Professional Documents
Culture Documents
REPOR (1)
REPOR (1)
License #
OWNER:ANGOSOM HAGOS
LOCATION:SHERARO
STRACTURAL ANALISIS REPORT 21 JANUARY 2024
STRACTURAL ANALISIS REPORT 21 JANUARY 2024
STRACTURAL ANALISIS REPORT 21 JANUARY 2024
STRACTURAL ANALISIS REPORT 21 JANUARY 2024
INTRODUCTION PART
Introduction
This is a structural design document for G+1 COMMERCIAL building which is going to be constructed
in sheraro town. The building has a plan configuration as shown below.This structural design document
consists all the assumptions, analysis and design calculations .
Material
In the design of the building material properties of concrete C-25 and Steel S-300 are used for all
structural elements.
Slab design
The slab is designed according to EN ES2015, using coefficient method. The partition wall load
on each slab panel is considered as 20% of the slab weight distributed all over the panel area.
After calculation of the design actions, shear force and bending moment, the proper
reinforcement is provided for moment and the slab panel is checked against shear. The deflection
requirement is also checked for each slab panel.
Stair design
There is one stair in the building. The stairs are modeled as simply supported by the beams
running along the perpendicular directions. The analysis is done to determine the design actions
for which it is designed. The deflection requirement is checked.
STRACTURAL ANALISIS REPORT 21 JANUARY 2024
3D Analysis of Frames
After the transfer of slab loads and wall loads to the beams, 3D frame analysis is done to
determine the shear force and bending moment for beam design and axial load and the biaxial
moments for the design of columns. The 3D analysis of frame is done using SAP 2000 V14.
Beam Design
After determining the design shear and moments, the beams are designed according to EBCS-2
1995 part II and I. A detail design procedure is shown using spreadsheet format.
Column Design
After determining the axial load and biaxial moment, the columns are designed considering the
slenderness effect. A detail design procedure of a column design is attached to the backup sheet.
Footing Design
The footing is designed by selecting a representative footing with the highest design actions,
biaxial moments and axial loads. The design is done using spreadsheet format according to
EBCS. A bearing capacity of 400 kpa is taken for the design of footing considering that the soil
is non-cohesive soil (gravel) type soil.
STRACTURAL ANALISIS REPORT 21 JANUARY 2024
Basic Assumptions
Ground Properties
Soil Type gravel ,sand&gravel Soil
Loads Considered
Roof Structures Permanent, Imposed Wind Loads 0.5 KN/M2
Loads
Factors Used
Materials γc = 1.5; γs = 1.15
LOAD ON BEAM
dis
t(M) y(KN/M3) H(M) load(KN/m)
HCB
WALL WALL LOAD 0.2 14 2.7 7.56
BOTH
plasrering load 0.06 23 2.7 3.726 SIEDS
STAIRE 2 TO 4 2.5
BALCONI 2.5 TO 4 3
S-300 -0.100000 No
3. Load combinations
This section provides load combination information.
COMB1 DEAD No No No
COMB1 live
COMB2 COMB1 No No No
COMB2 WIND
envelop COMB1 No No No
envelop COMB2
COMB1 DEAD
COMB1 live
COMB2 COMB1
COMB2 WIND
envelop COMB1
envelop COMB2
Base reactions
REACTION AT SUPPORT
STRACTURAL ANALISIS REPORT 21 JANUARY 2024
STRACTURAL ANALISIS REPORT 21 JANUARY 2024
AXIAL FORCE
STRACTURAL ANALISIS REPORT 21 JANUARY 2024
STRACTURAL ANALISIS REPORT 21 JANUARY 2024
REACTION
TABLE: Joint Reactions
Join StepTyp
t OutputCase CaseType e F1 F2 F3 M1 M2 M3
Text Text Text Text KN KN KN KN-m KN-m KN-m
77 COMB1 Combination 0.512 0.221 265.776 -0.152 33.4692 -0.0609
77 COMB2 Combination 0.512 0.221 265.776 -0.152 33.4692 -0.0609
77 COMB3 Combination 0.512 0.221 265.776 -0.152 33.4692 -0.0609
77 ENVELOP Combination Max 0.512 0.221 265.776 -0.152 33.4692 -0.0609
77 ENVELOP Combination Min 0.512 0.221 265.776 -0.152 33.4692 -0.0609
78 COMB1 Combination 0.105 0.345 467.274 -0.4071 58.3898 -0.062
78 COMB2 Combination 0.105 0.345 467.274 -0.4071 58.3898 -0.062
78 COMB3 Combination 0.105 0.345 467.274 -0.4071 58.3898 -0.062
78 ENVELOP Combination Max 0.105 0.345 467.274 -0.4071 58.3898 -0.062
78 ENVELOP Combination Min 0.105 0.345 467.274 -0.4071 58.3898 -0.062
79 COMB1 Combination 0.011 0.488 296.011 -0.5139 36.9057 -0.1105
79 COMB2 Combination 0.011 0.488 296.011 -0.5139 36.9057 -0.1105
79 COMB3 Combination 0.011 0.488 296.011 -0.5139 36.9057 -0.1105
79 ENVELOP Combination Max 0.011 0.488 296.011 -0.5139 36.9057 -0.1105
79 ENVELOP Combination Min 0.011 0.488 296.011 -0.5139 36.9057 -0.1105
80 COMB1 Combination 0.336 -0.204 359.608 0.163 45.0309 0.0746
80 COMB2 Combination 0.336 -0.204 359.608 0.163 45.0309 0.0746
80 COMB3 Combination 0.336 -0.204 359.608 0.163 45.0309 0.0746
80 ENVELOP Combination Max 0.336 -0.204 359.608 0.163 45.0309 0.0746
80 ENVELOP Combination Min 0.336 -0.204 359.608 0.163 45.0309 0.0746
81 COMB1 Combination -0.058 0.207 588.636 -0.2576 73.3937 0.027
81 COMB2 Combination -0.058 0.207 588.636 -0.2576 73.3937 0.027
81 COMB3 Combination -0.058 0.207 588.636 -0.2576 73.3937 0.027
81 ENVELOP Combination Max -0.058 0.207 588.636 -0.2576 73.3937 0.027
81 ENVELOP Combination Min -0.058 0.207 588.636 -0.2576 73.3937 0.027
82 COMB1 Combination -0.236 0.022 305.239 -0.1751 37.8397 0.0558
82 COMB2 Combination -0.236 0.022 305.239 -0.1751 37.8397 0.0558
82 COMB3 Combination -0.236 0.022 305.239 -0.1751 37.8397 0.0558
82 ENVELOP Combination Max -0.236 0.022 305.239 -0.1751 37.8397 0.0558
82 ENVELOP Combination Min -0.236 0.022 305.239 -0.1751 37.8397 0.0558
83 COMB1 Combination -1.641 -0.518 349.992 0.3678 42.273 0.0639
83 COMB2 Combination -1.641 -0.518 349.992 0.3678 42.273 0.0639
STRACTURAL ANALISIS REPORT 21 JANUARY 2024