Professional Documents
Culture Documents
Vr7000 If8540 Installation Instructions
Vr7000 If8540 Installation Instructions
JUNCTION BOX
Model IF-8540
This information provides the installation instructions for the junction box IF-8540. The units pre-installed in the junc-
tion box change depending on the configuration purchased.
A: one MC-3000S-N and three MC-3020D-N
B: one MC-3000S-N and four MC-3020D-N
C: one MC-3000S-N, three MC-3020D-N and two MC-3010A-N
A maximum of six sensor adapters can be installed in the junction box (MC-300S-N included). In the case of config-
urations A and B, you can install the optional MC-3010A-N and MC-3020D-N additionally. When an additional unit
is installed, prepare the optional sensor adapter and cable assy.* as shown below.
*: For power supply and data communication, it is necessary to connect a cable assy. between sensor adapters. One
cable assy. is necessary per each additional unit.
• Sensor Adapter (Type: MC-3010A-N, no coating, for analog input)
• Sensor Adapter (Type: MC-3020D-N, no coating, for digital input)
• Cable Assy. (Type: AI.14-8AI.34-6L1000, Code No.: 000-177-250-10)
1 Included Items
The table shown below indicates included items in the junction box. The quantity of included items changes
depending to the configuration purchased.
A: one MC-3000S-N and three MC-3020D-N
B: one MC-3000S-N and four MC-3020D-N
C: one MC-3000S-N, three MC-3020D-N and two MC-3010A-N
Qty
Name Type Code No. Remarks
A B C
Junction Box IF-8540 - 1 1 1
Cosmetic Cap CP-30BC-10-BLACK 000-179-377-10 2 2 2
Cable Band PLF1M-M 000-116-921-10 27 27 27
AI 1,5-6 BK 000-176-412-10 10 10 10 For DPYC-1.5 cable
Rod Terminal AI 1-6 RD 000-176-413-10 60 80 60 For MPYC-12 cable
AI 0,75-6 GY 000-176-411-10 40 40 60 For TTYCSLA cable
FV2-4 BLU 000-157-247-10 1 1 1 For grounding the IF-8540
Crimp-on Lug
FV1.25-4(LF) RED 000-166-666-10 9 9 15 For drain wire of TTYCSLA cable
Spare Fuse FGMB 125V 3A PBF 000-157-481-10 3 3 3 For MC-3000S-N
www.furuno.com
All brand and product names are trademarks, registered trademarks or service marks of their respective holders.
2 Required Materials and Tools
Prepare the materials and tools shown below to install the junction box.
Name Qty Remarks
M10 Bolt 4 For fixing junction box. Coach screws (10) can be also used.
FR-FTPC-CY Cable 1 For LAN connection with DCU (VR-7010)
Ground Wire 1 IV-2sq.
DPYC-1.5 Cable* 1 For power connection (24 VDC)
TTYCSLA Cable* - For analog input
MPYC-12 Cable* - For digital input
Heat Shrink Tubing - For drain wire of TTYCSLA cable
Cable Tie - For fixing cables
Vinyl Tape - For cable protection
Crimping Tool 1 For attaching rod terminals (Type: CRIMPFOX 10S)
*: Many of the of the cables mentioned are JIS (Japanese Industrial Standards) cables. If not available locally, use
the equivalent. For details of the JIS cables, see the cable guide in the installation manual of the VDR (IME-44850).
3 Mounting Considerations
• Locate the unit away from heat sources. • The cable entrance of the unit must face downward.
• Select a location where the shock and vibration are minimal. • A magnetic compass will be affected if the unit is placed too
• Locate the unit away from places subject to water splash close to the magnetic compass. Observe the compass safe
and rain. distances to prevent interference to a magnetic compass.
MC-3000S-N: 2.05 m (standard), 1.35 m (steering)
• Make the maintenance space shown in the outline drawing
MC-3010A-N: 0.75 m (standard), 0.50 m (steering)
at the middle of this manual for maintenance and checking MC-3020D-N: 1.05 m (standard), 0.70 m (steering)
purpose.
• Select a location where the surface is flat. If it is not flat, insert
• Select a mounting location considering the length of the
a number of washers between the unit and the mounting
cables to be connected to this unit. location as necessary.
• Select a location that is strong enough to support the weight
of the unit.
Eye bolt
M10 bolt
(or coach screw)
Junction box
2
5 Mounting an Additional Sensor Adapter(s) (Option)
䕆 㻌5 - 1 M o u n t i n g a n A d d i t i o n a l S e n s o r A d a p t e r ( s )
Install the additional sensor adapter(s) (MC-3010A-N and MC-3020D-N) at the locations “E” and “F” indicated in the
figure below. The unit may be pre-installed at the location “E” and “F”, depending the configuration purchased.
Front
D E • A: MC-3000S-N*1
• B to D: MC-3020D-N*1
• E and F: Mounting location for additional unit*2
C F
1. Unfasten seven binding screws (M4×10) to remove the junction box cover.
Binding screw
䠄7 pcs䠅
Wire saddle:
Release the cable from this wire
Wire saddle:
saddle to install the first additional
Release the cable from this wire
unit.
saddle to install the second
additional unit.
3. Slightly loosen two binding screws (M4×10) to pull out the fixing plate.
Note: Loosen the binding screws only enough to pull out the fixing plate. If the screws are loosened too much,
the plate may fall and be damaged when it is hung in the next step.
3
4. Hang the plate to the screws loosened at step 3.
The figure below is an example for the first additional unit.
Unfasten these binding screws
to pull out the fixing plate.
