Professional Documents
Culture Documents
Full download Physical Chemistry Thermodynamics Statistical Mechanics and Kinetics 1st Edition Andrew Cooksy Solutions Manual all chapter 2024 pdf
Full download Physical Chemistry Thermodynamics Statistical Mechanics and Kinetics 1st Edition Andrew Cooksy Solutions Manual all chapter 2024 pdf
https://testbankfan.com/product/physical-chemistry-quantum-
chemistry-and-molecular-interactions-1st-edition-andrew-cooksy-
solutions-manual/
https://testbankfan.com/product/physical-chemistry-2nd-edition-
ball-solutions-manual/
https://testbankfan.com/product/thermodynamics-for-engineers-1st-
edition-kroos-solutions-manual/
https://testbankfan.com/product/mathematics-for-physical-
chemistry-4th-edition-mortimer-solutions-manual/
Elements of Physical Chemistry 7th Edition Smith
Solutions Manual
https://testbankfan.com/product/elements-of-physical-
chemistry-7th-edition-smith-solutions-manual/
https://testbankfan.com/product/principles-of-engineering-
thermodynamics-1st-edition-reisel-solutions-manual/
https://testbankfan.com/product/thermodynamics-an-interactive-
approach-1st-edition-bhattacharjee-solutions-manual/
https://testbankfan.com/product/physical-chemistry-principles-
and-applications-in-biological-sciences-5th-edition-tinoco-
solutions-manual/
https://testbankfan.com/product/thermodynamics-for-engineers-si-
edition-1st-edition-kroos-solutions-manual/
Another random document with
no related content on Scribd:
Thrills and Excitement That will Satisfy the Swimming Enthusiast and
Provide a New Summer Diversion at the Lake or River may be Had from
the Water Toboggan and Slide. It may be Adapted to a Smaller Size and
Built by Boys. The Details of the Toboggan and the Construction of the
Slide are Shown in the Sketches Above
The high end of the slide illustrated is about 7 ft. from the ground,
but a proportionately greater incline is provided because the beach
slopes gradually to the water’s edge. It is reached by a ladder fixed
to a tree, which acts as an end brace for the slide. If no such natural
support is available, the end of the slide must be strongly braced on
three sides, to insure safety. It is inadvisable to build the slide unduly
high to provide the necessary incline since this may result in
accidents. A location where the ground is suitable should be selected
rather than assume danger or risk.
The end of the slide nearest the water may be given a slight
upward turn, so that when the toboggan leaves it the rider is carried
upward before striking the water. The hold on the toboggan should
be retained when entering the water, as injury may result by failure to
clear it in the plunge. With experience a dive may be made as the
toboggan leaves the slide.
The construction of the slide is shown in detail in the lower sketch.
The framework of 2 by 4-in. material should be only slightly wider
than the guides, and the supports should be spread toward the
ground to give rigidity. The supports A should be nailed firmly, or
bolted, to the horizontal members B. If lighter stock is used, the
pieces at B should be nailed in pairs, one on each side of the
uprights. The guides C and D should be of smooth lumber, and the
edges of these pieces, as well as of the bearing plank E, should be
rounded off to remove splinters. The joints in the sections of the
guides should be made carefully and placed over the framework
supports. They should be reinforced from the lower side by plates of
wood.
The bearing plank E is of 2-in. stock and 12 in. wide. It may be
made of lighter material in a smaller slide. The joints in it should
likewise be made carefully, to insure smooth riding over them. They
should be set directly over the framework supports, but not on those
over which joints have been made in the guides. The plank forming
the bearing for the roller should not extend to the end of the slide at
the lower end, but should be set back about 18 in. This permits the
toboggan to slide off smoothly rather than to spring directly into the
air from the bearing on the rollers. The bearing plank may be nailed
into place, but care must be taken to set all nails below the surface.
A better construction is to use screws or bolts. Bore holes for them
through the plank, countersinking their heads.
The toboggan, as shown in the detail sketches, is built strongly,
and is to be fitted over the 12-in. bearing plank, allowing ¹⁄₄-in. play
on each side. The sides are of 1¹⁄₄-in. stock and high enough to
accommodate the rollers, which should be about 3 in. in diameter.
The dimensions of 15 in. in width and 30 in. in length, on the top
surface, are suggestive only, and will vary with the materials used.
The toboggan will not stand the necessarily hard wear unless good-
quality oak, or other hard wood, is used. The top and foot brace
should be fixed strongly with screws, their heads countersunk.
The rollers are fixed in the sides by means of screws, or a bolt
may be set through the length of the roller. In either case the bearing
should be in holes bored through the sidepieces. Washers should be
fitted at the sides of the bearings, and the latter must be kept
greased. All the edges and corners of the toboggan should be
rounded off so that there is little possibility of injury from slivers or
contact with the edges.
Tile Trap for Rabbits
By Closing the Smaller Opening, the Rabbit may be Trapped and Removed at
the Cover
Talking-Machine Records may be Played with the Finger Nail after a Little
Practice
This Chopping Block Makes for Safety in That Pieces are Thrown Away from
the Worker
Copper or Other Metal may be Deposited on the Surface of the Cup, Making
an Effective Inscription