels reverse eject, this command sets forward ejection
automatically.
[Default] n=0
[Reference] FF
ESC J n
[Name] Print and feed paper
[Format] ASCII ESC J n
Hex 1B 4A n
Decimal 27 74 n
[Range] 0 ≤ ≤ 255
n
[Description] Prints the data in the print buffer and feeds the paper by n/60
inches.
[Note] Sets the print position to the beginning of the line.
ESC K n
[Name] print and revers feed
Commands 5-15
ESC L
[Name] Select page mode
[Format] ASCII ESC L
Hex 1B 4C
Decimal 27 76
[Description] Switches from standard mode to page mode.
[Notes] • This command is enabled only when input at the beginning of a
line.
• This command is available only in standard mode.
• After printing by FF is completed, the printer returns to standard
mode.
• This command sets the position where data is buffered to the
position specified by ESC T within the printable area defined by
ESC W.
• In page mode, the printer buffer receives data in the printable area
specified by ESC W and prints the data collectively upon receipt
of FF command. The print and line feed commands, such as LF,
ESC J, ESC K, ESC d, and ESC e, only move the print start
position from which subsequent data is buffered and do not
perform actual printing.
• In page mode, the printer porcesses data referring to normal dot.
Therefore, be careful when using half dot in standard mode.
• Only character fonts with normal dot configuration are available.
• This command switches the settings for the following commands
(in which the values can be set independently in standard mode
and page mode) to those for page mode:
Set character spacing: ESC SP
Select 1/6-inch line spacing: ESC 2
Set line spacing: ESC 3
• In page mode, the following commands are ignored.
Print and reverse feed n lines: ESC e
Print and reverse feed: ESC K
5-16 Commands
ESC R n
[Name] Select an international character set
[Format] ASCII ESC R n
Hex 1B 52 n
Decimal 27 82 n
[Range] 0 ≤ n ≤ 10
[Description] Selects an international character set n from the following table:
n Character set
0 U.S.A.
1 France
2 Germany
3 U.K.
4 Denmark I
5 Sweden
6 Italy
7 Spain
8 Japan
9 Norway
10 Denmark II
Commands 5-17
Upper left
0, 48 Left to right
D
Lower left
1, 49 Bottom to top
(B in the figure)
Printing area
Lower right
2, 50 Right to left
(C in the figure) C
B
Upper right
3, 51 Top to bottom
(D in the figure)
[Notes] • When the printing direction is changed, the printing direction and
print starting position for the data following are those specified by
n.
• Only setting of this command is effective in standard mode.
• If n is out of the specified range, this command is ignored.
[Default] n=0
5-18 Commands
(x0, y0) dx
dy Printing area
(x0+dx-1,
y0+dy-1)
ESC c 3 n
[Name] Select paper sensor(s) to output paper end signals
[Format] ASCII ESC c 3 n
Commands 5-19
Off 00 0 Undefined.
0
On 01 1 Undefined.
Off 00 0 Undefined.
1
On 02 2 Undefined.
Off 00 0 Undefined.
2
On 04 4 Undefined.
Off 00 0 Undefined.
3
On 08 8 Undefined
Off 00 0 Undefined.
6
On 40 64 Undefined.
Off 00 0 Undefined.
7
On 80 128 Undefined.
ESC c 4 n
[Name] Select paper sensor(s) to stop printing
[Format] ASCII ESC c 4 n
Hex 1B 63 34 n
Decimal 27 99 52 n
5-20 Commands
Off 00 0 Undefined.
0
On 01 1 Undefined.
Off 00 0 Undefined.
1
On 02 2 Undefined.
Off 00 0 Undefined.
2
On 04 4 Undefined.
Off 00 0 Undefined.
3
On 08 8 Undefined.
Off 00 0 Undefined.
6
On 40 64 Undefined.
Off 00 0 Undefined.
7
On 80 128 Undefined.