Fixing plate
5. Unfasten four binding screws (M4×10) to remove the additional sensor adapter cover.
6. Fix the unit to the fixing plate with four binding screws (M4×10, supplied with sensor adapter).
Binding screw
(4 pcs) Sensor adapter
(MC-3010A-N or
MC-3020D-N䠅
J2 J1
MC-3020D-N Second additional unit*
J1
*: The unit may be pre-installed and the internal
wiring completed depending on the configuration
J2
MC-3020D-N purchased.
J1
J1
MC-3000S-N
J2
J1
24 VDC
8. See “8. Wiring for MC-3000S-N” (page 7) and “9. Wiring for MC-3020D-N and MC-3010A-N” (page 9) to connect
the cable from the external equipment to the sensor adapter.
9. See “5-2. Setting the Termination Resistor and Modbus Address” (page 5) to set the termination resistor and
Modbus address.
4
10. Reattach the sensor adapter cover.
11. Insert the fixing plate to the original location, then fasten two binding screws loosened at step 3.
12. Fix the internal wiring cable released at step 2 with the wire saddle.
13. Check the checkmark(s) on the label on the rear side of the junction box cover, according to the additional
unit(s).
The label on the rear side of the junction box cover
U18 U18
Front When additional unit is installed at the location “E” only ( “F” is not used)
Location Terminal resistor (J25) Modbus address (U18)
D E D Short between 2 and 3 pin (termination resistor: OFF). Keep the default setting.
E Short between 1 and 2 pin (termination resistor: ON). “Set to “4” .
C F
When additional unit is installed at both location “E” and “F”
B Location Terminal resistor (J25) Modbus address (U18)
D Short between 2 and 3 pin (termination resistor: OFF). Keep the default setting.
A E Short between 2 and 3 pin (termination resistor: OFF). Set to “4” .
F Short between 1 and 2 pin (termination resistor: ON). Set to “5” .
5
6 Power Supply (24 VDC)
Power for the junction box (24 VDC) is supplied from the DCU (VR-7010). Use the DPYC-1.5 (local supply) to con-
nect between the J1 port on the junction box and J313 port on the DCU. For wiring the DCU, see the installation
manual of the VDR (IME-44850).
1. Fabricate the DPYC-1.5 cable as shown below.
6 mm
Armor Sheath
80 mm
0.5 to 1 mm
Vinyl tape (Width: 20 mm)
Crimp the rod terminals (AI1.5-6
BK, supplied), using the crimping
tool (CRIMPFOX 10S). After
crimping, confirm that the 0.5 to
1 mm of the wires are exposed.
2. Unfasten seven binding screws (M4×10) to remove the junction box cover.
3. Pass the wires through the cable entrance, then connect them to the J1 port.
䠇䠉
Opener
J1 port
4. Fix the cable to the cable clamp, using a cable tie (local supply).
Note: The armor of the cable should contact the cable clamp.
6
7 Grounding
Attach the crimp-on lug (FV2-4 BLU, supplied) to the ground wire (IV-2sq., local supply), then fix it to the ground
terminal.
Ground
terminal
Ground wire
600 mm
Pass the heat shrink tubing (local supply)
onto the drain wire, then attach the crimp-on
lug (FV1.25-4 (LF) RED, supplied) to it.
Vinyl tape (Width: 20 mm) 0.5 to 1 mm
Crimp-on lug
Crimp the rod terminals (AI 0,75-6
GY, supplied), using the crimping
tool (CRIMPFOX 10S). After crimp-
ing, confirm that the 0.5 to 1 mm of
the wires are exposed.
FR-FTPC-CY cable
Cable jacket Inner sheath LAN connector
500 mm
2. Unfasten seven binding screws (M4×10) to remove the junction box cover.
7
3. Release the internal wiring cable from the wire saddles and CKS clamps.
MC-3000S-N
Wire saddle
(2 pcs)
4. Slightly loosen two binding screws (M4×10) to hang the fixing plate at the step 6.
Note: Loosen the binding screws only enough to hang the fixing plate. If the screws are loosened too much, the
plate may fall and be damaged when it is hung in the step 6.
5. Slightly loosen two binding screws (M4×10) to pull out the bottom fixing plate.
6. Hang the plate (MC-3000S-N) to the screws loosened at step 4.
Fixing plate
7. Unfasten four binding screws (M4×10) to remove the sensor adapter cover.
8
8. Pass the cables through the cable entrance, then fix the cables to the cable clamp with a cable tie (local supply).
Note 1: The armor of the cable should contact the cable clamp.
Note 2: The fixing locations for the cables are not specified. However, see the figure below for reference.
7 6 No. Cable Access point
1 FR-FTPC-CY
4 3 2 1 5 2 TTYCSLA-1Q MC-3000S-N
3 TTYCSLA-4
4 TTYCSLA-1
5 DPYC-1.5 J1 port (IF-8540)
6 MPYC-12 MC-3020D-N
7 TTYCSLA-1 MC-3010A-N
9. Attach a cable band (supplied) to each cable to be connected to the junction box and record sensor name/equip-
ment name on each cable band.
10. Fix the drain wires of the TTYCSLA cables to the locations shown below.
Fixing screws for the drain wires are preattached to the unit.
11. Connect the cables to respective connectors on the sensor adapter, referring to the interconnection diagram at
the middle of this document and the sticker attached to the rear side of the sensor adapter cover.
12. Reattach the sensor adapter cover and replace the fixing plate to the original location.
13. Fasten the binding screws loosened at step 4 and step 5.
14. Fix the internal wiring cable released at step 3 with the wire saddles and CKS clamps.
15. Reattach the junction box cover.
0.5 to 1 mm
Vinyl tape (Width: 20 mm)
Crimp the rod terminals (AI 1-6 RD,
supplied), using the crimping tool
(CRIMPFOX 10S). After crimping,
confirm that the 0.5 to 1 mm of the
wires are exposed.
9
TTYCSLA cable (for MC-3010A-N)
Aluminum tape
60 mm
Sheath
5 mm
Armor 6 mm
Drain wire
L
Pass the heat shrink tubing (local supply)
onto the drain wire, then attach the crimp-on
lug (FV1.25-4 (LF) RED, supplied) to it.
Vinyl tape (Width: 20 mm)
0.5 to 1 mm
Crimp-on lug
Crimp the rod terminals (AI 0,75-6
GY, supplied), using the crimping tool
(CRIMPFOX 10S). After crimping,
confirm that the 0.5 to 1 mm of the
The length of “L”
Front
Location The length of “L”
D E
B 900 mm
C F C 900 mm
B D 1000 mm
E 1000 mm
A
F 900 mm
2. Unfasten seven binding screws (M4×10) to remove the junction box cover.
3. Release the internal wiring cables from the wire saddles.
Wire saddle
4. Slightly loosen two binding screws (M4×10) to pull out the fixing plate.
Note: Loosen the binding screws only enough to pull out the fixing plate. If the screws are loosened too much,
the plate may fall and be damaged when it is hung in the next step.
10
5. Hang the plate to the screws loosened at step 4.
The figure below is an example for hanging the second fixing plate from the top.
Fixing plate
6. Unfasten four binding screws (M4×10) to remove the sensor adapter cover.
7. Pass the cables through the cable entrance, then fix the cables to the cable clamp with a cable ties (local sup-
ply).
Note 1: The armor of the cable should contact the cable clamp.
Note 2: The fixing locations for the cables are not specified. However, see the figure below for reference.