ESC c 5 n
[Name] Enable/disable panel buttons
[Format] ASCII ESC c 5 n
Hex 1B 63 35 n
Commands 5-21
ESC d n
[Name] Print and feed n lines
[Format] ASCII ESC d n
Hex 1B 64 n
Decimal 27 100 n
[Range] 0 ≤ n ≤ 255
[Description] Prints the data in the print buffer and feeds n lines.
[Notes] • This command sets the print starting position to the beginning of
the line.
• This command does not affect the line spacing set by ESC 2 or
ESC 3.
[Reference] ESC 2, ESC 3
ESC e n
[Name] Print and reverse feed n lines
[Format] ASCII ESC e n
Hex 1B 65 n
Decimal 27 101 n
[Range] 0 ≤ n ≤ 255
[Description] Prints the data in the print buffer and feeds n lines in the reverse
direction.
[Notes] • The command is available only in standard mode.
• This command sets the print position to the beginning of the line.
• The setting values do not remain.
ESC f t1 t2
[Name] Set cut sheet wait time
[Format] ASCII ESC f t1 t2
Hex 1B 66 t1 t2
Decimal 27 102 t1 t2
[Range] t1 = 0
0 ≤ t2 ≤ 64
5-22 Commands
ESC p m t1 t2
[Name] Generate pulse
[Format] ASCII ESC p m t1 t2
Hex 1B 70 m t1 t2
Decimal 27 112 m t1 t2
[Range] m = 0, 1, 48, 49
0 ≤ t1 ≤ 255
0 ≤ t2 ≤ 255
[Description] Outputs the pulse specified by t1 and t2 to connector pin m as
follows:
m Connector pin
[Notes] • The pulse ON time is [t1 ✕ 2 ms] and the OFF time is [t2 ✕ 2 ms].
• If m is outside the specified range, the printer ignores this
command and the following data is processed as normal data.
ESC q
[Name] Paper release
[Format] ASCII ESC q
Hex 1B 71
Decimal 27 113
[Description] Releases the paper
[Notes] • This command is available only in standard mode.
• When the panel button is disabled and the specified paper sensor
detects a paper-end, the printer releases the paper, regardless of
this command.
Commands 5-23
ESC t n
[Name] Select character code table
[Format] ASCII ESC t n
Hex 1B 74 n
Decimal 27 116 n
[Range] 0≤n≤2
[Description] Selects a page n from the character code table.
n Page
1 1 (Katakana)
2 2 (PC850 [Multilingual])
[Note] If n is outside the specified range, the printer ignores this command.
[Default] n=0
ESC u n
[Name] Transmit peripheral device status
[Format] ASCII ESC u n
Hex 1B 75 n
Decimal 27 117 n
[Range] n = 0, 48
[Description] Transmits the status of connector pin n upon receiving this
command, using n as follows:
n Connector pin
[Notes] • When the connector is not used, the value of bit 0 is always 1.
• When DTR/DSR control is selected, the printer transmits only 1
byte after confirming that the host is ready to receive data (DSR
signal is SPACE). If the host computer is not ready to receive data
(DSR signal is MARK), the printer keeps waiting until the host is
ready. When XON/XOFF control is selected, the printer transmits
only 1 byte without checking the DSR signal.
• This command is executed when the data is processed in the
receive buffer. Therefore, there may be a time lag between
receiving the command and transmitting the status, depending on
the receive buffer status.
5-24 Commands
Off 00 0 Undefined.
1
On 02 2 Undefined.
Off 00 0 Undefined.
2
On 04 4 Undefined.
Off 00 0 Undefined.
3
On 08 8 Undefined.
Off 00 0 Undefined.
5
On 20 32 Undefined.
Off 00 0 Undefined.
6
On 40 64 Undefined.
ESC v
[Name] Transmit paper sensor status
[Format] ASCII ESC V
Hex 1B 76
Decimal 27 118
[Description] Transmits the current paper sensor status upon receiving this
command.
[Notes] • When DTR/DSR control is selected, the printer transmits only 1
byte after confirming that the host is ready to receive data (DSR
signal is SPACE).