7 6 No. Cable Access point
1 FR-FTPC-CY
4 3 2 1 5 2 TTYCSLA-1Q MC-3000S-N
3 TTYCSLA-4
4 TTYCSLA-1
5 DPYC-1.5 J1 port (IF-8540)
6 MPYC-12 MC-3020D-N
7 TTYCSLA-1 MC-3010A-N
8. Attach a cable band (supplied) to each cable to be connected to the junction box and record sensor name/equip-
ment name on each cable band.
9. Fix the drain wires of the TTYCSLA cables to the locations in- : Fixing locations for the drain wires
dicated in the figure to the right.
Fixing screws for the drain wires are preattached to the unit.
10. Connect the cables to respective connectors on the sensor
adapter, referring to the interconnection diagram at the middle
of this document and the sticker attached to the rear side of
the sensor adapter cover.
11. Reattach the sensor adapter cover and replace the fixing
plate to the original location.
12. Fasten two binding screws loosened at step 4.
13. Fix the internal wiring cable released at step 3 with the wire saddle.
14. Bundle the cables with the wiring duct and fix them with the CKS clamp.
11
17/Jul/2015 H.MAKI
'
&
%
$
127(
ὀグ
࣮࣒ࣛ
,9VT
$/$50 77<&6/$
9'&
᥋⥆⟽
- - -
,)
'3<&
9 9B,1
㸨㸰㸧ฟⲴ㑅ᢥࠋ
㸨㸯㸧㐀⯪ᡤᡭ㓄ࠋ
9 9B*1'
95
6+,3<$5' 6833/<
-81&7,21 %2;
1& 3:5B)$,/B$
3:5B)$,/B&20
6(/(&7 $7 385&+$6(
3:5B)$,/B%
1& - $,$, - - $,$, - -
9B9287 / /
/$1 9B,1 9B287 9B,1 9B287
-
ࢹ࣮ࢱ㞟ࣘࢽࢵࢺ
3
,(& 7'% - -
5'$ '&9B287 '&9B287
3
5'% ',*,B,1 ',*,B,1
㑅ᢥ
- ',*,B,1 ',*,B,1
6(1625 $'$37(5
ࢭࣥࢧ࣮ࢲࣉࢱ࣮
5'$ - -
5'% '&9B287 '&9B287
,62*1' ',*,B,1 ',*,B,1
5'+ ',*,B571 ',*,B571
3
5'& *1' *1'
- '&9B287 '&9B287
ྠୖ 7'$ ',*,B,1 ',*,B,1
3
',772 7'% ',*,B571 ',*,B571
5'$ *1' *1'
3
5'% - -
,62*1' '&9B287 '&9B287
5'+ ',*,B,1 ',*,B,1
5'& ',*,B571 ',*,B571
- *1' *1'
7'$ '&9B287 '&9B287
3
7'% ',*,B,1 ',*,B,1
5'$ ',*,B571 ',*,B571
5'% *1' *1'
,62*1' - -
5'+ '&9B287 '&9B287
3
5'& ',*,B,1 ',*,B,1
- ',*,B571 ',*,B571
6(5,$/ 77<&6/$4 7'$ *1' *1'
,(& 7'% '&9B287 '&9B287
5'+ ',*,B,1 ',*,B,1
5'& ',*,B571 ',*,B571
7'$ *1' *1'
ྠୖ 7'%
',772 5'+
5'&
-
7'$
7'% - - $,$, - -
/
5'+ 9B287 9B,1 9B287 9B,1
5'& 9B*1' 9B*1' 9B*1' 9B*1'
7'$ 02'%86$ 02'%86$ 02'%86$ 02'%86$
7'% 02'%86% 02'%86% 02'%86% 02'%86%
5'+ *1' *1' *1' *1'
5'&
6&$/(
'5$:1
',*,7$/ ,1
':* 1R
&+(&.('
-
$33529('
&217$&7 &/2685(
'&9B287
03<&
',*,B,1
',*,B571
03<&
$XJ
$XJ
*1'
0&'
',*,7$/ ,1
'&9B287
03<&
',*,7$/ ,1
',*,B,1
0&'
0$66
6(1625 $'$37(5
',*,B571
03<&
6(1625 $'$37(5
+0$.,
*1'
30/Aug/2016 H.MAKI
&& &
-
03<&
'&9B287
7<$0$6$.,
NJ
',*,B,1
03<& ',*,B571
*1'
25
'&9B287
5()1R
',*,B,1
ࡲࡓࡣ
',*,B571
*1'
- $,$, - - -
956
/
9B,1 9B287 9B,1 '&9B287
9B*1' 9B*1' 9B*1' ',*,B,1
0&$
02'%86$ 02'%86$ 02'%86$ ',*,B571
02'%86% 02'%86% 02'%86% *1'
0&' 25
*1' *1' *1' '&9B287
6(1625 $'$37(5
',*,B,1
- ',*,B571
77<&6/$
$1$/2* $1B,1 *1'
$1B*1' -
&855B-3 '&9B287
1$0(
ྡ⛠
&855B-3 ',*,B,1
7,7/(
- ',*,B571
ྠୖ $1B,1 *1'