If the host computer is not ready to receive data (DSR signal is
MARK), the printer waits until the host is ready. When XON/
XOFF control is selected, the printer transmits only 1 byte without
checking the DSR signal.
Commands 5-25
Off 00 0 Undefined.
2
On 04 4 Undefined.
Off 00 0 Undefined.
3
On 08 8 Undefined.
Off 00 0 Undefined.
5
On 20 32 Undefined.
Off 00 0 Undefined.
6
On 40 64 Undefined.
ESC { n
[Name] Turns on/off upside-down printing mode
[Format] ASCII ESC { n
Hex 1B 7B n
Decimal 27 123 n
[Range] 0 ≤ n ≤ 255
5-26 Commands
A B C D E F G A B C D E F G
0 1 2 3 4 5 6 0 1 2 3 4 5 6
GS I n
[Name] Transmit printer ID
[Format] ASCII GS I n
Hex 1D 49 n
Decimal 29 73 n
[Range] 1 ≤ n ≤ 3, 49 ≤ n ≤ 51
[Function] Transmits the printer ID specified by n as follows:
n = 2, Type ID
Off 00 0 Undefined.
2
On 04 4 Undefined.
Commands 5-27
Off 00 0 Undefined.
3
On 08 8 Undefined.
Off 00 0 Undefined.
5
On 20 32 Undefined.
Off 00 0 Undefined.
6
On 40 64 Undefined.
GS a n
[Name] Enable/Disable Automatic Status Back
[Format] ASCII GS a n
Hex 1D 61 n
Decimal 29 97 n
[Range] 0 ≤ n ≤ 255
[Description] Enables or disables ASB and specifies the status items to include,
using n as follows:
5-28 Commands
Off 00 0 Undefined.
3
On 08 8 Undefined.
Off 00 0 Undefined.
4
On 10 16 Undefined.
Off 00 0 Undefined.
6
On 40 64 Undefined.
Off 00 0 Undefined.
7
On 80 128 Undefined.
Commands 5-29
Off 00 0 On-line.
3
On 08 8 Off-line.
Off 00 0 Undefined.
0
On 01 1 Undefined.
Off 00 0 Undefined.
1
On 02 2 Undefined.
Off 00 0 Undefined.
2
On 04 4 Undefined.
Off 00 0 Undefined.
3
On 08 8 Undefined.
Off 00 0 Undefined.
6
On 40 64 Undefined.
5-30 Commands
Off 00 0 Undefined.
0
On 01 1 Undefined.
Off 00 0 Undefined.
1
On 02 2 Undefined.
Off 00 0 Undefined.
2
On 04 4 Undefined.
Off 00 0 Undefined.
3
On 08 8 Undefined.
Off 00 0 Undefined.
2
On 04 4 Undefined.
Off 00 0 Undefined.
3
On 08 8 Undefined.
Off 00 0 Undefined.
5
On 20 32 Undefined.
Commands 5-31
Off 00 0 Undefined.
6
On 40 64 Undefined.
GS r n
[Name] Transmit status
[Format] ASCII GS r n
Hex 1D 72 n
Decimal 29 114 n
[Range] 1 ≤ n ≤ 2, 49 ≤ n ≤ 50
[Description] Transmits the status specified by n as, follows:
n Function
5-32 Commands
Off 00 0 Undefined.
2
On 04 4 Undefined.
Off 00 0 Undefined.
3
On 08 8 Undefined.
Off 00 0 Undefined.
5
On 20 32 Undefined.
Off 00 0 Undefined.
6
On 40 64 Undefined.
Off 00 0 Undefined.
1
On 02 2 Undefined.
Off 00 0 Undefined.
2
On 04 4 Undefined.
Off 00 0 Undefined.
3
On 08 8 Undefined.
Commands 5-33
Off 00 0 Undefined.
5
On 20 32 Undefined.
Off 00 0 Undefined.
6
On 40 64 Undefined.
5-34 Commands