',772 $1B*1' '&9B287
- *1'
᥋⥆⟽
$1B,1
,)
$1B*1'
&855B-3
┦⤖⥺ᅗ
6(1625 $'$37(5
0&$
-81&7,21 %2;
,17(5&211(&7,21 ',$*5$0
㻡㻚㻌 ᡭ㡰 㻠 䛷⦆䜑䛯䝛䝆䛻䝉 䞁䝃䞊䜰䝎 䝥 䝍 䞊ྲྀ䛡ྎ䜢䛡䜎䛩䚹
ḟᅗࡣࠊୖࡽ 2 ẁ┠ࡢࢭࣥࢧ࣮ࢲࣉࢱ࣮ྲྀࡅྎࢆࡅࡓࡁࡢ࡛ࡍࠋ
䝞䜲䞁䝗䝛䝆
䝉䞁䝃䞊䜰䝎䝥䝍䞊
ྲྀ䛡ྎ
11
㼀㼀㼅㻯㻿㻸㻭 䜿䞊䝤䝹䛾➃ᮎฎ⌮ 䠄㻹㻯㻙㻟㻜㻝㻜㻭㻙㻺 ⏝䠅
䜰䝹䝭䝔䞊䝥
㻢㻜㼙㼙
䝡䝙䞊䝹䝅䞊䝇
㻡㼙㼙
䛒䛨䜝䛜䛔
䝗䝺䜲䞁⥺ 㻢㼙㼙
䝗䝺䜲䞁⥺䛻䛿䚸⇕⦰䝏䝳䞊䝤䠄⌧ᆅᡭ㓄䠅䜢ᕳ䛝䚸ᨭ
⤥䛾ᅽ╔➃Ꮚ䠄㻲㼂㻝㻚㻞㻡㻙㻠㻔㻸㻲㻕㻌㻾㻱㻰䠅䜢ྲྀ䜚䛡䜎䛩䚹
䝡䝙䞊䝹䝔䞊䝥㻌䠄ᖜ䠖㻞㻜㼙㼙䠅 㻜㻚㻡䡚㻝㼙㼙
ᅽ╔➃Ꮚ
ⰺ⥺䛻ᨭ⤥䛾Წ➃Ꮚ䠄㻭㻵㻌㻜㻘㻣㻡㻙㻢㻌㻳㼅䠅䜢ྲྀ䜚
䛡䚸ᅽ╔ᕤල䠄㻯㻾㻵㻹㻼㻲㻻㼄㻌㻝㻜㻿䠅䛷ᅽ╔䛧䜎䛩䚹
ᅽ╔ᚋ䚸ⰺ⥺䛜Წ➃Ꮚ䛛䜙㻜㻚㻡䡚㻝㼙㼙⛬ᗘ✺䛝
ฟ䜛䛣䛸䜢☜ㄆ䛧䛶䛟䛰䛥䛔䚹
㻸 䛾㛗 䛥
ࢭࣥࢧ࣮ࢲࣉࢱ࣮ࡢྲྀ⨨ᛂࡌ࡚ࠊⰺ⥺ࡢ㛗ࡉ㸦L㸧ࢆㄪᩚࡋ࡚ࡃࡔࡉ࠸㸦ḟ⾲ཧ↷㸧ࠋ
๓
ഛሙᡤ 㻸 䛾㛗䛥
㻰 㻱
㻮 㻥㻜㻜㼙㼙
㻯 㻲 㻯 㻥㻜㻜㼙㼙
㻮 㻰 㻝㻜㻜㻜㼙㼙
㻱 㻝㻜㻜㻜㼙㼙
㻭
㻲 㻥㻜㻜㼙㼙
䝽䜲䝲䞊䝃䝗䝹
10
㻤㻚㻌 ྛ䜿䞊䝤䝹䜢 䜿䞊䝤䝹ᑟධཱྀ䛻㏻ 䛧 䛯䛒 䛸 䚸 ᮰⥺䝞䞁 䝗 䠄⌧ᆅᡭ㓄䠅 䜢 䛳 䛶䜿䞊䝤䝹䜽 䝷 䞁 䝥䛻䜿䞊䝤䝹
䜢ᅛᐃ 䛧 䜎䛩䚹
ὀ 1㸧ࢣ࣮ࣈࣝࡢ࠶ࡌࢁእࢆࢣ࣮ࣈࣝࢡࣛࣥࣉᅛᐃࡋ࡚ࡃࡔࡉ࠸ࠋ
ὀ 2㸧ྛࢣ࣮ࣈࣝࡢᅛᐃ⨨ᣦᐃࡣ࠶ࡾࡲࡏࢇࠋḟᅗࡣࠊࢣ࣮ࣈࣝᅛᐃ⨨ࡢཧ⪃ࣞ࢘ࢺ࡛ࡍࠋ
㻣 㻢 㻺㼛㻚 䜿䞊䝤䝹 ᥋⥆ඛ
㻝 㻲㻾㻙㻲㼀㻼㻯㻙㻯㼅
㻞 㼀㼀㼅㻯㻿㻸㻭㻙㻝㻽
㻠 㻟 㻞 㻝 㻡 㻹㻯㻙㻟㻜㻜㻜㻿㻙㻺
㻟 㼀㼀㼅㻯㻿㻸㻭㻙㻠
㻠 㼀㼀㼅㻯㻿㻸㻭㻙㻝
㻡 㻰㻼㼅㻯㻙㻝㻚㻡 㻶㻝 䝫䞊䝖 䠄㻵㻲㻙㻤㻡㻠㻜 ᮏయ䠅
㻢 㻹㻼㼅㻯㻙㻝㻞 㻹㻯㻙㻟㻜㻞㻜㻰㻙㻺
㻣 㼀㼀㼅㻯㻿㻸㻭㻙㻝 㻹㻯㻙㻟㻜㻝㻜㻭㻙㻺
㻥㻚㻌 ᥋⥆䛩䜛 䝉 䞁䝃䞊ྡ䜔ᶵჾྡ䛜䜟䛛䜛 䜘 䛖 䛻䚸 ྛ䜿䞊䝤䝹䛻ᨭ⤥䛾䜿䞊䝤䝹䝞䞁 䝗 䜢ᕳ䛝 䛴䛡䜎䛩䚹
㻝㻜㻚㻌 㼀㼀㼅㻯㻿㻸㻭 䜿䞊䝤䝹䛾 䝗 䝺 䜲 䞁⥺䜢ḟᅗ䛾⨨䛻䝛䝆Ṇ䜑 䛧 䜎䛩䚹
ࢻࣞࣥ⥺ᅛᐃ⏝ࡢࢿࢪࡣࠊᮏయྲྀࡾࡅࡽࢀ࡚࠸ࡲࡍ
䠖 䝗䝺䜲䞁⥺ᅛᐃ⨨
䝡䝙䞊䝹䝔䞊䝥㻌䠄ᖜ䠖㻞㻜㼙㼙䠅 㻜㻚㻡䡚㻝㼙㼙
ⰺ⥺䛻ᨭ⤥䛾Წ➃Ꮚ䠄㻭㻵㻌㻝㻙㻢㻌㻾㻰䠅䜢ྲྀ䜚
䛡䚸ᅽ╔ᕤල䠄㻯㻾㻵㻹㻼㻲㻻㼄㻌㻝㻜㻿䠅䛷ᅽ╔
䛧䜎䛩䚹ᅽ╔ᚋ䚸ⰺ⥺䛜Წ➃Ꮚ䛛䜙㻜㻚㻡䡚
㻝㼙㼙⛬ᗘ✺䛝ฟ䜛䛣䛸䜢☜ㄆ䛧䛶䛟䛰䛥䛔䚹
9
㻟㻚㻌 ḟᅗ䛾⨨䛻䛒䜛 䝽 䜲䝲䞊䝃 䝗 䝹 䛸 㻯㻷㻿 䜽 䝷 䞁 䝥䛛 䜙䚸 ෆ㒊㓄⥺⏝䛾䜿䞊䝤䝹䜢ゎᨺ 䛧 䜎䛩䚹
㻹㻯㻙㻟㻜㻜㻜㻿㻙㻺
䝽䜲䝲䞊䝃䝗䝹
䠄㻞 䜹ᡤ䠅
䝞䜲䞁䝗䝛䝆
䝞䜲䞁䝗䝛䝆
䝉䞁䝃䞊䜰䝎䝥䝍䞊ྲྀ䛡ྎ
8
㻣 䜰䞊䝇⥺䛾᥋⥆
䜰䞊䝇➃Ꮚ
䜰䞊䝇⥺
㻤 㻹㻯㻙㻟㻜㻜㻜㻿㻙㻺 䛾⤖⥺
㻢㻜㻜㼙㼙
䝗䝺䜲䞁⥺䛻䛿䚸⇕⦰䝏䝳䞊䝤䠄⌧ᆅᡭ㓄䠅䜢ᕳ䛝䚸ᨭ
⤥䛾ᅽ╔➃Ꮚ䠄㻲㼂㻝㻚㻞㻡㻙㻠㻔㻸㻲㻕㻌㻾㻱㻰䠅䜢ྲྀ䜚䛡䜎䛩䚹
䝡䝙䞊䝹䝔䞊䝥㻌䠄ᖜ䠖㻞㻜㼙㼙䠅 㻜㻚㻡䡚㻝㼙㼙
ᅽ╔➃Ꮚ
ⰺ⥺䛻ᨭ⤥䛾Წ➃Ꮚ䠄㻭㻵㻌㻜㻘㻣㻡㻙㻢㻌㻳㼅䠅䜢ྲྀ䜚
䛡䚸ᅽ╔ᕤල䠄㻯㻾㻵㻹㻼㻲㻻㼄㻌㻝㻜㻿䠅䛷ᅽ╔䛧
䜎䛩䚹ᅽ╔ᚋ䚸ⰺ⥺䛜Წ➃Ꮚ䛛䜙㻜㻚㻡䡚㻝㼙㼙
⛬ᗘ✺䛝ฟ䜛䛣䛸䜢☜ㄆ䛧䛶䛟䛰䛥䛔䚹
㻲㻾㻙㻲㼀㻼㻯㻙㻯㼅 䜿䞊䝤䝹䛾➃ᮎฎ⌮
⿕そ ෆ㒊䝡䝙䞊䝹䝅䞊䝇 㻸㻭㻺䝁䝛䜽䝍
㻡㻜㻜㼙㼙
7
㻢 㟁※ 䠄㻰㻯㻞㻠㼂䠅 䛾᥋⥆
㻤㻜㼙㼙
㻜㻚㻡䡚㻝㼙㼙
䝡䝙䞊䝹䝔䞊䝥㻌䠄ᖜ䠖㻞㻜㼙㼙䠅
ⰺ⥺䛻ᨭ⤥䛾Წ➃Ꮚ䠄㻭㻵㻝㻚㻡㻙㻢㻌㻮㻷䠅䜢ྲྀ䜚
䛡䚸ᅽ╔ᕤල䠄㻯㻾㻵㻹㻼㻲㻻㼄㻌㻝㻜㻿䠅䛷ᅽ╔
䛧䜎䛩䚹ᅽ╔ᚋ䚸ⰺ⥺䛜Წ➃Ꮚ䛛䜙㻜㻚㻡䡚
㻝㼙㼙⛬ᗘ✺䛝ฟ䜛䛣䛸䜢☜ㄆ䛧䛶䛟䛰䛥䛔䚹
䝁䝛䜽䝍䛾䝒䝯䜢ᢲ䛧䛺䛜䜙䚸 ⰺ⥺
䜢ᤄධ䛧䜎䛩䚹
䠇 䠉
䝒䝯
㻶㻝 䝫䞊䝖
᮰⥺䝞䞁䝗䜢䛳䛶䜿䞊䝤䝹
䜽䝷䞁䝥䛻ᅛᐃ䛧䜎䛩䚹
6
㻝㻜㻚㻌 䝉 䞁䝃䞊䜰䝎 䝥 䝍 䞊䛾䜹䝞䞊䜢ඖ䛾⨨䛻ྲྀ 䜚 䛡䜎䛩䚹
㻝㻝㻚㻌 䝉 䞁䝃䞊䜰䝎 䝥 䝍 䞊ྲྀ䛡ྎ䜢ඖ䛾⨨䛻ᡠ 䛧 䚸 ᡭ㡰 㻟 䛷⦆䜑䛯䝞䜲 䞁 䝗 䝛䝆 㻞 ᮏ䜢⥾䜑䛡䜎䛩䚹
㻝㻞㻚㻌 ᡭ㡰 㻞 䛷እ 䛧 䛯䝽 䜲䝲䞊䝃 䝗 䝹䜢䛳 䛶䚸 ෆ㒊㓄⥺⏝䛾䜿䞊䝤䝹䜢ᅛᐃ 䛧 䜎䛩䚹
㻝㻟㻚㻌 ᥋⥆⟽䛾䜹䝞䞊⫼㠃䛻䛒 䜛 䝇 䝔 䝑 䜹 䞊䛻䚸 ㏣ຍഛ 䛧 䛯䝴䝙 䝑 䝖 䛻ᛂ 䛨 䛶䝏 䜵 䝑 䜽 䝬䞊 䜽 䜢ධ䜜䜎䛩䚹
䜹䝞䞊⫼㠃䛾䝇䝔䝑䜹䞊
㏣ຍഛ䛧䛯䝴䝙䝑䝖䛻ᛂ䛨䛶䚸
䝏䜵䝑䜽䝬䞊䜽䜢ධ䜜䜎䛩䚹
䕆 㻌㻌㻡㻙
㻡 㻙 㻞 㻌⤊ ➃ ᢠ 䛚 䜘
䜘䜃㻹
䜃㻹 㼛㼐㼎㼡㼟 䜰 䝗䝺䝇
䝗䝺 䝇䛾タᐃ
䛾タᐃ
㼁㻝㻤 㼁㻝㻤
๓ 㻱 䛾⨨䛻䛾䜏䝉䞁䝃䞊䜰䝎䝥䝍䞊㏣ຍഛ䛩䜛ሙྜ 䠄㻲 䛿ᮍ⏝䠅 䠖
ഛሙᡤ ⤊➃ᢠ䛾タᐃ 䠄㻶㻞㻡䠅 㻹㼛㼐㼎㼡㼟 䜰䝗䝺䝇䛾タᐃ 䠄㼁㻝㻤䠅
㻰 㻱 㻰 㻞㻙㻟 䝢䞁㛫䜢䝅䝵䞊䝖 䠄⤊➃ᢠ䛺䛧䠅 ኚ᭦せ
㻱 㻝㻙㻞 䝢䞁㛫䜢䝅䝵䞊䝖 䠄⤊➃ᢠ䛒䜚䠅 䛂㻠䛃 䛻タᐃ
㻯 㻲
㻱 䛚䜘䜃 㻲 䛾⨨䛻䝉䞁䝃䞊䜰䝎䝥䝍䞊㏣ຍഛ䛩䜛ሙྜ 䠖
㻮 ഛሙᡤ ⤊➃ᢠ䛾タᐃ 䠄㻶㻞㻡䠅 㻹㼛㼐㼎㼡㼟 䜰䝗䝺䝇䛾タᐃ 䠄㼁㻝㻤䠅
㻰 㻞㻙㻟 䝢䞁㛫䜢䝅䝵䞊䝖 䠄⤊➃ᢠ䛺䛧䠅 ኚ᭦せ
㻭 㻱 㻞㻙㻟 䝢䞁㛫䜢䝅䝵䞊䝖 䠄⤊➃ᢠ䛺䛧䠅 䛂㻠䛃 䛻タᐃ
㻲 㻝㻙㻞 䝢䞁㛫䜢䝅䝵䞊䝖 䠄⤊➃ᢠ䛒䜚䠅 䛂㻡䛃 䛻タᐃ
5
㻠㻚㻌 ᡭ㡰 㻟 䛷⦆䜑䛯䝛䝆䛻䝉 䞁䝃䞊䜰䝎 䝥 䝍 䞊ྲྀ䛡ྎ䜢䛡䜎䛩 䠄ḟᅗཧ↷䠅䚹
ḟᅗࡣࠊ᭱ୖẁ㏣ຍࣘࢽࢵࢺࢆഛࡍࡿሙྜࡢ࡛ࡍࠋ
䝞䜲䞁䝗䝛䝆
䝉䞁䝃䞊䜰䝎䝥䝍䞊
ྲྀ䛡ྎ
䝞䜲䞁䝗䝛䝆
㻔㻠 ᮏ 㻕
䝉䞁䝃䞊䜰䝎䝥䝍䞊
䠄㻹㻯㻙㻟㻜㻝㻜㻭㻙㻺 䜎䛯䛿
㻹㻯㻙㻟㻜㻞㻜㻰㻙㻺䠅
㻹㻯㻙㻟㻜㻞㻜㻰㻙㻺 ㏣ຍ䝴䝙䝑䝖 㻖 ๓
㻶㻝 㻶㻞 㻶㻝 㻶㻞
㻶㻞 㻶㻝
㻹㻯㻙㻟㻜㻞㻜㻰㻙㻺 ㏣ຍ䝴䝙䝑䝖 㻖 㻖
㻶㻝 䠖 ฟⲴ䛾ᵝ㑅ᢥ䛻䜘䛳䛶䛿䚸 䝴䝙䝑䝖
ྲྀ䛡䚸 䛚䜘䜃ෆ㒊㓄⥺῭䜏䛾ᵝ䜒䛒
㻶㻞 䜚䜎䛩䚹
㻹㻯㻙㻟㻜㻞㻜㻰㻙㻺
㻶㻝
㻶㻝
㻹㻯㻙㻟㻜㻜㻜㻿㻙㻺
㻶㻞
㻶㻝
㻰㻯㻞㻠㼂
㻤㻚㻌 䛂㻤㻚㻌㻹㻯㻙㻟㻜㻜㻜㻿㻙㻺 䛾⤖⥺䛃 䠄㻣 䝨䞊䝆䠅 䛸 䛂㻥㻚㻌㻹㻯㻙㻟㻜㻞㻜㻰㻙㻺 䛚䜘䜃 㻹㻯㻙㻟㻜㻝㻜㻭㻙㻺 䛾⤖⥺䛃 䠄㻥 䝨䞊䝆䠅 䜢ཧ↷ 䛧
䛶䚸 ྛ䝉 䞁䝃䞊䜰䝎 䝥 䝍 䞊 䛸 እ㒊ᶵჾ䛾᥋⥆䜢⾜䛔䜎䛩䚹
㻥㻚㻌 䛂㻡㻙㻞㻚㻌⤊➃ᢠ䛚䜘䜃 㻹㼛㼐㼎㼡㼟 䜰 䝗 䝺 䝇䛾タᐃ䛃 䠄㻡 䝨䞊䝆䠅 䜢ཧ↷ 䛧 䛶䚸 ⤊➃ᢠ䛚䜘䜃 㻹㼛㼐㼎㼡㼟 䜰 䝗 䝺 䝇䛾
タᐃ䜢⾜䛔䜎䛩䚹
4
㻡 䝉䞁䝃䞊䜰䝎䝥䝍䞊䛾㏣ຍഛ 䠄䜸䝥䝅䝵䞁䠅
䕆㻌㻡㻡 㻙 㻝 㻌㏣ ຍ 䝴䝙 䝑 䝖
䕆㻌 䝖䛾ྲྀ䛡
䛾ྲྀ䛡
䜸䝥䝅 䝵 䞁䛾䝉 䞁䝃䞊䜰 䝎䝥 䝍 䞊 䠄㻹㻯㻙㻟㻜㻝㻜㻭㻙㻺 䜎 䛯䛿 㻹㻯㻙㻟㻜㻞㻜㻰㻙㻺䠅 䜢㏣ຍഛ䛩 䜛 ሙྜ䛿䚸 ḟᅗ䛾 㻱 䛚 䜘 䜃
㻲 䛾⨨䛻ྲྀ 䜚 䛡 䜎䛩䚹 ฟⲴ䛾ᵝ㑅ᢥ䛻 䜘 䛳 䛶䛿䚸 㻱 䛚 䜘 䜃 㻲 䛾⨨䛻䝴䝙 䝑 䝖 ྲྀ䛡῭䜏䛾ሙྜ 䜒 䛒 䜚
䜎䛩䚹
๓
㻰 㻱 䞉 㻭 䠖 㻹㻯㻙㻟㻜㻜㻜㻿㻙㻺㻖㻝
䞉 㻮 䡚 㻰 䠖 㻹㻯㻙㻟㻜㻞㻜㻰㻙㻺㻖㻝
䞉 㻱 䛚䜘䜃 㻲 䠖 ㏣ຍ䝴䝙䝑䝖䛾ྲྀ⨨ 㻖㻞
㻯 㻲
㻖㻝
㻮 ⏝ྍ 䠖 ᥋⥆⟽ෆ㒊䛻ྲྀ䜚䛡䜙䜜䛯≧ែ䛷ฟⲴ䛥䜜䜎䛩䚹
㻖㻞
䠖 ฟⲴ䛻䝴䝙䝑䝖ྲྀ䛡῭䜏䛾ሙྜ䛿䚸 ㏣ຍ䝴䝙䝑䝖
㻭 䛾ྲྀ䛡䛿䛷䛝䜎䛫䜣䚹
䝞䜲䞁䝗䝛䝆
䠄㻣 ᮏ䠅
䜹䝞䞊
䝽䜲䝲䞊䝃䝗䝹 䠖
᭱ୖẁ䛻㏣ຍ䝴䝙䝑䝖䜢ྲྀ䜚䛡䜛䛸䛝
䝽䜲䝲䞊䝃䝗䝹 䠖
䛿䚸 䛣䛾䝽䜲䝲䞊䝃䝗䝹䛷ᅛᐃ䛥䜜䛶
㻞 ẁ┠䛻㏣ຍ䝴䝙䝑䝖䜢ྲྀ䜚䛡䜛䛸䛝
䛔䜛䜿䞊䝤䝹䜢ゎᨺ䛧䜎䛩䚹
䛿䚸 䛣䛾䝽䜲䝲䞊䝃䝗䝹䛷ᅛᐃ䛥䜜䛶
䛔䜛䜿䞊䝤䝹䜢ゎᨺ䛧䜎䛩䚹
3
㻞 ⌧ᆅᡭ㓄䛾ᕤᮦ 䞉 ᕤල
㻟 ഛ䛾ὀព㡯
㻠 ᥋⥆⟽䛾ྲྀ᪉ἲ
䜰䜲䝪䝹䝖
㻹㻝㻜 䝪䝹䝖 䠄䜎䛯䛿
䝁䞊䝏䝪䝹䝖䠅
᥋⥆⟽
2
᥋⥆⟽
㻌㻌㻌㻌㻌㻌ᆺᘧ 㻵㻲㻙㻤㻡㻠㻜䚷ྲྀせ㡿᭩
ᮏ᭩䛿䚸 ᥋⥆⟽ 㻵㻲㻙㻤㻡㻠㻜 䛾ྲྀ᪉ἲ䛻䛴䛔䛶グ㍕ 䛧 䛶䛔 䜎䛩䚹 ᥋⥆⟽䛾ෆ㒊䛻䛿䚸 ฟⲴ䛾ᵝ㑅ᢥ䛻 䜘 䜚 䚸 ḟ
䛾䝴䝙 䝑 䝖 䛜ഛ 䛥 䜜䛶䛔 䜎䛩䚹
䐟䝉 䞁䝃䞊䜰 䝎䝥 䝍 䞊 㻹㻯㻙㻟㻜㻜㻜㻿㻙㻺㻌㻝 ྎ 㻗㻌㻹㻯㻙㻟㻜㻞㻜㻰㻙㻺㻌㻟 ྎ
䐠䝉 䞁䝃䞊䜰 䝎䝥 䝍 䞊 㻹㻯㻙㻟㻜㻜㻜㻿㻙㻺㻌㻝 ྎ 㻗㻌㻹㻯㻙㻟㻜㻞㻜㻰㻙㻺㻌㻠 ྎ
䐡䝉 䞁䝃䞊䜰 䝎䝥 䝍 䞊 㻹㻯㻙㻟㻜㻜㻜㻿㻙㻺㻌㻝 ྎ 㻗㻌㻹㻯㻙㻟㻜㻞㻜㻰㻙㻺㻌㻟 ྎ 㻗㻌㻹㻯㻙㻟㻜㻝㻜㻭㻙㻺㻌㻞 ྎ
㻵㻲㻙㻤㻡㻠㻜 䛾ෆ㒊䛻䛿䚸 㻹㻯㻙㻟㻜㻜㻜㻿 䜢ྵ䜑䛶᭱ 㻢 ྎ䛾䝉 䞁䝃䞊䜰䝎䝥 䝍 䞊䜢ഛ䛷 䛝 䜎䛩䚹 䐟䛚 䜘 䜃䐠䛾ሙྜ䛿䚸
䜸䝥䝅 䝵 䞁 䛷䝉 䞁䝃䞊䜰 䝎䝥 䝍 䞊 㻹㻯㻙㻟㻜㻝㻜㻭㻙㻺䚸 䜎 䛯䛿 㻹㻯㻙㻟㻜㻞㻜㻰㻙㻺 䜢㏣ຍഛ䛷 䛝 䜎䛩䚹 ㏣ຍഛ䜢⾜ 䛖 ሙྜ
䛿䚸 ḟ䛾䝉 䞁䝃䞊䜰 䝎䝥 䝍 䞊 䛸 ෆ㒊㓄⥺⏝䛾䜿䞊䝤䝹⤌ရ 㻖 䜢ᡭ㓄 䛧 䛶 䛟 䛰 䛥 䛔䚹
㻖 䠖 ㏣ຍ䝴䝙 䝑 䝖 䜈䛾㟁※౪⤥䛚 䜘 䜃ಙྕ㏻ಙ䛾䛯䜑䚸 ෆ㒊䛾䝉 䞁䝃䞊䜰 䝎䝥 䝍 䞊㛫䜢᥋⥆䛩 䜛 ᚲせ䛜䛒 䜚 䜎䛩䚹
㻝 ྎ䛾㏣ຍ䝴䝙 䝑 䝖 䛻ᑐ 䛧 䛶䚸 㻝 ᮏ䛾䜿䞊䝤䝹⤌ရ䜢‽ഛ 䛧 䛶 䛟 䛰 䛥 䛔䚹
㺃 ࢭࣥࢧ࣮ࢲࣉࢱ࣮㸦ᆺᘧ㸸MC-3010A-Nࠊሬ↓ࡋࠊࢼࣟࢢධຊ⏝㸧
䡡 ࢭࣥࢧ࣮ࢲࣉࢱ࣮㸦ᆺᘧ㸸MC-3020D-Nࠊሬ↓ࡋࠊࢹࢪࢱࣝධຊ⏝㸧
䡡 䜿䞊䝤䝹⤌ရ 䠄ᆺᘧ 䠖 AI.14-8AI.34-6L1000䚸 㒊ရ 䝁 䞊 䝗 䠖 000-177-250-10䠅
㻝 ྠᲕ≀